CSA-1300P/1400P Automatic, auto-adjusting Satellite antenna Instruction Manual Vers. 1.5 Thank you for purchasing our product. Please read this instruction manual carefully before mounting and operating this antenna! Please write down the serial number of this antenna. In case of questions please inform us of this number: Ser.-Nr.
The Camos CSA-1300P/1400P enables reception of the major European satellites like ASTRA1, ASTRA2, HOTBIRD, SIRIUS, ATLANTIK BIRD 3 and HISPASAT. If you want to watch TV or access the Internet via satellite, here’s the equipment you need. The sat-dome is compact in size, light in weight, reliable in operation and incredibly easy to operate and install: there are just two cables to run. So the system’s simplicity and neatness makes it an attractive alternative to conventional dish systems. 1.
screw hole antenna foot antenna dome 4. Replace the antenna. Clean the mounting place and the antenna feet with the supplied special cleaning fluid "Reiniger1" and the supplied fleece (please wear the supplied Latex gloves!). Grind the marked fixing areas and antenna feet with sandpaper (not too much, the surface must be rough a little bit only), clean the surface and antenna feet with cleaning fluid 1 again and wait another 10 minutes. Attention! Now do not touch the cleaned surface any more! 5.
3. Connections Do not mount the Control box and your satellite receiver in the area of the vehicle's airbags! Lay the cables carefully to avoid short circuit! Pay attention to existing cables! 1. Connect the antenna by plugging the long white cable into antenna and control box. 2. Put the gel cap over the antenna socket. Gel cap 3. Connect the power cable (red/black) to the control box and power source (car battery e.g.).
4. Starting up and operating LNB indicator On/off switch Power indicator Lock indicator Satellite select pushbutton Satellite indicators 1. Switch on your satellite receiver and monitor/TV. Now you can switch on the control box. The green "LNB" indicator lights up after switching on the receiver. 2. Switch on the control box. The red indicator of the preset satellite lights up. The red "POWER" indicator lights up, the red indicator of the preset satellite starts blinking, then lights up continuously.
ASTRA 2-S please select when you are in the southern part of ASTRA2 footprint. ASTRA 1 please select for Astra 1 HOTBIRD please select Hotbird SIRIUS please select for Sirius ATLANTIC BIRD 3 please select for Atlantic Bird 3 HISPASAT please select for HISPASAT On the move it is normal that obstacles like tunnels, trees or buildings cut the direct connection to the satellite. In this case no reception is possible. 5.
Digital SAT-Receiver blackbox CI USER’S MANUAL Copyright Homecast Europe GmbH V1.
Contents 1 Before Starting 1.1 1.2 1.3 2 Controls and Functions 2.1 2.2 2.3 3 How to connect the Receiver ............................................................................................. 11 Menu-Overview 4.1 4.2 4.3 5 Front Panel .......................................................................................................................... 8 Rear Panel ...........................................................................................................................
Contents 6 Viewing General Operation 6.1 6.2 6.3 Banner Information ............................................................................................................ 30 TV & Radio Changing ........................................................................................................ 31 TV or Radio Channel Lists ................................................................................................. 31 6.3.1 6.3.2 6.3.3 6.3.4 6.3.5 6.3.6 6.4 Program View ...................
1. Before Starting Read this manual carefully and make sure you understand the provided instructions. For your safety, check what the result each action will be. 1.1 Warnings, Cautions and Notes Throughout the whole manual, pay special attention to the following marks that indicate hazardous situations. Caution Indicates a situation which, if not avoided, could damage the equipment or apparatus. Warnings Indicates a hazardous situation which, if not avoided, could result in serious injury.
1. Before Starting This digital satellite receiver has been manufactured to comply with international safety standards. Please read the following safety precautions carefully. Safety Instructions and Precautions Avoid placing heavy things and blocking ventilation passage. (Passage blocking can cause fire) Avoid scrubbing the surface with Benzene or Volatile gasoline. Color can be damaged. Leave the power and the antenna off for the long absence or during thunder storm.
