CamOne Gravity Sports 3D Gimbal Benutzerhandbuch Vers. 1.0 "FlyCamOne" und „CamOne” sind registrierte Marken von ACME the game company GmbH, Deutschland © copyright 2014 von ACME the game company GmbH Dieses Benutzerhandbuch ist durch internationale Urheberrechtsgesetze geschützt.
Sicherheitshinweise WARNUNG: SERVICE & SUPPORT BEACHTEN SIE FOLGENDE HINWEISE, UM STROMSCHLÄGE ODER SCHÄDEN AM PRODUKT AUSZUSCHLIESSEN: - SETZEN SIE DAS GERÄT NICHT REGEN, FEUCHTIGKEIT, TROPF- ODER SPRITZWASSER AUS - HALTEN SIE DAS GERÄT UND ALLE BESTANDTEILE VON WASSER FERN - VERWENDEN SIE AUSSCHLIESSLICH EMPFOHLENE ZUBEHÖRTEILE - DEMONTIEREN SIE NICHT DAS GERÄT - IM INNERN BEFINDEN SICH KEINE TEILE, DIE VOM BENUTZER GEWARTET WERDEN KÖNNEN.
Lieferumfang Überprüfen Sie die Vollständigkeit bevor Sie das Gerät in Betrieb nehmen Gimbal Kamerabügel 2x 3x Adapter Typ 16340 3x Li-Ion Zellen Typ 16340 CamOne 3-Fachlader USB-Kabel 1x Wichtige Hinweise! Auf der Internetseite von CamOneTec (http://www.CamOneTec.com) finden Sie weitere Hinweise, Informationen und Anpassungen zu dieser Anleitung. Halten Sie sich unbedingt bei der Montage an diese Anleitung! Inhaltsverzeichnis Sicherheitshinweise………………...…………………………………………………………………………………......
Haftungsausschluss und Warnhinweise Lesen Sie diese Hinweise vor der Inbetriebnahme und Verwendung des Artikels und seiner Komponenten! Mit der Inbetriebnahme des Artikels erklären Sie sich mit den Bedingungen zum Haftungsausschluss und den Hinweisen einverstanden. Bauen Sie den Artikel gemäß der Anleitung auf. Jegliche Veränderungen an diesem oder Verwendungen von Fremdprodukten/Ersatzteilen kann zu Schäden führen.
Zusatzfunktion Der 3-Fachlader verfügt über die zusätzliche Funktion als „Powerbank“ zu agieren. Das bedeutet, dass über den zusätzlichen großen USB-Port Komponenten mit Spannung versorgt werden können. Sie können damit Ihr Handy, MP3-Player usw. laden. Verwenden Sie das mitgelieferte USB-Kabel, bzw. das passende Kabel Ihres Gerätes mit der großen USB-Buchse. Montage Verwenden Sie die beiliegenden Schrauben zur Befestigung.
Maximale Rotation der Achsen Beachten Sie, dass die einzelnen Achsen einen maximalen Ausschlag haben, siehe Bild. Bewegungen des Handgriffes welche größer sind können nicht ausgeglichen werden. Einlegen der Akkus Für den Betrieb des Gimbals werden die drei Li-Ionen Zellen aus dem Lieferumfang benötigt. Laden Sie diese mit dem beiliegenden Ladegerät. Dieses zeigt durch eine grüne LED den vollgeladenen Akku an.
Erste Inbetriebnahme Alle Bauteile wurden von Ihnen gemäß den vorangegangenen Punkten beachtet und montiert. !Inbetriebnahme nur mit installierter Kamera! Äußerliche Krafteinflüsse im Betrieb beschädigen den Gimbal! Bewegen Sie den Gimbal (Kopf/Kamerahalter) im Betrieb nicht per Hand. Achten Sie darauf, das sich die Motoren komplett auf ihrer Achse frei bewegen können und kein Kabel verklemmt ist. Halten Sie den Gimbal-Griff senkrecht und unbewegt fest, betätigen Sie den Ein-/Aus Schalter.
USB- Anschluss und Taster Mit dem auf dem Handgriff angebrachten Taster können Sie den Betriebsmodus des Gimbals ändern. Ebenfalls zeigt Ihnen dieser anhand einer integrierten LED den aktuell eingestellten Modus an. Eine Übersicht hierzu finden Sie weiter unten. Über die USB- Schnittstelle können Sie zukünftige Firmware- Updates aufspielen. Weitere Informationen erhalten Sie über unsere Homepage.
