Wiring diagram Cannon FITZROY INBUILT Data plate INBUILT MODELS FITZIB-SDSEB-NG FITZIB-SDSEB-LP For service to this appliance For service to this appliance or spare parts contact the CANNON distributor. Sampford IXL 52 - 70 Sparks Avenue Fairfield, Vic, 3078 Phone: Fax: email: 24 1300 727 421 1300 727 425 service@sampfordixl.com.
Contents Contents 2 Warranty 3 2. 4-5 3. ❍ Distributor Safety warnings ❍ What to do if you smell gas ❍ Warnings ❍ Standards User instructions 4. 6-8 ❍ Operating instructions ❍ Cleaning ❍ Flame characteristics Heater specifications Installation instructions ❍ ❍ ❍ ❍ ❍ ❍ 5. 9 6. 10-14 7.
Service Instructions - (Do not modify this appliance) General 1. Service work to be carried out by an authorised service person only. 2. Unplug from wall socket or turn off power at main switchboard if heater is hard wired. 3. Always shut off the gas supply and ensure that the heater is cool before commencing any service operations. 4. Always check for gas soundness after servicing. To replace the primary glass 1. Refer pages 13 and 14, steps 7 to 11, of the installation instructions.
Safety warnings Please read this manual before installing and using the heater. 8. Sparks, ignites on low flame then extinguishes after 10 seconds. Continues to spark during flame presence. • Check that the wall socket to the appliance has correct polarity. Do not use an extension cord. Check polarity in the electrical supply lead to appliance. • Check that the sense electrode is in the flame. • Check that appliance is earthed correctly.
Trouble-shooting - (Do not modify this appliance) To check the operation of the electronic (module) controller (Type 537 ABC) you will require a digital multimeter with the functions to measure AC/DC voltage, continuity, resistance and micro-amps. It is critical that the appliance is earthed and that the active and neutrals are not reversed. Item No 1. 2. 3. 4. 5. 6. 7. 20 Check Action No ignition when appliance is turned on. • Check 240 volts power to heater in incoming plug connector.
User instructions Installation tips Operating instructions ❍ Test the operation of the chimney before installing the new heater. 1. Plug the power cord into the wall socket and turn on the power to the heater, see figure 1. Refrain from using an extension cord. ❍ Be careful! 1 2.
pressure to 0.75 kPa for Natural gas or 2.65 kPa for LPG. (Turn clockwise to increase pressure and anticlockwise to decrease pressure). 5. To increase the fan speed to MED, press switch for MED setting. Refer figure 5. 35 5 26. Switch the heat button back to “Low Flame’ position as indicated in figure 36(a), retain spanner in position and using a screwdriver as per figure 36(b) adjust the central screw control to give a pressure reading of 0.3 kPa for Natural Gas and 1.1 kPa for LPG.
Gas control Cleaning All cleaning should be carried out when the heater is cold. Normally the heater should only need wiping with a lint - free damp cloth. Any stubborn stains can be removed with a non-abrasive spray on cleaner. If an abrasive cleaner is used the paint finish will be damaged. For heater fitted with the glass front: Important: To achieve the correct visual flame effect: 23. Gas control layout is as indicated in figure 32.
Heater specifications Log installation Gas type: The data label is located on the fan chamber base, Gas consumption: rear of lower fascia. Energy output: Note: 16. The burner is contained within the burner chamber. Refer figure 27. 17. Carefully unpack the log set. Logs are numbered as follows: 27 No 1 - Left front log No 2 - Left back log 20 No 3 - Right front log No 4 - Right back log Position the four individually numbered logs in the following order on the burner head as shown in figure 28-31.
Installation instructions Gas connections 1. This appliance is to be installed by an authorised service person only. 13. Slide heater into the fireplace ensuring that gas inlet pipe is fed through the hole at the rear bottom RHS of the heater. Refer figure 24 and gas connection figure 26. 2.
For installation into a masonry or brick fireplace WITH a flue connection refer figure 12. For installation WITHOUT refer figures 13 & 14. After installation of the heater test the flue to confirm air vents are unobstructed. If an exhaust fan or other heating appliances are present switch them on. This is to test that there is no interaction between the Cannon heater and other appliances. you gently to partly disengage it from the body of the heater.
Installation WITHOUT a flue connected 15 6. Prepare electrical and gas connections. A 10 Amp wall socket needs to be located within 1.5m of the heater. If using a power point in the chimney, route the plug and cord through cord access at lower LH side of rear panel. A grommet is fitted over the cord. Ensure that the grommet is located over the edges of the access hole. Refer figure 15. Hard (fixed) wiring connection is to be carried out only by a qualified electrician. 7.
