Installation Instructions

ManualsBrandsCanarm ManualsLighting & Ceiling FansLtd. Yuna Black 1 Light Outdoor Pendant

TOOLS AND MATERIALS REQUIRED:

Phillips

Screwdriver

Wire Cutters

Pliers Wrench

INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS

READ ALL INSTRUCTIONS

IMPORTANT SAFETY

INSTRUCTIONS

SAVE THESE INSTRUCTIONS

Wiring supplies

as required by

local electrical

code

INSTALLATION:

IOL429

01/19

Step 1

Step 2 Step 3

Insert glass as shown.

Position glass behind 2 clips.

Position the clip over the stud

on the fixture and secure it with

the nut.

Repeat steps for other glasses.

Glass

Clip

SAFETY PRECAUTIONS:

OUTDOOR LIGHTING

1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.

2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY

A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE

HAZARDS INVOLVED.

3. CONNECT THE GROUND WIRES (BARE COPPER OR GREEN) FROM YOUR FIXTURE TO THE GROUND

WIRE (BARE COPPER OR GREEN) OR GROUND SCREW IN THE ELECTRICAL BOX.

4. TO CLEAN THE FIXTURE, TURN OFF THE POWER, WAIT FOR IT TO COOL, AND WIPE THE FIXTURE WITH

A CLEAN, SOFT CLOTH.

NOTE: Product may not look exactly as shown in figures.

QUESTIONS OR CONCERNS CONTACT AT:

1-800-265-1833 (English) / 1-800-567-2513 (French)

Monday through Friday 8:00 AM to 5:00 PM E.S.T.

Clip

Nut

Nipple

Upper

Connector

Determine the height that you would like to hang your

fixture. Trim the cord and chain. Allow 10” of extra

wiring for the electrical box connections.

Loosen the upper connector from nipple.

Summary of content (4 pages)

PAGE 1
OUTDOOR LIGHTING IOL429 01/19 QUESTIONS OR CONCERNS CONTACT AT: 1-800-265-1833 (English) / 1-800-567-2513 (French) Monday through Friday 8:00 AM to 5:00 PM E.S.T. ! INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS READ ALL INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS TOOLS AND MATERIALS REQUIRED: Phillips Screwdriver Wire Cutters Pliers Wrench Wiring supplies as required by local electrical code SAFETY PRECAUTIONS: 1.
PAGE 2
Step 3 Step 4 Electrical Box Mounting Bracket Cord Nipple Chain Hex Nut Lower Connector Electrical Box Screws (not included) Thread nipple into mounting bracket, adjust nipple so it clears the canopy when installed. Lock in place by threading hex nut onto nipple and tighten against mounting bracket. Attach mounting bracket to electrical box with electrical box screws (not included). To attach chain loop to light fixture, use a screwdriver and wrench to open and close chain loop.
PAGE 3
ECLAIRAGE EXTERIEUR IOL429 01/19 QUESTIONS OU INFORMATION COMMUNIQUE AVEC AU: 1-800-265-1833 (Anglais) / 1-800-567-2513 (Français) Du lundi au vendredi entre 8:00H et 17:00H H.N.E.
PAGE 4
Étape 3 Étape 4 Boite Electrique Ferrure De Montage Cordon Bout Fileté Chaine Écrou Connecteur Ecrou De Boite Electrique (en sus) Faufilez le bout en travers de la ferrure de montage et ajustez-le afin qu’il dépasse la cloche lorsqu’elle sera installée. Barrez en place à l’aide de l’écrou hexagonal que vous serrez contre la ferrure de montage. Posez la ferrure de montage à la boîte électrique à l’aide des vis fournies.