Operation Manual

ManualsBrandsCamOne ManualsDigital CameraGravity Air 2D Gimbal

CamOne Gravity Air 2D Gimbal



Manual

This manual is available here: www.CamOneTec.com/gimbal

Vers. 1.0

"FlyCamOne" and „CamOne” are registered trademarks of ACME the game company GmbH, Germany

This user manual is protected by international copyright laws.

No part of this manual may be reproduced without the prior written permission of ACME the game company GmbH

in any form or by any means, electronic or mechanical, including Photocopying, recording or storing in any information storage and retrieval system,

reproduced, distributed, translated, or transmitted.

Summary of content (12 pages)

PAGE 1
CamOne Gravity Air 2D Gimbal Manual This manual is available here: www.CamOneTec.com/gimbal Vers. 1.0 "FlyCamOne" and „CamOne” are registered trademarks of ACME the game company GmbH, Germany © copyright 2014 ACME the game company GmbH This user manual is protected by international copyright laws.
PAGE 2
Safety advice SERVICE & SUPPORT WARNING: PLEASE NOTE THE FOLLOWING ADVICES TO AVOID SHOCKS OR DAMAGES ON THE PRODUCT: - DON’T USE THE PRODUCT WHEN RAINING, OR AT WET PLACES - KEEP THE DEVICE AWAY FROM WATER - ONLY USE ORIGINAL SPARE PARTS DO NOT DISMANTLE THE DEVICE. INSIDE ARE NO PARTS THAT CAN BE REPAIRED BY THE USER. THE SERVICE SHALL BE PERFORMED BY THE SUPPLIER OR PRODUCER. ACME the game company GmbH Boikweg 24 33129 Delbrück Germany Tel: +49 2944 9738 30 service@camonetec.com or http://www.camonetec.
PAGE 3
Content Please check the completeness before using the product! Gimbal Camerabail 2x Small parts, screws etc. Connection cables 2x Mountingbail Bellows 8x Retaining bracket 2x Mounting plate big Mounting plate small Required tool Allen 1,5 + 2,0mm Screwdriver Important note! More information, adjustments and tips are available 0n the CamOneTec webpage (http://www.CamOneTec.com).
PAGE 4
Index Safety advice……..………………...……………………………………………………………………………………..2 Content / Required components............………………………………….………………….….………………………3 Important notes....……………………………………………………………………………………………….…….…..3 Index....................…………………………………………………………………………………………………….……4 Disclaimer and warnings.......................…………..………………...…………………………………….…………….4 Connection / Mounting advice..……………………………….……………………………………………………….…5 Mounting………...…………………………………………..……………………….……………………………….…….
PAGE 5
Connection / Mounting advice Mounting Use the supplied screws to mount the unit. If there are no matching holes inside your RC models fuselage, please contact your supplier for further advice. Make sure that the screws are tightened before every flight. The Gimbal needs to be mounted downwards.
PAGE 6
1. Gimbal Mounting Screw the Mountingbail with 2 screws (M2x6mm) and spring washers with the Gimbal-System. The tabs shall point in direction of the camera holder. Use a 1.5mm Allen screwdriver to perform this work. Attach the mounting bracket with three screws (M3x8mm) on the small plate. Insert the screws through the plate and fasten them to the mounting bracket. 2. Bellows and mounting on the RC- Model Push the bellows into the 4 holes on the big mounting plate (see picture).
PAGE 7
When the bottom part of the Gimbal is completely mounted and screwed, insert the mounted bellows into the bigger plate. Make sure, that the side with the ports points to the lower plate. This work requires some patience. If this has been successful, connect the fixed cable from the Gimbal (white/wide plug) with the matching port P1 on the bigger plate. 3.
PAGE 8
Setting the Tilt Position On the big plate there are two buttons (S1/Down and S2/Up). With these, you can fix the camera orientation in the tilt position. This position can be fixed as following: Keep pressed both buttons for 5 seconds and then set the requested position through the particular button. You can reset this setting as following: Keep pressed both buttons for 5 seconds, release and push them again for 5 seconds.
PAGE 9
Settings on the DJI Naza-M V2 Software as an example: You can align the tilt position of the camera on the Gimbal via the rear X1-channel on the DJI Phantom Remote Control. Technical Details: - Operating temperature - Weight - Size Betriebsspannung / Working Voltage Feststehende Signaltaktrate/ static attiude tracking accuracy Bewegung Signaltaktrate / Motion attiude tracking accuracy Überlastschutz / Overload protection Zeit Überlastschutz / overload protection time Max.
PAGE 10
Spare parts and accessories for the DJI Phantom Multicopter Artikelnummer DJB100 DJB110 DJB111 DJB112 DJB113 DJB114 DJB115 DJB116 DJB117 DJB118 DJB123 DJB124 DJB128 HEOS0100 DJB131 HS1132 AA1119 Bezeichnung DJI Phantom Quadrokopter RTF-Kit DJI Phantom Propellerschutz DJI Phantom Landegestell DJI Phantom Ersatz Elektromotor DJI Phantom Propellerpaar 8x4,5 (1x Links /1x rechts) DJI Phantom ESC red front (rote LED´s) DJI Phantom ESC green rear (grüne LED´s) DJI Phantom Kompass Modul DJI Phantom Gehäuse Schale
PAGE 11
Guarantee The consumer is without prejudice to any claim against the seller a Manufacturer's Guarantee under the conditions set out below : » New devices and their components , or arising from manufacturing and / Material faults within 24 months of purchase develop a fault , are of ACME the game company GmbH exchanged at its option against a prior -art device to the original purchaser or repaired free of charge . For wear parts , this warranty is valid for 3 months from purchase.
PAGE 12
FPV (First Person View) The premier competition of model flight DJI Phantom + CamOne infinity + 5,8 GHz Transmitter Set and 7“ (178mm) Diversity Screen 12