1. Before Starting Keep away from the water Clear of the dust. Dust or Metallic particles inside the set can cause fire and electric shock. Avoid dissembling and assembling. Do not open the set. Do not snatch the cable to plug out. Keep the distance from Magnetic items and Audio Speaker. . Place the set with the good ventilation and away from the direct sunlight and humidity. Avoid the temperature over 30° C and below 5° C Copyright Homecast Europe GmbH V1.
1. Before Starting 1.2 Recycling Units which are furnished with this icon are not allowed to normal bin. Batteries are also not allowed to normal bin. 1.3 Accessories - Operating Instruction (this Manual) - Batteries (2x Typ AAA 1,5V) - SCART to CHINCH adapter - Remote Control - AC/DC Adapter 230VAC - Car-Adapter 12VDC - Remote Eye Copyright Homecast Europe GmbH V1.
2. Controls and Functions 2.1 Front Panel 1 5 2 6 3 7 4 8 9 10 1. Stand-By indicates stand-by mode 2. Card IN indicates inserted CI-card 3. LED-Display displays channel and/or time 4. IR-Sensor receives signal of the remote control 5. POWER key to switch on or off 6. MENU / OK key to enter menu mode and confirms operation 7. EXIT key leaves the menu mode / exits any operation 8. ◄ ► Keys volume control or navigates in menu mode 9.
2. Controls and Functions 2.2 Rear Panel 1 3 4 2 5 6 7 8 1. DISH IN to connect the lead of your dish 2. AUDIO (L/R) connect to your stereo amplifier 3. IR-Sensor plug in the external IR remote eye 4. LOOP OUT to connect such as additional analog receiver 5. S/PDIF digital (optical) audio out 6. TV SCART to connect the TV-set / monitor 7. RS-232C to connect with the computer for software update 8. DC-in to connect 12V or 24V power source Copyright Homecast Europe GmbH V1.
2. Controls and Functions 2.3 Remote Control 1. POWER: turns the receiver on or off 2. TV/STB: switches between TV and SAT mode 3. Menu: display the main menu of the receiver and come out from inner level to viewing mode (exit all) 1 4. EPG: starts the TV/Radio channel guide. 3 5. TV/Rad: switches between TV and Radio mode 6 6. / : moves up down in menu mode 7. P+/-: change channels up and down 8. V+/-: increase or decrease volume level 9.
3. Connect Receiver 3.1 How to connect the receiver Connection of receiver and TV-unit Connect the TV set by using a fully featured SCART cable to the “TV-Scart” socket of your receiver. Connection of receiver and Sat antenna Connect the satellite antenna cable tot he DISH IN socket Connection of receiver and hi-fi system If you want to use your HiFi-System for audio output, connect the „AUDIO OUT“ by using a RCA-cable to your HiFi-System. 3.2 Connecting the Receiver to an optical A/V Receiver .
4. Menu Overview 4.1 Menu Instruction Main menu Sub menu - Press the Menu button to display the menu. - You can select the Sub menu using / / / button. The selected Sub menu becomes highlighted. - When you have selected the Sub menu you want, press the (OK) button. - When you want to return tot he previous menu, press the - When you want to return tot he live screen, press the Menu button. button. 4.2 Menu Help In the menu, short information is displayed at the bottom of the screen.
4. Menu Overview 4.3 Menu-structure Installation - Dish: - Auto Scan: Select the dish and LNB Settings for channel search. Search the channel oft he selected satellite automatically without inputting the special parameters. - Manual Scan: Search the channel manually with user’s supplied parameters. - Transponder: Delete, edit and add satellite or transponder parameters.
5. Menu Operation 5.1 First Installation You can install the receiver using the menu item „First Installation” for your convenience. This menu item allows you to set your receiver using simple procedure. a) Select the desired language using the / button. b) Press the (OK) button to confirm and go tot he next step. a) Select the desired channel using the / button. b) Press the (OK) button to confirm. In step 2 you have the alternative between Astra 1, Hotbird, Astra 1 + Hotbird Default channels.
