CC5MPX and CC5MPXWD Digital Network Cameras Revision: 3/12 C o p y r i g h t © 2 0 1 1 - 2 0 1 2 C a m p b e l l S c i e n t i f i c , I n c .
Warranty “PRODUCTS MANUFACTURED BY CAMPBELL SCIENTIFIC, INC. are warranted by Campbell Scientific, Inc. (“Campbell”) to be free from defects in materials and workmanship under normal use and service for twelve (12) months from date of shipment unless otherwise specified in the corresponding Campbell pricelist or product manual. Products not manufactured, but that are re-sold by Campbell, are warranted only to the limits extended by the original manufacturer.
Assistance Products may not be returned without prior authorization. The following contact information is for US and international customers residing in countries served by Campbell Scientific, Inc. directly. Affiliate companies handle repairs for customers within their territories. Please visit www.campbellsci.com to determine which Campbell Scientific company serves your country. To obtain a Returned Materials Authorization (RMA), contact CAMPBELL SCIENTIFIC, INC., phone (435) 227-9000.
CC5MPX Table of Contents PDF viewers: These page numbers refer to the printed version of this document. Use the PDF reader bookmarks tab for links to specific sections. 1. Introduction...............................................................1-1 2. Specifications............................................................2-1 3. Getting Started ..........................................................3-1 3.1 3.2 3.3 3.4 3.5 Factory Setup ...............................................................
CC5MPX Table of Contents 7.4 7.5 7.6 7.7 7.8 7.3.6 Update..................................................................................... 7-16 7.3.7 Events ..................................................................................... 7-17 Memory Card ................................................................................... 7-18 Video Settings .................................................................................. 7-21 Image Capture .......................................
CC5MPX Table of Contents 18. Installation .............................................................18-1 19. Maintenance ..........................................................19-1 19.1 19.2 19.3 19.4 Lithium Battery .............................................................................. 19-1 Window and Lens Cleaning ........................................................... 19-1 CC5MPX O-Rings ......................................................................... 19-2 CC5MPX Desiccant...
CC5MPX Table of Contents FIGURE 7-6. Ethernet Power Savings Settings.......................................... 7-6 FIGURE 7-7. FTP Server Settings.............................................................. 7-7 FIGURE 7-8. SMTP Server Settings .......................................................... 7-9 FIGURE 7-9. SNTP Server Settings ......................................................... 7-10 FIGURE 7-10. System Settings ................................................................
CC5MPX Table of Contents FIGURE 22-3. Network Configuration .................................................... 22-2 FIGURE B-1. CC5MPXWD Window Defroster........................................B-1 FIGURE B-2. CC5MPXWD Window Defroster with Lens Tube Installed ...................................................................................................B-2 List of Tables TABLE 3-1. CC5MPX Default Configuration ........................................... 3-1 TABLE 4-1.
CC5MPX Table of Contents vi
Section 1. Introduction FIGURE 1-1. CC5MPX Camera The CC5MPX and CC5MPXWD are essentially the same camera, except the CC5MPXWD includes a window defroster that removes light frost and icing from the camera’s window. A more detailed description of the defroster is provided in Appendix B. NOTE For readability purposes, CC5MPX will refer to both cameras throughout this document unless specified otherwise.
Section 1.
Section 2. Specifications CAUTION CC5MPXWD Heating Element Resistance: 18 Ohms Operating Power CC5MPX: CC5MPXWD: 9 to 30 Vdc 9 to 16 Vdc Operating the CC5MPXWD camera and defroster at voltages higher than 16 Vdc may damage the camera. Current Drain Operating (camera only): 250 mA maximum @ 12 Vdc Quiescent: ≤1 mA (off power mode) CC5MPXWD defroster on: 1.
Section 2. Specifications Communication Protocols: Communication Switched Power Output: Maximum Output Current: 750 mA RS-232 and RS-485: Max. BAUD Rate: 115.2 kbps Memory Card Interface Type: File System: File Type: Size: Secure Digital (SD) FAT32 JPEG (image), AVI (video) Verified up to 16GB Dimensions Length: Width: Weight: 2-2 Web page interface via web browser FTP Email PakBus (for Campbell Scientific Dataloggers) 220 mm (8.7 in); 229 mm (9.0 in) with special zoom lens 93 mm (3.7 in) 1.
Section 3. Getting Started Ensure that the pigtail end of the power cable is properly terminated (see Wiring, Section 4) before connecting the power cable connector to the camera. If the power supply has an on/off switch, it is also recommended to switch the power off before connecting the power connector to the camera. For the initial power up and set up of the camera, it is also useful to unscrew the protective cap that protects the push button and LED indicator. 3.
Section 3. Getting Started Prior to installing the camera in the field, download and install the appropriate VLC media player to the PC that will be interfacing with the CC5MPX. 3.3 ActiveX Controls in Internet Explorer Currently the CC5MPX is only fully supported using the Windows Internet Explorer browser. The web interface for the CC5MPX will require the use of ActiveX controls when using Internet Explorer.
