SPECIAL NAVIGATION INSTRUCTION MANUAL CN-900 (Navigation only) CN-900R (Rear view) CN-900T (Rear view + Telematics)
CONTENTS SAFEGUARD INSTRUCTIONS ..................................................... 3 FEATURES .......................................................................................... 6 SAFEGUARD INSTRUCTIONS Please read the “Safety Rules” carefully before using this product. Following the safety rules prevents users from damages related with the misuse of the product. It is very important to follow these safety rules.
WARNING Do not install product in direct sunlight, high temperature of humid areas. - It may cause to electronic shock or malfunction. Please use this product within the voltage range specified. - It may cause to electronic shock or malfunction. Power socket should be clean at all times. - It may cause electronic shock and fire by bad connection. Do not clean the exterior of the monitor using harsh abrasives or solvents. - It may cause change of surface, fall of paint, malfunction and fire.
Please take care below notice for built-in battery. We do not have responsibility for damage caused by not complying below rules. Built-in battery is an auxiliary usage for safe saving recording image while the power is not supplied. Please connect and use main power supply for normal recording. - Unless connect main power supply, it does not work properly. 2 BOX CONTENTS • Before use this products, please check below contents. If there is something missing parts, please contact sales agent.
3 FUNCTION OF EACH PART 4 PREPARATION 1. SD CARD The SD card that included in the package contains map information. Before you use the monitor, please insert the SD card to the slot. 2. BATTERY Built-in type battery will work if the power supplying is off (turn the ignition off). 1. CHARGING BATTERY If the power is connected, the battery is charging automatically with Red LED and it turns Green when the charging is completed.
5 OPERATION 1. POWER ON/OFF and RUN NAVIGATION 3. POWER ALERT This monitor has built-in battery. When you turn the ignition off of the vehicle and switch on of the monitor, it displays as below. Please press [OK] if you want use the monitor with battery. In case of setting of initial booting or system initialization, it showed up the setting window for coordinate value after booting logo screen.(refer to 14 page) 4.
1. SYSTEM SETUP 6 CONFIGURATION Press [M] button long (more than 3 seconds), then it goes to configuration mode. 1. SELECT STANDARD TIME ZONE - Set the standard time zone of the country by touching [+],[-] button. 1. SYSTEM : General setting - STANDARD TIME - DAYLIGHT SAVING TIME - LANGUAGES - AUTO DIMMER - POWER SAVING MODE - SYSTEM INFORMATION - DEFAULT FACTORY SETTING 2. CALIBRATION : Touch coordinate setting 2. DAYLIGHT SAVING TIME - Set the daylight saving time 3.
2. CALIBRATION If touch screen is not working well, please set up the “Calibration”. Please touch the icon [CALIBRATION] to enter the touch coordinate setting. Please touch the cross mark(+) exactly on the center of screen. When the cross mark is touched, it goes to the next step. If all setting is finished, the system is going to restart automatically. 3. REAR CAMERA SETUP 1. BRIGHTNESS - Please set up the brightness with touching the [<], [>] buttons. 2.
7 FIRMWARE UPDATE * This product’s firm ware update will be made through SD card. Please follow below procedure for updating. 1. Copy the [_update] folder in the SD card’s root folder. The camera microphone sound will be output when it is become the full screen mode in condition of “ON” at camera microphone. Also, the microphone volume could be controlled by using the side button. If the camera is not connected or the microphone is not supported, this function will not be operated normally. 2.
8 INSTALLATION 1. SUCTION STAND 9 CABLE CONNECTION Navigation (Standard) Stand bracket Angle control lever 1. Assemble the monitor body and stand as like the picture. 2. Adjust the angle and fix it with the bolt. 3. Clean the window before absorption and fix it pulling the lever firmly. Bracket bolt Angle control lever CIGAR CABLE Navigation + Rear view REAR CAMERA (OPTION) 2. STAND (CL-5) Screw 1. Please connect the stand bracket with the downward and back of product. 2.
10 TROUBLESHOOTING Q The screen does not turn on. Q It doesn’t upgrade for product. A - Please check the update file whether it is put correctly into the SD card. - It should have update files inside “[__update]” folder of SD card. A - Please check the power supply. (Please make sure the power switch is “ON”) - Please check the status of Stand-by. (Please push the S/B button.) - Please check the residual quantity of battery. (Please use the product after charge the battery.
11 SPECIFICATIONS MEMO Navigation (Standard) CPU MEMORY NAND FLASH OPERATING SYSTEM GPS CHIPSET BATTERY Core Logic CLG-7700 ARM11 800MHz DDR II 256MB 128 MB Windows CE 6.
INSTRUCTION MANUAL PRINTED IN KOREA ver. 1.0 * Design and specifications are subject to change without notice.
