Instructions / Assembly

ManualsBrandsCANARM ManualsLightingPax 24 in. 1-Light Chrome LED Vanity Light Bar with Opal Glass Lens

Phillips

Screwdriver

Wire Cutters

Pliers Wrench

1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.

2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE

BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE

HAZARDS INVOLVED.

3. CONNECT THE GROUND WIRES (BARE COPPER OR GREEN) FROM YOUR FIXTURE TO THE GROUND

WIRE (BARE COPPER OR GREEN) OR GROUND SCREW IN THE ELECTRICAL BOX.

4. TO CLEAN THE FIXTURE, TURN OFF THE POWER, WAIT FOR IT TO COOL, AND WIPE THE FIXTURE WITH

A CLEAN, SOFT CLOTH.

NOTE: Product may not look exactly as shown in figures.

LVL229A24/36

10/21

Wiring supplies

as required by

local electrical

code

5. Mount the mounting

bracket to electrica

l box using

electrica

l box screws (not

included).

Connect the ground wires

(bare copper or green) from

your fixture to the ground wire

(bare copper or green) or

ground screw in the electrical

box. Attach the black wire from

the light fixture to the black wire

in the electrical box. Attach the

white wire from the light fixture

to the white wire in the electrical

box.

NOTE: Do not disconnect any

pre-wired connections.

7. Re-tighten the two screws

to install the fixture.

Tel: (613) 342-5424, Fax: (800) 263-4598

Electrical

Box

Electrical Box Screws

(not included)

Mounting

Bracket

Fixture

White

Black

House

supply

Ground

wire

Fixture

Ground wire

INSTALLATION:

SAFETY PRECAUTIONS:

TOOLS AND MATERIALS REQUIRED:

dimmable

Model#

MAX rated

wattage

Suitable dimmer

LVL229A36

30W

40W

LEVITON# 742-6672-HLW ,

722-6674-PDW MAX 150 W,

Lutron # SCL-153PH-WH MAX 150 W

These LED light are compatible with the dimmers:

LVL229A24

LED VANITY

Mounting

Bracket

Screw

1. Remove the mounting bracket from the fixture by

unscrewing the 2 screws.

2. Remove the clip at one end of the frame by

unscrewing the 2 screws.

3. Insert the glass panel (frosted side

facing out) into the other end of the frame.

Ensure the glass panel is in the groove

between the clip and the frame.

4. Re-install the clip onto the frame by tightening the 2

screws. Ensure the clips at both ends are secured.

Clip

Screw

Clip

Glass

Panel

Frame

Summary of content (2 pages)

PAGE 1
LED VANITY LVL229A24/36 10/21 TOOLS AND MATERIALS REQUIRED: Phillips Screwdriver Wire Cutters Pliers Wrench Wiring supplies as required by local electrical code SAFETY PRECAUTIONS: 1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE. 2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. 3.
PAGE 2
ÉCLAIRAGE DE VANITÉ AU DEL OUTILS ET MATERIAUX REQUIS: INSTRUCTIONS CONCERNANT LE RISQUE D’INCENDIES OU LES DOMMAGES CORPORELS LISEZ TOUTES LES INSTRUCTIONS ! LVL229A24/36 10/21 INSTRUCTIONS DE SÛRETÉ IMPORTANTES GARDEZ CES INSTRUCTIONS Tournevis Phillips Pinces Fournitures électriques telles Coupeur De Fils que prescrites par les normes locales Clef MISE EN GARDE: 1. FERMER LE COURANT AU DISJONCTEUR AVANT DE DÉBUTER L’INSTALLATION DE LA FIXTURE. 2.