MAKER’S WARRANTY Cannon FITZROY PROFILE INBUILT MODELS FITZPIB, FITZPIBLP Cannon FITZROY PROFILE USER INSTRUCTIONS INSTALLATION INSTRUCTIONS SERVICE INSTRUCTIONS Part No: F2752 Revision B This heater is approved for use with Natural and Propane gases.
Contents Contents 2 Warranty 3 Safety warnings 4-5 ❍ What to do if you smell gas ❍ Warnings ❍ Standards User instructions 6-8 ❍ Operating instructions ❍ Cleaning Heater specifications Installation instructions ❍ ❍ ❍ ❍ 9 10-14 Clearances Fitment of cabinet depth spacer Installation into a masonry fire place Sealing Gas connection 15-16 ❍ Fuel bed & log installation Gas control 17-18 ❍ Gas pressure point ❍ Gas pressure adjustment Service instructions ❍ ❍ ❍ ❍ ❍ ❍ 19 General To replace the gas
Warranty Wiring diagram The Cannon appliance is warranted against defects in materials and workmanship for a period of one, (1) year from its date of original purchase, for residential use in Australia. Warranty service, which includes parts and labour for the replacement or repair of defective parts, is available through Cannon Authorised Service Agencies. (Please refer to the list of authorised service agents in this manual.
Safety Warnings Please read this manual before installing and using the heater. What to do if you smell gas 9 No gas to burner. • The gas valve should open at the same time as the igniter sparks. If there is no gas to the burner when this occurs check the solenoid coils for continuity. • Check that the gas pressure is present at the test point when the spark is being generated. • Check that there is gas to the inlet of the gas control. 10 Appliance lights but goes into lockout.
Troubleshooting 7. To check the operation of the electronic (module) controller (Type 537 ABC) you will require a digital multimeter with the functions to measure AC/DC voltage, continuity, resistance and micro-amps. 8. Installation and repairs should be performed by a licensed service person only, refer to back of brochure for service number. It is critical that the appliance is earthed and that the active and neutrals are not reversed. Item No Check Action 1 No ignition when appliance is turned on.
User instructions Operating instructions Service Instructions 1. Plug the power cord into the wall socket and turn on the power to the heater, see figure 1. Refrain from using an extension cord. General 1. Service work to be carried out by a licensed service person only. 2. Unplug from wall socket or turn off power at main switchboard if heater is hard wired. 3. Always shut off the gas supply and ensure that the heater is cool before commencing any service operations. 4.
Gas pressure adjustment 25. Switch the top two control buttons to “Full On” position as indicated in figure 36(a) and using a ring spanner, as per figure 36(b), adjust the pressure to 1kPa for Natural gas or 2.65 kPa for LPG. (Turn clockwise to increase pressure and anticlockwise to decrease pressure). 5. To increase the fan speed to MED, press switch for MED setting. Refer figure 5. 5 36 6. To increase the fan speed to HIGH, press switch for HIGH setting. Refer figure 6. 26.
Gas control User instructions continued Cleaning. All cleaning should be carried out when the heater is cold. Normally the heater should only need wiping with a lint - free damp cloth. Any stubborn stains can be removed with a non-abrasive spray on cleaner. If an abrasive cleaner is used the paint finish will be damaged. 23. Gas control layout is as indicated in figure 33.
Heater Specifications b) Place log No.2 onto the 2 left back pins. Refer figure 30. 30 c) Place log No.3 on single right front pin, ensure fork locates over log No. 2, see figure 31. Do not use fire with broken or missing logs. Gas type: Natural or Propane gas, as indicated on data label Gas consumption: 26 MJ/hr input Energy star rating: 3.77 Energy output: 20.7 MJ/hr Heater type: Heater approved to AS 4553/AG103. Operating pressure: Natural gas: 1.0 kPa Propane gas: 2.
Installation instructions Gas connections 1. This appliance is to be installed by a licensed service person only. 15. Connect incoming gas supply pipe to regulator. For inlet position see figure 26. Close gate over gas supply and seal around the pipe with fibreglass insulation material. Sealing is important as it prevents leakage from fan chamber into chimney: also check for gas soundness. 2.
Installation instructions continued 11 20 c Assemble the spacer by fixing the two side sections to the top sections with a s/t screw (provided) each side. Refer figure 12. 23 13. Slide heater into the fireplace ensuring that gas inlet pipe is fed through the hole at the rear bottom RHS of the heater. Refer figure 24 and gas connection figure 26. 12 d. Fix spacer to front frame with 7 s/t screws (provided). Refer fig 13. 24 13 14. With heater in position, flanges should be hard against masonry.
Installation instructions continued Installation into a fireplace. 5. Models FITZPIB & FITZPIBLP can be installed into a masonry/ brick fireplace or a mock fireplace. If installing into a mock fireplace a mock fireplace installation kit MUST be used. The mock fireplace kit can be ordered from the relevant service agent. Order specification for the part is ‘Mock kit”. 10.Disconnect the switch loom connector from the loom plug. Refer figure 20. 6. Prepare electrical and gas connections.