Section 3. Getting Started FIGURE 3-2. Local Area Connection Highlight the Internet Protocol (TCP/IP) selection and click on Properties. FIGURE 3-3.
Section 3. Getting Started You should record the existing settings that are used on the computer to restore the connection back once the CC5MPX setup is completed. In the screen shown above, the computer is set to Obtain the IP address automatically which is quite common. At this point you will also want to disconnect your computer from the network and connect it directly to the CC5MPX camera.
Section 3. Getting Started Click OK again here. Right click on the Local Area connection again and select repair. You should now be able to open your web browser and access the camera by typing http://192.168.1.90. In the above example, your computer was configured to 192.168.1.91 and the camera is set to at 192.168.1.90. Since you want to connect to the camera, the 192.168.1.90 is entered into the browser.
Section 3. Getting Started FIGURE 3-5. Web Interface Live Video Home Page If you select a video format to display from the Video Display Size drop down box, you should be prompted to install an Active X control. Your browser may be configured by default to block pop-ups. You will need to enable the pop up for the camera. 3.
Section 3. Getting Started The Device Configuration Utility can now be invoked. Select the CC5MPX as the device type and the appropriate COM port. Once the appropriate selections are made, click the connect button. FIGURE 3-6. CC5MPX Shown in Device Configuration Utility The camera has a large number of variable information so it may take about 30 seconds for this process to complete.
Section 3. Getting Started FIGURE 3-7.
Section 4. Cables/Wiring 4.1 Power and I/O Cable Connections The wiring for the CC5MPXCBL1-L Power and I/O Cable is as shown in TABLE 4-1 and FIGURE 4-1 through FIGURE 4-4. NOTE It is essential that the Ground cable be connected first when wiring the camera to the datalogger or the power supply. TABLE 4-1.
Section 4. Cables/Wiring TABLE 4-2. CC5MPXCBL1-L Power and I/O Cable Wire Usage Wire Color Function Connection Required When not Used Black Power Ground Always Red Input Power Always Green RS-232 TX (Output) or RS-485 A Green wire only needs to be connected when RS-232 or RS-485 communications are used with PakBus or the Device Configuration Utility.
Section 4. Cables/Wiring CC5MPXCBL1 Wire Color Connection Black CR1000 Power G Red CR1000 12V Green CR1000 C2 White CR1000 C1 Yellow Gray Terminal Block Blue Gray Terminal Block Clear CR1000 G FIGURE 4-1. Camera Connected to CR1000 CC5MPXCBL1 Wire Color Connection Black CR1000 Power G Red CR1000 12V Green CR1000 C2 White CR1000 C1 Yellow Gray Terminal Block Blue CR1000 C4 Clear CR1000 G FIGURE 4-2.
Section 4. Cables/Wiring CC5MPXCBL1 Wire Color Connection Black PS100 G Red PS100 +12V Green Gray Terminal Block White PS100 G Yellow Gray Terminal Block Blue Gray Terminal Block Clear PS100 G FIGURE 4-3. Camera wired for stand-alone operation without datalogger. For example, network connection only. CC5MPXCBL1 Wire Color Connection Black CR1000 Power G Red CR1000 12V Green MD485 A White MD485 B Yellow Gray Terminal Block Blue Gray Terminal Block Clear MD485 G FIGURE 4-4.
Section 4. Cables/Wiring 4.2 CC5MPXCBL1-L Power and I/O Cable Details The CC5MPXCBL1 cable has an outdoor environmentally rated screw type connector on one end and discrete wire pigtails on the other end that allow for flexible termination. When connecting the cable to the camera, the notch positions should always be lined up and care should be taken to not cross thread the connector.
Section 4.
Section 5. Camera Hardware Description Remove cap to connect Ethernet cable (typically the CC5MPXCBL2) Remove cap to press Setup button or view Status LED Connector for the CC5MPXCBL1 Power I/O Cable FIGURE 5-1. CC5MPX Connector Layout 5.1 Ethernet RJ-45 Connection The RJ45 connector on the camera is meant to interface the CC5MPX with either a network router, cellular modem, or directly to a laptop.
Section 5. Camera Hardware Description If a permanent Ethernet connection is required outdoors or if a connection is required in wet or harsh locations, the CC5MPXCBL2-L Environmentally Rated Ethernet cable must be used. The maximum cable length for the Ethernet cable is 70 m (230 ft). NOTE The CC5MPX does not support the PakBus communication protocol over Ethernet. 5.2 Power I/O Connection The CC5MPXCBL1 cable must be attached to the Power I/O connector for camera operation.
Section 5. Camera Hardware Description TABLE 5-1. Setup Button LED Indicator LED CC5MPX State Other Continuously Off No power or the camera is in one of the following low powered modes: Pressing the Setup button will force the camera to exit any of the low powered modes and remain fully on for a period of 5 minutes with the LED rapidly flashing.
