Installation Guide

5. Connect the ground wires
(bare copper or green) from
your fixture to the ground wire
(bare copper or green) or
ground screw in the electrical
outlet box. Connect black wire
from fixture to black wire in
outlet box and connect the
white wire from fixture to white
wire in outlet box.
Note: Do not disconnect wires
that are already connected.
6. Tuck electrical wires into
outlet box and position fixture
over studs or nipple on
mounting bracket assembly.
Secure fixture in place with star
washer(s) and cap nut(s).
NOTE: Step #7 may or may not
be required.
7. Style#1 Remove spinner
nut from the socket. Place the
glass onto the fixture socket.
Style#2 Snap glass onto fixture
(push, or push and turn (it
depends on the style of your
fixture).
Style#3 Remove the finishing
screws that are already on your
fixture. Position glass in place
and secure with finishing
screws.
8. Install proper bulb type
and wattage(not included).
1. Note: Remove fixture pan,
plate and rods if required (If you
wish to change the downrod
length) Install the length of rod
that is required by threading
wire through the rod and
securing it to the fixture.
2. Install swivel to the rod,
ensuring that the sleeve is at the
swivel. Tighten the locking nut
to secure rod to the fixture
3. Refer to the mounting
bracket style that matches the
bracket that is included with
your fixture.
Style#1 (Non-Threaded holes)
Loosen hex nut “A” and “B”.
Adjust stud so it clears the
fixture once assembled. Hold in
place with “A” and lock in place
with “B”.
Style#2 (Threaded holes)
Loosen “B”. Adjust stud to
desired length and lock in place
with “B”.
Style#3 (Nipple)
Attach nipple to mounting
bracket and adjust until it will
clear fixture when assembled.
Lock in place using the hex nut.
4. Attach ground wire to
outlet box ground screw. Mount
the mounting bracket to outlet
box using outlet box screws
(not included). Make sure the
studs or nipple on the
mounting bracket are facing out
from the outlet box.
INSTALLATION:
Rod
Fixture
Wire
Locking
Nut (optional)
Sleave
Rod
Swivel
Fixture
Wire
SUSPENDED
TRACK LIGHTING
T-1
09-12
L
I
G
H
T
I
N
G
&
F
A
N
S
E
C
L
A
I
R
A
G
E
S
&
V
E
N
T
I
L
A
T
E
U
R
S
SAFETY PRECAUTIONS:
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE
BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
3. CONNECT THE GROUND WIRES (BARE COPPER OR GREEN) FROM YOUR FIXTURE TO THE GROUND
WIRE (BARE COPPER OR GREEN) OR GROUND SCREW IN THE ELECTRICAL OUTLET BOX.
NOTE: Product May Not Look Exactly As Shown In Figures.
QUESTIONS OR CONCERNS CONTACT CANARM AT:
1-800-265-1833 (English) / 1-800-567-2513 (French) Monday through Friday 8:00 AM to 5:00 PM E.S.T.
!
“INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS”
“READ ALL INSTRUCTIONS”
“IMPORTANT SAFETY
INSTRUCTIONS”
“SAVE THESE INSTRUCTIONS”
TOOLS AND MATERIALS REQUIRED:
Wire Cutters
Pliers Wrench
Wiring supplies
as required by
the Canadian
Electrical Code
and/or the
Quebec
Electrical code
Phillips
Screwdriver
White
Black
House supply
Ground wire
Fixture
Ground wire
Star
Washer
Cap
Nut
Fixture
Stud
Glass
Tool
Fixture
Socket
Spinner
nut
STYLE#2
STYLE#3
Glass
Fixture
Socket
Finishing
Screws.
STYLE#1
Imported By: CANARM LTD., 2157 Parkedale Ave., Brockville, Ontario, K6V 5V6, Tel: [phone], Fax: [phone]
STYLE#1
STYLE#2
STYLE#3
STYLE#3
STYLE#2
STYLE#1
Outlet
Box
Outlet
Box Screws
(not included)
Mounting
Bracket
Nipple
Hex Nut
“A”
“B”
Studs
Studs
“B”