Specifications

ManualsBrandsCannon ManualsDomestic AppliancesFitzroy

Cannon

FITZROY INBUILT

USER INSTRUCTIONS

INSTALLATION INSTRUCTIONS

SERVICE INSTRUCTIONS

Gmk10025

AS4553:2008

This heater is approved for use with

Please leave instructions with the owner

Part No: F2903

Revision K - 2010

Cannon

For service to this appliance or spare

parts contact the CANNON distributor:

email: service@sampfordixl.com.au

Sampford IXL (spare parts)

Phone: 1300 727 421

Fax: 1300 727 425

Data label

FITZROY INBUILT

Natural and Propane gases.

Attach copy of data label here!

PLEASE READ THIS MANUAL

BEFORE INSTALLING AND

USING THIS HEATER.

DON’T RISK YOUR APPLIANCE WARRANTY

ONLY A LICENSED PERSON WILL GIVE YOU A COMPIANCE

CERTIFICATE, SHOWING THAT THE WORK COMPLIES WITH

ALL THE RELEVANT STANDARDS.

AND ONLY A LICENSED PERSON WILL HAVE INSURANCE

PROTECTING THEIR WORKMANSHIP FOR 6 YEARS.

SO MAKE SURE YOU USE A LICENSED PERSON TO INSTALL

THIS APPLIANCE AND ASK FOR YOUR COMPLIANCE

CERTIFICATE TO ENSURE THE MANUFACTURERS

APPLIANCE WARRANTY WILL BE HONOURED.

Date installed: ...............................................................................................

Compliance Certificate No .............................................................................

Installed by: ...................................................................................................

INSTALLATION NOTES

Summary of content (14 pages)

