Installation Sheet

I
I
N
N
S
S
T
T
A
A
L
L
L
L
A
A
T
T
I
I
O
O
N
N
I
I
N
N
S
S
T
T
R
R
U
U
C
C
T
T
I
I
O
O
N
N
S
S
DUAL MOUNT SERIES
QUESTIONS OR CONCERNS CONTACT CANARM AT:
1-800-265-1833 (English)
1-800-567-2513 (French)
Monday through Friday 8:00 a.m. to 5:00 p.m. E.S.T.
CF-10
12/15
CANARM LTD.
2157 Parkedale Ave.,
Brockville, Ontario
K6V 5V6
PH: [phone]
FX: [phone]
CANARM L
TEE.
2555 Rue Bernard
Lefebvre, Laval, Quebec
H7C 0A5
PH: [phone]
FX: [phone]
NOTE: FOR OPTIMUM QUIETNESS, FULLY ASSEMBLE FAN AND RUN 24 HOURS
!
TOOLS AND MATERIALS REQUIRED
- Philips Screw Driver
- Blade Screw Driver
- Step Ladder
- Wire Cutters
- Wiring supplies as required by electrical code.
Pg. #12
TROUBLESHOOTING
TROUBLE
SUGGESTIONS
- Check fuses and circuit breakers.
1. Fan will not start - Check wiring connections to fan.
- Check wiring connections in switch housing.
CAUTION: Turn power off for last two items.
2. Fan sounds noisy - Check to make sure that all screws in motor housing are snug.
- Check to make sure that blade bracket screws are tight.
- Check to make sure that marrettes in switch housing
are not rattling against wall of switch housing.
- If fan has a light kit make sure switch housing
screws and set screws are tight.
- Some fan motors are sensitive to signals from solid
state variable controls. If solid state controller is
used, change to an alternative control. (See a
Canarm representative for a list of available controls.)
- Allow a 24 hour break in period to eliminate most noises.
3. Fan wobbles - Check that all blades are screwed firmly into blade brackets.
or shakes
excessively.
- Check that blade brackets are secured firmly to motor.
- Check distance from tip of blades to ceiling. Gently bend up or
down the blade brackets until all
distances are the same.
- Check distance between blade tip to blade tip. All
measurements should
be equal. Loosen blade
screws and position blade until even then re-tighten.
- Check that the downrod hemisphere notch is engaged in canopy.
- Check to make sure that jam screws in downrod are tightened.
- Make sure canopy and mounting bracket are
tightened securely to wooden joist.
- Make sure warpage has not occurred in wooden
blades. If so, contact the Canarm customer service
department for replacement parts.
“INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS”
“READ ALL INSTRUCTIONS”
“IMPORTANT SAFETY
INSTRUCTIONS”
“SAVE THESE INSTRUCTIONS”
INSTALLATION AND WIRING TO BE IN ACCORDANCE WITH CEC,
NEC, LOCAL ELECTRICAL CODES and ANSI/NFPA 70.
Consult a qualified electrician if you are not familiar with wiring.
CANARM 5 YEAR LIMITED WARRANTY
“THANK YOU” for purchasing a Canarm product. It is our policy to furnish you with
high quality products at a fair price. With proper installation your fan should provide you with
years of money saving comfort.
This fan is guaranteed to be free from defects in workmanship and material for a
period of five (5) years from date of purchase. Within the first (1) year from date of
purchase any defective product should be returned to your
RETAIL OUTLET along with proof
of purchase. For the balance of the warranty, four (4) years, the
MOTOR WINDINGS ONLY
shall be free of defects. We will correct such defects or replace the motor assembly at our
option if the product is returned,
FREIGHT PREPAID, to Canarm. The returned fan must be
accompanied by
your proof of purchase and a cheque for $20.00 for handling and
labour charges.
All costs of removing and re-installing the product are
YOUR RESPONSIBILITY.
Damage to any part as such by accident, misuse, improper installation or by affixing any
accessories
IS NOT covered by this warranty. As a result of varying climatic conditions in our
area this warranty does not cover any changes in finishes, including rusting, pitting, corroding,
tarnishing or peeling.
WARRANTY VOID: In cases of alteration, abuse, installation not in accordance with
instructions or REMOVAL of the C.S.A. Sticker.