CM-709M2 7” 4CHANNEL DIGITAL MONITOR INSTRUCTION MANUAL Thank you for purchasing this product. For proper usages and application, Please read this instruction manual thoroughly.
CONTENTS SAFEGUARD INSTRUCTIONS.................................... 3 FEATURE............................................................................ 5 CONTENT ....................................................................... 5 FUNCTION OF EACH PART........................................ 6 FUNCTION ........................................................................ 8 SETTINGS.......................................................................... 13 CONNECTING AND INSTALLATION ...........
SAFEGUARD INSTRUCTIONS 7” 4CHANNEL DIGITAL MONITOR Please read the “Safety Rules” carefully before using this product. Following the safety rules prevents users from damages related with the misuse of the product. It is very important to follow these safety rules. We state “Caution” and “Warning” to clarify any potential risk for a damage associated with the misuse of the product. NOTICE CAUTION WARNING This information is for user’s reference for better usability.
WARNING Do not install the product where sudden temperature increasing could be and use the optimum voltage, temperature and humidity. - It may cause electronic shock or malfunction. Take care that the product doesn’ t get wet. - It may cause electronic shock or malfunction. Do not place near of air bag effective range. - It may cause malfunction of air bag or accident, injury due to hitting monitor by air bag. Keep cleaning dust on power socket. - It may cause electronic shock and fire by bad connection.
1 • • • • • • • • • • • FEATURE 7” 4CHANNEL DIGITAL MONITOR 7” Wide digital TFT LCD with high resolution and low reflection All functions are displayed on screen (OSD function) 7 language display (ENG-DEU-ITA-FRA-ESP-KOR-JPN) DC 12~24V Touch buttons in front and including remote control Max.
3 FUNCTION OF EACH PART 7” 4CHANNEL DIGITAL MONITOR [MONITOR] SENSOR (REMOTE) 6 AV MODE DOWN/UP MENU POWER ① IR-SENSOR IR-SENSOR ② AV Go into AV mode directly and change to AV input ③ MODE Choose split screen (Full/2/3/4 split), choose audio output ④ DOWN/UP Choose cam input on full screen mode, split mode and change on split screen, volume control, menu setting change ⑤ MENU OSD menu on/off, screen input information ⑥ POWER Power on/off
[REMOTECONTROLLER] ① ③ ② ⑤ ④ ⑥ ⑦ ⑧ ⑨ ⑫ ⑪ ⑩ ① POWER Power On/Off ② AV Go into AV mode directly and change to AV input ③ OK Choose button on menu ④ ◀▶ Menu setting adjusting ⑤ ▲▼ Choose full screeen mode and menu adjusting ⑥ VOL +/- Volume control ⑦ MUTE Mute On/Off ⑧ SETUP OSD Menu setup ⑨ RECALL Actual settings ⑩ Go into 2 split screen ⑪ Go into 3 split screen ⑫ Go into 4 split screen 7
4 FUNCTION 7” 4CHANNEL DIGITAL MONITOR 1 POWER ON/OFF AV MODE DOWN/UP MENU POWER After connecting cigar jack, press POWER button on remote control or monitor then the picture of the camera will be shown on the monitor. ※ I f there is no image, the screen will be BLACK. CAM1 CAM 1 image signal receive No image signal 2 VOLUME CONTROL AV MODE DOWN/UP MENU POWER Press VOL +/- button on remote control or Down/Up button on monitor to adjust volume.
3 MUTE ON/OFF Press MUTE[ ]button on remote control for MUTE function ON/OFF. When MUTE is ON it will be displayed. It disappears for a while OSD MENU is used. ※ When user controls volume while mute function is set, the mute function turns off. MUTE 4 SCREEN SPLIT MODE SWITCH : FULL / 2 / 3/ 4 SPLIT AV MODE DOWN/UP MENU POWER Press M(Mode) on monitor, then the screen switches as below order.
5 CHANGE SPLIT MODE AV MODE DOWN/UP MENU POWER Each split screen has two options. On split mode, press DOWN/UP button of monitor or split screen button of remote control then the screen switches between both options. 2SPLIT 3SPLIT 4SPLIT 2SPLIT 3SPLIT H 4 SPLIT 6 CHANGE INPUT 1) Camera mode AV MODE DOWN/UP MENU POWER On split or AV mode, press ▲ button on remote control (or UP button of monitor) then it will change camera input of CAM1~CAM4 as below order.
2) AV mode AV MODE DOWN/UP MENU POWER On camera mode, press AV button of monitor or remote control then the screen goes to AV mode directly. AUX1 AUX2 3) SPLIT mode AV MODE DOWN/UP MENU POWER To choose the OSD MENU [SETUP] on each split mode, press menu button of monitor or SETUP button of remote control. • Split screen User can change camera mode on each split screen. Press M(MODE) button of monitor or DOWN/UP button of remote control and choose a Camera.
