CM300 Series Mounting Poles 1/08 C o p y r i g h t © 2 0 0 8 C a m p b e l l S c i e n t i f i c , I n c .
Warranty and Assistance The CM300 SERIES MOUNTING POLES are warranted by CAMPBELL SCIENTIFIC, INC. to be free from defects in materials and workmanship under normal use and service for twelve (12) months from date of shipment unless specified otherwise. Batteries have no warranty. CAMPBELL SCIENTIFIC, INC.'s obligation under this warranty is limited to repairing or replacing (at CAMPBELL SCIENTIFIC, INC.'s option) defective products.
CM300 Series Table of Contents PDF viewers note: These page numbers refer to the printed version of this document. Use the Adobe Acrobat® bookmarks tab for links to specific sections. 1. General ..........................................................................1 2. Specifications ..............................................................2 3. Installation....................................................................2 3.1 3.2 3.3 3.4 3.5 Tools List..........................................
This is a blank page.
CM300 Series Mounting Poles 1. General The CM300 Series Mounting Poles provide a stainless steel 1.5 IPS vertical pole for mounting sensors, enclosures, or other instrumentation. Pole length is 23”, 47”, or 56” for the CM300, CM305, and CM310 models respectively. Mounting poles can be placed directly into a concrete foundation, attached to a concrete foundation with the Pedestal J-Bolt Kit option, or can be selfsupporting with the Pedestal Leg options (Figures 1-4).
CM300 Series Mounting Poles 2. Specifications Stainless Steel 1.5 IPS Pipe 1.
CM300 Series Mounting Poles Vinyl Cap CM300 Series Pole Concrete Foundation 24” 8” FGURE 2. CM310 Mounting Pole in Concrete Foundation 3.3 CM300 Series Mounting Pole with Pedestal J-Bolt Kit A CM300 series pole with the Pedestal J-Bolt Kit option can be used for permanent installations where there is a need to periodically plumb the pole. J-bolts are installed in a concrete foundation using the template provided with the kit. Construct a form 14” square (inside dimensions) from 2”x 4” lumber.
CM300 Series Mounting Poles Remove the template after the concrete has cured. Insert the pole into the pedestal, and tighten the six bolts evenly. Each J-bolt should have two nuts and one washer installed, with the bottom nuts about 1/4” above the bottom of the threads. Place the pedestal over the J-bolts and install a flat washer, split washer, and nut on each bolt – do not tighten the nuts at this time. Adjust the lower nuts on each J-bolt to plumb the pole.
CM300 Series Mounting Poles 3.4 CM300 Series Mounting Pole with Pedestal Legs A CM300 series pole with a Pedestal Leg option can be used for temporary installations or for applications where a concrete foundation is not an option. The “Short” Pedestal Legs are adequate for most applications. The “Long” Pedestal Legs provide additional stability for applications where the feet cannot be secured (e.g. to the surface of a roof), for extended poles, or for locations with high winds.
CM300 Series Mounting Poles 3.5 Grounding PN 19238 grounding kit may be used to provide an earth ground for the pedestal and associated instrumentation. Attach the earth and enclosure ground wires to the lug on the pedestal base as shown in Figure 4.
This is a blank page.
Campbell Scientific Companies Campbell Scientific, Inc. (CSI) 815 West 1800 North Logan, Utah 84321 UNITED STATES www.campbellsci.com info@campbellsci.com Campbell Scientific Africa Pty. Ltd. (CSAf) PO Box 2450 Somerset West 7129 SOUTH AFRICA www.csafrica.co.za cleroux@csafrica.co.za Campbell Scientific Australia Pty. Ltd. (CSA) PO Box 444 Thuringowa Central QLD 4812 AUSTRALIA www.campbellsci.com.au info@campbellsci.com.au Campbell Scientific do Brazil Ltda.
