Installation Guide

ManualsBrandsCAMO ManualsKitchen1-7/8 in. ProTech Coated Trimhead Deck Screw (350-Count)

100 98 96 94

BRAND BG - BLACK ONLY

100 98 96 94

BRAND BG - BLACK ONLY

Achieve a fastener-free surface on square decking with this easy

and aﬀ ordable hidden fastening system. MARKSMAN Tools

automatically establish spacing between boards and direct CAMO

Edge Screws into the edge of the board, leaving a smooth deck

surface. Plus, the MARKSMAN system is backed by a CAMO

warranty for use in leading deck boards.

MARKSMAN

INTRODUCTION 35

MARKSMAN PRO TOOLS 36

MARKSMAN EDGE 38

Summary of content (6 pages)

PAGE 1
ND BG - BLACK ONLY V2 100 V2 MARKSMAN Achieve a fastener-free surface on square decking with this easy and aﬀordable hidden fastening system. MARKSMAN Tools automatically establish spacing between boards and direct CAMO Edge Screws into the edge of the board, leaving a smooth deck surface. Plus, the MARKSMAN system is backed by a CAMO warranty for use in leading deck boards.
PAGE 2
MARKSMAN INTRODUCTION MARKSMAN PRO TOOLS MARKSMAN EDGE Get to know your MARKSMAN® tools HANDLE 96 94 TRIGGER SCREW CHANNEL SCREW CHANNEL THUMB DIAL TEETH SCREW CHANNEL DRIVE CONNECTION MARKSMAN PRO® MARKSMAN PRO-X1® MARKSMAN PRO-NB® MARKSMAN EDGE MARKSMAN tools are for exclusive use with CAMO Edge Screws WHICH TOOL SHOULD I USE? MARKSMAN PRO MARKSMAN PRO-X1 MARKSMAN PRO-NB MARKSMAN EDGE Gap 3/16 in. 1/16 in. 3/16 in. None Board Width 5-¼ to 5-¾ in. 5-¼ to 5-¾ in. 3-¼ to 5 in.
PAGE 3
ND BG - BLACK ONLY MARKSMAN INTRODUCTION MARKSMAN PRO TOOLS Setup for MARKSMAN Pro Tools MARKSMAN EDGE V2 100 V2 A INSERT T-15 BIT B DON’T USE DON’T USE IMPACT DRIVER Insert the T-15 driver bit into your drill. Do not use an impact driver. C ADJUST DRILL The recommended fastening speed for Edge fastening is 2500 RPM. IMPACT DRIVER Speed up the job by attaching the pre-drill bit to another drill.
PAGE 4
MARKSMAN INTRODUCTION MARKSMAN PRO TOOLS MARKSMAN EDGE How to fasten Edge Screws 96 94 BEFORE YOU BEGIN Where Edge fastening with the MARKSMAN Pro Tools isn’t possible, use CAMO Premium Deck or Composite Screws. Go to page 41 for full instructions. 1 2 3 PLACE TOOL DRILL HOLE* LOAD SCREWS Place the tool on the board so it’s in line with the joist. If you are NOT pre-drilling, skip to step 3. If pre-drilling, run the pre-drill bit through both screw channels*.
PAGE 5
ND BG - BLACK ONLY MARKSMAN Setup for MARKSMAN EDGE INTRODUCTION MARKSMAN PRO TOOLS MARKSMAN EDGE V2 100 A ATTACH YOUR DRILL V2 Attach the Drive Connection to your drill. NOTE: The MARKSMAN EDGE tool leaves no gap between boards. If you desire a gap, place secondary spacers before fastening.
PAGE 6
MARKSMAN INTRODUCTION MARKSMAN PRO TOOLS MARKSMAN EDGE How to fasten Edge screws 96 94 BEFORE YOU BEGIN Where Edge fastening with the MARKSMAN EDGE isn’t possible, use CAMO Premium Deck or Composite Screws. Go to page 41 for full instructions. 1 2 3 LOAD A SCREW PLACE TOOL ON BOARD DRIVE Load an Edge screw into the magnetized screw channel. Align the screw channel with the joist, ensuring the face of the tool is ﬂat. Drive the screw until it’s fully seated in the board.