Installation Instructions

Page 7 of 7
LAZERPOINT™ RF RX-90v2 ADVANCED SINGLE RELAY RECEIVER
INSTALLATION INSTRUCTIONS
Door Operator #2
TO OPEN
PUSH
Switch
& TX-9
CM-RX-90 Vestibule Wiring Diagram
CM-RX-90_Wiring_2.ai
JLEWIS 09/14/17
A
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
NEXT ASSY
USED ON
APPLICATION
MATERIAL
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
DATE
NAME
TITLE:
SIZE
B
DWG. NO.
REV
SCALE: 1:1
UNLESS OTHERWISE SPECIFIED:
SHEET 1 OF 1
DO NOT SCALE DRAWING
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL:
1/64
ANGULAR: MACH
0.5
BEND
TWO PLACE DECIMAL
0.010
THREE PLACE DECIMAL
0.005
PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CAMDEN DOOR CONTROLS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CAMDEN DOOR CONTROLS IS PROHIBITED.
5502 Timberlea Blvd. Mississauga, ON Canada
L4W 2T7
Tel: [phone]
www.camdencontrols.com
D
C
B
A
B
C
D
12 - 24 V
AC/DC Power
Door Operator #1
12 - 24 V
AC/DC Power
TO OPEN
PUSH
PUSH
TO
OPEN
PUSH
TO
OPEN
Vestibule
Switches
& TX-9 's
1
2
3 4
Switch
& TX-9
Receiver #1 Receiver #2
Red
Red
Blue
Grey
Red
Red
Blue
Grey
POT1
PB1
OP TIME LATCH
PB1
DIP 1 DIP 2
RX-90
ver 2.0
12/24V
NO
AC/DC
COM
NC
2
ON
1
POT1
PB1
OP TIME LATCH
PB1
DIP 1 DIP 2
RX-90
ver 2.0
12/24V
NO
AC/DC
COM
NC
2
ON
1
Programming the Transmitters into the Receivers: Set the Protocol with DIP2 ON= Kinetic
TM
OFF= Lazerpoint
TM
Receiver #1 Learning Transmitter #2 into Delayed Mode Step 1 - Set SW1 to ON (Delay Mode). Step 2 - Press the PB1 button using a small blunt object such as a small blade screwdriver or similar. Within 10 seconds, press switch #2 . The Green LED Array will ash to conrm enrolment. Step 3 - Pressing switch #2 again will signal the receiver that you are nished programming and the LED will ash rapidly. If you wait longer than the 10 second period, the receiver will time out of Learn Mode and revert back to standby. Step 4 - Adjust POT 1 for the delay time (1 - 15 Seconds). Learning Transmitters #1 and #4 into No-Delay Mode Step 1 - Set SW1 to OFF (No Delay Mode). Step 2 - Press the PB1 button using a small blunt object such as a small blade screwdriver or similar. Within 10 seconds, press switch #1 connected to a TX-9 transmitter or a button on a Lazerpoint FOB. The Green LED Array will ash to conrm enrolment. Step 3 - Repeat step #2 for switch #4. Step 4 - Pressing the learned transmitter again will signal the receiver that you are nished programming and the LED will ash rapidly. If you wait longer than the 10 second period, the receiver will time out of Learn Mode and revert back to standby. Step 5 - Adjust POT 1 for the relay Hold time (1 - 30 Seconds). Receiver #2 Learning Transmitter #1into Delayed Mode Step 1 - Set SW1 to ON (Delay Mode). Step 2 - Press the PB1 button using a small blunt object such as a small blade screwdriver or similar. Within 10 seconds, press switch #1. The Green LED Array will ash to conrm enrolment. Step 3 - Pressing switch #2 again will signal the receiver that you are nished programming and the LED will ash rapidly. If you wait longer than the 10 second period, the receiver will time out of Learn Mode and revert back to standby. Step 4 - Adjust POT 1 for the delay time (1 - 15 Seconds). Learning Transmitter s #2 and #3 into No-Delay Mode Step 1 - Set SW1 to OFF (No Delay Mode). Step 2 - Press the PB1 button using a small blunt object such as a small blade screwdriver or similar. Within 10 seconds, press switch #2 connected to a TX-9 transmitter or a button on a Lazerpoint FOB. The Green LED Array will ash to conrm enrolment. Step 3 - Repeat step #2 for switch #3. Step 4 - Pressing the learned transmitter again will signal the receiver that you are nished programming and the LED will ash rapidly. If you wait longer than the 10 second period, the receiver will time out of Learn Mode and revert back to standby. Step 5 - Adjust POT 1 for the relay Hold time (1 - 30 Seconds).