Gewährleistung & Garantie Dem Verbraucher wird unbeschadet seiner Mängelansprüche gegenüber dem Verkäufer eine Haltbarkeitsgarantie zu den nachstehenden Bedingungen eingeräumt: »Neugeräte und deren Komponenten, die aufgrund von Fabrikations- und / oder Materialfehlern innerhalb von 24 Monate, ab Kauf einen Defekt aufweisen, werden von ACME the game company GmbH nach eigener Wahl gegen ein dem Stand der Technik entsprechendes Gerät dem Erstkäufer kostenlos ausgetauscht oder repariert.
CamOne Gravity Sports 3D Gimbal Manual Vers. 1.0 "FlyCamOne" and "CamOne" are registered trademarks of ACME the game company GmbH, Germany © copyright 2014 by ACME the game company GmbH This user manual is protected by international copyright laws.
Safety Advice SERVICE & SUPPORT WARNING: Follow these instruction to prevent damage of the unit: • DO NOT USE UNPROTECTED IF RAIN OR WATER. PREVENT CONTACT WITH ANY KIND OF LIQUIDS • USE RECOMMENDED ACCESSORIES ONLY • DO NOT DISASSEMBLE • THERE ARE NO PARTS AT THE INSIDE THAT NEED TO ME MAINTAINED REPAIRS SHOULD BE MADE BY QUALIFIED PERSONNEL ONLY ACME the game company GmbH Boikweg 24 33129 Delbrück Germany Phone: +49 2944 9738 30 service@camonetec.com or http://www.camonetec.
Content of the box Please check the completeness before you use the product. Gimbal Camera bracket 2x 3x Adaptor for Typ 16430 3x Li-Ion cells Typ 16340 CamOne Triple Charger USB-Cable 1x Important Note! More information and updates on this manual are available at CamOneTec (http://www.CamOneTec.com). Please follow this manual before you assemble the product! Index Safety advice……...………………...…………………………………………………………………………………......2 Content of the box / required components………………………………….……………….….………………….
Disclaimer and Warnings Read these instructions before commissioning and use of the product and its components! With the launch of the product, you agree to the terms of the disclaimer and agree to the instructions. Assemble the items on according to the instructions. Any changes to this or uses of Third-party products / spare parts can cause damage. This excludes the acquisition of warranty claims! The product is already in a functional state in the delivery condition. Take your time to start it.
Mounting Use the enclosed screws for mounting. The gimbal comes with two brackets for the following camera models: -CamOne infinity -GoPro Hero 3 / 3plus series Choose the matching bracket for your camera. Take care when mounting the bracket that it is not tilted or jammed. Place the camera as shown on the below picture. Screw it with the supplied M2x22 screws.
Maximum Rotation of the Axis Please note that every axis has a maximum deflection as shown below. More bigger movements can’t be corrected. Inserting the batteries For the operation of the gimbal, the three Li-Ion cells from the content are required. Charge these with the included charger. This is indicated by a green LED on, when battery is fully charged. If all three cells are charged, place them with the positive pole towards the gimbal head, one after the other into the handgrip.
Activation All components were observed and mounted by you in accordance with the previous points. !DO ONLY ACTIVATE WITH INSERTED CAMERA! External influences while use may damage the Gimbal! Do not move the Gimbal (head and camera mount) by hand! Make sure that the motors can move freely on their axis and that the cables are not stuck. Hold the Gimbal-Grip upright and motionless and then press the Power Switch. The LEDs of the motors will flash in blue.
USB- Port and Button To change the modes of the Gimbal, it is necessary to use the white button on the Grip. This button does also show the current mode by an integrated LED. Below you will find a detailed description. Future firmware updates can be installed through the USB- Port. Please visit our homepage for further information. Working modes See below how to change the modes! Heading Follow Mode (Mode 1) >> Single Press: The pitch angle remains fixed.
Warranty The consumer is without prejudice to any claim against the seller a Manufacturer's Guarantee under the conditions set out below: » New devices and their components , or arising from manufacturing and /Material faults within 24 months of purchase develop a fault , are of ACME the game company GmbH exchanged at its option against a prior -art device to the original purchaser or repaired free of charge . For wear parts, this warranty is valid for 3 months from purchase.
