Installation Instructions

4. Once connections of wires
are completed, carefully tuck
wires and wire nuts into the
outlet box making sure no bare
wire (on the black and white) is
visible at the wire nuts. Install
the light fixture to the wall by
aligning the hole(s) in the
fixture with the studs or nipple
on the mounting bracket.
Secure in place with cap nut(s)
and star washer (s).
Note: If required, assemble body
and spread the arms of the fixture
out evenly.
5. Note: Refer to the style of
assembly that matches the style of
your fixture.
Style#1 - Place the decorative ring
over the glass shade. Attach the
glass shade to the fixture socket
using the thumb screws (tighten
with fingers only). Install proper
bulb type and wattage (not
included).
Style#2 - Squeeze the clips
together around the socket. Slide
the glass over the clips, then push
the glass up snug to the fixture
head.
Style#3 - Remove spinner nut from
socket. Position glass on the fixture
and secure with spinner nut.
Style#4 - Secure the glass in place
using the fibre washer, hex nut,
decorative cap and finial.
1. Note: Refer to the mounting
bracket style that matches the
bracket that is included with your
fixture.
Style#1 (Non-Threaded holes)
Loosen hex nut “A” and “B”. Adjust
stud so it clears the fixture once
assembled. Hold in place with “A”
and lock in place with “B”.
Style#2 (Threaded holes)
Loosen “B”. Adjust stud to desired
length and lock in place with “B”.
Style#3 (Nipple)
Attach nipple to mounting bracket
and adjust until it will clear fixture
when assembled. Lock in place
using the hex nut.
2. Mount the mounting bracket
to outlet box using outlet box
screws (not
included). Make sure the studs or
nipple on the mounting bracket are
facing out from the outlet box.
3. Connect the ground wires
(bare copper or green) from your
fixture to the ground wire (bare
copper or green) or ground screw
in the electrical outlet box. Connect
black wire from fixture to black wire
in outlet box and connect the white
wire from fixture to white wire in
outlet box.
STYLE#1
STYLE#2
STYLE#3
STYLE#3
STYLE #1
STYLE #2
Studs
Nipple
Hex Nut
“A”
“B”
“B”
Studs
Outlet
Box
Star
Washer
Outlet
Box Screws
(not included)
Ground
Wire
Mounting
Bracket
Stud
Or
Nipple
Cap
Nut
SF-2
10/11
Fixture
Fixture
Head
Thumb
Screws
STYLE#1
STYLE#2
STYLE#3
Fixture
Head
Clips
Glass
Spinner
Nut
Fixture
Socket
SEMI-FLUSH MOUNT
STYLE#4
Fixture
Finial
Cap
Decorative
Glass
Hex
Nut
Fibre
Washer
SAFETY PRECAUTIONS:
INSTALLATION:
L
I
G
H
T
I
N
G
&
F
A
N
S
E
C
L
A
I
R
A
G
E
S
&
V
E
N
T
I
L
A
T
E
U
R
S
QUESTIONS OR CONCERNS CONTACT CANARM AT:
1-800-265-1833 (English) / 1-800-567-2513 (French) Monday through Friday 8:00 AM to 5:00 PM E.S.T.
!
“INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS”
“READ ALL INSTRUCTIONS”
“IMPORTANT SAFETY
INSTRUCTIONS”
“SAVE THESE INSTRUCTIONS”
TOOLS AND MATERIALS REQUIRED:
Phillips
Screwdriver
Wire Cutters
Wiring supplies
as required by
the Canadian
Electrical Code
and/or the
Quebec
Electrical code
White
Black
House supply
Ground wire
Fixture
Ground wire
Imported By: CANARM LTD., 2157 Parkedale Ave., Brockville, Ontario, K6V 5V6, Tel: [phone], Fax: [phone]
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE
BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
3. CONNECT THE GROUND WIRES (BARE COPPER OR GREEN) FROM YOUR FIXTURE TO THE GROUND
WIRE (BARE COPPER OR GREEN) OR GROUND SCREW IN THE ELECTRICAL OUTLET BOX.
4. CLEAN GLASS WITH WATER ONLY.
NOTE: Product May Not Look Exactly As Shown In Figures.