Installation Sheet

7. Tuck electrical wires into
outlet box and position
fixture over studs or nipple
on mounting bracket
assembly. Secure fixture in
place with star washer(s) and
cap nut(s). Proceed to step 8.
Option#2- Cord and Plug
1. Mount pre-assembled
fixture to wall using key slots
on back plate and plug into
outlet. Proceed to step 8.
8. Note: Refer to the style of
assembly that matches the
style of your fixture.
If your fixture has shades,
Style #1A - Place shade on
tube, then install proper bulb
type and wattage.
Style #1B - Install proper
bulb type and wattage,
shade then finial.
Style#2A - Remove spinner
nut from socket. Position
glass on the fixture and
secure with spinner nut.
Install proper bulb type and
wattage.
Style#2B -Snap “pop off”
head or glass onto fixture
(push, or push and turn).
Install proper bulb type and
wattage.
Note: Determine desired
mounting option prior to
proceeding with installation.
Option#1- Hard-wire
1. Remove the back plate from
the fixture by unscrewing cap
nuts and star washers.
2. Disconnect the male and
female wires on the backplate
and discard backplate wire
assembly.
3. Connect the male and female
wire from the fixture to the male
and female wires in the hardware
package.
4. Loosen “B”. Adjust stud to
desired length and lock in place
with “B”.
5. Attach ground wire on
mounting bracket assembly to
outlet box ground screw. Mount
the mounting bracket to outlet
box using outlet box screws.
Make sure the studs on the
mounting bracket are facing out
from the outlet box.
6. Connect the ground wires
(bare copper or green) from your
fixture to the ground wire (bare
copper or green) or ground screw
in the electrical outlet box.
Connect black wire from fixture
to black wire in outlet box and
connect the white wire from
fixture to white wire in outlet box.
Note: Do not disconnect wires
that are already connected on the
light.
Outlet
Box
Outlet
Box Screws
Ground
Wire
Mounting
Bracket
W-9
10/12
STYLE#2A STYLE#2B
Glass
Spinner
Nut
Fixture
Socket
WALL FIXTURE
QUESTIONS OR CONCERNS CONTACT CANARM AT:
1-800-265-1833 (English) 1-800-567-2513 (French)
Monday through Friday 8:00 AM to 5:00 PM E.S.T.
TOOLS AND MATERIALS REQUIRED:
SAFETY PRECAUTIONS:
INSTALLATION:
Blade
Screwdriver
Wire Cutters
Wiring supplies
as required by
electrical code
STYLE #1A
STYLE #1B
Finial
Shade
Bulb
Tube
Shade
Tube
Bulb
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
3. CONNECT THE GROUND WIRES (BARE COPPER OR GREEN) FROM YOUR FIXTURE TO THE GROUND
WIRE (BARE COPPER OR GREEN) OR GROUND SCREW IN THE ELECTRICAL OUTLET BOX.
Fixture
Back Plate
Wires
Star
Washer
Nipple
Cap
Nut
Fixture
Key
Slots
"B"
L
I
G
H
T
I
N
G
&
F
A
N
S
E
C
L
A
I
R
A
G
E
S
&
V
E
N
T
I
L
A
T
E
U
R
S
Back Plate
Cap
Nut
Star
Washer
Fixture
Back Plate
Fixture
Wires
“Pop Off”
Head Or
Glass
Fixture
Socket
White
Black
House supply
Ground wire
Fixture
Ground wire
Imported By: CANARM LTD., 2157 Parkedale Ave., Brockville, Ontario, K6V 5V6, Tel: [phone], Fax: [phone]
NOTE: Product May Not Look Exactly As Shown In Figures.
!
“INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS”
“READ ALL INSTRUCTIONS”
“IMPORTANT SAFETY
INSTRUCTIONS”
“SAVE THESE INSTRUCTIONS”