E INSTRUCTION MANUAL
Introduction The EOS 5DS/EOS 5DS R is a digital single-lens reflex camera featuring a full-frame CMOS sensor (approx. 36.0 mm x 24.0 mm) with approx. 50.6 effective megapixels, Dual DIGIC 6, approx. 100% viewfinder coverage, high-precision and high-speed 61-point AF, approx. 5.0 fps continuous shooting, 3.2-inch LCD monitor, Live View shooting, and Full High-Definition (Full HD) movie shooting.
Item Check List Before starting, check that all the following items are included with your camera. If anything is missing, contact your dealer. Eyecup Eg Camera (with body cap) Wide Strap Battery Charger Battery Pack LP-E6N LC-E6/LC-E6E* (with protective cover) Interface Cable IFC-150U II Cable protector * Battery Charger LC-E6 or LC-E6E is provided. (The LC-E6E comes with a power cord.) The Instruction Manual and CD-ROMs provided are listed on the next page.
Instruction Manual and CD-ROMs The instruction manual consists of a booklet, a leaflet, and electronic manuals (PDF files on the CD-ROM). Camera Basic Instruction Manual Quick Reference Guide Camera Instruction Manual CD-ROM Contains the following manuals (PDF files): • Camera Instruction Manual (Detailed version) • Quick Reference Guide Instructions for viewing the Camera Instruction Manual CD-ROM are on pages 516-517.
Compatible Cards The camera can use the following cards regardless of capacity: If the card is new or was previously formatted (initialized) by another camera or computer, format the card with this camera (p.67). CF (CompactFlash) cards * Type I, UDMA mode 7-compatible. SD/SDHC*/SDXC* memory cards * UHS-I cards supported. Cards that Can Record Movies When shooting movies, use a large-capacity card with a fast reading/ writing speed as shown in the table. Movie Recording Size (p.
Quick Start Guide 1 2 Insert the battery (p.42). To charge the battery, see page 40. Insert the card (p.43). The camera-front side slot is for a CF card, and the camera-back side slot is for an SD card. * Shooting is possible with either a CF card or an SD card in the camera. 3 Attach the lens (p.52). 4 Set the lens’s focus mode switch to (p.52). 5 Set the power switch to <1> (p.47). 6 Align it with the red dot.
Quick Start Guide 6 While holding down the center of the Mode Dial, set it to (Scene Intelligent Auto) (p.33). All the necessary camera settings will be set automatically. 7 Focus on the subject (p.55). 8 Take the picture (p.55). 9 Review the picture. Look through the viewfinder and aim the viewfinder center over the subject. Press the shutter button halfway, and the camera will focus on the subject. Press the shutter button completely to take the picture.
Conventions Used in this Manual Icons in this Manual <6> <5> <9> <0> 0/9/4/7/8 : : : : : Indicates the Main Dial. Indicates the Quick Control Dial. Indicates the Multi-controller. Indicates the Setting button. Indicates that each function remains active for 4 sec., 6 sec., 8 sec., 10 sec., or 16 sec. after you let go of the button. * In this manual, the icons and markings indicating the camera’s buttons, dials, and settings correspond to the icons and markings on the camera and on the LCD monitor.
Chapters For first-time DSLR users, Chapters 1 and 2 explain the camera’s basic operations and shooting procedures.
Contents Introduction 2 Item Check List................................................................................. 3 Instruction Manual and CD-ROMs ................................................... 4 Compatible Cards............................................................................. 5 Quick Start Guide ............................................................................. 6 Conventions Used in this Manual..................................................... 8 Chapters.............
Contents l Displaying the Grid. .................................................................. 74 Q Displaying the Electronic Level ...............................................75 Setting the Viewfinder Information Display .....................................77 Help .......................................................................................... 78 2 Basic Shooting 79 A Fully Automatic Shooting (Scene Intelligent Auto) ...................
Contents A Registering a Picture Style ................................................... 172 B: Setting the White Balance ................................................... 174 O Custom White Balance........................................................ 176 P Setting the Color Temperature ............................................ 178 u White Balance Correction ....................................................... 179 Auto Correction of Brightness and Contrast.................................