Section 5. Camera Hardware Description 5.4 SD Memory Card The camera is internally equipped to use an SD memory card, which is available as an option for the CC5MPX. If you choose to use your own memory card, the memory card will need to be formatted with a PC using the FAT32 format. Image files can be stored on the SD memory card as JPEG files and video files are stored as AVI files. Individual image and video files are uniquely named with a sequence number, or with a date and time stamp.
Section 5. Camera Hardware Description SD Card Slot SD Card FIGURE 5-2. SD Card Insertion (wires not shown) 5.4.2 FTP Image Collection from the Memory Card If the camera is setup to store images to the memory card, it may be necessary to collect all the images from the memory card. The web interface does provide a user friendly method of viewing and saving select files from the memory card.
Section 5. Camera Hardware Description FIGURE 5-3. Image Collection from Installed SD Card 5.5 Switched Power Output The intended purpose of the switched power output is to control the power for a communication device. One common application is to have the camera control the power to a communication modem at a solar-powered site. Refer to Section 7.3.5 for details on configuring the switched power output via the web interface.
Section 6. Camera Configuration There are two methods for a user to configure the CC5MPX camera. The first is by using the web interface of the camera. This is the best way to set up a camera. Normally most users will need to communicate with the camera via the Ethernet connection in order to facilitate focusing and targeting of the camera when installed.
Section 6.
Section 7. Camera Operation Using Web Browser Interface The web interface allows the user to: • Fully configure the CC5MPX as required. • View information, system status, date and time. • View live video for the purpose of targeting and focusing the camera. The camera ships with the default static IP address of 192.168.1.90 and a Network Mask of 255.255.255.0. It is highly recommended to keep track of any changes made to the network settings.
Section 7. Camera Operation Using Web Browser Interface Some general items to remember about the web interface are as follows: • The home page of the camera is the Live Video page. There are no operational settings to change on the Live Video page. • If any settings are changed or added on any of the other pages, then the Submit button must be keyed to accept the changes. If the submit button is not keyed the changes will not be saved. 7.
Section 7. Camera Operation Using Web Browser Interface removed from a camera that is actively collecting and storing images or video. It will completely shut down for a period of 10 minutes and ensure the memory card is not corrupted. An alternate way of shutting down the camera is to hold the Setup Button down for a period of at least 10 seconds. Information features on the Live Video page include: • • Motion Detect Indicator o Turns from green to red when motion is detected.
Section 7. Camera Operation Using Web Browser Interface For example if you change the IP address of the camera, the changes will be accepted by clicking on the submit button and the new IP address will be in effect. FIGURE 7-3. Network Configuration Warning Page Tabs Sub Tabs FIGURE 7-4. Network Configuration Page The Network page displayed in FIGURE 7-4 allows the user to configure settings that are related to the CC5MPX network connectivity.
Section 7. Camera Operation Using Web Browser Interface 7.2.1 Network Settings The most common network settings are displayed first in the Network sub tab. These settings are summarized in the following table. TABLE 7-1. Network Settings Configuration Setting Description Default Value DHCP Enables DHCP operation of the network interface. Operates as a Static IP address if Disabled. Disabled Network IP Address Only set if DHCP is Disabled 192.168.1.
Section 7. Camera Operation Using Web Browser Interface • Full Power Save This power mode should be used if the lowest power consumption is desired and incoming Ethernet communications are not required. FIGURE 7-6. Ethernet Power Savings Settings The specific behavior of the camera’s Ethernet Power save is also influenced by the Power Mode of the camera. TABLE 7-2 will help to outline the Ethernet Power saving features versus various Power Modes of the camera. TABLE 7-2.
Section 7. Camera Operation Using Web Browser Interface • • • Full Power Save Mode • • • Always On Deep Sleep • Moderate Power Save Mode Full Power Save Mode • Not recommended • The Deep Sleep power consumption(6mA typical) is not affected by the Ethernet Power Mode If Ethernet communications are not used this can reduce the power consumption of the camera by 50 mA when the camera exits the deep sleep state.
Section 7. Camera Operation Using Web Browser Interface These settings configure the CC5MPX to be able to act as an FTP client to send image files to an FTP server. There are settings for two different servers. These settings simply configure the parameters that the camera will use to connect to the server. The FTP transfers must be enabled in the Image Capture menus. The CC5MPX can also act as an FTP server to enable images and video to be transferred from the memory card.
Section 7. Camera Operation Using Web Browser Interface FIGURE 7-8. SMTP Server Settings 7.2.5 SNTP (TIME) Server Setting Clicking on the SNTP Server sub tab will display the SNTP (TIME) Server settings (see FIGURE 7-9). The configuration of an SNTP server will provide a means of synchronizing the onboard clock of the CC5MPX with the specified SNTP server. This will ensure that the camera clock is always accurate. It is also possible to configure a time zone offset for the camera.
Section 7. Camera Operation Using Web Browser Interface FIGURE 7-9. SNTP Server Settings 7.3 System Configuration Selecting the System tab will activate the System Settings page (see FIGURE 7-10). The main System settings page has 7 Sub Tabs as follows: • Date and Time • Automatic Date and Time Update • Site Name • Users/Security • Digital I/O • Update • Events FIGURE 7-10.
