Summary The CAME-TV KUMINIK8 Duplex Digital Wireless Foldable Headset is easy to set up and provides about 450m/1500ft of open range between the Master and Remote headsets. There are two versions available, US for the US while EU for EU countries and other countries can use either version if it does not have the regulation on frequency use. This manual applies to model KUMINIK8-1R (single ear remote) , KUMINIK8-1M (single ear master), KUMINIK8-2R (dual ear remote) and KUMINIK8-2M (dual ear master).
Product Structure Single Ear Dual Ear 2
Operating Instructions 1.Power On/Off Power on: the headset will be powered on automatically when battery is installed. In the condition that battery is already in its compartment, one quick press the power button to turn on the headset. Power off: Press and hold the power button for around 5 seconds until power indicator changes off. Note: Power off the remote headsets first otherwise the master headset can not be powered off. 2.LED Indicators Master: red LED on earcup indicates master headset.
microphone only and you can still hear what everyone else is saying. 4. Volume Voice +: Raise the volume Voice -: Lower the volume 5. Pairing Headsets are paired at the factory and ready for use when they are powered on. For the headsets which already had been paired successfully, they can be connected automatically and no need to pair again. Note: If for some reason you need to re-pair the headsets here is the recommended procedure.
Then following steps should be proceed on the premise of that the led on the remote headset become solid after powered on. On the remote headset, press and hold on both volume + & buttons simultaneously until the Blue LED starts flashing quickly. The slowly flash on the remote headset indicates the process is completed. The same procedure goes for other headsets for pairing. Each master headset can be paired with 3 different remote headsets.
Quick Start and Tips Pair Master or Remote HUB How to quit pairing process How to Pair Short press Power Press and hold button on master on volume + & - ( Remote will quit buttons pairing automatically simultaneously and led indicator until the Red become solid if master Led indicator headset has already starts flashing. been paired with three remote headsets.
1.During pair process, master will always remain in pairing mode while remote needs to be paired one by one. 2.The master headset is not allowed to be in pairing mode if there are more than 2 master headsets. For example, Module one and Module two of the hub can not be in pairing mode at the same time. 3.If the remote has already been paired with master in Group A and this remote need to be paired with Group B master, in this case, the group A master needs to be turn off in advance. 4.
6. Each remote headset can be replaced with the hub to increase the number of the remote headsets and extend the working distance. How to Optimize the Communication Effect: 1. In order to get the best communication result, it is recommended to place the master (or HUB) in the center position, and the remotes are arranged around the master (or HUB) to ensure that each remote is within the working distance. 2.
4 Person Team, Max Distance 3000ft 9
7 Person Team, Max Distance 3000ft 10
9 Person Team, Max Distance 4500ft 11
HUB Description For our standard kits, the most connections available is a four headsets connection via a master headset with three remotes. To expand beyond that capability, we now offer a hub to provide connection up to 10 in one system. Normally a master headset can connect to three remotes, but in this configuration the hub is utilizing on of the three channels available to the master. The hub in turn communicates to two groups, with each group connecting to three headsets.
Remote C Remote B Master A HUB HUB M2 HUB R HUB M1 Remote I Remote H Remote G Remote F Remote E Remote D 13
7 8 9 1 2 3 4 5 6 See details in above picture: 1.Functional Button for Master Module 1 2.Functional Button for Remote Module 3.Functional Button for Master Module 2 4.Left Charging Indicator 5.Indicator for Remote Module 6.Right Charging Indicator 7.Indicators for Master Module 1 (It comes with 3 different indicators, from right to left numbered as 1,2,3 respectively.) 8.
9: Indicators for Master Module 2 (It comes with 3 different indicators, from right to left numbered as 1,2,3 respectively.) Hub can be charged with either one battery or two batteries. The built-in board will allocate the battery portion to the proper parts automatically. The hub can also be powered by standard 5V USB devices. Pairing Method for HUB Headsets of the 7 pieces kit and 9 pieces kit are paired at the factory and ready for use when they are powered on.
you want to combine them into one group more than 6 headsets, please follow guides below: 1.Turn on the master headset and at least one prepaired Remote headset or Hub in the kit (at most two units). 2.Press and hold the Volume + & - buttons at the same time on the master headset to activate pairing mode. Then perform a long press on #2 functional button of remote module on the Hub until the indicators flash quickly.
three different remote headsets. When the first remote headset is successfully paired with hub master module 1, the right indicator becomes solid and the second one flashes, then perform the same procedure to pair the second and third remote headsets. After three remote headsets are paired with hub master module 1, all led indicators in remote headsets and master module 1 will become solid.
headsets. 2.Make sure to quit the pairing mode by long pressing the function button for master module after all remote headsets are done pairing if less than 3 pieces remote headsets are needed. HUB Indicators Introduction: One: Indicators on remote modular 1. Flash quickly: Pairing mode 2. Flash slowly: Stand-by mode (It means the headset has already been paired, but has no connection to master, as the master is not turned on.) 3. Solid: Never been paired or working normally.
paired successfully, 1# indicator will become solid, then 2 and 3. Master module will quit pairing mode automatically if it is already been paired with 3 different remotes and start working. 2.4 In working mode, the number of the remote headsets will be the same as the indicators number. And the indicator number is the same as the pairing sequence. Three: Power Charging Indicators When charging, the battery indicator will flash slowly and become solid when fully charged.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
-- Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Compliance The device has been tested and comply with FCC SAR limits. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Warranty Card Name Phone Email Address Order Number RMA Number Reason of Return 22