Client Utility WLN-1306 802.
Contents Introduction............................................................................................................... 5 System Requirements ........................................................................................ 5 Profile Management ................................................................................................. 5 Create or Modify a Configuration Profile ...................................................... 5 Remove a Configuration Profile ..................
Current Status...................................................................................................16 Adapter Information Button..................................................................................16 Diagnostics Tab .......................................................................................................17 Transmitted Frames................................................................................................17 Received Frames...............................
Introduction The Client Utility is a user-mode utility designed to edit and add profiles for the 802.11n MPCI Module. System Requirements • • Laptop/ PC containing: • 32-bit PCI Express Bus • 32 MB memory or greater • 300 MHz processor or higher Microsoft Windows 2000, Windows Millennium Edition, Windows 98 Second Edition, Windows XP, or Windows NT 4.0 (with Service Pack 6) Profile Management Configure the wireless network adapter (wireless card) from the Profile Management tab of the Client Utility.
Remove a Configuration Profile 1. Go to the Profile Management tab. 2. Select the profile to remove from the list of configuration profiles. 3. Click the Remove button. Auto Profile Selection Management Including a profile in the auto selection feature allows the wireless adapter to automatically select that profile from the list of profiles and use it to connect to the network. Including a profile in auto profile selection: 1. On the Profile Management tab, click the Order Profiles button. 2.
Switching to a Different Configuration Profile 1. To switch to a different profile, go to the Profile Management tab. 2. Click on the profile name in the Profile List. 3. Click the Activate button. The Profile List provides icons that specify the operational state for that profile. The list also provides icons that specify the signal strength for that profile. Import and Export Profiles Importing a Profile 1. From the Profile Management tab, click the Import button. The Import Profile window appears. 2.
General Tab In the Client Utility, access the General tab by clicking New or Modify on the Profile Management tab. Edit the fields in the General tab to configure the configuration profile. Make sure to also edit the Security and Advanced tabs. Profile Name Identifies the configuration profile. This name must be unique. Profile names are not case sensitive. Client Name Identifies the client machine. Network Names (SSIDs) The IEEE 802.11 wireless network name. This field has a maximum limit of 32 characters.
Security Tab In the Client Utility, access the Security tab by clicking New or Modify on the Profile Management tab. Click the Security tab in the Profile Management window. Edit the fields in the Security tab of Profile Management to configure the profile. To define the security mode, select the radio button of the desired security mode. Make sure to also edit the General and Advanced tabs. WPA/WPA2 Enables the use of Wi-Fi Protected Access (WPA). Choosing WPA/WPA2 opens the WPA/WPA2 EAP drop-down menu.
None No security (not recommended). Using EAP-TLS Security To use EAP-TLS security In the Client Utility, access the Security tab in the Profile Management window. 1. On the Security tab, choose the WPA radio button. OR: On the Security tab, choose the 802.1x radio button. 2. Choose EAP-TLS from the drop-down menu. Enabling EAP-TLS security: To use EAP-TLS security, the machine must already have the EAP-TLS certificates downloaded onto it. Check with the IT manager. 1.
5. Click OK. 6. Enable the profile. Using PEAP (EAP-GTC) Security To use PEAP (EAP-GTC) security In the Client Utility, access the Security tab in the Profile Management window. 1. On the Security tab, choose the WPA radio button. OR: On the Security tab, choose the 802.1x radio button. 2. Choose PEAP (EAP-GTC) from the drop-down menu. To use PEAP (EAP-GTC) security, the server must have WPA-PEAP certificates, and the server properties must already be set. Check with the IT manager. 1.
Using PEAP-MSCHAP V2 Security To use PEAP-MSCHAP V2 security In the Client Utility, access the Security tab in the Profile Management window. 1. On the Security tab, choose the WPA radio button. OR: On the Security tab, choose the 802.1x radio button. 2. Choose PEAP (EAP-MSCHAP V2) from the drop-down menu. To use PEAP (EAP-MSCHAP V2) security, the server must have WPA-PEAP certificates, and the server properties must already be set. Check with the IT manager. 1. Click the Configure button. 2.
Using LEAP Security To use security In the Client Utility, access the Security tab in the Profile Management window. LEAP security requires that all infrastructure devices (e.g. access points and servers) are configured for LEAP authentication. Check with the IT manager. Configuring LEAP • • On the Security tab, choose the WPA radio button. Choose WPA-LEAP from the drop-down menu. OR: On the Security tab, choose the 802.1x radio button. Choose LEAP from the drop-down menu. 1. Click the Configure button.
