Installation Guide

6. Note: Refer to the style of
assembly that matches the style of
your fixture.
If your fixture has shades,
STYLE #1A - Place shade on tube,
then install bulb.
STYLE #1B - Install bulb, shade
then finial.
STYLE #2 - Remove spinner nut
from socket. Position glass on lamp
and secure with spinner nut.
Note: Glass may face up or down.
Note: If your fixture has
candle-style lights, slide the tubes
over the uplight sockets
STYLE #3 - Install proper bulb type
and wattage before assembling
the glass. Remove ball screw from
the curved stem. Position glass on
lamp with the curved stem being
inserted through the hole in the
glass. Hand tighten the ball screw
to secure the glass in place.
7. If not already done, install
proper bulb type and wattage.
Note: If your product does not
have a bottom light, your fixture is
complete.
8. Attach the stem to the fixture.
9. Position the glass over the
stem. Secure the glass in place
using the fibre washer, hex nut,
decorative cap and finial.
SAFETY PRECAUTIONS:
INSTALLATION:
Glass
Fixture
Socket
Fixture
Stem
Finial
Cap
Decorative
Glass
C-2
05/12
Spinner
Nut
CHANDELIER
Glass
Hole
For Stem
Ball Screw
STYLE #2
STYLE #3
Fixture
Hex
Nut
Fibre
Washer
Questions or Concerns Contact Canarm At:
1-800-265-1833 (English) or 1-800-567-2513 (French) Monday Through Friday 8:00am - 5:00pm E.S.T.
STYLE #1A
STYLE #1B
Finial
Shade
Bulb
Tube
Shade
Tube
Bulb
L
I
G
H
T
I
N
G
&
F
A
N
S
E
C
L
A
I
R
A
G
E
S
&
V
E
N
T
I
L
A
T
E
U
R
S
Power
Cord
Chain
Connector
Lower
Canopy
Nipple
Upper
Connector
Nipple
Hex Nut
Outlet Box
Outlet Box Screws
(not included)
Mounting
Bracket
Canopy
Nut
Nut
1. Attach the mounting bracket to the
outlet box using electrical box screws
(not included) . Attach the nipple to the
mounting bracket and adjust until it will
clear the canopy when assembled (Place
the canopy over the nipple and tighten
the upper connector onto the nipple
until snug. The upper connector should
hold the canopy snug to the ceiling).
Lock the nipple in the correct position
using the hex nut.
2. To attach chain loop to light fixture,
use a screwdriver and wrench to open
and close chain loop. Ensure to close
the opening. Weave the power cord and
ground wire through the links in the
chain.
3. Loosen the nut on the upper
connector and slide it down the chain
towards the lower connector. Slide the
canopy down the chain towards the
lower connector. Feed the wire through
nut, canopy, the upper connector and
onto the nipple. Tighten the upper
connector onto the nipple. Spread the
other end of the chain open and fasten
to the upper connector. Ensure to close
the opening.
4. Connect the ground wires (bare
copper or green) from your fixture to the
ground wire (bare copper or green) or
ground screw in the
electrical outlet box. Connect the black
wire (or wire marked “SPT-1”) from the
fixture to the black wire in the electrical
box and connect the white wire from the
fixture to the white wire in the electrical
box.
5. Once connections of wires are
completed, carefully tuck wires and wire
nuts into the outlet box making sure no
bare wire (on the black and white) is
visible at the wire nuts. Slide canopy
into position and tighten in place by nut
into position.
Note: If required, hook the support arms
onto fixture and then into the glass (or
hoop).
Note: If required assemble centre body
of fixture.
Note: If your product does not have any
uplights, please proceed to Step#8.
Note: If required, spread the arms of the
fixture out evenly.
TOOLS AND MATERIALS REQUIRED:
Phillips
Screwdriver
Wire Cutters
Pliers Wrench
Wiring supplies
as required by
the Canadian
Electrical Code
and/or the
Quebec
Electrical code
!
“INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS”
“READ ALL INSTRUCTIONS”
“IMPORTANT SAFETY
INSTRUCTIONS”
“SAVE THESE INSTRUCTIONS”
White
Black
House supply
Ground wire
Fixture
Ground
wire
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
3. CONNECT THE GROUND WIRE (BARE COPPER OR GREEN) FROM YOUR FIXTURE TO THE GROUND
WIRE (BARE COPPER OR GREEN) OR GROUND SCREW IN THE ELECTRICAL OUTLET BOX.
4. CLEAN GLASS WITH WATER ONLY.
NOTE: Product May Not Look Exactly As Shown In Figures.
Imported By: CANARM LTD., 2157 Parkedale Ave., Brockville, Ontario, K6V 5V6, Tel: [phone], Fax: [phone]