Section 7. Camera Operation Using Web Browser Interface 7.3.1 System Date and Time The Date and Time sub menu (see FIGURE 7-11) provides a means for viewing and setting the current Date and Time of the camera. The available options include: • Setting the Time Manually To set the date and time manually select the Set Manually button and then select the date and time values from the drop down boxes. You must click on the Submit button for the settings to take effect.
Section 7. Camera Operation Using Web Browser Interface 7.3.2 Automatic Date and Time Update The Automatic Date and Time sub menu (see FIGURE 7-11) configures the camera for automatic date and time updates. The setting parameters are as follows: • Time Variance in Seconds to Perform clock update Select the minimum allowable variance that will result in the camera’s time being changed. • Source Select one of 3 options for the Automatic Time updates.
Section 7. Camera Operation Using Web Browser Interface FIGURE 7-13. Site Name Site Name FIGURE 7-14. Location of Site Name 7.3.4 Users and Security The Users/Security sub menu (see FIGURE 7-15) allows the setting of security features in the CC5MPX. By default, the cameras are shipped with the security Authentication disabled. When the Authentication setting is set to Enable, users will be prompted for a User Name and Password before access is given.
Section 7. Camera Operation Using Web Browser Interface the camera saves the action, the user list will show the user name and their authority level. The user name and password must both be 4 to 32 characters in length. Authority Level Access: • • • Admin o Full camera access o Can create and edit users and disable security Operator o Full camera access o Only restrictions are Security Settings Viewer o Only access to the Live Vide (home page) and the Memory Card Page is given.
Section 7. Camera Operation Using Web Browser Interface 7.3.5 Digital I/O Settings The Digital I/O sub menu (see FIGURE 7-16) allows the configuration of some of the camera’s I/O signals. FIGURE 7-16. Digital I/O Settings 7.3.5.1 External Trigger Input Settings The external Trigger Input can be configured to Active High or Active Low. When set to Active High, 0 volts will be the inactive state and a positive voltage will be the active state.
Section 7. Camera Operation Using Web Browser Interface 7.3.5.4 CC5MPXWD Heater Power Control The Heater Power Control settings control the operation of the CC5MPXWD window defroster. If enabled, the camera will only turn on the heater if the CC5MPXWD’s internal temperature is below the threshold setting. The temperature threshold values are limited to -40°C to +25°C.
Section 7. Camera Operation Using Web Browser Interface FIGURE 7-17. Update Menu 7.3.7 Events The Events sub menu (see FIGURE 7-18) provides a list of system events. If the System Status box is red in the Live Video page, the details are logged in the Events Log. One of the most common recorded events is the indication that a memory card is properly present after a power up. The message confirms that the memory card is functioning and it also indicates the size of the memory card.
Section 7. Camera Operation Using Web Browser Interface FIGURE 7-18. Event Logs 7.4 Memory Card Selecting the Memory Card tab will bring up the Memory Card page (see FIGURE 7-19) and allow access to the internal SD Card. FIGURE 7-19. Memory Card Page You will need to click on SDCARD #1. If there is no memory card installed, the camera a page will come up saying that the SD Card is not present. Otherwise you will see the root directory of the Memory cards (see FIGURE 7-20).
Section 7. Camera Operation Using Web Browser Interface FIGURE 7-20. Memory Card Directory Listing There are a possibility of nine main directories that are created for image and video storage on the Camera. There is a still image and video directory for each type of capture methods and a directory for manually captured stills. A directory will not be created by the camera if the capture method is not used.
Section 7. Camera Operation Using Web Browser Interface • SelfTimed1Video • SelfTimed2Still • SelfTimed2Video Clicking on one of the main folders will display the contents inside of that folder. Normally another set of sub folders will be displayed. The camera creates sub folders that are named by date. The date sub folders can be configured to store images in folders named either by Year_Month or Year_Month_Day (see FIGURE 7-21). FIGURE 7-21.
Section 7. Camera Operation Using Web Browser Interface The web interface will display up to 200 files per page. If more files are in the directory, select “page T” to view the additional files (see FIGURE 7-23). FIGURE 7-23. Example of Multiple Page Viewing The web interface provides a method of viewing or deleting images and video from the memory card. It is possible to delete either complete or portions of Directories or Subfolders as well as individual images or videos.
Section 7. Camera Operation Using Web Browser Interface The Video Settings consist of the following parameters: • Position Banner 3 options available are: o OFF o Inside Top o Inside Bottom FIGURE 7-25. Video Banner Inside Top with Time Stamp and Text • Name on Image Banner If YES is selected, text can by typed in which would appear in the video banner. • Include Timestamp in Banner The options are NONE or the Time Stamp format of YYYY/MM/DD HH:MM:SS.
Section 7. Camera Operation Using Web Browser Interface o Number Increment A unique number is appended to each file name. When the Number Increment is selected an additional box will allow a starting number to be entered. An example of a file name with the count type is: Video1_0000001994.avi o Date and Time Each file name will have a time stamp appended to it. An example of a file name with the Date and Time option is: Video1_2011_01_28_14_22_10.avi Video1_YYYY_MM_DD_HH_MM_SS.
