Specifications

ManualsBrandsCannon ManualsDomestic AppliancesFitzroy

Table Of Contents

Power Flue

Cannon

FITZROY INBUILT

OPERATION INSTRUCTIONS

SERVICE INSTRUCTIONS

Gmk10030

AS4553:2008

This heater is approved for use with

Please leave instructions with the owner

Part No: F3045

Revision P - 2010

Cannon

For service to this appliance or spare

parts contact the CANNON distributor:

email: service@sampfordixl.com.au

Sampford IXL (spare parts)

Phone: 1300 727 421

Fax: 1300 727 425

FITZROY INBUILT

Natural and Propane gases.

DON’T RISK YOUR APPLIANCE WARRANTY

ONLY A LICENSED PERSON WILL GIVE YOU A COMPIANCE

CERTIFICATE, SHOWING THAT THE WORK COMPLIES WITH

ALL THE RELEVANT STANDARDS.

AND ONLY A LICENSED PERSON WILL HAVE INSURANCE

PROTECTING THEIR WORKMANSHIP FOR 6 YEARS.

SO MAKE SURE YOU USE A LICENSED PERSON TO INSTALL

THIS APPLIANCE AND ASK FOR YOUR COMPLIANCE

CERTIFICATE TO ENSURE THE MANUFACTURERS

APPLIANCE WARRANTY WILL BE HONOURED.

Power Flue

Date installed: ...............................................................................................

Compliance Certificate No .............................................................................

Installed by: ...................................................................................................

INSTALLATION NOTES

PLEASE READ THIS MANUAL

BEFORE INSTALLING

THIS HEATER.

COPY RATING LABEL HERE

INSTALLATION INSTRUCTIONS

The Cannon appliance is warranted against defects in materials and

Warranty service, which includes parts and labour for the replacement or

repair of defective parts, is available through the CANNON distributor.

(Details below or on page 24).

Consumers are responsible for service person’s travel outside normal

service areas (approximately seventy (70) kilometer radius from the nearest

Cannon dealer’s location), local transport costs, or any preventative

maintenance works as described in

Any product subjected to misuse, abuse, negligence, accident or alteration

will have its warranty voided. The defacement of serial plate will also void

warranty.

If installation is not carried out in accordance with manufacturer’s

instructions, this warranty may be void.

The customer must keep their “Tax Invoice” as proof of purchase of this

product and compliance certificate as proof of required installation.

workmanship for a period of two (2) years from its date of original

purchase, applicable only for residential use in Australia.

this manual.

Enter the details of the date installed and the Compliance Certificate

number in the appropriate area on the rear page of this manual.

Summary of content (14 pages)

