INTELLITROLL SPEED-N-TEMP MONITOR Owner’s Manual
Serial Number: _____________________________________ Purchase Date: _____________________________________ Store Where Purchased: ______________________________
INTRODUCTION Congratulations on your purchase of the Cannon® IntelliTroll Depth, Temperature and Speed monitoring system. The probe unit and display use Cannon’s advanced underwater sensing technology to give you the most complete trolling information ever.
DISPLAY INSTALLATION (cont.) Here are a few tips: • Avoid mounting the display near 2 way radios and antennas as this can cause interference with probe operation. • If the mounting surface is made from thin fiberglass, a piece of wood underneath the fiberglass will help secure the bracket. • Before drilling any holes for the bracket be sure to double check that no cables or hoses are near the exit point of the drill bit. • When mounting the monitor to the boat consider rough water conditions.
DISPLAY INSTALLATION (cont.) To add an inline connector to your IntelliTroll system follow this procedure: You will need one each of the following Cannon components: • p/n 3397505 antenna cable (included with IntelliTroll system) • p/n 3887510 antenna extension cable • p/n 3882710 replacement antenna kit NOTE: Be sure to read and understand all instructions before cutting any wires. 1.
DISPLAY INSTALLATION (cont.) current failures. You can attach the power cable to the boat accessory panel, however you may experience undesirable electrical interference if you do so. Connect the cable to the battery as follows: Red wire to positive (+) terminal. Black wire to negative (-) terminal. • Connecting the monitor to the same circuit as other devices such as tachometers, radios, or trim switches may cause electrical interference.
DISPLAY INSTALLATION (cont.) Step 5: Install the Coated Downrigger Cable NOTE: The coated cable may make certain spool-mounted cable counters inaccurate due to the difference in cable diameters. The supplied cable may produce up to a 30% error on your counter. For example, if your counter reads 100 feet the actual amount of cable out would be approximately 130 feet. With the IntelliTroll, however, you still have the benefit of knowing the true depth of the ball and bait.
PROBE INSTALLATION (When using the IntelliTroll Monitor) Installing the Battery Unscrew the back cover of the probe module and remove the plastic battery pack holder. Install 4 high quality Alkaline AA batteries into the battery pack. When inserting the battery pack into the probe be sure that the snap terminals on the battery pack align with the spring contact inside the probe.
PROBE INSTALLATION (cont.) Installing Probe on the Downrigger cable To prevent losing the probe overboard it is recommended that the safety lanyard clasp be installed first. Open the clasp hook and place around the downrigger wire. Next loosen the thumb screw at the front end of the probe assembly so the cap slides back enough to slip the uncoated portions of the cable under the cover. Adjust the location of the probe on the downrigger line and tighten the thumb screw.
PROBE INSTALLATION (cont.
PROBE INSTALLATION (cont.
PROBE INSTALLATION (When NOT using the IntelliTroll Monitor) Both the Digi-Troll 5 and Digi-Troll 10 downriggers are compatible with the IntelliTroll accessory. The Digi-Troll 5 receives the IntelliTroll data and displays it on your Humminbird fish finder through Cannonlink* or the Intellitroll monitor. The Digi-Troll 10 displays IntelliTroll data directly on the LCD screen on the downrigger. To install the Intellitroll on the Digi-Troll follow the steps below: 1. Install battery (see page 5) 2.
PROBE INSTALLATION (cont.) 4. With a 1/4” wrench, loosen the bolt and remove. 5. Install the antenna spring that came with the Intellitroll sensor kit. Insert bolt into the closed loop on the spring.
PROBE INSTALLATION (cont.) 6. Tighten bolt. Caution: Do not over tighten as the stainless steel bolt head may shear with too much torque. 7. Once the antenna is installed, run downrigger cable through center of spring.
PROBE INSTALLATION (cont.) 8. Terminate cable as previously described. Your Digi-Troll is now Intellitroll compatible. Once you attach your Intellitroll to the cable per the instructions included, your Digi-Troll 10 will display the data on it’s screen. The Digi-Troll 5 will pass this data on to the Cannonlink for display on your Humminbird fish finder.
SYSTEM OPERATION On / Off of Probe There is no on / off switch for the IntelliTroll Probe. The probe automatically turns on when placed in the water. The probe will automatically turn off when 2 conditions exist: The probe is removed from the water and the speed wheel stops spinning for 60 seconds. Once the Probe is placed in the water and the display is turned on data will become visible on the monitor.