Section 7. Camera Operation Using Web Browser Interface • External Trigger • Motion Detection FIGURE 7-26. Image Capture Page 7.6.1 Power Modes The Power Modes sub tab (see FIGURE 7-27) allows the selection of the type of power management that will be used. FIGURE 7-27.
Section 7. Camera Operation Using Web Browser Interface One of the main factors in determining which power mode to use is the power consumption budget that is available for the camera. If the camera is operating from an AC main power supply, then the camera will have the best performance characteristics in the Fully On State. On the other hand if the camera needs to operate from a battery for long periods of time, then the OFF state will be more suitable.
Section 7. Camera Operation Using Web Browser Interface • Always On Deep Sleep • Moderate Power Save Mode Full Power Save Mode • Not recommended • The Deep Sleep power consumption(6mA typical) is not affected by the Ethernet Power Mode If Ethernet communications are not used this can reduce the power consumption of the camera by 50 mA when the camera exits the deep sleep state.
Section 7. Camera Operation Using Web Browser Interface 7.6.2 Self Timed Capture1 The Self Timed Capture1 sub tab (see FIGURE 7-28) is used to configure the camera to capture still images or video by using the internal clock of the CC5MPX. FIGURE 7-28. Self-Timed Capture Page When either of the Self Timed Capture triggers is enabled, the CC5MPX uses its internal clock as a trigger to initiate the capture of still images or video.
Section 7. Camera Operation Using Web Browser Interface The first step in setting up the Self Timed Capture is to select the Enable option for the capture method (see FIGURE 7-29). Once Enable is selected, parameters for the capture method can be edited. FIGURE 7-29. Enable and Capture Time Values The Self Timed Capture triggers are set up with the timing relative to midnight. The first parameter to enter is the Start Minutes relative to midnight.
Section 7. Camera Operation Using Web Browser Interface TABLE 7-6.
Section 7. Camera Operation Using Web Browser Interface The Capture Interval is the time between capture events once the Start Minutes value is reached. For hourly pictures a value of 60 can be entered. If a value of 0 is entered, (not recommended) the Image Interval time will apply to still images and video of the specified duration will be captured repeatedly. The following table summarizes all the parameters associated with the Self Timed Capture. TABLE 7-7.
Section 7. Camera Operation Using Web Browser Interface Send via FTP FTP Still Image Settings Send via PakBus PakBus Still Image Settings Video Capture Video Settings Duration In Seconds Capture To Memory Card • • • • • Disabled FTP Settings#1 FTP Settings#2 Settings #1 Settings #2 • • Disabled Enabled • • • • • • Settings #1 Settings #2 Yes No Settings #1 Settings #2 One of two video settings can be used for the video capture. The length of time the video is recorded for.
Section 7. Camera Operation Using Web Browser Interface 7.6.3 Self Timed Capture2 Refer to the previous section as the settings and parameters are the same. 7.6.4 External Trigger The External Trigger sub tab (see FIGURE 7-30) is used to configure the camera to capture still images or video by using an external signal that is applied to the External Trigger input line. The External Trigger can be configured for an active HIGH signal or an active LOW signal (see Digital I/O Settings).
Section 7. Camera Operation Using Web Browser Interface FIGURE 7-30.
Section 7. Camera Operation Using Web Browser Interface TABLE 7-8.
Section 7. Camera Operation Using Web Browser Interface Video Capture Video Settings Duration In Seconds Capture To Memory Card • • • • Yes No Settings #1 Settings #2 The length of time the video is recorded for. • • Selecting CARD will enable the video taken to be stored to the memory card. This is the allowable space on the memory card that will be reserved for videos taken by this External Trigger Capture. The value is in Megabytes. A value of 1000 will reserve 1000 Mbytes.
Section 7. Camera Operation Using Web Browser Interface FIGURE 7-31.
Section 7. Camera Operation Using Web Browser Interface TABLE 7-9. Motion Detection Settings Variable Allowable Values Sensitivity Level 1 to 99 Description The best method for determining where to set the level for your needs is to experiment with the values. The Value of 1 is the least sensitive value but less prone to false triggers. The value of 99 is the most sensitive value and is most susceptible to false triggers. You do not need to enable the motion detection to test its functionality.
Section 7.
Section 7. Camera Operation Using Web Browser Interface 7.7 PakBus Communication Settings FIGURE 7-32. Communication Settings Page Communications using the PakBus protocol can enable remote retrieval and/or storage of images or video to external devices such as compatible Campbell Scientific dataloggers. The factory default communication interface is RS-232. If RS-485 is required the internal camera jumpers will need to be changed. See Section 8 Internal Jumpers for more details. TABLE 7-10.
