Installation Sheet

Fig. 10e,
Pg. #4
NOTE: All set screws must be checked and
retightened where necessary, before and after
installation.
MOUNTING OPTION
CAUTION
Upper Jam
Screw
Upper Jam
Screw
Do not loosen two lower jam screws
Bolt
Yolk
Yolk
Nut
Flat Washer
Lock Washer
Cotter
Pin
INST
INST
ALLA
ALLA
TION
TION
DOWNROD MOUNT
- Using a Philips screwdriver loosen the two upper jam screws on the yoke.
- Position downrod inside canopy.
- Route wires exiting yoke on motor through ceiling canopy and downrod.
- Position downrod/canopy into yoke and align holes in yoke and downrod.
- Insert bolt through hole in yoke and downrod. “Be careful not to damage
or cut the fan wires.”
- Tighten flat washer, lock washer, and nut and bolt (not included on some
models ). Secure with cotter pin through hole in the end of the bolt.
- Secure downrod in position by tightening upper jam screws.
1.
A
FLUSH MOUNT
- Remove the yoke screws and lockwashers which correspond to the holes
- Optional for some models -Remove rubber ring from canopy (see fig. 2d)
in the canopy.
- Position canopy over the holes on motor and secure with the same screws
and lockwashers removed in the previous step. Ensure to place the rubber bushing
between the canopy and motor.
B
Motor
Rubber
Bushing
Canopy
Yoke Screws
& Washers
Motor
Canopy
Yoke Screws
& Washers
Rubber
Bushing
Fig. 2a
Fig. 2b
Fig. 2c
Fig. 2e
Fig. 2f
8.
A
LIGHT KITS (Optional in some fans)
DETACHABLE LIGHT KITS
- Remove light kit screws and washers.
- Connect polarized connectors of light kit to corresponding connectors
found in switch housing.
WARNING: BE SURE TO TURN OFF POWER
BEFORE INSTALLING
- Carefully tuck electrical wires back into switch housing, align light kit with
switch housing and secure with three light kit screws and washers.
Place shades on light kit and secure with either screws,
finger tight,spinner nut or push and turn for pop-off style
shades.(See Fig.10a,Fig.10b,Fig.10c,Fig.10d,Fig.10g,
Fig.10h,Fig.10i).
- Install proper wattage and type of bulb identified on light
kit or shade.
- Ensure that bulb sockets are attached in a parallel
direction to the hanging chains. Install proper bulb type
wattage, ensuring that pull chains do not rest on bulbs.
Motor
Red, Blue or
Black Wires
Red, Blue or
Black Wires
Light Kit
Screws
Light Kit
Switch Housing
White Wires
Lock washer
Fig. 10a
Chain
Lock
washer
Light Kit
Screw
Shade
Thumb
Screw
Light Kit
Fig. 10b
Fig. 10c
Glass
Fixture Socket
Spinner Nut
Tool
- Install proper wattage and type of bulb
identified on light housing or shade.
- Place glass on light housing and secure
(See Fig.10f).
White wire
Light lit
screws
Glass
Decorative
cover
Finial
Fibre washer
Nut
Fig. 10f
Fig. 10e
Rubber
washer
Steel
washer
Red or Blue
Wires
Black or Blue
Wires
-
Light Kit Screw
Light Kit
Switch Housing
Switch Housing
Fig. 10g
Tool
Spinner Nut
Spinner Nut
Light Kit
White wire
White wire
Red or Blue Wires
Black or Blue Wires
Pg. #9
Fibre washer
(Optional)
Fig. 10d
Canopy
Rubber
ring
Fig. 2d
Optional
for
some models
for your model)
(Refer to one of the following light kits
White wire