Installation Guide

Imported By: CANARM LTD., 2157 Parkedale Ave., Brockville, Ontario, K6V 5V6, Tel: [phone], Fax: [phone]
7. Note: Refer to the style of
assembly that matches the style of
your fixture.
If your fixture has shades,
STYLE #1A - Place shade on tube,
then install bulb.
STYLE #1B - Install bulb, shade
then finial.
STYLE #2 - Remove spinner nut
from socket. Position glass on lamp
and secure with spinner nut.
Note: Glass may face up or down.
Note: If your fixture has candle-
style lights, slide the tubes over the
uplight sockets
STYLE #3 - Install proper bulb type
and wattage before assembling
the glass. Remove ball screw from
the curved stem. Position glass on
lamp with the curved stem being
inserted through the hole in the
glass. Hand tighten the ball screw
to secure the glass in place.
8. If not already done, install
proper bulb type and wattage.
Note: If your product does not
have a bottom light, your fixture is
complete.
9. Attach the stem to the fixture.
10. Position the glass over the
stem. Secure the glass in place
using the fibre washer, hex nut,
decorative cap and finial.
1. Attach the mounting bracket to
the outlet box using electrical box
screws and flat washers. Attach the
nipple to the mounting bracket and
adjust until it will clear the canopy
when assembled (Place the canopy
over the nipple and tighten the upper
connector onto the nipple until snug.
The upper connector should hold the
canopy snug to the ceiling). Lock the
nipple in the correct position using the
brass nut.
2. Spread one end of chain open and
fasten to the lower connector. Weave
the power cord and ground wire
through the links in the chain. Spread
the other end of the cord open and
fasten to the upper connector.
3. Feed the wires through the hole in
the upper connector. Loosen off the
nut on the upper connector and slide it
down the chain towards the lower
connector. Slide the canopy down the
chain towards the lower connector.
4. Feed the wires through the nipple
and tighten the upper connector onto
the nipple.
5. Connect the copper wire to
ground screw in electrical box. Connect
the black wire (or wire marked “SPT-1”)
from the fixture to the black wire in the
electrical box and connect the white
wire from the fixture to the white wire
in the electrical box.
6. Tuck electrical wires into electrical
box. Slide canopy into position and
tighten in place by sliding upper
connector nut into position and
tighten.
Note: If required, hook the support
arms onto fixture and then into the
glass (or hoop).
Note: If required assemble centre body
of fixture.
Note: If your product does not have
any uplights, please proceed to Step#8.
Note: If required, spread the arms of
the fixture out evenly.
REQUIRED:
SAFETY PRECAUTIONS:
INSTALLATION:
Power
Cord
Chain
Connector
Lower
Canopy
Upper Connector
Nut
Nipple
Upper
Connector
Nipple
Hex Nut
Outlet Box
Outlet Box Screws
Mounting
Bracket
Wrench
Pliers
Phillips Screwdriver
Wire Cutters
White
Black
Ground
Wire
Glass
Fixture
Socket
Fixture
Stem
Finial
Cap
Decorative
Glass
RC-2
03/03
Spinner
Nut
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.
DO NOT REMOVE INSULATION FROM FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE
BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
NOTE: Product May Not Look Exactly As Shown In Figures.
Glass
Hole
For Stem
Ball Screw
STYLE #2
STYLE #3
Wiring supplies
as required by
electrical code
Fixture
Hex
Nut
Fibre
Washer
Canopy
Nut
Questions or Concerns Contact Canarm At:
1-800-265-1833 (English) or 1-800-567-2513 (French)
Monday Through Friday 8:00am - 5:00pm E.S.T.
STYLE #1A
STYLE #1B
Finial
Shade
Bulb
Tube
Shade
Tube
Bulb
Chandelier