Section 7. Camera Operation Using Web Browser Interface 7.8 Still Image Settings Selecting the Still Image Settings tab will bring up the Still Image Settings page (see FIGURE 7-33). The Still Image Settings allows the configuration of the still images that the camera will take. There are two sub tabs that include two independent still settings: • Still Settings #1 • Still Settings #2 TABLE 7-11 describes the variables used in the Still Images Settings. FIGURE 7-33.
Section 7. Camera Operation Using Web Browser Interface TABLE 7-11.
Section 7. Camera Operation Using Web Browser Interface TABLE 7-12.
Section 8. Internal Jumpers There are two sets of jumpers that are internal to the camera. One set of jumpers is used to select either RS-232 or RS-485 communications on the Power I/O cable. The other jumper set is used to select a pull up or a pull down resistor on the External Trigger input line. Refer to Section 20 Backplate Removal Procedures for details to remove the backplate to access the internal jumpers of the camera. 8.1 RS-232 / RS-485 Jumpers The jumper locations are shown in FIGURE 8-1.
Section 8. Internal Jumpers 8.2 External Trigger Pull-Up/Pull-Down Jumper The jumper location for the External Trigger Pull-up/Pull-down location is shown in FIGURE 8-1. When the jumper is located on the right two pins of the header (factory default position), there is a 100 kohm pull-down resistor connected from the External Trigger line to ground. When the jumper is placed on the left two pins of the header, there is a 47 kohm pull-up resistor connected from the External Trigger line to 3.3 Volts.
Section 9. RS-232 Communications The RS-232 serial communications are used with the camera for two purposes. One is to configure and setup the camera using the Device Configuration Utility software that Campbell Scientific provides. The other purpose is to send image files from the camera to other devices using the PakBus protocol. Check the PakBus Port value under the Communication Settings if you are not sure that your camera has its internal jumpers configured to RS-232 or RS-485 (see FIGURE 9-1).
Section 9. RS-232 Communications FIGURE 9-2. Connecting the CC5MPX to a 9-Pin RS-232 Port An illustration of the required RS-232 connections to a datalogger is shown in FIGURE 9-3. FIGURE 9-3.
Section 10. RS-485 Communications The optional RS-485 communication interface of the CC5MPX can be used in conjunction with the MD485 to interface a datalogger to one or more cameras. Refer to the MD485 manual for additional information. The MD485 is useful for connecting more than one camera to a datalogger or if long cable lengths are involved.
Section 10.
Section 11. PakBus Communications The camera uses the PakBus protocol to send image files from the camera to the datalogger or other PakBus compatible devices. When an image or video file is ready to be transmitted, the camera will initiate communications and send the image or video via the selected serial interface. The CC5MPX is capable of producing video files that exceed 30 MB in size. Trying to send such a large file to a datalogger using PakBus can be problematic.
Section 11.
Section 12. Device Configuration Utility The Device Configuration Utility can be used to change settings in the CC5MPX. The Device Configuration Utility software can be downloaded, at no charge, from the Campbell Scientific website. Using the Device Configuration Utility • Connect the camera to the serial port of a PC using the DB9M-TERM as shown in Section 9, RS-232 Communications. The A200 Sensor to PC Interface can be used in lieu of the DB9M-TERM.
Section 12. Device Configuration Utility FIGURE 12-2.
Section 13. Image Quality Lighting conditions have the greatest influence on image quality. The CC5MPX camera produces the best images under normal daylight conditions. Pictures taken in good daylight conditions produce crisper and brighter images, as the camera uses the entire image to adjust the exposure settings of a scene. Scenes that contain small variations in light intensities will produce better images.
Section 13.
Section 14. Lens The standard Lens for the CC5MPX camera contains the following features: • C-Type Mount • Varifocal (manual zoom) • Manual Focus • DC Iris Access to the lens for adjusting the zoom and focus requires the removal of the CC5MPX lens tube (see FIGURE 14-1). The lens tube is threaded on and needs to be turned counter clockwise to be removed. The zoom and focus adjustments are shown in FIGURE 14-2. The thumbscrews may need to be loosened prior to moving the adjustments.
Section 14. Lens Zoom Focus FIGURE 14-2. Focus and Zoom Adjustments 14.1 Camera Lens and Field of View The CC5MPX camera includes a 4 to 12 mm lens, which provides an approximate 27° horizontal field of view when fully zoomed in and an 80° horizontal field of view when fully zoomed out. The CC5MPX with the special-ordered zoom lens will have a 10 to 40 mm lens, which provides an approximate 9° horizontal field of view when fully zoomed in and a 35° horizontal field of view zoomed out.
Section 14. Lens 14.2 Focus and Zoom Adjustment To facilitate the focus and zoom adjustments, a network connection will need to be established with the camera to view the live video on a web browser. Refer to Sections 3 and 7 for details on accessing the camera with a web browser. If the LED is not flashing while the camera is wired up and the power is turned on, you may need to press the setup button to wake the camera from any of its low powered modes.