Installation WITHOUT a flue connected 15 6. Prepare electrical and gas connections. A 10 Amp wall socket needs to be located within 1.5m of the heater. If using a power point in the chimney, route the plug and cord through cord access at lower LH side of rear panel. A grommet is fitted over the cord. Ensure that the grommet is located over the edges of the access hole. Refer figure 15. Hard (fixed) wiring connection is to be carried out only by a qualified electrician. 7.
For installation into a masonry or brick fireplace WITH a flue connection refer figure 12. For installation WITHOUT refer figures 13 & 14. After installation of the heater test the flue to confirm air vents are unobstructed. If an exhaust fan or other heating appliances are present switch them on. This is to test that there is no interaction between the Cannon heater and other appliances. you gently to partly disengage it from the body of the heater.
Installation instructions Gas connections 1. This appliance is to be installed by an authorised service person only. 13. Slide heater into the fireplace ensuring that gas inlet pipe is fed through the hole at the rear bottom RHS of the heater. Refer figure 24 and gas connection figure 26. 2.
Heater specifications Log installation Gas type: The data label is located on the fan chamber base, Gas consumption: rear of lower fascia. Energy output: Note: 16. The burner is contained within the burner chamber. Refer figure 27. 17. Carefully unpack the log set. Logs are numbered as follows: 27 No 1 - Left front log No 2 - Left back log 20 No 3 - Right front log No 4 - Right back log Position the four individually numbered logs in the following order on the burner head as shown in figure 28-31.
Gas control Cleaning All cleaning should be carried out when the heater is cold. Normally the heater should only need wiping with a lint - free damp cloth. Any stubborn stains can be removed with a non-abrasive spray on cleaner. If an abrasive cleaner is used the paint finish will be damaged. For heater fitted with the glass front: Important: To achieve the correct visual flame effect: 23. Gas control layout is as indicated in figure 32.
pressure to 0.75 kPa for Natural gas or 2.65 kPa for LPG. (Turn clockwise to increase pressure and anticlockwise to decrease pressure). 5. To increase the fan speed to MED, press switch for MED setting. Refer figure 5. 35 5 26. Switch the heat button back to “Low Flame’ position as indicated in figure 36(a), retain spanner in position and using a screwdriver as per figure 36(b) adjust the central screw control to give a pressure reading of 0.3 kPa for Natural Gas and 1.1 kPa for LPG.
User instructions Installation tips Operating instructions ❍ Test the operation of the chimney before installing the new heater. 1. Plug the power cord into the wall socket and turn on the power to the heater, see figure 1. Refrain from using an extension cord. ❍ Be careful! 1 2.
Trouble-shooting - (Do not modify this appliance) To check the operation of the electronic (module) controller (Type 537 ABC) you will require a digital multimeter with the functions to measure AC/DC voltage, continuity, resistance and micro-amps. It is critical that the appliance is earthed and that the active and neutrals are not reversed. Item No 1. 2. 3. 4. 5. 6. 7. 20 Check Action No ignition when appliance is turned on. • Check 240 volts power to heater in incoming plug connector.
Safety warnings Please read this manual before installing and using the heater. 8. Sparks, ignites on low flame then extinguishes after 10 seconds. Continues to spark during flame presence. • Check that the wall socket to the appliance has correct polarity. Do not use an extension cord. Check polarity in the electrical supply lead to appliance. • Check that the sense electrode is in the flame. • Check that appliance is earthed correctly.
Service Instructions - (Do not modify this appliance) General 1. Service work to be carried out by an authorised service person only. 2. Unplug from wall socket or turn off power at main switchboard if heater is hard wired. 3. Always shut off the gas supply and ensure that the heater is cool before commencing any service operations. 4. Always check for gas soundness after servicing. To replace the primary glass 1. Refer pages 13 and 14, steps 7 to 11, of the installation instructions.
Contents Contents 2 Warranty 3 2. 4-5 3. ❍ Distributor Safety warnings ❍ What to do if you smell gas ❍ Warnings ❍ Standards User instructions 4. 6-8 ❍ Operating instructions ❍ Cleaning ❍ Flame characteristics Heater specifications Installation instructions ❍ ❍ ❍ ❍ ❍ ❍ 5. 9 6. 10-14 7.
Wiring diagram Cannon FITZROY INBUILT Data plate INBUILT MODELS FITZIB-SDSEB-NG FITZIB-SDSEB-LP For service to this appliance For service to this appliance or spare parts contact the CANNON distributor. Sampford IXL 52 - 70 Sparks Avenue Fairfield, Vic, 3078 Phone: Fax: email: 24 1300 727 421 1300 727 425 service@sampfordixl.com.