Installation Instructions

ManualsBrandsCamden Door Controls ManualsElectronicsLazerpoint RF 915Mhz Advanced Single Relay Receiver

Page 1 of 7

Lazerpoint™ RF RX-90v2

Advanced Single Relay Receiver

INSTALLATION INSTRUCTIONS

Door Activation Devices

1. DESCRIPTION

CM-RX-90v2 receivers can be paired with Lazerpoint™ or

Kinetic™ transmitters, switch selectable.

Kinetic™ by Camden is an advanced 900 MHz 'power harvesting'

wireless system that uses the energy created by the operation

of the switch to power the wireless transmitter.

This Kinetic™ transmitter is available with the following push

plate switches: CM-45K, CM-46K, CM-7536K and CM-7509K.

Lazerpoint™ Radio Controls comprise the following models:

• CM-TX-9 Wall switch ready transmitter

• CM-TX-99 Plug-in transmitter

• CM-TXLF 1, 2 & 4 button fob transmitters

• CM-RX-90v2 Advanced single relay receiver

• CM-RX-91 Basic single relay receiver

• CM-RX-92 Full function (dual relay) receiver

Lazerpoint™ RF is the rst system designed to address the

specic needs of the Automatic Door industry. Unlike typical

“garage door” RF, Camden’s Lazerpoint™ operates at 915 MHz

frequency to “cut through” noise and clutter, penetrating typical

building materials to ensure a reliable installation.

Three receiver models are offered – the basic single relay RX-91,

the full function RX-92 and the advanced single relay RX-90v2.

The RX-90v2 offers 3 operating modes including delayed, no

delay and latched.

The CM-RX-90v2 supports both Lazerpoint™ RF and

Kinetic™ by Camden transmitters.

CM-RX-90v2 features a convenient terminal block, visual relay

status, and 40 code memory with push and learn technology.

2. FEATURES

• 3 Modes of Operation:

- Delayed (1 - 15 Seconds)

- No Delay (1 – 30 Seconds)

- Latching

• Adjustable Range: 3' - 300'

• 40 Transmitter capacity, either Lazerpoint™ or Kinetic™

either delayed, non-delayed or both

• Form ‘C’ Relay Output

• 12/24V AC/DC operation

• 915 MHz Lazerpoint™ or Kinetic™ Technology

• Small Size: 2-5/8”H x 1-1/2”W x 13/16”D (67mm x 38mm x 21mm)

3. SPECIFICATIONS

Operating Voltage 12/24V AC/DC

Current Draw

23 mA nominal @ 24 VAC

43 mA maximum @ 24 VAC

Response Time 30 – 200 ms

Memory Delay

& No Delay

40 transmitters total

LED’s

Indicate: relay status; learn mode;

erase mode & potentiometer position

Output 1 x SPDT Relay contact

Rating 3 amps @ 30 VDC

Operating Time 1 – 30 seconds

Delay Time 1 – 15 seconds

Frequency 915 Mhz.

Mounting 2-#4 screws at 3” centers or Velcro (supplied)

Enclosure Clear plastic case

Dimension 2-5/8”H x 1-1/2”W x 13/16”D

(67mm x 38mm x 21mm)

Summary of content (7 pages)

PAGE 1
Door Act i v a t i o n Dev i ces Lazerpoint™ RF RX-90v2 Advanced Single Relay Receiver INSTALLATION INSTRUCTIONS 1. DESCRIPTION 2. FEATURES CM-RX-90v2 receivers can be paired with Lazerpoint™ or Kinetic™ transmitters, switch selectable. • 3 Modes of Operation: Kinetic™ by Camden is an advanced 900 MHz 'power harvesting' wireless system that uses the energy created by the operation of the switch to power the wireless transmitter.
PAGE 2
LAZERPOINT™ RF RX-90v2 ADVANCED SINGLE RELAY RECEIVER INSTALLATI ON I N STRU CTIO NS 4. INSTALLATION MOUNTING The RX-90v2 receiver is designed to mount inside the automatic door header. Screw holes are located at each end of the receiver case, or the included velcro may also be used to hold it securely. For dimensional information refer to RX-90v2 electrical and mechanical Drawing on Page 4.
PAGE 3
LAZERPOINT™ RF RX-90v2 ADVANCED SINGLE RELAY RECEIVER I N S TA LL AT I O N INS TRUCTIO NS Latching Mode The RX-90v2 has a latching mode. Activating the transmitter will latch the output relay ON. Activating the transmitter a second time will latch the Relay OFF. DIP1 can be set to either ON/OFF. Adjust POT1 clockwise until the LED starts to flash. RX-90v2 is in latching mode at this point. To remove latching mode, turn POT1 counter clockwise until the LED is solid again.
PAGE 4
LAZERPOINT™ RF RX-90v2 ADVANCED SINGLE RELAY RECEIVER INSTALLATI ON I N STRU CTIO NS IC & FCC INFORMATION FOR USERS This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: 1. This device may not cause interference; and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
PAGE 5
POT1 1 2 NC POWER IN POWER IN NORMALLY OPEN COMMON NORMALLY CLOSED ORANGE AC/DC 12/24V NO COM DESCRIPTION PB1 WIRE COLOR ON RED RED BLUE GREY PB1 DIP 2 DIP 1 LATCH OP TIME ver 2.0 RX-90 3" [67mm] [77mm] 5 2 " 8 DRAWING No: DATE: 09/14/17 REVISED: 5502 Timberlea Blvd. Mississauga, Ontario L4W 2T7 FILE NAME: CM-RX-90_Mech.
PAGE 6
8 6 APPLICATION USED ON PB1 5 NEXT ASSY ON 7 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CAMDEN DOOR CONTROLS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CAMDEN DOOR CONTROLS IS PROHIBITED. 2 PROPRIETARY AND CONFIDENTIAL Learning the Transmitter in No-Delay Mode Step 1 - Set SW1 to OFF Step 2 - Press the PB1 button using a small blunt object such as a small blade screwdriver or similar.
PAGE 7
2 PB1 AC/DC DIP 2 DIP 1 NC 5 6 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CAMDEN DOOR CONTROLS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CAMDEN DOOR CONTROLS IS PROHIBITED. AC/DC 12/24V NO COM LATCH OP TIME RX-90 PB1 NC NO COM 12/24V ver 2.0 PB1 DIP 2 DIP 1 LATCH OP TIME ver 2.