INSTRUCTION MANUAL CD100 Mountable Display with Keypad Revision: 1/14 C o p y r i g h t © 2 0 1 1 - 2 0 1 4 C a m p b e l l S c i e n t i f i c , I n c .
Warranty “PRODUCTS MANUFACTURED BY CAMPBELL SCIENTIFIC, INC. are warranted by Campbell Scientific, Inc. (“Campbell”) to be free from defects in materials and workmanship under normal use and service for twelve (12) months from date of shipment unless otherwise specified in the corresponding Campbell pricelist or product manual. Products not manufactured, but that are re-sold by Campbell, are warranted only to the limits extended by the original manufacturer.
Assistance Products may not be returned without prior authorization. The following contact information is for US and international customers residing in countries served by Campbell Scientific, Inc. directly. Affiliate companies handle repairs for customers within their territories. Please visit www.campbellsci.com to determine which Campbell Scientific company serves your country. To obtain a Returned Materials Authorization (RMA), contact CAMPBELL SCIENTIFIC, INC., phone (435) 227-9000.
Table of Contents PDF viewers: These page numbers refer to the printed version of this document. Use the PDF reader bookmarks tab for links to specific sections. 1. Introduction ................................................................ 1 2. Cautionary Statements .............................................. 1 3. Quickstart ................................................................... 2 4. Overview ..................................................................... 2 5. Specifications.......
CD100 Mountable Display with Keypad 1. Introduction The CD100 is an easy-to-read panel-mountable datalogger data display. It includes a large-format keypad for input. The CD100 is compatible with several Campbell Scientific dataloggers. Refer to Section 5, Specifications, for a complete list. When properly installed, the CD100 is weather and dust resistant. As a purchased service, Campbell Scientific offers the option of installing the CD100 into an enclosure. 2.
CD100 Mountable Display with Keypad 3. Quickstart 1. If the CD100 is to be mounted into an enclosure bulkhead, refer to Section 6, Installation, for instructions. 2. Using an SC12 cable as shown in FIGURE 3-1, connect the 9-pin CS I/O port of a CR1000 or other compatible datalogger to the 9-pin CS I/O port on the back of the CD100. FIGURE 3-1. Connecting the CD100 to the CR1000 Datalogger 3. 4. Power the datalogger; the display should power up and be ready for use.
CD100 Mountable Display with Keypad 5. Specifications Features: • Operable with gloved hand • 16 key alpha numeric keypad • 8 line x 21 character display (64 x 128 pixel) Compatibility: CR800 (not CR850) CR1000 CR3000 Interface: CS I/O, SDC address 2 Temperature Operating: Storage: Transit: –45° to 85°C –50° to 85°C 1 hour at –60°C Power Requirement Source: Current Draw Inactive: Active: 0.
CD100 Mountable Display with Keypad 5. Before tightening screws, adjust the gasket to align it just inside the edges of the display. Uniformly tighten the screws, but do not over-tighten. Measurement Units = Inches Edge of Cut Edge of CD100 Image Not Actual Size FIGURE 6-1.
CD100 Mountable Display with Keypad FIGURE 6-2.
CD100 Mountable Display with Keypad 7. Operation An overview of keyboard functions is presented in TABLE 7-1, Keyboard Display Key Functions, and FIGURE 7-1, Display Menu Overview. Detailed descriptions are available in the datalogger manual. TABLE 7-1.
CD100 Mountable Display with Keypad FIGURE 7-1. Display Menu Overview 8. Maintenance Active desiccant must be maintained in the datalogger enclosure to avoid water damage to the display electronics, the datalogger, and other contents. No other maintenance is required. Depending on the environment and weather tightness of the installation, dust may accumulate between the surface window and the underlying display elements. If this occurs, return the display to Campbell Scientific for cleaning.
CD100 Mountable Display with Keypad 8
Campbell Scientific Companies Campbell Scientific, Inc. (CSI) 815 West 1800 North Logan, Utah 84321 UNITED STATES www.campbellsci.com • info@campbellsci.com Campbell Scientific Africa Pty. Ltd. (CSAf) PO Box 2450 Somerset West 7129 SOUTH AFRICA www.csafrica.co.za • cleroux@csafrica.co.za Campbell Scientific Australia Pty. Ltd. (CSA) PO Box 8108 Garbutt Post Shop QLD 4814 AUSTRALIA www.campbellsci.com.au • info@campbellsci.com.au Campbell Scientific do Brasil Ltda. (CSB) Rua Apinagés, nbr.