Installation instructions continued Installation into a fireplace. 5. Models FITZPIB & FITZPIBLP can be installed into a masonry/ brick fireplace or a mock fireplace. If installing into a mock fireplace a mock fireplace installation kit MUST be used. The mock fireplace kit can be ordered from the relevant service agent. Order specification for the part is ‘Mock kit”. 10.Disconnect the switch loom connector from the loom plug. Refer figure 20. 6. Prepare electrical and gas connections.
Installation instructions continued 11 20 c Assemble the spacer by fixing the two side sections to the top sections with a s/t screw (provided) each side. Refer figure 12. 23 13. Slide heater into the fireplace ensuring that gas inlet pipe is fed through the hole at the rear bottom RHS of the heater. Refer figure 24 and gas connection figure 26. 12 d. Fix spacer to front frame with 7 s/t screws (provided). Refer fig 13. 24 13 14. With heater in position, flanges should be hard against masonry.
Installation instructions Gas connections 1. This appliance is to be installed by a licensed service person only. 15. Connect incoming gas supply pipe to regulator. For inlet position see figure 26. Close gate over gas supply and seal around the pipe with fibreglass insulation material. Sealing is important as it prevents leakage from fan chamber into chimney: also check for gas soundness. 2.
Heater Specifications b) Place log No.2 onto the 2 left back pins. Refer figure 30. 30 c) Place log No.3 on single right front pin, ensure fork locates over log No. 2, see figure 31. Do not use fire with broken or missing logs. Gas type: Natural or Propane gas, as indicated on data label Gas consumption: 26 MJ/hr input Energy star rating: 3.77 Energy output: 20.7 MJ/hr Heater type: Heater approved to AS 4553/AG103. Operating pressure: Natural gas: 1.0 kPa Propane gas: 2.
Gas control User instructions continued Cleaning. All cleaning should be carried out when the heater is cold. Normally the heater should only need wiping with a lint - free damp cloth. Any stubborn stains can be removed with a non-abrasive spray on cleaner. If an abrasive cleaner is used the paint finish will be damaged. 23. Gas control layout is as indicated in figure 33.
Gas pressure adjustment 25. Switch the top two control buttons to “Full On” position as indicated in figure 36(a) and using a ring spanner, as per figure 36(b), adjust the pressure to 1kPa for Natural gas or 2.65 kPa for LPG. (Turn clockwise to increase pressure and anticlockwise to decrease pressure). 5. To increase the fan speed to MED, press switch for MED setting. Refer figure 5. 5 36 6. To increase the fan speed to HIGH, press switch for HIGH setting. Refer figure 6. 26.
User instructions Operating instructions Service Instructions 1. Plug the power cord into the wall socket and turn on the power to the heater, see figure 1. Refrain from using an extension cord. General 1. Service work to be carried out by a licensed service person only. 2. Unplug from wall socket or turn off power at main switchboard if heater is hard wired. 3. Always shut off the gas supply and ensure that the heater is cool before commencing any service operations. 4.
Troubleshooting 7. To check the operation of the electronic (module) controller (Type 537 ABC) you will require a digital multimeter with the functions to measure AC/DC voltage, continuity, resistance and micro-amps. 8. Installation and repairs should be performed by a licensed service person only, refer to back of brochure for service number. It is critical that the appliance is earthed and that the active and neutrals are not reversed. Item No Check Action 1 No ignition when appliance is turned on.
Safety Warnings Please read this manual before installing and using the heater. What to do if you smell gas 9 No gas to burner. • The gas valve should open at the same time as the igniter sparks. If there is no gas to the burner when this occurs check the solenoid coils for continuity. • Check that the gas pressure is present at the test point when the spark is being generated. • Check that there is gas to the inlet of the gas control. 10 Appliance lights but goes into lockout.
Warranty Wiring diagram The Cannon appliance is warranted against defects in materials and workmanship for a period of one, (1) year from its date of original purchase, for residential use in Australia. Warranty service, which includes parts and labour for the replacement or repair of defective parts, is available through Cannon Authorised Service Agencies. (Please refer to the list of authorised service agents in this manual.
Contents Contents 2 Warranty 3 Safety warnings 4-5 ❍ What to do if you smell gas ❍ Warnings ❍ Standards User instructions 6-8 ❍ Operating instructions ❍ Cleaning Heater specifications Installation instructions ❍ ❍ ❍ ❍ 9 10-14 Clearances Fitment of cabinet depth spacer Installation into a masonry fire place Sealing Gas connection 15-16 ❍ Fuel bed & log installation Gas control 17-18 ❍ Gas pressure point ❍ Gas pressure adjustment Service instructions ❍ ❍ ❍ ❍ ❍ ❍ 19 General To replace the gas
MAKER’S WARRANTY Cannon FITZROY PROFILE INBUILT MODELS FITZPIB, FITZPIBLP Cannon FITZROY PROFILE USER INSTRUCTIONS INSTALLATION INSTRUCTIONS SERVICE INSTRUCTIONS Part No: F2752 Revision B This heater is approved for use with Natural and Propane gases.