EN
WEEE contains both polluting substances (which can cause negative consequences for the environment) and basic components (which can be re-used). It is important to have WEEE subjected to specific treatments, in order to remove and dispose properly all pollutants, and Carefully read this manual for correct and recover and recycle all materials. Individuals can safe appliance use and for helpful tips on play an important role in ensuring that WEEE efficient maintenance.
1. GENERAL SAFETY RULES in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. This appliance is intended to be used in household and similar applications such as: - Staff kitchen areas in shops, offices and other working environments; - Farm houses; - By clients in hotels, motels and other residential type environments; - Bed and breakfast type environments.
(latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the washer dryer. never stop a washer dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated. Fabric softeners, or similar products, should be used as specified by the fabric softener instructions. After installation, the appliance must be positioned so that the plug is accessible.
To consult the product technical Do not pull on the power cord specification please refer to the manufacturer website. Electrical connections safety instructions or appliance to unplug the machine. Make sure there is no water in and the drum before opening the door. The technical details (supply voltage and power input) are indicated on the product rating plate WARNING: water may reach very high temperatures during the wash cycle.
2. INSTALLATION EN Remove the 2 or 4 transportation screws (A) on the back and remove the 2 or 4 flat washers, rubber bungs and plastic spacer tubes (B) as illustrated in figure 1. If the washing machine is builtin, unscrew the 3 or 4 transportation screws (A) and remove the 3 or 4 flat washers, rubber bungs and plastic spacer tubes (B).
Instructions for mounting the furniture door Position the template onto the reverse of the furniture door. It is possible to mount the hinges and closure magnet on the right or left-hand side depending on your requirements. Mark the screw hole positions, then drill out these positions. Fix the hinges in place with the 4 screws provided (A). Fix the magnet (B) in place using screw (C). Mount the plate (D) on the right or left-hand side, depending on your installation requirements.
Mount the furniture door to the EN front of the washer using the hinges. Fix the spacers (I) in place with the 2 screws (J) and then fix the hinges with 2 screw (H). We suggest mounting the furniture door so that it opens towards the left, which is the same direction as the porthole door. This will leave more space when you are loading washing into the appliance. Slide the washer into an opening of the size indicated in the diagram opposite.
Hydraulic connections Connect the water hose to the water supply tap (fig. 3) only using the hose supplied with the appliance (do not reuse old hose-sets). SOME MODELS may include one or more of the following features: HOT&COLD (fig. 4): water mains connection settings with hot and cold water for higher energy savings. Connect the grey tube to the cold water tap and the red one to the hot water tap.
Setting EN The washing machine should be installed in its final position such that the water fill hose is not kinked or trapped. The corrugated drain hose should be inserted into suitable drain pipe of between 50 cm and 85 cm height above the floor using the curved drain hose support. If an under sink connection is used the drain hose must be routed above the sink overfill opening to prevent back siphoning. Care must be taken to avoid kinking or trapping the drain hose (fig. 7).
3. DETERGENT DRAWER The detergent draw is split into compartments as illustrated in figure 9: 3 compartment "1": for prewash detergent; compartment “ ”: for special additives, softeners, starch fragrances, etc.; WARNING: only use liquid products; the washing machine is set to automatically dose additives at each cycle during the last rinse. compartment detergent.
Load tips Maximise the load size Achieve the best use of energy, water, detergent and time by using the recommended maximum load size. Save up to 50% energy by washing a full load instead of 2 half loads.
The use of ecological detergents without phosphates may cause the following effects: When washing heavily soiled whites, we recommend using cotton programs of 60°C or above and a normal washing powder (heavy duty) that contains bleaching agents that at medium/high temperatures provide excellent results. - cloudier rinse drain water: This effect is tied to the suspended zeolites which do not have negative effects on rinse efficiency.
Remove and clean the filter; when finished, replace it turning it clockwise. The filter handle will be locked when it is not possible to turn any further and the handle is horizontal. Smearing a small amount of liquid soap on the filter seal will help refitting. Looking after your appliance correctly can extend its lifespan. Cleaning the appliance’s exterior Disconnect the machine from the power Repeat the previous steps in reverse order to reassemble all parts. supply.
6. QUICK USER GUIDE This washing machine automatically adjusts the level of the water to the type and quantity of washing. This system gives a reduction in energy consumption and a saving in washing times. 7. CONTROLS AND PROGRAMS Program selection Turn on the washing machine and select the required program. Adjust the washing temperature if necessary and press the required "option" buttons.
When the START/PAUSE button has been pressed, the appliance can take few seconds before it starts working. When the programme selector is turned the display lights up to show the settings for the programme selected. For energy saving, at the end of the cycle or with an inactivity period, the display level contrast will decrease.