5. Menu Operation a) Select LNB Type using the / button. b) Press the (OK) button to confirm and go tot he next step. a) If you use a DiSEqC 1.0 switch, select DiSEqC option using the / button. b) Press the (OK) button to confirm and go tot he next step. a) After all settings are done, press (OK) button to start scanning. If you want to know more detail description about each procedure, please refer tot he following installation in part 5.
5. Menu Operation 5.2 Installation 5.2.1 Dish a) Press the Menu button to display the main menu. b) Press the (OK) button on the sub menu. The password pop-up window appears. All sub menus such as Dish, Auto Scan, Manual Scan and Transponder Edit on the Installation are locked by password. The default password is „0000“. a) Use the / button, you can move upwards and downwards in this mode. b) In any item, such as Dish, Satellite, Transponder etc.
5. Menu Operation a) Press the / button to watch the satellite in the pre-programmed list. Press “OK“ button to replace the current satellite with the selected satellite. a) Press the / button, the right screen shows the transponder lists. b) Press the (OK) button to select other transponder. If you select one oft he alternative satellite names, the transponder list is changed automatically according tot he selected satellite name. a) Select one oft he LNB Power types using / button.
5. Menu Operation a) Select Switch Type if used. b) If you use DiSEqC 1.0 switch, select DiSEqC on the Switch Type. c) Select one oft he DiSEqC inputs from the Option. a) Select Switch Type. b) If you use a DiSEqC 1.1 switch, select SMATV on the Switch Type. c) Enter a value with the numeric key (950-2150). . a) Select Switch Type. b) If you use a DiSEqC 1.2 motor, select „Motor“ on the Switch Type. c) Change position of your Motor through the Option. DiSEqC 1.
5. Manu Operation a) Select Switch Type. b) If you use an USALS motor, select from the Switch Type using the / button. c) Change position on your USALS motor through the Option. „Go to Position“: Press the (OK) button to move the motor tot he position calculated by the longitude and latitude. a) „Go to“ allows you to go tot he Auto Scan or Manual Scand Mode directly. b) Select „Auto Scan“ or „Manual Scan“ and press the “OK” button. 5.2.
5. Menu Operation a) b) c) d) e) Select Free+CAS or CAS using the / / / button. Press the Opt, CAS Pop-up window will appear. Select the kind of CAS using the / button. Press the “OK” button. If you want to scan the satellite, move to „Start Scan“ and press “OK” button. a) The left window shows TV channels and the right window shows Radio channels during the scanning process. White channel names are new channels downloaded to your receiver. Black channel names are already existing channels.
5. Menu Operation Dish: Frequency: Polarity: Symbol Rate: Code-Rate: Scan Mode: The target satellite for the manual scan.. The frequency oft he transponder you want to find manually.. The polarity oft he transponder you want to find. The Symbol Rate of the transponder you want to find. The code rate oft he transponder you want to find. In the Free Channel mode, the receiver scans all channels without scrambled service.
5. Menu Operation 5.2.4 Transponder edit a) Press the Opt button to select the satellite in the left screen or the transponder in the right screen. b) Select one of Delete, Edit or Add from the pop-up window. (The satellite and transponder cannot be deleted it the channels of the selected satellite have already been Downloaded). c) If you press the (OK) button, the current changing state will be saved and exit. 5.3 Option 5.3.1 TV-Output a) Select the TV output options using the / / / button.
5. Menu Operation 5.3.2 Language a) Select the language options using the / button. b) Press the (OK) button to change the selected language. Display: Audio 1-2: Subtitle 1-2: Change the language used in the OSD and Menus Change the language that you listen to audio in. Change the language that you watch the subtitle in. 5.3.3 Time Setting a) Setting current time using the / / / button b) If you press the (OK) button, current changing state will be saved.
