Installation Instructions

1. Mount the
mounting bracket to
outlet box using outlet
box screws (not
included). Make sure
the studs or nipple on
the mounting bracket
are facing out from the
outlet box.
2. Position mounting
bracket so that the
fixture will sit level
once it is mounted to
the wall. Tighten
screws “A” and “B” to
hold in place.
3. Firmly attach the
fixture ground wire
(bare copper) to the
mounting bracket with
the ground screw (by
wrapping around the
ground screw) and
then connect it to the
house supply ground
wire with a wire nut.
Connect black wire
from fixture to black
wire in outlet box and
connect the white wire
from fixture to white
wire in outlet box.
ELECTRICAL BOX SCREWS
(not included)
Imported By: CANARM LTD., 2157 Parkedale Ave., Brockville, Ontario, K6V 5V6, Tel: [phone], Fax: [phone]
ELECTRICAL BOX
MOUNTING
BRACKET
STUD
ELECTRICAL
BOX
“A”
“B”
STUDS
HOUSE SUPPLY
GROUND WIRE
FIXTURE
GROUND WIRE
GROUND
SCREW
GROUND
SCREW
BLACK WIRE
SAFETY PRECAUTIONS:
OUTDOOR LIGHTING
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE HAZARDS INVOLVED.
3. THIS FIXTURE CAN ONLY BE MOUNTED ON A WEATHERPROOF OUTLET BOX AND IS PROVIDED WITH
A GASKET.
4. ENSURE THAT THE OUTLET BOX IS MARKED "FOR USE IN WET LOCATIONS."
5. FIRMLY ATTACH THE FIXTURE GROUND WIRE (BARE COPPER) TO THE MOUNTING BRACKET WITH THE
GROUND SCREW (BY WRAPPING AROUND THE GROUND SCREW) AND THEN CONNECT IT TO THE
HOUSE SUPPLY GROUND WIRE WITH A WIRE NUT.
QUESTIONS OR CONCERNS CONTACT CANARM AT:
1-800-265-1833 (English) / 1-800-567-2513 (French) Monday through Friday 8:00 AM to 5:00 PM E.S.T.
INSTALLATION:
WHITE WIRE
L
I
G
H
T
I
N
G
&
F
A
N
S
E
C
L
A
I
R
A
G
E
S
&
V
E
N
T
I
L
A
T
E
U
R
S
!
“INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS”
“READ ALL INSTRUCTIONS”
“IMPORTANT SAFETY
INSTRUCTIONS”
“SAVE THESE INSTRUCTIONS”
TOOLS AND MATERIALS REQUIRED:
Phillips
Screwdriver
Wire Cutters
Pliers Wrench
Wiring supplies
as required by
the Canadian
Electrical Code
and/or the
Quebec
Electrical code
IOL162
12/10
CAP NUT
STAR
WASHER
4. Once connections of wires are
completed, carefully tuck wires
and wire nuts into the outlet box
making sure no bare wire (on the
black and white) is visible at the
wire nuts. Install the light fixture
to the wall by aligning the hole(s)
in the fixture with the studs or
nipple on the mounting bracket.
Secure in place with cap nut(s) and
star washer (s).
5. Install the proper bulb type
and wattage (not included).
6. Assemble the light fixture by
attaching the (4) cap nuts until
they are snug.
7. Screw the finial into the
fixture.
Note: After Installation, seal
around the top and side perimeter
between the fixture and the wall
surface with weather resistant
caulking. The bottom should be
left un-caulked to prevent
moisture build-up.
CAP NUTS
FINIAL