Contents Using the Eyepiece Cover ............................................................ 236 F Using a Remote Switch............................................................. 237 R Remote Control Shooting...........................................................237 H Interval Timer Shooting ...................................................... 239 6 Flash Photography 243 D Flash Photography .................................................................... 244 Setting the Flash ...........
Contents 9 Image Playback 319 x Image Playback ..................................................................... 320 B: Shooting Information Display ............................................ 322 x Searching for Images Quickly ................................................ 327 H Display Multiple Images on One Screen (Index Display)..... 327 I Jump through Images (Jump Display).................................. 328 u Magnifying Images...............................................................
Contents 11 Sensor Cleaning 373 f Automatic Sensor Cleaning................................................... 374 Appending Dust Delete Data ........................................................375 Manual Sensor Cleaning...............................................................377 12 Printing Images and Transferring Images to a Computer 379 Preparing to Print .......................................................................... 380 w Printing ...........................................
Contents 14 Reference 441 B Button Functions ................................................................ 442 Checking the Battery Information ................................................. 446 Using a Household Power Outlet ................................................. 450 H Using Eye-Fi Cards................................................................. 451 System Map .................................................................................
Index to Features Power LCD Monitor Charging the battery Î p.40 Brightness adjustment Î p.361 Battery level Î p.48 Electronic level Î p.75 Help Î p.78 Battery information check Î p.446 Household power outlet Î p.450 Auto power off Î p.69 Card AF AF operation Î p.86 AF area selection mode Î p.90 AF point selection Î p.93 Formatting Î p.67 AF point registration Î p.418 Recording function Î p.146 Lens group Î p.100 Selecting card Î p.148 AF points lighting up in red Î p.
Index to Features Image Quality Exposure Image-recording quality Î p.149 Exposure compensation Î p.214 Crop/aspect ratio Î p.154 ISO speed Î p.158 Exposure compensation with M+Auto ISO Î p.211 Picture Style Î p.164 AEB Î p.215 White balance Î p.174 AE lock Î p.217 Safety shift Î p.405 Auto Lighting Optimizer Î p.182 Noise reduction for high ISO speeds Flash Î p.183 External Speedlite Î p.244 Noise reduction for long exposures Î p.185 Flash exposure compensation Î p.
Index to Features Movie Shooting Image Editing Movie shooting Î p.279 RAW image processing Î p.364 AF method Î p.268 Resizing JPEGs Î p.369 Movie Servo AF Î p.313 Cropping JPEGs Î p.371 Movie recording quality Î p.297 Printing and Transferring Images Sound recording Î p.300 Time code Î p.303 PictBridge Î p.379 Time-lapse movie Î p.306 Print Order (DPOF) Î p.389 Still photo shooting Î p.293 Image transfer Î p.393 Photobook Set-up Î p.
Safety Precautions The following precautions are provided to prevent harm or injury to yourself and others. Make sure to thoroughly understand and follow these precautions before using the product. If you experience any malfunctions, problems, or damage to the product, contact the nearest Canon Service Center or the dealer from whom you purchased the product. Warnings: Follow the warnings below. Otherwise, death or serious injuries may result.
Safety Precautions When the camera or accessories are not in use, make sure to remove the battery and disconnect the power plug from the equipment before storing. This is to prevent electrical shock, excessive heat, fire, or corrosion. Do not use the equipment where there is flammable gas. This is to prevent an explosion or a fire. If you drop the equipment and the casing breaks open to expose the internal parts, do not touch the internal parts. There is a possibility of an electrical shock.
Safety Precautions Cautions: Follow the cautions below. Otherwise, physical injury or property damage may result. Do not use or store the product inside a car under the hot sun or near a heat source. The product may become hot and cause skin burns. Doing so may also cause battery leakage or explosion, which will degrade the performance or shorten the life of the product. Do not carry the camera around when it is attached to a tripod. Doing so may cause injury.
Handling Precautions Camera Care This camera is a precision instrument. Do not drop it or subject it to physical shock. The camera is not waterproof and cannot be used underwater. To maximize the camera’s dust- and drip- resistance, keep the terminal cover, battery compartment cover, card slot cover, and all other covers firmly closed.