CamOne Gravity Sports 3D Gimbal Manuel d’utilisation Une version en ligne est disponible sur : www.CamOneTec.com/gimbal Vers. 1.0 "FlyCamOne", “CarCamOne”, CamOne Infinity, CamOne Xplore et le logo FlyCamOne HD” sont des marques déposées par la société ACME the game company GmbH, en Allemagne © copyright 2014 de ACME the game company GmbH. Ce manuel est protégé par un copyright international.
Conseils de sécurité Avertissements: SERVICE & SUPPORT Il est indispensable de suivre les instructions ci-après afin d’éviter d’endommager votre caméra: ACME the game company GmbH Boikweg 24 -NE PAS UTILISER LA CAMERA EN CONDITIONS PLUVIEUSES SI CELLE-CI N’EST PAS PROTEGEE -MAINTENIR A L’ECART DE L’HUMIDITE -N’UTILISER QUE LES ACCESSOIRES COMPATIBLES -NE PAS TENTER DE DEMONTER -AUCUN COMPOSANT INTERNE NE NECESSITE D’ENTRETIEN PARTICULIER -LES REPARATIONS NE DOIVENT ETRE FAITES QUE PAR LE PERSONNEL QUALIFI
Contenu de la boite Assurez-vous que votre produit est complet avant la première utilisation! Nacelle Adaptateurs pour caméra x 2 Adaptateur pour 16430 x3 3x Batteries Li-Ion 16340 CamOne Chargeur triple Cordon USB x1 Information importante! Plus d’informations de réglages et de conseils sont disponibles sur notre site, CamOneTec (http://www.CamOneTec.com). Respectez scrupuleusement ce manuel pour le montage ! Index Conseils de sécurité...……………...…………………………………………………………………………………......
Avertissements Veuillez lire attentivement ce manuel avant la mise en marche du matériel et l’utilisation de l’un des composants! En commençant à utiliser le matériel vous reconnaissez avoir pris connaissance des avertissements légaux et vous êtes d’accords avec ces derniers. Assembler le produit comme indiqué dans ce manuel. Tout changement dans les opérations de montage pourrait affecter et ou endommager le bon fonctionnement du produit.
Montage Utiliser les vis fournies avec le produit. La nacelle est livrée avec deux adaptateurs afin de s’adapter à ces différentes caméras: -CamOne infinity -GoPro Hero 3 / séries 3 plus Vous devez alors choisir l’adaptateur qui correspond à votre caméra. Veillez à ce que le montage de l’adaptateur soit fait avec précaution. Pour cela, positionner la caméra comme illustré sur la photo ci-après. Sécuriser le tout avec les vis M2x22 livrées avec le produit.
Charge et mise en place des batteries Pour fonctionner, la nacelle a besoin des trois batteries Li-Ion livrées d’origine. Vous devez les recharger à l’aide du chargeur inclus. Un témoin LED vert vous indiquera lorsque la charge est terminée. Une fois rechargées, les trois batteries doivent être positionnées comme illustré ci-après. Vous devez vous assurer de respecter la bonne polarité avant de refermer le logement des batteries. Ne pas introduire de corps étrangers dans le logement des batteries.
Description des témoins LED Port USB et boutons Pour changer le mode de la nacelle, il est nécessaire d’utiliser le bouton blanc qui se trouve sur le manche grip. Ce bouton vous permettra également de visualiser le mode sélectionné grâce à un témoin LED intégré. Ci-après vous trouverez la description des différents modes. Les nouvelles versions du microprogramme “firmware” pourront être installées vie le port USB. D’autres informations seront disponibles sur notre site internet.
Modes et fonctions Ci-après vous trouverez les informations sur les différents modes et fonctions! Mode suivi du mouvement (Mode 1) >> Une seule pression: L’angle du pitch reste fixe. La tête de la caméra va alors suivre le mouvement du manche. Pour ajuster l’angle du pitch, vous devez entrer dans le mode 2 et ajuster la tête de la caméra selon le mouvement du manche. Par la suite vous pouvez retourner dans le mode 1. Ce mode est automatiquement activé lors de la mise en marche de la nacelle.