5. Menu Operation 5.3.4 Parental Control a) If you want to change the password (0 0 0 0), press the / button, following message requiring new password will be displayed. b) Change the password into new one by numeric button c) To ensure your change, you are supposed to input a password once more. d) Select your desired rating level using the / button. e) Press (OK) button to save and exit. Rating mode allows you to block channel according to the age level you have set.
5. Menu Operation 5.3.5 OSD Display a) Select the options using the / / / button. b) If you press the (OK) button, current changing state will be saved and exit.
5. Menu Operation 5.4.2 Timer-Settings How to adjust the timer for recording on VRC. For recording the TV programs you can use the timer-function. Up to 8 programs can be pre-adjusted. a) Open the EPG by using EPG key and choose the desired program by pressing the / / / arrow keys b) Press red OPT key to confirm. a) Additional options, such as changing the pre-programmed starting time, can be adjusted. b) Press the OK button to save and exit.
5. Menu Operation : Just one time action (after action was done, event will be deleted on the list) : Action execution in weekday : Action execution in weekend : Action execution weekly :Action execution daily : TV channel : Radio channel 5.4.2 Delete You can delete channels. You can select not only Mode such as Channel, Satellite and CAS, but also Option such as TV, Radio etc. a) Select the Mode and Option you want to delete channels using the / / / button b) Press the (OK) button to delete and exit.
5. Menu Operation 5.5.2 Software update via Satellite (OTA) You can upgrade the latest software. The receiver checks whether the new S/W is released when you view channels or select this OTA menu. If the new version is detected, the receiver will be rebooted automatically and the download screen will appear. Remark: On the way of downloading, if the following message would appear, contact the manufacturer of receiver for errors. If any S/W can not be found, this following message will appear.
5. Menu Operation 5.5.3 Software Upload a) Connect the receiver with another receiver of PC through RS-232. b) For the target receiver, turn the AC Power off, then turn on again. c) You can watch the transfer status of software. 5.6 Status (Receiver) 5.6.1 Information a) You can watch the system information such as Model ID, Hardware version, Software version und Loader version. 5.6.
6. General Operation 6.1 Banner Information Teletext Audio Subtitle Language Lock PayTV Dolby Parental Control Detailed Event Information Channel Number and Name Current Time Current Event Name Event Progress Bar Signal Strength Bar Signal Quality Bar TV or Radio a) Whenever you press the INFO button, the banner information window appears for a few seconds. a) If you press the INFO button again on the banner, the detail EPG window appears.
6. General Operation 6.2 TV & Radio changing While watching TV or listening to Radio, you can change the mode using the TV/Rad button. 6.3 TV or Radio Channel Lists Programmliste Selection Screen Channel Name Information about the membership of the favorite-lists Status der Fav.-Listen Kanaldaten Anbietername View Delete Move Rename Lock Group Copyright Homecast Europe GmbH V1.
6. General Operation 6.3.1 Program – „View“ a) To open the program list please use OK or A-Z (sorted channels) button. b) Use the / buttons to move the cursor. c) Press OK button to choose the desired channel. d) The INFO button shows you detailed information about the current event. e) Please use the keypad 1-9 of your remote control to choose the desired channel directly. f) Press the button for exit. a) If you wish an alphabetic order, you have to sort your program list firstly.
6. General Operation 6.3.2 Program – „Delete“ a) Use the / button to select the Delete Icon. b) Select the channel you want to delete with the / button and confirm with the OK button. button to save the adjustment and to exit. c) Press the 6.3.3 Program – „Move“ a) Use the / button to select the Move Icon. b) Select the channel you want to place on another position and confirm with the OK button. c) Choose the new position with the / button. d) To finish the sorting please press the OK button.
6. General Operation 6.3.6 Programs /Favorites‘ List – „Rename“ a) Please close all menus and press the OK button to open the program list. b) Use the / button to select the Rename Icon. c) Select the channel you want to rename and press OK button. A small window appears. d) The letters can be select by pressing the / / / buttons and by confirming with OK button. e) As soon as renamed the channel please press the button and the OK button finally. button to exit.
