Installation Instructions
OUTDOOR POST LIGHT
1. Pour cement base for the lamp.
2. Place anchor bolts into the cement with the base plate sitting on top of the
cement holding the bolts in proper position. Make sure the anchor bolts are
above the cement sufficiently to clear through the base when assembled. Make
sure the power supply passes through the centre hole of the base plate. (Note:
make sure the surface of the cement is level). After the cement is cured, proceed
with the next step.
3. Assemble the three arms to the centre post using two hex nuts and two
lockwashers for each one.
4. Screw the centre nipple into the bracket in the centre post and secure
using a hex nut.
5. Place the top cap over the centre nipple. Tighten the top cap to the centre
post by tightening a rubber gasket and nut on the centre nipple.
6. Attach the finial to the centre nipple tightening the finial against the top
cap and centre post.
7. Feed the power leads up through the base and bolt the base to the anchor
bolts using anchor bolt nuts.
8. Feed the power supply through the lower post and upper post. Feed power
supply through the cable tie. Tighten the cable tie so that the power supply
tightens against the bar.
9. Connect the power supply to the head assembly. Attach the black wire to
the black wires. Attach the white wire to the white wires. Ground wire from
power supply should be attached to ground wire from bar inside the head
assembly.
10. Screw the upper post into the head assembly (be careful not to twist the
wires).
11. Screw the lower post into the upper post.
12. Set the assembled pieces (lower post, upper post & head assembly) onto
the base and secure in place using bolts.
13. Unscrew the finial and remove the finial and the top cap of each lantern
(3 lanterns). Install the proper bulb type and wattage (not included). Place the
top cap back on the fixture and secure in place by threading the finial back onto
the nipple until it is snug.
INSTALLATION:
Finial
Arm
Finial
Centre Post
Bracket
Nuts
Lockwashers
Nut
Nut
Rubber Gasket
Rubber Gasket
Centre Nipple
Top Cap
Nipple
Upper
Post
Lower
Post
Base
Base Plate
Anchor Bolts
Power
Bolts
Top
Cap
Anchor Bolt
Nuts
Bar
Ground
Head Assembly
Upper
Post
Cable Tie
Power
Supply
White
Black
Head Assembly
Imported By: CANARM LTD., 2157 Parkedale Ave., Brockville, Ontario, K6V 5V6, Tel: (613) 342-5424, Fax: (800) 263-4598
O-9
08/12
SAFETY PRECAUTIONS:
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE HAZARDS INVOLVED.
3.
CONNECT THE GROUND WIRE (BARE COPPER OR GREEN) FROM YOUR FIXTURE TO THE GROUND
WIRE (BARE COPPER OR GREEN) OF SUPPLY WIRE.
NOTE: PRODUCT MAY NOT LOOK EXACTLY AS SHOWN IN FIGURES.
QUESTIONS OR CONCERNS CONTACT CANARM AT:
1-800-265-1833 (English) / 1-800-567-2513 (French) Monday through Friday 8:00 AM to 5:00 PM E.S.T.
L
I
G
H
T
I
N
G
&
F
A
N
S
E
C
L
A
I
R
A
G
E
S
&
V
E
N
T
I
L
A
T
E
U
R
S
!
INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS
READ ALL INSTRUCTIONS
IMPORTANT SAFETY
INSTRUCTIONS
SAVE THESE INSTRUCTIONS
TOOLS AND MATERIALS REQUIRED:
Wire Cutters
Pliers Wrench
Wiring supplies
as required by
the Canadian
Electrical Code
and/or the
Quebec
Electrical code
Star-headed
Screwdriver