7 SCREEN SWITCH WHILE TRIGGER INPUT or is when a circuit works by a signal, for example if driver uses right/left turn signal or reverse gear, the monitor shows connected camera on driving mode. ※ Below example is based on {TRG1 (Left turn signal)=CAM1 / TRG2 (Right turn signal)=CAM2 / TRG3 (Reverse gear)=CAM3 / TRG4 (Front or something else)=CAM4 }.
3) W hen there is the TRG3(Rear light) input, CAM3 will be shown as full screen and user can also choose 2 split screen. ※ This function is available for rear and side screen. CAM1 CAM3 CAM3 Press ▼button of remote control (or DOWN button of monitor), then it shows 2 split screen as right for CAM3 (Rear) and left for CAM1. When the reverse gear input, the screen displays CAM3 (Rear) as full screen.
5) When there is an input signal of more than 2 triggers, the monitor displays fully connected screen (Trigger input screen) as the priority order.
5 SETTINGS 7” 4CHANNEL DIGITAL MONITOR 1 Video Standard System, NTSC/PAL conversion If use PAL system on NTSC system using country, it may cause a malfunction. This products can convert NTSC/PAL system manually but it is not automatic. Before use, please check and set the system. Attention AV NTSC system country : USA, CANADA, JAPAN, KOREA, TAIWAN, MEXICO PAL system country : AUSTRALIA, BELGIUM, CHINA, DENMARK, FINLAND, GERMAN, U.
3 Brightness and contrast setting User can control BRIGHT/CONTRAST/COLOR/HUE/SATUREATION. ※ Each menu is set 50 from the factory. AV MODE DOWN/UP PICTURE SETUP DIMMER BRIGHT CONTRAST HUE SATUREATION LANGUAGE VIDEO SYSTEM RESET AUTO 50 50 50 50 ENGLISH NTSC > MENU POWER 1) Press SETUP button of remote control (or MENU button of monitor) to go into OSD MENU [PICTURE SETUP].
5 Initialization ※ It initializes monitor as from the factory mode. (Except on Video Standard System, NTSC/PAL) AV MODE DOWN/UP PICTURE SETUP DIMMER BRIGHT CONTRAST HUE SATUREATION LANGUAGE VIDEO SYSTEM RESET AUTO 50 50 50 50 ENGLISH NTSC > MENU POWER 1) Press SETUP button of remote control(or MENU button of monitor) to go into OSD MENU [PICTURE SETUP].
7 Screen Information AV MODE DOWN/UP MENU POWER Press MODE button of monitor or RECALL button of remote control, then it displays actual screen information (Input mode / Audio output / Volume). CAM1 CAM2 CAM3 CAM4 VOLUME 30 8 CAMERA Mirror/Normal mode setting AV MODE DOWN/UP MIRROR SET CAM1 CAM2 CAM3 CAM4 MIRROR MIRROR MIRROR MIRROR MENU POWER 1) Press SETUP button of remote control (or MENU button of monitor) to go into OSD MENU [MIRROR SET].
6 CONNECTING AND INSTALLATION 7” 4CHANNEL DIGITAL MONITOR ⑤ TAPPING SCREW T1 M4.0 X 12 (3ea) INSERT BOLT (2ea) FLAT WASHER M3 (4ea) ⑥ ⑥ (1) Clean the place where to install stand and install stand firmly after removing protect tape of stand bottom. (2) Fix the stand with enclosed screws. (3) Assemble the monitor to stand and fix it in the right angle. (4) Connect cable as follows. NOTICE VELCRO TAPE VELCRO TAPE ※ Installation can be changed as user’s pleasure.
LEFT CAMERA (OPTION) RIGHT CAMERA (OPTION) CVBS YELLOW (VIDEO2) WHITE (AUDIO2) REAR 2 REAR1 LEFT RIGHT BLACK (REAR) GREEN (LEFT) ORANGE (RIGHT) YELLOW (VIDEO1) WHITE (AUDIO1) RED (DC JACK) REAR 1 CAMERA (OPTION) REAR 2 CAMERA (OPTION)
7 SPECIFICATION 7” 4CHANNEL DIGITAL MONITOR NTSC Screen size 7 inch Resolution WVGA (800 X 480) Brightness 250 cd/m2 LCD Panel Contrast ratio 70/70/45/55 Voltage DC 12V-24V Current 500mA (DC 12V, monitor set only) Input system Frequency Output signal 400 : 1 View angle(L/R/U/D) Power supply Input signal PAL NTSC/PAL Horizental 15.734 KHz Vertical 59.94 Hz Video signal Composite video signal (CVBS) Audeo signal MONO Video signal Composite video signal (CVBS) Speaker 0.
INSTRUCTION MANUAL PRINTED IN KOREA ver. 1.
