AUTOMATION SYSTEM FOR SWING GATES FROG SERIES INSTALLATION MANUAL SUPERFROG
“IMPORTANT SAFETY INSTRUCTIONS FOR INSTALLATION” “CAUTION: IMPROPER INSTALLATION MAY CAUSE SERIOUS DAMAGE, FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY” “THIS MANUAL IS ONLY FOR PROFESSIONAL INSTALLERS OR QUALIFIED PERSONS” ENGLISH This symbol indicates sections to be read with particular care. This symbol indicates sections concernig safety. This symbol indicates notes to communicate to users. 2 Destination and limits of use 2.
1 GEARMOTOR UNIT 1) Tie rod 2) Motor support assembly 3) Gearmotor 4) Cover 5) Foundation box 6) Upper arm assembly 7) Arm assembly 8) Sleeve bearing 9) Hole cover for case 10) Bracket for case 2 3 ENGLISH 4 6 7 5 8 9 10 4.4 Dimensions Measurements in mm ^ The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users. 4.
5 Installation ENGLISH 5.
.3 Cable list and minimum thickness Type of cable Length of cable 1 < 10 m L. of cable 10 < 20 m L. of cable 20 < 30 m 4G x 2,5 mm2 4G x 4 mm2 4G x 1 mm2 4G x 1,5 mm2 4G x 2,5 mm2 2 x 0,5 mm2 2 x 1 mm2 2 x 1,5 mm2 2 x 0,5 mm2 2 x 0.
5.4 Preparing the foundation box - Dig a pit to place the foundation box into, set up the required cable boxes and corrugated conduits – for the connections coming from the branching pit – and the drainage tube. Note: the number of cables depends on the type of system and the accessories installed. - Fill the pit with concrete and sink the foundation box into it, making sure that the corrugated and drainage tubes pass through the proper holes.
- Lubricate the pinion of the foundation box, the sleeve bearing, the arm assembly and the upper arm assembly. Follow the diagrams to assemble properly. Upper arm assembly ENGLISH The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users. Arm assembly Sleeve bearing Pinion - Place the gate leaf above the upper arm assembly making sure that the hinge is secured properly.
5.5 Installing the motor unit N.B. the diagrams that follow show an outer view so as to make the (MD) right-hand gearmotor installation more intuitive. UNI 5588 M12 UNI 6592 Ø12 - Fasten the tie rod between the motor support and the arm assembly with nuts and bolts in the proper holes. UNI 7474 M12 UNI 5739 M12x80 UNI 5739 M20x50 Note: the arms are fitted with several holes to enable different gate-leaf opening angles.
ENGLISH The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users. - When the gate leaf is in the closed position, adjust the box bracket until it stops against with the motor arm assembly and fasten it. - Rest the cover on top of the foundation box, fix the hole cover into place and insert the cap into the cover. UNI 5933 M6x12 Cap Cover Hole cover for case 5.
6 Connecting up to the control panel When performing electrical connections, it is always advisable to do so using the branching pit or the cable boxes. For further guidance on functions and settings, read the technical documentation of the control panel. ZA2S Control panel 2 3 4 . /0 3%.3 ENGLISH /0 3%.3 /. /0 3%.3 R T 5 7 6 8 7 9 % % BROWN BLACK BLUE BROWN BLACK BLUE Power rating 400V A.C. triphase 50/60Hz S Connection for the delayed opening 400V A.C.
The unit does not require specific maintenance. Only as a precautionary measure and in case of intensive use, we recommend periodically checking (every 6 months) on the state of the electric wire connected to the motor, the tightness of the nuts and the proper oiling of the sliding points between fixed and mobile parts. All checks must be recorded (in a dedicated record-book).
CAME UNITED KINGDOM LTD UNIT 3, ORCHARD BUSINESS PARK TOWN STREET, SANDIACRE NOTTINGHAM - NG10 5BP - U.K. Tel 0044 115 9210430 Cod. 119AU03 ver. 0.
