INSTRUCTION MANUAL Thank you for purchasing this product. For correct use and application, please read this instruction manual thoroughly. SV-420 / SV-430 REAR-VIEW SYSTEM FOR VEHICLE PRINTED IN KOREA * Design and specifi cations could be changed without notices. ver. 1.
CONTENTS REAR-VIEW SYSTEM FOR VEHICLE SAFEGUARD INSTRUCTIONS ......................................... 4 FEATURE ..............................................................................6 BOX CONTENTS ................................................................. 6 FUNCTION OF EACH PART .............................................. 7 FUNCTIONS ........................................................................ 8 INSTALLATION ................................................................
SAFEGUARD INSTRUCTIONS REAR-VIEW SYSTEM FOR VEHICLE Please pay attention to the warnings and cautions listed in order to prevent the potential risks. “WARNING” and “CAUTION” symbols are divided according to the different level of risk. CAUTION WARNING This information is for preventing damage or shorten the life time of the products. This information is for preventing bodily harm or even death and use should follow this safety rules. CAUTION Should install while power off.
WARNING Do not put the product in place where sudden temperature increasing and should use on optimum voltage, temperature and humidity. Do not place near of air bag effective range. - It may cause malfunction of air bag or accident, injury due to hitting monitor by air bag. Keep clean dust on power socket. - It may cause electronic shock and fire by bad connection. Do not pull cord with a jerk, should catch a plug and pull. Do not use damaged cord.
1 FEATURE REAR-VIEW SYSTEM FOR VEHICLE [ CM-430 MONITOR ] • Adopting high resolution LCD panel • All functions are displayed on screen (OSD function) • 5 languages display selection (ENG-DEU-ITA-FRA-ESP) [ CM-200 CAMERA ] [ CM-36 CAMERA ] • 1/3” 960H color CCD • 5 pcs of IR LEDs for night • Waterproof (IP67) • Audio Built-in • Heating function Built-in • Die-casting housing • Photo sensor • 1/3” 960H color CCD • 6 pcs of IR LEDs for night.
3 FUNCTION OF EACH PART REAR-VIEW SYSTEM FOR VEHICLE [ CM-430 MONITOR ] 4.3” TFT LCD (480x272) Max. 0.5W(MONO) 1. Display - 5. Speaker 2. MENU Menu setting and change 6. Cable Guidance - 3. Volume Volume setting 7. Bracket 4.
4 FUNCTIONS REAR-VIEW SYSTEM FOR VEHICLE [ CM-430 MONITOR ] 1. Power ON/OFF 1) POWER ON : If you push, POWER ON. (STAND BY state is OFF) 2) POWER OFF : If you push again, POWER OFF. 2. Button function MENU button The menu changes [BRIGHTNESS] - [CONTRAST] - [COLOR] [TINT] - [DIMMER] - [LANGUAGE] - [MONITOR] - [RESET] every push [MENU] button. Volume / Setting changes ·[VOLUME] : Volume control When you push△▽ button, it controls volume normally. (0~100) [0 : Min. volume / 100 : Max.
·[COLOR] : Density adjusting on screen color COLOR 50 On Color setting mode, △▽ buttons control density of screen color. (0~100) [0 : Low density / 100 : High density] ·[TINT] : Screen color adjusting On Tint setting mode △▽ buttons control screen color. (0~100) TINT 50 ·[DIMMER] : Automatic brightness adjusting DIMMER DAY On Dimmer setting mode, the menu changes [DAY] - [NIGHT] every pushing △▽ buttons. • DAY : Making bright screen conpulsorily. • NIGHT : Making dark screen compulsorily.
5 INSTALLATION REAR-VIEW SYSTEM FOR VEHICLE MONITOR INSTALLATION 1. Remove protecting tape from below of stand and attach stand with double stick tape. 2. Fix a stand with enclosed 3 screws. 3. Connect stand and monitor.
SV-420 CAMERA INSTALLATION (CM-200) 5 5 2 2 3 5 5 1 6 4 2 2 6 1. Determine a position and direction of installation and attach a camera bracket using double stick tape and screws. 2. Connect a camera and sun visor with bracket on vehicle and fix them with screws. 3. Run the cable as following cable connection guide. SV-430 CAMERA INSTALLATION (CM-36) 1. Determine a position and direction of installation and attach a camera bracket using double stick tape and screws. 2.
6 CABLE CONNECTION REAR-VIEW SYSTEM FOR VEHICLE [ CM-430 MONITOR ] CM-200 CM-36 OR Extension Cable (for Camera) CAMERA Extension Cable (for CAMERA) TRG Monitor Cable Extension Cable (for TRG) DC IN (12V~24V) Before making the connection, disconnect the ground terminal of the car battery to avoid short circuiting. The plug should be fully inserted into the connector, should be check pin arrangement before inserting. A loose connection may be caused mallfunction or problem of the unit.
7 SPECIFICATION REAR-VIEW SYSTEM FOR VEHICLE CM-430 (MONITOR) LCD size 4.3” Image ratio 16 : 9 Resolution 480 x 3(RGB) x 272 Brightness 400cd Contrast range 600 : 1 Active area 95.04(W) x 53.86(H) mm Viewing angle 80(L) / 80(R) / 65(T) / 52(B) Input System NTSC/PAL Input Video signal Composite Video (CVBS) 75Ω 1Vp-p Audio signal MONO Operating voltage Power Current consumption Speaker DC 12V - 24V 200mA Max. 0.
CM-200 (CAMERA) Image sensor 1/3” 960H color CCD Viewing angle 168(D) / 125(H) Min. Illumination 0.1Lux (F=2.0) Resolution 700 TV Lines Operating voltage Operating temperature Dimension Weight DC12V / 90mA -30°C ~ 70°C 36.6(W) x 27(H) x 38.2(D) mm 80g (Body only) CM-36 (CAMERA) Image sensor 1/3” 960H color CCD Viewing angle 120(D) / 95(H) Min. Illumination 0.1Lux (F=2.
MEMO REAR-VIEW SYSTEM FOR VEHICLE 15
INSTRUCTION MANUAL
