Installation Instructions

PENDAN T
“A”
“B”
“B”
Studs
STYLE#2
Studs
STYLE#1
Glass
Fixture Socket
Spinner Nut
Tool
STYLE#1
STYLE#1
STYLE#2
STYLE#2
STYLE#3
Fixture Head
Fixture Head
Thumb Screws
Clips
4. Firmly attach the fixture
ground wire (bare copper) to the
mounting bracket with the ground
screw (by wrapping around the
ground screw) and then connect it
to the house supply ground wire
with a wire nut. Connect the black
wire (or wire marked “SPT-1”) from
the fixture to the black wire in the
electrical box and connect the
white wire from the fixture to the
white wire in the electrical box.
5. Once connections of wires
are completed, carefully tuck wires
and wire nuts into the outlet box
making sure no bare wire (on the
black and white) is visible at the
wire nuts. Install the light fixture to
the wall by aligning the hole(s) in
the fixture with the studs or nipple
on the mounting bracket. Secure
in place with cap nut(s) and star
washer (s).
6. Mounting Glass To Fixture
NOTE: Refer to the style of
assembly that matches the style of
your fixture.
STYLE #1 - Using thumb screws
provided, attach the glass to the
fixture head. Place the glass into
the fixture head and tighten
screws into the groove or holes in
the glass.
STYLE #2 - Remove spinner nut
from socket. Position glass on lamp
and secure with spinner nut. On
some fixtures, a tool is included to
attach the spinner nut.
STYLE #3 - Squeeze the two clips
together around the socket. Slide
the glass over the clips, then push
the glass up snug to the fixture
head.
7. If not already done,install
proper bulb type and wattage
(not included) .
2. Attach the mounting
bracket to the outlet box using
electrical box screws (not
included).
3. Adjusting the length of
flexible cord. For safety, do not
release the knot inside canopy.
STYLE #1 - Loosen the plastic
screw for adjusting the length of
flexible cord. Re-tighten plastic
screw after adjusting.
STYLE #2 - Adjust the height of
the fixture by pushing the button.
Ensure the cord does not touch
the light bulb (s) when adjusting
the height of the fixture or the
steel cable (s).
INSTALLATION:
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE
BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
3. FIRMLY ATTACH THE FIXTURE GROUND WIRE (BARE COPPER) TO THE MOUNTING BRACKET WITH
THE GROUND SCREW (BY WRAPPING AROUND THE GROUND SCREW) AND THEN CONNECT IT TO
THE HOUSE SUPPLY GROUND WIRE WITH A WIRE NUT.
4. CLEAN GLASS WITH WATER ONLY.
NOTE: Product May Not Look Exactly As Shown In Figures.
SAFETY PRECAUTIONS:
LIGHT
1. Refer to the mounting
bracket style that matches the
bracket that is included with your
fixture.
Style#1 - Loosen hex nut “A”and
“B”.Adjust stud so it clears the
fixture once assembled.Hold in
place with“A”and lock in place
with“B”.
Style#2 (Threaded holes)
Loosen“B”.Adjust stud to desired
length and lock in place with“B”.
QUESTIONS OR CONCERNS CONTACT CANARM AT:
1-800-265-1833 (English) / 1-800-567-2513 (French) Monday through Friday 8:00 AM to 5:00 PM E.S.T.
!
“INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS”
“READ ALL INSTRUCTIONS”
“IMPORTANT SAFETY
INSTRUCTIONS”
“SAVE THESE INSTRUCTIONS”
TOOLS AND MATERIALS REQUIRED:
Wire Cutters
Pliers Wrench
Wiring supplies
as required by
the Canadian
Electrical Code
and/or the
Quebec
Electrical code
Phillips
Screwdriver
Canopy
White
Black
House supply
Ground wire
Fixture
Ground wire
Star
Washer
Cap Nut
Fixture
Stud
Outlet Box
Screws (not included)
Outlet
Box
Mounting
Bracket
C-11
10/11
Imported By: CANARM LTD., 2157 Parkedale Ave., Brockville, Ontario, K6V 5V6, Tel: [phone], Fax: [phone]