6. General Operation 6.3.5 Program – „Lock“ a) Please close all menus and press the OK button to open the program list b) Use the / button to select the Lock Icon. c) Select the channel you want to lock and press OK button. The following advice will appears: d) „Please insert keyword“ (factory setting 0 0 0 0). To back up please press OK button again. e) Press the button to save and exit. 6.3.6 Favorites list – „Setup Groups“ You can setup up to 8 lists. Every list can contain up to 100 programs.
6. General Operation 6.4 Option Press the OPT button to open the Option-Menu. Here you have the option between “audio”, “teletext” and “subtitle”. To select please use the / button. 6.4.1 Audio-Language a) Select „Audio“ by using the / button. b) Use the / button to select the desired audio-language. c) Press OK button to confirm the selection. 6.4.2 Teletext a) Select „teletext“ by using / button. b) Press OK button to start teletext.
6. General Operation 6.5 A/V + Press A/V+ to start the Audio/Video menu. 6.5.1 Audio-Mode a) Select the audio mode by using the / button. b) Use the / button to choose the desired option: STEREO, LEFT, RIGHT and JOINT (Joint Stereo). c) Press OK button to confirm. button for save and exit. d) Press 6.5.2 Video-Mode a) b) c) d) 6.5.3 Select the video mode by using the / button. Use the / button to choose the aspect ratio. Press OK button to confirm. button for save and exit.
6. General Operation 6.5.4 Mosaic Screen a) The mosaic screen gives you a brief overview about the current programs. b) Select the menu item mosaic mode by using the / button firstly. c) Select now the desired mosaic mode by using the / button. d) The mosaic starts with the last used program and continues. e) By using the / , / arrow keys you can choose a program what has to be updated. f) Copyright Homecast Europe GmbH V1.6 Press the button to exit.
6. General Operation 6.6 Favorites List a) By using the Fav button you can start the applied favorites’ lists. b) Use the / arrow keys for selection or the ALL button for the complete list. c) Press OK button to confirm. . a) The functions within lists will be as same as in the complete list. b) You can resort and rename them up to your desires. . 6.6 A-Z Sorting a) Press A-Z button to get an alphabetically sorted list.
6. General Operation 6.8 EPG (Electronic Program Guide) Press the EPG button to start the electronic program guide. und den elektronischen Programmführer zu starten. The showing information will be provide by the local television station. Title of the broadcast Time bar a) Choose your program by using the / / / arrow keys. b) After finalize your selection press OK. a) For detailed information press the INFO button. b) Press the button to exit. Copyright Homecast Europe GmbH V1.
7. General Information 7.1 Features ! One CI-Slot ! 4000 Program Storage Capacity ! Electronic Program Guide EPG ! Fast Teletext ! 8 Favorits‘ Program lists ! DiSEqC Version 1.0, 1.2 and USALS compatible ! One-Cable-Solution ! Software-Update via Satellite and RS-232 connection ! 1 Scart-Connection ! multilingual OSD menu ! Blindscan search all channels received from your antenna ! External infrared eye with 3 meter length ! Power supply 12/24VDC Copyright Homecast Europe GmbH V1.
7. General Information 7.2 Technical Data A. HF-Bereich SAT-ZF-Frequency RF Input Signal Level RF Impedance Demodulation HF-Modulator 950 MHz to 2150 MHz -25 to -65 dBm 75 Ohm QPSK K 21 – K 69 B. Video Video-Decoding Video-Data Rate MPEG-2 1,5 – 15 Mbit/s C. Audio Audio-Decoding Sampling Rate Audio Mode MPEG-1/2, Layer 1/2 32 / 44,1 / 48 kHz Stereo, Co-Channel, Joint Stereo, Mono D.