Section 14. Lens There may be instances where the focusing numbers cannot be used to focus the CC5MPX. One such scene may be where a nearby object is desired to be in focus and the background may be out of focus. However, for most “scene” images where nearby objects and far objects are not involved, the focusing numbers work well. FIGURE 14-4. Homepage Video Display and Focusing Numbers 14.3 Temperature Variations and Focus The CC5MPX can operate under extreme temperature variations.
Section 15. Power Calculations and Timings The CC5MPX was specifically designed for operation in power-constrained systems such as solar powered sites. It is critical in such systems that the camera be properly configured to meet the constraints of the intended application. This section outlines the power consumption of the camera for purposes of power supply design for a system. 15.1 Standalone Operation In standalone mode the camera operates as a self-contained image and video logger.
Section 15. Power Calculations and Timings 15.2 Operation with Communications The power calculations are more complicated when communications are involved, as the amount of time the camera is in the Fully On active state is increased by the amount of time it takes for the camera to transfer an image or video. The transfer times are influenced by two main factors: the size of the image and the transfer speed used to send the image.
Section 15. Power Calculations and Timings • Determine the power consumed by the quiescent state in Amp-hours. Quiescent Power = quiescent minutes * quiescent current draw/60 Quiescent Power = 1418 minutes*6 mA/60 = 141.8 mA-hour or 0.1418 Amp-hours/day • Determine the power consumed by the active state in Amp-hours. Active Power = active minutes * active current draw/60 Active Power = 22 minutes*250 mA/60 = 91.67 mA-hour or 0.
Section 15.
Section 16. CR1000 Interface Guide This section contains information for interfacing the CC5MPX camera to the CR1000 datalogger. The CC5MPX can interface to the CR1000 by using RS232 default or RS-485. The RS-232 configuration is the simplest option as it does not require an additional hardware interface. The pigtail end of the CC5MPXCBL1 Power and I/O Cable can be terminated directly to the CR1000 wiring panel control ports (COM 1 to 4). Refer to Section RS-232 Communications for wiring details.
Section 16. CR1000 Interface Guide • DDD – Is the destination drive on the CR1000 o USR for the user drive o CRD for the compact flash memory card • NAME – Is any name string that will be used to name the files • EXT – The file extension of the incoming file must match. In the case of the camera this must always be either “JPG” or “AVI”. • NNNN – The number of files kept in the ring memory.
Section 17. Remote Image Retrieval Once the camera has transferred an image or video to a datalogger, existing LoggerNet communications can be used to retrieve images and video remotely from the datalogger memory. 17.1 LoggerNet File Retrieval LoggerNet (Version 4.0 or newer) includes the File Retrieval setup that facilitates the image and video file retrieval from PakBus dataloggers (CR800 series, CR1000, and CR3000).
Section 17. Remote Image Retrieval default the .jpg and .avi names are a wild card (*), which means all .jpg or .avi files in the specified directory will be retrieved. If you have used specific filenames in the camera configuration you are able to specify these names in the Edit File Pattern parameter. It is possible to configure multiple File Patterns to collect images or video on different schedules or from multiple directories.
Section 17. Remote Image Retrieval In dataloggers such as the CR1000, the Device Map can include the CPU, USR and the CRD (compact flash module). The devices show up in the left hand side of the File Control panel. To view files of a certain device, simply click on the desired device listed in the panel (FIGURE 17-3). Use the “Retrieve” button to download the image from the datalogger. FIGURE 17-3.
Section 17.
Section 18. Installation The camera enclosure is designed to be environmentally sealed for outdoor installations. The enclosure provides protection from moisture or high humidity. It is not intended for operation under water. All that is required for use is an appropriate mounting fixture. FIGURE 18-1. CC5MPX Mounting Kit The camera is equipped with a set of three ¼-20 threaded mounting holes (see FIGURE 18-2). These mounting holes are centered along the bottom of the camera and are spaced 1.0 in. (25.
Section 18. Installation The 18549 Mounting Kit is available for mounting the camera to a crossarm, tripod, or pole. When using this mounting kit, align the outer holes of the CC5MPX with the center hole and the 180° slot of the mount. Loosely secure the two together with the two ¼-20 x 0.5 in. Hex bolts included with the kit. It is now possible to mount the CC5MPX to either a crossarm or other mounting surface with the included u-bolt.
Section 19. Maintenance The CC5MPX requires little maintenance and no calibrations. Keeping the camera clean is important for the longevity of the camera and image and video quality. 19.1 Lithium Battery The camera is equipped with a lithium-thionyl-chloride battery. The battery maintains the clock functionality for periods when power is not connected to the camera. The expected battery life is 10 years. It is recommended that the battery be replaced by a certified repair facility.
Section 19. Maintenance 19.3 CC5MPX O-Rings There are three O-rings that should be inspected on the camera. If any of the O-rings look cracked or damaged, then they will require replacement. The locations of the three O-rings are shown in FIGURE 19-2 through FIGURE 19-4. Backplate O-ring FIGURE 19-2. Backplate O-ring Button Cap O-ring FIGURE 19-3.