SYSTEM OPERATION (cont.) Setup Items 1. Back Light (default off) • The back light will help make the display information visible in low light conditions. 2. Display Contrast (default 3) • Contrast is the darkness or brightness of the display. Both your viewing angle and the ambient temperature affect the desired contrast level. 3. Depth Alarm (default 250ft) • The depth alarm can be used to signal you that the probe has exceeded the maximum depth. The default is 250ft.
SYSTEM OPERATION (cont.) On / Off of Display As mentioned previously, the display can be turned on by pressing the POWER/ MENU button. Once the display is on select the REAL mode and press POWER/MENU. At this point data from the probe can now be received. To turn off the display push and hold the POWER/MENU button for 4 seconds. Normal Operation Once the system is powered data will be shown on the display. As Depth, Speed or Temp of the probe changes the display will automatically update the data.
SPECIFICATIONS Monitor diagonal: Monitor resolution: Monitor power consumption: Monitor Voltage requirements: Probe battery requirements: Probe battery life: 4 inches 160V x 128H 25mA with backlight off 55mA with backlight on 9-14VDC 4AA Greater than 200 hours of run time FAQ Display will not turn on: 1. Verify that power is connected to the display and that the fuse is good. 2. Verify source voltage. The display will function on 9VDC to 14VDC.
FAQ (cont.) Water in transmitter: 1. Water should not be in the transmitter. The O-ring seal design has been tested well beyond the limits of practical fishing. If you find water in the probe follow these steps or you risk permanent damage to the probe. 1. Remove the batteries from the probe and discard them in the appropriate manner. If the probe leaked due to high pressure water may have penetrated the batteries and will cause them to leak acid in a short amount of time. 2.
FAQ (cont.) No data is displayed when the trolling motor is turned on: 1. All electronic devices transmit unwanted signals. The receiver (monitor display) is a sensitive electronic radio system. Strong RF signals can interfere with the operation of the IntelliTroll. 2. Verify that the antenna and antenna cable are not in close proximity to larger motors or other radio communication equipment. 3.
20 60 90 100 70 40 80 95 110 120 50 10 135 140 20 30 5 260 200 130 250 270 280 210 290 PARTS DIAGRAM
PARTS LIST In the U.S.A., replacement parts may be ordered directly from CANNON Parts Dept., 121 Power Dr., Mankato, MN 56661. In Canada, parts may be ordered from any of the Canadian Authorized Service Centers. Visit cannondownriggers.com for a current listing. Be sure to provide the MODEL and SERIAL numbers of your downrigger when ordering parts. Please use the correct part numbers from the parts list.
LIMITED WARRANTY Johnson Outdoors Marine Electronics, Inc. warrants to the original purchaser that if the accompanying product (see exclusions below) proves to be defective in material or workmanship within the following warranty periods, Johnson Outdoors Marine Electronics, Inc.
SERVICE POLICY AFTER THE APPLICABLE WARRANTY PERIOD After the applicable warranty period, or, if one of the above exclusions applies, Cannon® products will be repaired for a charge of parts plus labor. All factory repairs, after the applicable warranty period, carry a 90-Day Limited Warranty, subject to the exclusions and limitations stated above. TO ENFORCE WARRANTY OR TO OBTAIN REPAIRS AFTER WARRANTY To obtain warranty service in the U.S.
ENVIRONMENTAL COMPLIANCE STATEMENT (cont.) most distributors, sellers, and manufacturers of consumer electronics in the European Union. The WEEE Directive requires the producer of consumer electronics to take responsibility for the management of waste from their products to achieve environmentally responsible disposal during the product life cycle.
Consumer & Technical Service Johnson Outdoors Marine Electronics, Inc. PO Box 8129 121 Power Drive Mankato, MN 56001 Phone (800) 227-6433 Fax (800) 527-4464 cannondownriggers.com Copyright 2009 Johnson Outdoors Marine Electroincs, Inc. All rights reserved. Conforms to 89/336/EEC (EMC) under standards EN 55022A, EN 50082-2 since 1996 LN V9677264 WARNING: This product contains chemical(s) known to the state of California to cause cancer and/or reproductive toxicity.