7. General Information 7.3 Glossary CAS Conditional Access System CI Common Interface DiSEqC Digital Satellite Equipment Control EPG Electronic Program Guide FEC Forward Error Correction FTA Free to Air LNB Low Noise Blockconverter, MPEG Moving Picture Experts Group PID Packet Identification PIN-Code Personal Identification Number Copyright Homecast Europe GmbH V1.
7. General Information 7.4 How to solve malfuntions There may be various reasons for the abnormal operation oft he receiver. Check the receiver as stated bellow: Problem Cause Measure The display is nothing showing The power cable is not connected Please check the power cable No picture or sound Wrong connection of the audio/video outputs. Please check the connection and pay attention to the input and output circuit. The antenna is not adjusted adequately.
INSTRUCTION MANUAL 17” DIGITAL TFT LCD COLOR MONITOR CM-1710D/TM-1710D (Option) Thank you for choosing this product. Please read this instruction manual carefully before operating this product.
1. Safety Rules Contents 1. Safety Rules 3 2. Before Use 8 Please read the “Safety Rules” carefully before using this product. Following of the safety rules prevents users from any damage related with the misuse of this product. It is very important that users follow these safety rules. We state “Caution” and “Warning” to clarify any potential for damage associated with misuse of the product. Warning 3. Special Features of the product 10 4. Terms of part 11 5. Remote Control 12 6.
Do not use in bathtub. Do not pull the plug with wet hands. ---This may cause electric shock. Do not use unapproved power voltage. ---This may cause fire or electric shock. Caution Do not use unapproved Cigarette Lighter Adapter. --- This may cause fire ,electric shock and/or malfunction. Do not put the product in a place where sudden temperature increase occurs such as the vehicle’s dashboard. Do not damage or bend electric cord. Do not place heavy objects on electric cord.
Unplug the product and remove cords when moving. --- It may damage cords and cause fire and/or electric shock. The car engine should be running when you use the product in a car. ---Without the engine running, you may have excessive discharge of the car battery. Do not pull the cord line when you unplug it. ---Damaged cords may cause fire and/or electric shock.
2. Before Use Precautions (when you use the product in a car) =To safely use the product, please read the user’s manual carefully before use. =Connect all lines as directed in the product connection map in the manual. =Do not touch the LCD panel. =Use the product at the temperature range of 0OC ~ 50OC . =Screen may be a little dark when the product is operated in low temperature areas. Screen will be shown normal luminosity after a few minutes.
3. Special Features of the Product 4.
5. Remote Control ① ③ TV/AV POWER ② ④ ⑥ ⑤ CH RECALL SLEEP ⑧ MENU ⑦ VOL AUTO PIC CH PICTURE SETUP ⑩ SOUND ⑫ ⑪ 1 2 3 4 5 6 7 8 9 ⑬ 0 A.MEMO. ⑭ 12 Power ON/OFF Key ⑫ SOUND Sound selection button ② TV/AV Select TV, external video, s-video, DVI, D-sub analog ⑬ 0~9KEY Changes CHANNEL by selecting numbers directly (only TM-1710D) ③ RECALL Displays present status and volume level ⑭ A.MEMO.
6. Functions ※( ), it means a remote control button. 3 MENU (MENU) 1 POWER (POWER) AV/ S-VIDEO =POWER ON/OFF KEY ① Push POWER(POWER) button. POWER is on. PICTURE(PICTURE) ② Push POWER (POWER) button again. POWER is OFF. 2 SELECT(TV/AV) =It is function to change external video signals to DSUB ANALOG/ DVI/ VIDEO/ S-VIDEO/ TV DSUB ANALOG/ DVI DIGITAL/ AV/ S-VIDEO/ TV 55 CONTRAST 40 SHARPNESS 14 ※ With VOL ▶, go to SUB MENU. After adjusting in SUB MENU, press MENU to exit.
