EdgeAccess Universal Chassis System ® Model 6002, 6003, 6004 Unidirectional Widely Spaced Wavelength Division Multiplexer (WWDM) Users Manual
® EdgeAccess Universal Chassis System Caution! This product is a passive device that may route light emitted by a laser diode operating at a wavelength of 1300nm - 1600nm. Use of optical instruments (for example: collimating optics) with this product may increase eye hazard. Use of controls or adjustments or performing procedures other than those specified herein may result in hazardous radiation exposure.
® EdgeAccess Universal Chassis System NOTICE Canoga Perkins has prepared this user manual for use by customers and Canoga Perkins personnel as a guide for the proper installation, operation and/or maintenance of Canoga Perkins equipment. The drawings, specifications and information contained in this document are the property of Canoga Perkins and any unauthorized use or disclosure of such drawings, specifications and information is prohibited.
® EdgeAccess Universal Chassis System ® Canoga Perkins EdgeAccess Universal Chassis System (UCS) Model 6002, 6003, 6004 (6002/3/4) Unidirectional Widely Spaced Wavelength Division Multiplexer (WWDM) iv 6002/6003/6004 WWDM Users Manual
® EdgeAccess Universal Chassis System Table of Contents Chapter 1 General Overview ......................................................................... 1-1 1.1 Overview.............................................................................................. 1-1 1.2 Stand Alone 6002/3/4 Models.............................................................. 1-2 1.3 Rack Mount 6002/3/4 Models .............................................................. 1-2 Chapter 2 Set-up and Installation ........
® EdgeAccess Universal Chassis System Appendix A Warranty A.1 Warranty .............................................................................................. A-1 A.1.1 Electronic Products.............................................................................. A-1 A.1.2 Cable Products .................................................................................... A-1 A.1.3 Limitations............................................................................................ A-2 A.
® EdgeAccess Universal Chassis System Chapter 1 General Overview 1.1 Overview EdgeAccess® Models 6002, 6003, 6004 (6002/3/4) are passive, unidirectional Widely spaced Wavelength Division Multiplexers (WWDM) that fit into the EdgeAccess Universal Chassis System (UCS), or a stand alone enclosure. The WWDM multiplexes (MUX) two to four optical signals onto a single composite signal for transmission to a remote location.
® EdgeAccess Universal Chassis System 1.2 Stand Alone 6002/3/4 Models The 6002/3/4 stand alone models are passive, non-powered devices. The models have no user configurable switches and require no management aware connections. Because these models have no electrical components, they can fit easily into multiple environments. The stand alone Model 6000 Optical Multiplexer shown in Figure 2, represents the 6002/3/4 stand alone (SA) series. Figure 2. Model 6000 Series of Devices Stand Alone Module 1.
® EdgeAccess Universal Chassis System Chapter 2 Set-up and Installation 2.1 Unpacking and Installing the Stand Alone Models Each stand alone 6002/3/4 is factory tested and shipped in protective cartons. After unpacking the unit and its accessories, retain the shipping carton and protective packing material in the event a need arises in which the equipment must be returned to the factory. SA models can be installed on any desktop, shelf, or mounted in a rack with the optional rack mount bracket kit.
® EdgeAccess Universal Chassis System 2.4 Cabling The 6002/3/4 models are passive, unidirectional wavelength division multiplexers. Each module allows simultaneous transmission of two to four optical signals over a single fiber pair. 2.4.1 Fiber Optic Cabling Optical cabled devices transmit (Tx) and receive (Rx) channel-to-channel signals through local and remote modules. All fiber optic cables should be properly connected using the Tx to Rx, or Rx to Tx orientation.
® EdgeAccess Universal Chassis System 2.4.4 Checking Optical Power Levels Each 6002/3/4 model is shipped with a document that lists the specific output power for each local and remote laser. To ensure proper optical performance levels, the link loss or attenuation of all fiber cables should be measured and identified. Determine the link attenuation by using a 1310/1550nm laser source. Either a hand-held or other similar measuring device can be used.
® EdgeAccess Universal Chassis System 2.4.6 Measuring Receiver Input Power If the link attenuation is not known, the Model 6002/3/4 can be used to measure the link loss or attenuation. If the link attenuation is already known – skip this section. To measure the link attenuation: Step 1 At the local site, connect the remote fiber link cable to the remote Tx connector on the 6002/3/4 model. Note: Prior to measuring input power, let the units warm up for at least 30 minutes.
® EdgeAccess Universal Chassis System Chapter 3 User Operation 3.1 WWDM Application WWDM (widely spaced wavelength division multiplexer) models multiplex and demultiplex wavelengths in the 1310nm, 1480nm, and 1550nm windows, and are protocol, speed, and line code transparent. Each 6002/3/4 model is unidirectional (meaning that light travels in only one direction on a fiber line) and transmits signals through a composite pair of single mode fibers.
® EdgeAccess Universal Chassis System 3.2 Operation of the Stand Alone Models To ensure proper optical performance levels, you will need to determine the loss budget. This factor will ensure link integrity and ample signal strength at the remote end of your link. To operate the 6002 stand alone model: Step 1 Measure each of the optical composite fiber links at the lowest wavelength of operation. This will determine the limiting factor in the loss budget.
® EdgeAccess Universal Chassis System 3.3 Operation of the Rack Mount Models When the 6002/3/4 RM module is installed into the EdgeAccess Universal Chassis System, a “STA” or status LED on the front panel will illuminate amber. This test signal from the UCS verifies that a backplane connection was established. A red light indicates a connection error. When the 6002/3/4 LED illuminates green, the light indicates: • • • The module is properly seated in the UCS slot.