Pre-Shared Encryption Keys Defining pre-shared encryption keys: 1. Click the Pre-Shared Key (Static WEP) radio button on the Security tab. 2. Click the Configure button. 3. Fill in the fields in the Define Pre-Shared Keys dialog box: Key Entry Determines the entry method for an encryption key: hexadecimal (0-9, A-F), or ASCII text (all keyboard characters except spaces). Encryption Selects the default encryption keys used.
Using WPA Passphrase Security To use WPA Passphrase security In the Client Utility, access the Security tab in the Profile Management window. 1. 2. 3. 4. On the Security tab, choose the WPA Passphrase radio button. Click on the Configure button. Fill in the WPA Passphrase. Click OK. Zero Configuration This section describes the operation of the Client Utility and Windows XP Wireless Configuration Service (WZCS).
To turn Zero Configuration off on Windows XP, take the following steps: 1. In Windows XP, open the Wireless Network Configuration Properties dialog box. 2. Clear the check box “Use Windows to configure my wireless network settings” to set Zero Configuration. When this check box is cleared, all profile settings are controlled by the configuration profile, which is set up from the Profile Management tab.
Card Name Name of the wireless network adapter. MAC Address MAC address of the wireless network adapter. Driver Driver name and path of the wireless network adapter driver. Driver Version Version of the wireless network adapter driver. Driver Date Creation date of the wireless network adapter driver. Client Name Name of the client computer. Diagnostics Tab The Diagnostics tab provides allows retrieval of receive and transmit statistics. The Diagnostics tab does not require any configuration.
Scan Available Networks Click the Scan button on the Profile Management tab to scan for available infrastructure and ad hoc networks. On this list, click Refresh to refresh the list at any time. Connecting to a different network • Highlight a network name and click the Activate button to connect an available network. If no configuration profile exists for that network, the Profile Management window opens to the General tab.
Display Settings To change the display settings, choose Options > Display Settings from the menu. The display settings dialog box contains tools to set the: Signal Strength Display Sets the units used when displaying signal Units strength: percentage (%) or dBm. Refresh Interval Use the up/down arrows to set the display refresh interval in seconds. Data Display Sets the display to cumulative or relative: • Relative displays the change in statistical data since the last update.
Tray Icon The tray icon appears at the bottom of the screen, and shows the signal strength using colors and the received signal strength indication (RSSI). Hold the mouse cursor over the tray icon to display the current configuration profile name and association, as well as transmit and receive speed and the wireless adapter name and IP address. Right-click on the tray icon to: Help Open the online help. Open Client Utility Launch the Client Utility.
Address Exit Exit the Client Utility application. The colors are defined as follows: Color Quality RSSI* Green Excellent 20 dB + Green Good 10-20 dB + Yellow Poor 5-10 dB Red Poor < 5 dB Gray No Connection No Connection *Received signal strength indication RSSI. Displayed in dB or percentage. Enable or disable the tray icon in the Action menu. Ad Hoc Mode In ad hoc mode, a wireless network adapter works within an independent basic service set (IBSS), as illustrated here.
• Transmit Power Level • 802.11b Preamble (if using 802.11b) • Wireless Mode When Starting an Ad Hoc Network Make sure to also edit the General and Security tabs. Infrastructure (Access Point) Mode In infrastructure (access point (AP)) mode, the wireless network adapter participates in a basic service set (BSS) as a station, and communicates with the other stations through an AP, as illustrated here. To connect to an access point network, configure the profile for access point mode.
Uninstall an Old Driver Uninstall an old driver before upgrading to a new NDIS driver release. To remove the newly installed driver from the system if the system does not have previously installed versions of the NDIS driver, proceed to Step 4. 1. To remove the NDIS driver from the OS, go to Device Manager, right-click Wireless Network Adapter, and choose Uninstall. 2. Click OK to uninstall the device. 3.
Advanced Status Information Click the Advanced button on the Current Status tab of the Client Utility to see advanced information about the program and its operations. The Current Status tab does not require any configuration. The following table describes the items found on the Advanced Status screen. Network Name (SSID) Displays the wireless network name. Configure the network name on the General tab. Server Based Shows whether server based authentication is used.
Compliance FCC Radio-Frequency Exposure Notice: FCC ID#: NHPWLN1306 This device generates and radiates radio-frequency energy. In order to comply with FCC radiofrequency radiation exposure guidelines for an uncontrolled environment, this equipment has to be installed and operated while maintaining a minimum body to antenna distance of 20 cm. The antenna(s) used for this transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
FCC Labeling instructions for OEM Integrators: Integrators of this module must add the following label. Contains FCC ID: NHPWLN1306 Above should be clearly visible on the outside of the products in which the module are installed. Industry Canada Notice: This device complies with Canadian RSS-210. To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding.
