Instructions / Assembly

ManualsBrandsCanarm ManualsIndoor Wall LightsRyana 8" Tall Wall Sconce

IWF648B01

11/19

INSTALLATION:

SAFETY PRECAUTIONS:

TOOLS AND MATERIALS REQUIRED:

Phillips

Screwdriver

Wire Cutters

Pliers Wrench

INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS

READ ALL INSTRUCTIONS

IMPORTANT SAFETY

INSTRUCTIONS

SAVE THESE INSTRUCTIONS

QUESTIONS OR CONCERNS CONTACT AT:

1-800-265-1833 (English) / 1-800-567-2513 (French)

Monday through Friday 8:00 AM to 5:00 PM E.S.T.

Wiring supplies

as required by

local electrical

code

1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.

2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE

BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE

HAZARDS INVOLVED.

3. FOR OPTION#2- FIRMLY ATTACH THE FIXTURE GROUND WIRE (BARE COPPER) TO THE MOUNTING

BRACKET WITH THE GROUND SCREW (BY WRAPPING AROUND THE GROUND SCREW) AND THEN

CONNECT IT TO THE HOUSE SUPPLY GROUND WIRE WITH A WIRE NUT.

4. TO CLEAN THE FIXTURE, TURN OFF THE POWER, WAIT FOR IT TO COOL, AND WIPE THE FIXTURE WITH A

CLEAN, SOFT CLOTH.

NOTE: Product may not look exactly as shown in figures.

WALL FIXTURE

Option#1- Cord and Plug

1. Remove the back plate from the fixture by

unscrewing cap nuts and star washers.

2. Position the back plate on the wall and

determine screw location; insert wood screws

(one on each side) into wooden studs or plastic

wall anchors and wood screws into drywall.

Mount pre-assembled back plate to wall using

key slots on back plate. Tighten the wood screws

against the back plate.

3. Reattach the fixture to the back plate with

the star washers and cap nuts.

4. Remove spinner nut from socket. Position

shade on lamp and secure with spinner nut.

5. Install proper bulb type and wattage (not

included).

Star

Washer

Cap

Nut

Back plate

Wall

Anchor

Wood

Screw

Shade

Spinner

Nut

Switch

Note: Determine desired mounting option prior to proceeding with installation.

Bulb

Type A Max 60W

Summary of content (4 pages)

PAGE 1
WALL FIXTURE IWF648B01 11/19 QUESTIONS OR CONCERNS CONTACT AT: 1-800-265-1833 (English) / 1-800-567-2513 (French) Monday through Friday 8:00 AM to 5:00 PM E.S.T. TOOLS AND MATERIALS REQUIRED: INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS ! READ ALL INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS SAFETY PRECAUTIONS: Phillips Screwdriver Wire Cutters Pliers Wrench Wiring supplies as required by local electrical code 1.
PAGE 2
Option#2- Hard-wire 1. Remove the back plate from the fixture by unscrewing cap nuts and star washers. 7. Back plate Star Washer 2. Use a pair of sharp scissors to cut the cord. Strip 7mm from the 6” cord. 6” 6. Position mounting bracket so that the fixture will be hung properly once it is mounted to the ceiling. Tighten the screw to hold in Mounting place.
PAGE 3
MURAL IWF648B01 11/19 QUESTIONS OU INFORMATION COMMUNIQUE AVEC AU: 1-800-265-1833 (Anglais) / 1-800-567-2513 (Français) Du lundi au vendredi entre 8:00H et 17:00H H.N.E. OUTILS ET MATERIAUX REQUIS: INSTRUCTIONS CONCERNANT LE RISQUE ! D’INCENDIES OU LES DOMMAGES CORPORELS LISEZ TOUTES LES INSTRUCTIONS INSTRUCTIONS DE SÛRETÉ IMPORTANTES GARDEZ CES INSTRUCTIONS Tournevis A Phillips Pinces Fournitures électriques telles Coupeur De Fils que prescrites par les normes locales Clef MISE EN GARDE: 1.
PAGE 4
6. Placez la ferrure d’installation de façon à ce que le luminaire soit placé correctement lorsqu’il sera posé au plafond. Serrez la vis pour retenir la ferrure en place. Style #2- Câblez Écrou à tête 1. Débranchez la plaque arrière avec l'aide des rondelles étoilées et les écrous à tete. Plaque arrière Rondelle en étoile 2. Utilisez une paire de ciseaux 6” Vis Ferrure De Montage Noir Blanc pointus pour couper le cordon. Dégainez 7mm du cordon de 6’’. Cordon 3.