INSTRUCTION FOR THE INSTALLATION AND OPERATION OF HOBS ~~~ 93786974 PA 640/2 F PA 640/2 UK 1
CONTENTS Unpacking the appliance ............................................................... 3 Recommendations ....................................................................... 3 Presentation of the hob / Technical data .......................................... 4 • INSTALLATION Safety instructions ........................................................................ 5 Modification of the factory gas setting : * Fitting of the correct jets .....................................................
UNPACKING THE APPLIANCE Inside the appliance, you will find : • a plastic bag containing : - the new jets for the gas modification, if required, - the fixing brackets with screws to install the hob in the worktop, and, • a spanner to change the jets if the factory gas setting does not correspond to your installation requirements. RECOMMENDATIONS PLEASE READ THE FOLLOWING CAREFULLY IN ORDER TO GET THE BEST FROM YOUR APPLIANCE.
PRESENTATION Sem W fast 3,2 ry Semi t1 -fas ,4 W 5k kW Ve st 2,5 k Fa st i-fa 1,4 5 kW ALL GAS HOB TOUT GAZ PA 64 0/2 F : 640/2 PA 64 640/2 0/2 UK : 4 gas burners, and cast-iron pan supports. 4 gas burners, and enamelled pan supports.
INSTALLATION Installing a domestic appliance can be a complicated operation which if not carried out correctly, can seriously affect consumer safety. It is for this reason that the task should be undertaken by a professionally qualified person who will carry it out in accordance with the technical regulations in force.
INSTALLATION: "GAS CONNECTION" • CHANGING THE GAS TYPE : the calorific power output and gas pressure will vary according to the gas supply. Burner setting must be carried out once the gas and electrical installation is complete. When changing gas type, you must follow the procedure below : . fit the correct jets, . adjust the appearance of the flame by regulating the air ring. . adjust the minimum flame on the taps (see page 12). • CHANGING THE JETS : Each jet is designated by size.
INSTALLATION: "GAS CONNECTION" • SETTING THE APPEARANCE OF THE FLAME 1. Regulating the air ring on the hob burners : the setting is important as it ensures the correct combustion and enables the burners to work at maximum efficiency. The table refers to the value "X" in mm ; it may be necessary to regulate this by plus or minus 1 mm to obtain a perfect flame. 2. To gain access to the air rings on the hob burners: remove the pan support, the burner cap and body of the relevant burner.
INSTALLATION: "BUILDING-IN" BUILDING-IN : both the unit into which the hob will be fitted and any adjacent kitchen furniture must be made from heat resistant material and fixed with heat resistant adhesive. If, when installing the hob, the lower part of the casing is adjacent to an area normally accessible when handling or cleaning, fit a partition 1 cm below the base of the casing with a 10x10 cm opening at the rear right-hand corner, to avoid any risk of burning or damage.
INSTALLATION: "BUILDING-IN" The body of the hob is fitted with 4 location holes to take the fixing brackets that secure the hob in the unit. Place the 4 fixing brackets in such a way that the hob is placed perfectly in the support unit.
INSTALLATION: "GAS CONNECTION" The hob can be built-in ; it is type "X" for built-in hob (in compliance with electrical regulations EN 60.335.2.6) ; in class 3 (in compliance with gas norm EN 30.1.1) ; adjoining furniture should not be higher than the level of the hob. This appliance is not connected to an evacuation device for the products of combustion. It must be installed and connected in compliance with the norms in force in the country of installation.
" INSTALLATION: "ELECTRICAL CONNECTION CONNECTION" The mains electricity supply connected to the appliance should comply with the norms in force in the country of installation. Connection to the mains electricity supply should be through a socket with an earth terminal, or through an intermediary switching device with a gap between contacts of at least 3 mm.
INSTALLATION: "REGULATING THE FLAME" • SETTING THE IDLE FLAME If you have changed the type of gas, it is important to verify the flame stability at the minimum regulation. "Gaining access to the by-pass screw" To gain access to hob burner by-pass screws, remove the knobs from the control panel. By-pass screw of the hob burner ! Never loosen the others screws ! REGULATING THE MINIMUM FLAME ON THE HOB BURNER a) Natural gas : . simply loosen the screw. . switch on the burner and turn the knob to minimum. .
THE GAS BURNER THE VERY FAST "DOUBLE RING" BURNER has a power rating of 3,2 kW : Use the large burner for bringing to the boil, for cooking large quantities, and generally for all foods requiring rapid cooking. THE FAST BURNER has a power rating of 2,5 kW : It is ideal for stewing, sauces and slow cooking. THE SEMI-FAST BURNER has a power rating of 1,45 kW : Use this small burner for small pans.
THE GAS BURNER Each burner is contolled by a tap with progressive settings allowing : * a wider choice of settings from the maximum position to the lowest and most precise one, * easier flame regulation according to the pan diameter, * no risk of cutting off the flame or switching off when the flame is turned down quickly. Each burner is fitted with automatic ignition. The ignition can be made with one hand, while you have the pan in the other hand.
CLEANING Before all cleaning or dismantling operation, it is imperative to : . disconnect the hob to the mains supply, . let all parts of the hob cool down down.. Never use : harsh abrasives, scouring pads or sharp object to clean the hob. • GENERAL MAINTENANCE THE HOB . Enamelled steel hob : simply clean the enamelled hob with soapy water when the hob is cold, rinse and wipe with a clean dry cloth. If you clean the enamelled hob when it is hot, you may tarnish it. .
CANDY ELETTRODOMESTICI S.R.L.