PAGE 1
INSTALLATION NOTES Cannon DON’T RISK YOUR APPLIANCE WARRANTY ONLY A LICENSED PERSON WILL GIVE YOU A COMPIANCE CERTIFICATE, SHOWING THAT THE WORK COMPLIES WITH ALL THE RELEVANT STANDARDS. FITZROY INBUILT AND ONLY A LICENSED PERSON WILL HAVE INSURANCE PROTECTING THEIR WORKMANSHIP FOR 6 YEARS. SO MAKE SURE YOU USE A LICENSED PERSON TO INSTALL THIS APPLIANCE AND ASK FOR YOUR COMPLIANCE CERTIFICATE TO ENSURE THE MANUFACTURERS APPLIANCE WARRANTY WILL BE HONOURED.
PAGE 2
CONTENTS NOTES Contents 2 Warranty ? Distributor Heater specifications 3 Safety warnings ? What to do if you smell gas ? Warnings ? Standards ? Regulatory location User instructions ? Operating instructions ? Cleaning ? Flame characteristics Installation instructions ? ? ? ? ? ? ? 4 5-6 7 8-9 10 -13 Clearances Fitment of cabinet depth spacer Flueing options Fitment of flue cowl Preparing flexible flue pipes Front fascia removal Sealing the fascia Electrical Connection Gas connections Log installat
PAGE 3
NOTES WARRANTY The benefit conferred by this warranty are in addition to all other rights and remedies in respect of the product that consumers have under the Trade Practices Act and similar laws of the States and Territories. We warrant this Cannon appliance to be free of defects in materials, workmanship and manufacturing to the original purchaser for 2 years, (10 years on the heat exchanger) from the date of original purchase.
PAGE 4
YELLOW/GREEN BLUE COILS ROOM FAN - F3594 WHITE BROWN BLUE BLK W BRN BROWN RED BLACK PURPLE GREY FUSE 1.5 AMP BLUE 240 V MAINS PLUG POWER FLUE WIRING DIAGRAM F3663-6_B RED BLUE YELLOW/GREEN E N A PRESSURE SWITCH F3327 ROOM AIR FAN NO NO COMMON IGNITION MODULE F3435 4 WAY SPARK ELECTRODE FLAME SENSOR PRESSURE SWITCH F3327 COMBUSTION FAN MODULATING VALVE F3691 COMBUSTION FAN - F3659 4 WAY COMMON ORANGE FIG 1.
PAGE 5
SERVICE INSTRUCTIONS notes SAFETY WARNINGS Please read this manual before installing and using the heater. TO REMOVE THE BURNER AND ELECTRODES 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. TO REPLACE THE COMBUSTION FAN Remove the front mesh cover. Slacken off the glass clamp screws and remove the top and one side clamp. Follow fig 25. of the installation instructions for glass removal. Remove the logs from the burner chamber. Remove the inspection hatch cover. Disconnect supply pipe nut from the burner manifold.
PAGE 6
SAFETY WARNINGS 8. If removed, the glass window must be put back onto the unit prior to operating the heater. 9. Installation and repairs should be performed by a licensed service person only, refer to back of the instructions for service number. 10. For installation into a non-combustible fireplace, i.e.: masonry or brick or into a mock fireplace, i.e.
PAGE 7
SERVICE INSTRUCTIONS - (DO NOT MODIFY THIS APPLIANCE) REGULATORY LOCATION General 1. Service work to be carried out by an authorised service person only. 2. Unplug from wall socket or turn off power at main switchboard if heater is hard wired. 3. Always shut off the gas supply and ensure that the heater is cool before commencing any service operations. 4. Always check for gas soundness after servicing. FIG 2.
PAGE 8
TROUBLESHOOTING USER INSTRUCTIONS Operating instructions FIG 3. 5 Confirm spark is produced when heater is turned on. 6 If no spark being produced. Plug the power cord into the wall socket and turn on the power to the heater (see figure 3). Refrain from using an extension cord. Alternatively, switch on the isolation switch and circuit breaker at the main switchboard if the heater has fixed wiring.
PAGE 9
TROUBLESHOOTING-(DO NOT MODIFY THIS APPLIANCE) To check the operation of the electronic (module) controller (Techrite) you will require a digital multimeter with the functions to measure ac / dc voltage, Continuity, resistance and micro-amps. It is critical that the appliance is earthed and that the active and neutral are not reversed. Trouble shooting Guide for Ignition Controller ( Techrite) There is a greeen and red LED on the ignition controller.
PAGE 10
INSTALLATION DETAIL INSTALLATION DETAIL 3. Switch the control buttons to ‘High flame’ position as indicated in figure 26 and using a screwdriver held in position adjust spanner to the pressure 0.75 kPa for Natural gas or 2.65 kPa for LPG. (Turn clockwise to increase pressure and anticlockwise to decrease pressure). 1. This appliance is to be installed by an authorised service person only. 2.
PAGE 11
GAS CONTROL FLUEING OPTIONS 23. Gas control layout is as indicated in figure 23. The heater is supplied with components to suit a horizontal flue coming through a wall at the back of the heater. The Components include a flue cowl which is designed to be fitted to the outside wall with suitable fasteners. Condensate drain tube 2m and Clamp, and flexible tube sealant.
PAGE 12
INSTALLATION DETAIL INSTALLATION DETAIL CAVITY REQUIREMENTS The heater is to be fitted into position with the flue pipes fully installed onto the heater. Therefore, the cavity must be prepared to accept the heater first. Before cutting any flue opening in the external wall, the finished floor level must be known. This floor level must include any tiling, loose hearth or panels which will support the heater. All clearances shown in fig 1. & fig 2. must be adhered to.
PAGE 13
INSTALLATION DETAIL INSTALLATION DETAIL 695 mm 160 DIA FLUE OPENING Bend gas pipe and electrical entry tags inwards to allow cable and gas pipe to enter easily. FIG 10. Fully extend the flexible flue and air intake and position these pipes through the hole driled through the wall. Route condensate tube through smaller hole in wall. FIG 17. 20 DIA CONDENSE DRAIN HOLE 345 mm SEALING TAPE APPLIED TO EDGE OF UNIT BEFORE POSITIONING.
PAGE 14
LOG INSTALLATION FRONT FASCIA REMOVAL 1. Remove the wire mesh grille by gently lifting it upwards and then outwards. Similarly remove a fitted glass kit by also gently lifting it upwards and then outwards. Carefully unpack the log set. Logs are numbered as follows: no1 left front no2 left back no3 right front no4 right back log. 2. Remove 4 M5 screws fixing the fascia assembly to the heater body. Bring the bottom of the fascia towards you gently to partly disengage it from the body of the heater.