SETUP(SETUP) SOUND(SOUND) ▶ ENGLISH LANGUAGE OSD TIME 10 TRANSLUCENT 14 ※ With VOL ▶, go to SUB MENU. After adjusting in SUB MENU, press MENU to exit. MUTE OSD H POS. OSD V POS. FACTORY RESET VOLUME 10 TREBLE 50 BASS 50 OFF ① LANGUAGE Change language English, France, German , Spanish , Italian, Japanese, Korean. ① MUTE Mute the sound temporarily. Mute is released when you change channel and adjust volume.
TV Mode (only TM-1710D) CH PICTURE(PICTURE) TV ※ With VOL ▶, go to SUB MENU. After adjusting in SUB MENU, press MENU to exit. TYPE CHANNEL ① BRIGHTNESS Adjust the brightness of video. ② CONTRAST Adjust the contrast of video. ③ SHARPNESS Adjust the sharpness of video. COLOR TINT ④ COLOR TINT Change the richness of color. COLOR TONE ⑤ COLOR TONE Change the tone of color.
PC (ANALOG) COLOR PICTURE BRIGHTNESS 75 ※ With VOL ▶, go to SUB MENU. After adjusting in SUB MENU, press MENU to exit. The tone of color can be changed from red-dish white to bluish white. The individual color components are also user customizable. CONTRAST H POSITION USER 50 ※ With VOL ▶, go to SUB MENU. After adjusting in SUB MENU, press MENU to exit. V POSITION PHASE PIXEL FREQ. RED 14 GREEN 100 BLUE 20 ① BRIGHTNESS Adjust the brightness of video without affecting RGB s brightness.
DISPLAY MODES PC (DVI) For the display modes listed below, the screen image has been optimized during manufacture. PICTURE BRIGHTNESS 75 ※ With VOL ▶, go to SUB MENU. After adjusting in SUB MENU, press MENU to exit. Mode CONTRAST H POSITION VGA Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) Pixel Clock Frequency(MHz) Sync Polarity (H/V) 720 x 400 31.469 70.087 28.322 -/+ 640 x 480 31.469 59.940 25.175 -/- 640 x 480 37.500 75.000 31.500 -/- 800 x 600 37.880 60.
4 RECALL Displays present status and volume level. 5 AUTO PIC TV channel scan and memory. 6 SLEEP Sleep timer(0/10/20/30/60/90/120) 7 TV/CATV Select TV, external video, s-video, DVI, D-sub analog. 10 OSD MESSAGE OUT OF RANGE NO SIGNAL 8 MUTE ① The screen shows this when signal is out of range. ② The screen shows this when there is no signal. It is a function of Mute control. When you push MUTE button, OSD display this image. This image can be toggle. 9 CH.
7.
8. Changing Remote Control Battery 9. Specifications CM-1710D/TM-1710D 1. Slide and open the battery cover. SPECIFICATION ITEM LCD PANEL SIZE 43.18cm (17.0 INCH) MAKER SAMSUNG(LTM170EU-L11 & L21) NUMBER OF PIXELS 1280 X 1024 0.264(H) X 0.264(V)mm PIXEL PITCH 2. Insert new batteries and ensure that the polarities are correct when inserting. BRIGHTNESS 300cd/㎡ CONTRAST RATIO 500 : 1 VIEW ANGLE CR≥5 75˚ / 75˚ / 75˚ / 60˚(L/R/U/D) DISPLAY COLOR 16.2M VIDEO DIGITAL SIGNAL (DVI) ANALOG R.G.
MEMO SPECIFICATION ITEM POWER, MENU, SELECT, ▼▲, ◀▶ S/BY LED, REMOTE SENSOR WINDOW USER CONTROLS OSD DISPLAY LANGUAGES POWER SUPPLY VOLTAGE CONSUMPTION 7 LANGUAGES DC 12V 36WATT SOUND SIGNAL DIMENSION ( W X H X D ) OPERATING TEMPERATURE STORAGE TEMPERATURE WEIGHT 2WATT STEREO 422(W) X 371(H) X 38.5(D)mm 0 oC~ + 50 oC o o -20 C~ + 60 C 4.
