Installation Instructions

ManualsBrandsCampbell Hausfeld ManualsPlumbing1/3 HP Cast Iron Submersible Sump Pump

SPECIFICATIONS

POWER SUPPLY REQUIREMENTS 120 V, 60 Hz

MOTOR Single Phase, Dielectric Oil Filled

HORSEPOWER

1/2 HP............ (50CHF)

1/3 HP ........... (33CHF)

CIRCUIT REQUIREMENTS 15 A (minimum)

DIMENSIONS

11-1/2 in. high x 9-3/4 in. base

ON LEVEL (FACTORY SET) Approximately 9 in.

OFF LEVEL (FACTORY SET)

Approximately 4 in.

600002W-009 E 1/20

Submersible Sump Pump

www.chpumps.com

Intended for Indoor Use Only

Please read and save these instructions. Read carefully before attempting to assemble, install,

operate or maintain the product described. Protect yourself and others by observing all safety

information. Failure to comply with instructions could result in personal injury and/or property

damage! Retain instructions for future reference.

Operating Instructions and Parts Manual Sumps

PERFORMANCE GAL/HR

Model HP

Discharge Head (Lift Distance)

0 ft 5 ft 10 ft 15 ft 20 ft

50CHF 1/2 5100 4500 3840 3060 2040

33CHF 1/3 4600 3810 3060 2220 1200

CONSTRUCTION

MOTOR HOUSING Coated Steel (50CHF, 33CHF)

VOLUTE Cast Iron

IMPELLER

Glass Reinforced Thermoplastic

SHAFT Steel

DISCHARGE

1-1/2 in. NPT

Summary of content (12 pages)

PAGE 1
Submersible Sump Pump Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.
PAGE 2
INSTALLATION MANUAL SUMP PUMP DESCRIPTION Sump pumps are automatic pumps used to remove ground water from sump pits. The most common application is for basement drainage to prevent flooding in residential buildings. These sumps are designed to pump clear water only. These pumps are not designed to be used with a portable generator. Installation of this pump outdoors, unprotected from the weather, may cause hazardous conditions and will void warranty.
PAGE 3
INSTALLATION MANUAL NEVER HANDLE A PUMP or motor with wet hands or when standing on a wet or damp floor while the pump is plugged into the power supply. NE JAMAIS MANIPULER UNE POMPE ou un moteur de pompe avec les mains mouillées ou debout dans l’eau ou sur une surface humide. RISK OF ELECTRIC SHOCK. This pump has not been investigated for use in swimming pool and marine areas. RISQUE DE CHOC ÉLECTRIQUE.
PAGE 4
INSTALLATION MANUAL DO NOT USE THIS PUMP IN MUD, SAND, CEMENT, OIL CHEMICALS, GREY WATER, OR ANY OTHER WATER THAT IS NOT CLEAR GROUND WATER. NE PAS UTILISER CETTE POMPE DANS LA BOUE, LE SABLE, LE CIMENT, LES PRODUITS CHIMIQUES À L’HUILE, DE L’EAU GRISÂTRE OU TOUTE AUTRE EAU QUI N’EST PAS DE L’EAU CLAIRE SOUTERRAINE. DO NOT USE SUMP PUMPS TO HANDLE RAW SEWAGE. NE PAS UTILISER DE POMPES DE PUISARD POUR POMPER LES EFFLUENTS.
PAGE 5
INSTALLATION MANUAL Vertical Submersible Sump 6. Install discharge plumbing according to local, regional and state codes. Rigid PVC pipe is required. Do not use flex hosing in a permanent application. 1 2 3 4 10 7. Install a check valve (required) to prevent back-flow. The Wayne check valve (62061-WYN1) may be positioned just above the basin to allow easy removal of the pump for cleaning and service. 8. Install a gate valve or ball valve if required by local, regional or state code.
PAGE 6
INSTALLATION MANUAL TROUBLESHOOTING WARNINGS ALWAYS DISCONNECT THE PUMP FROM POWER SUPPLY before installing, servicing or making any adjustments. TOUJOURS METTRE LA POMPE HORS TENSION avant de procéder à l’installation, à l’entretien ou à des réglages. 1. Submersible pump models have permanently lubricated bearings and require no additional lubrication. 2. Submersible pumps contain dielectric oil for cooling. Dielectric oil can be harmful to the environment.
PAGE 7
INSTALLATION MANUAL TROUBLESHOOTING CHART (CONTINUED) Symptoms Possible Cause(s) Suggested Remedies Pump trips GFCI 1. Bad GFCI 1. Contact an electrician to replace GFCI 2. Bad pump 2. Replace pump 1. Switch 1. Replace pump 2. Switch obstructions 2. Remove obstruction to ensure free motion of switch 3. Restricted discharge (obstruction in piping) 3. Remove obstruction from discharge piping 4. Excessive inflow or pump not properly sized for application 4.
PAGE 8
REPLACEMENT PARTS 1 REPAIR KITS 8 REF. NO.
PAGE 9
INSTALLATION MANUAL INSTALLATION MANUAL ADDRESS PARTS CORRESPONDENCE TO: CAMPBELL HAUSFELD 101 Production Drive Harrison, OH 45030 U.S.A. FOR REPLACEMENT PARTS OR CUSTOMER SUPPORT, CALL 1-800-237-0987 Please provide following information: - Model number - Serial number on cord tag (not to be removed) - Part description and number as shown in parts list Thank you for making Campbell Hausfeld a key part of your home maintenance program.
PAGE 10
NOTES 10
PAGE 11
NOTES www.chpumps.
PAGE 12