Section 19. Maintenance Front Main Body O-ring FIGURE 19-4. Front Main Body O-ring It is recommended that the O-rings be inspected whenever opened or at a minimum of every two years (with desiccant replacement) to ensure that the seal integrity is maintained. Contact Campbell Scientific for details on replacement parts. It is important to note that the button cap O-ring and the front main body Oring are both glued into place to prevent the O-rings from inadvertently falling out.
Section 19. Maintenance Location of Desiccant FIGURE 19-5.
Section 20. Backplate Removal Procedures It will be necessary to remove the backplate for the following reasons: • Access to the SD memory card • Change Internal Jumper Positions • Replace Desiccant • Inspect O-rings If the camera is powered up and operating (LED is flashing), properly shutdown the camera by holding down the setup button for more than 10 seconds continuously. Alternatively the Shutdown button can be used from the Live Video Home page of the camera.
Section 20. Backplate Removal Procedures Screw Screw Screw with Chain and Washer Screw with Chain and Washer Screw Screw FIGURE 20-1. Backplate View After the screws are removed, gently pull the backplate out (see FIGURE 20-2). The backplate will still be attached to the camera with the wires (see FIGURE 20-3). Do not remove the wires. Pivot the backplate to the left side of the camera. You will now have access to the inside of the camera.
Section 20. Backplate Removal Procedures Plastic washer is under tether chain Screw Philip Screw FIGURE 20-2. Removing Backplate Screws (wires not shown) Wires O-ring FIGURE 20-3.
Section 20. Backplate Removal Procedures The backplate can only be seated in the orientation that aligns the flat surfaces of the backplate and the bottom of the camera body. This will also help align the screw holes. The six screws can now be threaded and hand tightened. Be sure the two plastic washers are located between the tether chains and the backplate.
Section 21. System Limitations This section outlines some system limitations that exist in the CC5MPX camera 21.1 High resolution 5 Megapixel Images The capturing of 5 MP pictures will result in longer capture times than other image resolutions. When a 5 MP image is captured the continuous video stream is paused, the image sensor is reconfigured and then the 5 MP image is captured. This longer delay time would be noticeable when capturing images from the external trigger.
Section 21.
Section 22. Internal USB Function The internal USB port in the camera currently only has one function. It provides a backdoor for setting up the Network interface on the camera. When first connected to a PC the following window will pop up: FIGURE 22-1. USB Network Interface Select the option Open folder to view files.
Section 22. Internal USB Function FIGURE 22-2. CC5MPX USB Directory Run the executable file usbconf.exe. FIGURE 22-3. Network Configuration At this point you can confirm or edit the IP address settings. If changes are made, the apply button must be selected followed by Exit. Do not unplug the USB cable or shut down the camera at this point. The USB device must be safely removed before unplugging the cable or shutting down the camera otherwise the changes will be lost.
Section 23. Quick Notes 23.1 CC5MPX General • The LED will Flash or be on when the camera is in an Active Power State. • When the LED is steadily on the camera is booting up. Avoid interrupting this process. • Briefly pressing the setup button will always cause the camera to exit from any low powered quiescent states and enable the Ethernet interface for communications. The camera will remain in this state for 5 minutes.
Section 23. Quick Notes 23.2 Campbell Datalogger Users • If interfacing to a datalogger, ensure that your datalogger has the appropriate PakBus operating system. • Use either the CC5MPX built in web interface or the Device Configuration Utility to change settings in the camera. • Use the Device Configuration Utility to change settings in MD485 or other PakBus devices. • The Device Configuration Utility can also be used to set the Dataloggers memory and PakBus parameters.
Section 23. Quick Notes TABLE 23-1. Power Mode Summary Power Mode Fully On Partially On Deep Sleep Off State Ethernet Power Save Mode Always On Full Power Save Mode Always On Full Power Save Mode Always On Full Power Save Mode Always On Full Power Save Mode 3. 4. Quiescent Current Draw Max.
Section 23.
Appendix A.
Appendix A.
Appendix A.
Appendix A.
Appendix B. CC5MPXWD Window Defroster Description The window defroster consists of an aluminum ring with a resistive type heating element (see Figure B-1 CC5MPXWD Window Defroster). The camera can be programmed to turn on the power to the heater based on the internal temperature reading of the camera. The on duration can also be set on the camera. The heating element is nominally 18 Ohms in resistance. The current draw will vary with the allowable input voltage range of 9 to 16 VDC.
Appendix B. CC5MPXWD Window Defroster Description FIGURE B-2.
Campbell Scientific Companies Campbell Scientific, Inc. (CSI) 815 West 1800 North Logan, Utah 84321 UNITED STATES www.campbellsci.com • info@campbellsci.com Campbell Scientific Africa Pty. Ltd. (CSAf) PO Box 2450 Somerset West 7129 SOUTH AFRICA www.csafrica.co.za • cleroux@csafrica.co.za Campbell Scientific Australia Pty. Ltd. (CSA) PO Box 8108 Garbutt Post Shop QLD 4814 AUSTRALIA www.campbellsci.com.au • info@campbellsci.com.au Campbell Scientific do Brazil Ltda.