PAGE 1
INSTALLATION NOTES Cannon DON’T RISK YOUR APPLIANCE WARRANTY ONLY A LICENSED PERSON WILL GIVE YOU A COMPIANCE CERTIFICATE, SHOWING THAT THE WORK COMPLIES WITH ALL THE RELEVANT STANDARDS. FITZROY INBUILT AND ONLY A LICENSED PERSON WILL HAVE INSURANCE PROTECTING THEIR WORKMANSHIP FOR 6 YEARS. SO MAKE SURE YOU USE A LICENSED PERSON TO INSTALL THIS APPLIANCE AND ASK FOR YOUR COMPLIANCE CERTIFICATE TO ENSURE THE MANUFACTURERS APPLIANCE WARRANTY WILL BE HONOURED.
PAGE 2
Contents NOTES Contents 2 Warranty 3 ? Distributor Heater specifications 4 Safety warnings ? ? ? User instructions ? ? ? Electrical Connection Gas connections Gas control ? Gas pressure point ? Gas pressure adjustment Installation tips Trouble-shooting 2 14 15 16 17-18 19 20-21 Connections Service instructions ? ? ? ? ? ? ? ? ? ? ? ? ? 9 -13 Clearances Fitment of cabinet depth spacer Installation into a masonry/brick or mock fireplace Installation WITH a flue connected Installation WITHOUT
PAGE 3
NOTES Warranty The benefit conferred by this warranty are in addition to all other rights and remedies in respect of the product that consumers have under the Trade Practices Act and similar laws of the States and Territories. We warrant this Cannon appliance to be free of defects in materials, workmanship and manufacturing to the original purchaser for 2 years, (10 years on the heat exchanger) from the date of original purchase.
PAGE 4
Heater specifications YELLOW/GREEN BLK W ROOM FAN - F3594 BLUE WHITE BROWN BLACK N N BRN FUSE 1.5 AMP IGNITION MODULE F3434 BLUE BLUE RED 240 V MAINS PLUG RED E N A FLAME SENSOR BLUE YELLOW/GREEN BLACK SPARK ELECTRODE 4 WAY 1 BLUE L BLUE Note: The data label is located within the fan chamber (bottom heater cavity). Access by removing fascia. BROWN PURPLE GREY ORANGE RED installation kit must be used.
PAGE 5
Safety warnings Please read this manual before installing and using the heater. To remove the heat exchanger Please refer to manufacturer. Tel: 1300 727 421 To replace the burner and spark/sense electrodes 1. Remove the logs from the burner chamber. 2. Remove the burner chamber front inspection panel, 4 screws. 3. Disconnect the 16mm nut at the outlet of the gas control. 4. Disconnect the spark and sense electrodes from the ignition module (device). 5.
PAGE 6
8. If removed, the glass window must be put back onto the unit prior to operating the heater. To replace the room circulation fan 9. Installation and repairs should be performed by a licensed service person only, refer to back of the instructions for service number. 2. Remove the front screw retaining the bracket mounting the valve controls (white box). Move the bracket and controls to the front of the heater. 3. Disconnect the fan plug from the plug carrier.
PAGE 7
Service Instructions - (Do not modify this appliance) General Operating instructions 1. Service work to be carried out by an authorised service person only. 2. Unplug from wall socket or turn off power at main switchboard if heater is hard wired. 3. Always shut off the gas supply and ensure that the heater is cool before commencing any service operations. 4. Always check for gas soundness after servicing. To replace the primary glass 1.
PAGE 8
Cleaning All cleaning should be carried out when the heater is cold. Normally the heater should only need wiping with a lint-free damp cloth. Any stubborn stains can be removed with a non-abrasive spray on cleaner. If an abrasive cleaner is used the paint finish will be damaged. 8. Sparks, ignites on low flame then extinguishes after 10 seconds. Continues to spark during flame presence. ? Check that the wall socket to the appliance has 9. No gas to burner.
PAGE 9
Trouble-shooting - (Do not modify this appliance) To check the operation of the electronic (module) controller you will require a digital multimeter with the functions to measure AC/DC voltage, continuity, resistance and microamps. It is critical that the appliance is earthed and that the active and neutrals are not reversed. Item No Check 1. No ignition when appliance is turned on. Action ? Check 240 volt power to the heater in incoming plug connector. ? Check operation of room circulating fan.
PAGE 10
Installation tips For installation into a masonry or brick fireplace WITH a flue connection, refer figure 7. For installation WITHOUT refer figures 8 & 9. After installation of the heater test the flue to confirm air vents are unobstructed. If an exhaust fan or other heating/ventilation appliances are present, switch them on. This is to test and ensure that there is no interaction between the Cannon heater and other appliances.
PAGE 11
3. Switch the control buttons to ‘High flame’ position as indicated in figure 27 and using a spanner adjust the pressure to 0.75 kPa for Natural gas or 2.65 kPa for LPG. (Turn clockwise to increase pressure and anticlockwise to decrease pressure). Installation WITHOUT a flue connected Flue cowl. Approved to AG604 200mm min. 27 Fasten and seal baffle plate to top of chimney with waterproof mortar. Baffle plate 100mm 4. Switch the control buttons to ‘Low flame’ position as indicated in figure 28.
PAGE 12
Front Fascia removal Gas control 1. Remove the wire mesh grille by gently lifting it upwards and then outwards. Similarly remove a fitted glass kit by also gently lifting it upwards and then outwards. 2. Remove 4 M5 screws fixing the fascia assembly to the heater body. Bring the bottom of the fascia towards you gently to partly disengage it from the body of the heater. After it has been disengaged gently lift it up vertically to completely disengage it from the body of the heater. Refer figure 10. 1.
PAGE 13
Gas connections 1. Push the gas inlet access plate into the heater cabinet and slide the heater into the fireplace ensuring that the gas inlet pipe is fed through the hole located at the rear right hand side of the heater at the bottom. Refer to figure 21 and connection dimensions in figure 23. Sealing the Fascia All gaps between heater case and fireplace are to be sealed. Seal with foam tape around top and sides of heater flange. Refer figure 13.
PAGE 14
Electrical Connection Log installation 1. The burner is contained within the burner chamber. Refer figure 15. 2. Carefully unpack the log set. Logs are numbered as follows: #1 - Left front log #2 - Left back log #3 - Right front log #4 - Right back log This appliance is designed to operate on 240V AC power supply. Failure to operate unit at correct supply voltage may created unsafe conditions.