Instructions / Assembly

1. NOTE: Refer to the style of
assembly that matches the style
of your fixture.
STYLE A - Thread nipple into
mounting bracket, adjust nipple
so it clears fixture when installed.
Lock in place by threading hex
nut onto nipple and tighten
against mounting bracket. Attach
mounting bracket to electrical
box with electrical box screws
(not included).
STYLE B - Feed power cords from
the outlet box through the centre
hole of the back cover. Align
holes of back cover over outlet
box and secure with outlet box
screws (not included).
NOTE: Make sure the back cover
is level before tightening the
screws.
2. Additional support may be
required for fixtures longer than
20”
. Position the fixture and add
wood screws (one on each side)
for the wooden studs or plastic
wall anchor and wood screws for
dry wall.
3. Connect the ground wires
(bare copper or green) from your
fixture to the ground wire (bare
copper or green) or ground screw
in the electrical outlet box.
Connect black wire from fixture
to black wire in outlet box and
connect the white wire from
fixture to white wire in outlet box.
NOTE: Do not disconnect any
pre-wired connections.
4. NOTE: Refer to the style of
assembly that matches the style
of your fixture.
Once connections of wires are
completed, carefully tuck wires
and wire nuts into the outlet
box making sure no bare wire
(on the black and white) is
visible at the wire nuts.
STYLE #1 - Position fixture over
nipple or studs, securing in
place with serrated washer(s)
and cap nut(s).
STYLE #2 - To secure back cover
to the front panel, insert and
tighten the securing screw at
the top of the fixture
5. Mounting Glass To Fixture
(The glass may or may not be
included).
NOTE: Refer to the style of
assembly that matches the style
of your fixture.
STYLE #1 - Using thumb screws
provided, attach the glass to the
fixture head. Place the glass into
the fixture head and tighten
screws into the groove in the
glass.
STYLE #2 - Push and twist
socket cups onto socket. Insert
bulb. Repeat for each socket.
STYLE #3 - Squeeze the two
clips together around the
socket. Slide the glass over the
clips, then push the glass up
snug to the fixture head.
STYLE #4 - Remove spinner
nut from socket. Position glass
on the fixture and secure with
spinner nut.
Note: Glass may face up or
down.
Nipple
Hex Nut
Mounting
Serrated
Bracket
Washer
Fixture
Wall
Nipple
Cap
Nut
Or
Stud
Fixture Head
Fixture Head
Thumb Screws
Clips
Electrical
Electrical
Box
Box Screws
Screws
Electrical
Electrical
Box
Box
STYLE A
STYLE B
STYLE #1
STYLE #3
Cover
Back
Socket Cup
STYLE #2
V-2
09/17
Faceplate
STYLE #2
Back Cover
Securing
Screw
STYLE #1
Fixture
Socket
Bulb
STYLE #4
VANITY LIGHTING
Glass
Spinner
Nut
Fixture
Socket
INSTALLATION:
(not included)
(not included)
Tel: [phone], Fax: [phone]
SAFETY PRECAUTIONS:
TOOLS AND MATERIALS REQUIRED:
Phillips
Screwdriver
Wire Cutters
Pliers Wrench
!
INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS
READ ALL INSTRUCTIONS
IMPORTANT SAFETY
INSTRUCTIONS
SAVE THESE INSTRUCTIONS
QUESTIONS OR CONCERNS CONTACT AT:
1-800-265-1833 (English) / 1-800-567-2513 (French)
Monday through Friday 8:00 AM to 5:00 PM E.S.T.
Wiring supplies
as required by
local electrical
code
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE
BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
3. CONNECT THE GROUND WIRES (BARE COPPER OR GREEN) FROM YOUR FIXTURE TO THE GROUND
WIRE (BARE COPPER OR GREEN) OR GROUND SCREW IN THE ELECTRICAL BOX.
4. TO CLEAN THE FIXTURE, TURN OFF THE POWER, WAIT FOR IT TO COOL, AND WIPE THE FIXTURE WITH A
CLEAN, SOFT CLOTH. CLEAN GLASS WITH WATER ONLY.
NOTE: Product may not look exactly as shown in figures.
Wood screw
White
Black
House supply
Ground wire
Fixture
Ground wire