- Press the delay start button once to activate it (h00 appears on the display) and then press it again to set a 1 hour delay (h01 appears on the display). The pre-set delay increases by 1 hour each time the button is pressed, until h24 appears on the display, at which point pressing the button again will reset the delay start to zero. - Confirm by pressing the START/PAUSE button. The delay countdown will begin and when it has finished the programme will start automatically.
To prevent damage to the fabrics, it is not possible to increase the speed over the maximum allowed for the programme. This button allows you to choose between two different options, depending on the selected programme: - RAPID The button becomes active when you select the RAPID (14'/30'/44') programme on the knob and allows you to select one of three durations indicated. To reactivate the spin cycle press the button until you reach the spin speed you would like to set.
3) DOOR LOCKED INDICATOR LIGHT Digital Display The display’s indicator system allows you to be constantly informed about the status of the machine. The indicator light is illuminated when the door is fully closed. Close the door BEFORE selecting the START/PAUSE button. When START/PAUSE is pressed on the machine with the door closed, the indicator will flash momentarily and then illuminate.
6) WASH TEMPERATURE LIGHTS - recognises the presence of too much soap suds, and if necessary, adjust the amount of rinse water. This shows the washing temperature of the selected programme that can be changed (where allowed) by the relevant button. If you want carry out a cold wash all the indicators must be off. - adjusts the spin speed according to the load, thus avoiding any imbalance. 5) KEY LOCK INDICATOR LIGHT The indicator light show that the keys are locked.
Table of programmes 1) (MAX.) * PROGRAMME (see control panel) (MAX.
1) 2) 3) 4) INFORMATION FOR THE TEST LABORATORIES STANDARD PROGRAMMES ACCORDING TO Directive 96/60/CE When a programme is selected, on the display is shown the display shows the recommended wash temperature that can be reduced (where allowed) by the relevant button. WASHING: ECO 40-60 PROGRAMME SETTING THE TEMPERATURE TO 60°C For the programmes shown you can adjust the duration and intensity of the wash using the STAIN LEVEL button.
Description of programmes To clean different types of fabrics and various levels of dirt, the washing machine has specific programs to meet every need of washing (see table of programmes). Choose programme in accordance with the laundry instructions appearing on labels, especially the maximum recommended temperature. ECO 40-60 The ECO 40-60 programme is able to clean normally soiled cotton laundry declared to be washable at 40°C or 60°C, together in the same cycle.
and avoid possible felting. It’s suggested to reverse clothing before drying. Timing is related to the amount of the washing and the spin speed selected for the wash. The cycle is suitable for small loads up to 1 kg (3 sweaters). Delicates This programme has reduced periods of drum rotation during the cycle and is particularly suitable or washing delicate fabrics. The wash cycle and rinses are carried out with a high level of water to ensure the best performance.
8. DRYING CYCLE The correct way to dry Drying guidance advice is general, but practical experience of using the product will help you to achieve the best drying results. We recommend setting a lower drying time than indicated, when first using the appliance in order to establish the degree of dryness required. We recommend not drying fabrics that fray easily, such as rugs or garments with a deep pile, in order to avoid air duct clogging.
Switch off the machine by turning the programme selector to the OFF position. Open the door and remove the laundry. Turn off the tap. The washer dryer will calculate the time needed for drying and the level of moisture remaining in the laundry, according to the load and drying type selected. CANCELLING THE DRYING PROGRAMME To cancel the drying programme, press and hold the DRYING SELECTION button for about 3 seconds. Check that the tap is turned on and that the discharge correctly.
9. AUTOMATIC WASHING/ DRYING CYCLE At the end of the wash phase the display will show the drying time remaining. When the programme is finished the word You cannot exceed the maximum dryable load of laundry indicated in the programme table, otherwise the laundry will not be dried satisfactory. "End" will appear on the display. After 5 minutes the appliance will go into standby mode (on certain models, the display will show two lines).
If you believe the washing machine is not working correctly, consult the quick guide provided below which includes some practical tips on how to fix the most common problems. ERROR CODE FORMAT Models with a display: the error is shown by a number preceded by the letter “E” (example: E2 = Error 2). Models without display: an error is shown by a sequence of flashes of every LED.
OTHER ANOMALIES Problem Possible causes and practical solutions The washing machine does not work / start The washing machine does not spin Make sure the product is plugged into a working supply socket. Make sure power is on. Make sure the wall socket is working, testing it with another appliance such as a lamp. The door may not be correctly closed: open and close it again. Check whether the required program was correctly selected and the start button pressed.
Warranty The product is guaranteed under the terms and conditions stated on the certificate included with the product. The certificate has to be stored so as to be shown to the Authorized Customer Service Centre in case of need. You can also check the warranty conditions on our web site. To obtain assistance, please fill in the form on-line or contact us at the number indicated on the support page of our web site.
- CBD D E (21) - 21.06 - 70004573 - IDM s.r.l.