® EdgeAccess Universal Chassis System This Page is Intentionally Left Blank 3-4 6002/6003/6004 WWDM Users Manual
® EdgeAccess Universal Chassis System Chapter 4 Software Interaction 4.1 Universal Chassis System Software When the rack mount 6002/3/4 models are properly installed in a managed UCS 1000 Chassis, the DMM module will open the required HyperTerminal™ software. The computer application will display the screenshots shown in this section. Note: For additional HyperTerminal access instructions refer to the DMM Users Manual.
® EdgeAccess Universal Chassis System The DMM will show that two Model 6002-LightWave Modules are inserted into Chassis 1 on the LOCAL UCS. The Status of Slots 4 & 5 will show OK. Figure 9. Chassis Management Screen Showing Inserted Modules To access inserted modules from the UCS DMM Chassis Management screen: • • • • • Press the SPACE BAR to move the cursor to the desired Slot number (refer to Figure 9). When the selected Slot number 4 is highlighted, press the CR (Carriage Return / Enter key).
® EdgeAccess Universal Chassis System 4.2 Naming the WDM module in a Chassis Configuration In many applications, it may be beneficial to name the WDM module in the UCS Chassis or the circuit path that it is part of. This identification feature is useful to name the circuit designations of all connected modules. When multiple customers are serviced with a single 6002/3/4 module, a customer name can be included for effective system management.
® EdgeAccess Universal Chassis System Naming the Chassis / Slot number of the installed module: • • • The Module Menu screen will appear, note the example in Figure 12 shows that the 6002LightWave module is inserted into Chassis 1, Slot 4. Choose number 1, or “Name the module”, then press . Type in the desired new name at the “Enter new name” prompt line, note the example shows “Canoga Perkins-2” as the entered name.
® EdgeAccess Universal Chassis System Chapter 5 Troubleshooting and Maintenance 5.1 Troubleshooting Fiber Optic Cables All optical cables should be connected using a Tx to Rx, or Rx to Tx orientation for correct MUX and DEMUX signal operation. Proper labeling of each connecting cable is highly recommended. 5.2 Troubleshooting Guide The 6002/3/4 models are passive, unidirectional WWDMs. The modules provide simultaneous transmission of two to four optical signals over a composite SMF pair.
® EdgeAccess Universal Chassis System 5.3 Maintenance The Model 6002/3/4 is designed to perform at specified performance levels. Damaged fiber cables and dirty connectors are a common source of signal loss or link attenuation. Single mode optical fibers should be checked frequently. Inspect and test all suspect components to maintain optimal system performance levels. As a rule, whenever there is a significant, unexplained light loss, check the fiber cable and the connectors for potential problems.
® EdgeAccess Universal Chassis System Chapter 6 Specifications 6.1 Single Mode Specifications 6.1.1 Local Channels Data Rate: Protocols: Fiber: Optical Connector: Speed transparent All, no limitation Single mode (SMF) ST, FC/PC, or SC Duplex APC connectors (special order) 6.1.2 Remote Channels Composite Data Rate: Protocols: Fiber: Optical Connector: Speed transparent All, no limitation Single mode (SMF) ST, FC/PC, or SC Duplex APC connectors (special order) 6.1.
® EdgeAccess Universal Chassis System 6.2 WWDM Model Specifications The Model 6002/3/4 is available in a variety of user-specified wavelengths and loss budget configurations. All end-to-end loss calculations were figured at maximum loss values. Note: Actual attenuation loss values should be used when computing final loss budgets. Basic channel features and wavelengths are defined in Tables 2 through 4. The model type options for fused or filtered fiber applications are noted. 6.2.
® EdgeAccess Universal Chassis System 6.2.2 Unidirectional Three Channel WWDM The Model 6003 is a three channel unidirectional module with various wavelength configurations. Table 3 shows current available model options. Table 3. Unidirectional Three Channel WWDM Chart MODEL NUMBER MODEL TYPE WAVELENGTH Nanometers (nm) END-TO-END LOSS (dB) DIRECTIVITY (dB) ISOLATION (dB) 6003 FUSED * or FILTER 1310 / 1480 / 1550 1.5 (1310) 3.0 (1480) 2.
® EdgeAccess Universal Chassis System This Page is Intentionally Left Blank 6-4 6002/6003/6004 WWDM Users Manual
® EdgeAccess Universal Chassis System Appendix A Warranty A.1 Warranty A.1.1 Electronic Products Canoga Perkins warrants to the Customer that all goods sold to the Buyer will perform in accordance with the applicable data sheets, drawings or written specifications, and at the time of sale will be free of defects in material and workmanship. The warranty period for OSP test equipment shall be ONE (1) YEAR from the date of shipment.
® EdgeAccess Universal Chassis System A.1.3 Limitations Other than those expressly stated herein, THERE ARE NO OTHER WARRANTIES OF ANY KIND, EXPRESSED OR IMPLIED, AND SPECIFICALLY EXCLUDED BUT NOT BY WAY OF LIMITATION, ARE THE IMPLIED WARRANTIES FOR FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY.
® EdgeAccess Universal Chassis System A.4 Extended Warranty Policy Canoga Perkins will, at its factory location, repair all defects occurring in Canoga Perkins products for a period of one year after the expiration of the original three-year factory warranty for a fee equal to six (6) percent of the current list price of the product. The product must be placed under extended warranty by written order from the customer and may be renewed for up to three years beyond the original extension.