Handling Precautions Do not block the mirror operation with your finger, etc. Doing so may cause a malfunction. Use a blower to blow away dust on the lens, viewfinder, reflex mirror, and focusing screen. Do not use cleaners that contain organic solvents to clean the camera body or lens. For stubborn dirt, take the camera to the nearest Canon Service Center. Do not touch the camera’s electrical contacts with your fingers. This is to prevent the contacts from corroding.
Handling Precautions LCD Panel and LCD Monitor Although the LCD monitor is manufactured with very high precision technology with over 99.99% effective pixels, there may be a few dead pixels displaying only black or red, etc. among the remaining 0.01% or less pixels. Dead pixels are not a malfunction. They do not affect the images recorded. If the LCD monitor is left on for a prolonged period, screen burn-in may occur where you see remnants of what was displayed.
Nomenclature Drive mode selection/ AF operation/AF method selection button (p.142/86/268) Flash exposure compensation/ISO speed setting button (p.244/158) LCD panel illumination button (p.59) <6> Main Dial (p.56) White balance selection/ Metering mode selection button (p.174/212) AF area selection/ Multi-function button (p.92/244) Lens mount index (p.52) Flash sync contacts Hot shoe (p.244) Mode Dial lock-release button (p.56) Shutter button (p.55) Mode Dial (p.
Nomenclature LCD panel (p.29-30) Eyecup (p.236) Viewfinder eyepiece
AF start button (p.55, 86, 257, 291) AE lock button (p.217) AF point selection button (p.92-93) Info button (p.60, 75, 78, 258, 289, 320, 442) Power switch (p.47) Quick Control button (p.61) Menu button (p.64) Terminal cover <5> Quick Control Dial (p.57) Touch pad (p.58) <0> Setting button (p.64) External microphone IN terminal (p.301) Cable protector socket HDMI mini OUT terminal (p.
Nomenclature Dioptric adjustment knob (p.54) Focal plane mark Live View shooting/ Movie shooting switch (p.255/279) <0> Start/Stop button (p.256, 280) Creative Photo/ Comparative playback (Two-image display) button (p.164, 221, 226/332) <9> Multi-controller (p.58) Rating button (p.336, 337) Strap mount (p.35) Index/Magnify/ Reduce button (p.327/330) Card slot cover (p.43) Playback button (p.320) Erase button (p.358) Battery compartment cover release lever (p.
Nomenclature LCD Panel Shutter speed FE lock (FEL) Remaining number of exposures for time-lapse movie Busy (buSY) Multi function lock warning (L) No card warning (Card) Error code (Err) Cleaning image sensor (CLn) White balance (p.
Nomenclature HDR shooting (p.221) Multiple-exposure shooting (p.226) Bulb timer shooting (p.219) Interval timer shooting (p.239) GPS acquisition status Flash exposure compensation (p.244) Exposure level indicator Exposure compensation amount (p.214) AEB range (p.215) Flash exposure compensation amount (p.244) AF operation (p.86) X One-Shot AF 9 AI Focus AF Z AI Servo AF 4L Manual focus Drive mode (p.
Nomenclature Viewfinder Information Electronic level (p.75) Spot metering circle (p.213) Focusing screen Aspect ratio line (1:1) Single AF point Spot AF point (p.95) Grid (p.74) Crop area (1.6x) Area AF frame (p.91, 97) Crop area (1.3x) < > Battery level (p.48) Warning symbol (p.409) White balance (p.174) Flicker detection (p.191) Drive mode (p.142) AF operation (p.86) JPEG/RAW (p.149) Metering mode (p.212) * The display will show only the settings currently applied.
Nomenclature ISO speed (p.158) Focus indicator (p.80, 87) AE lock (p.217) AEB in-progress (p.215) Flash-ready (p.244) Improper FE lock warning FE lock (p.244) FEB in-progress (p.251) High-speed sync (p.251) Flash exposure compensation (p.244) Shutter speed (p.206) FE lock (FEL) Busy (buSY) Multi function lock warning (L) No card warning (Card) Error code (Err) Aperture (p.208) 32 AF status indicator (p.80) Maximum burst (p.153) Number of remaining multiple exposures (p.
Nomenclature Mode Dial You can set the shooting mode. Turn the Mode Dial while holding down the Mode Dial center (Mode Dial lock release button). F : Bulb (p.218) a : Manual exposure (p.210) f : Aperture-priority AE (p.208) s : Shutter-priority AE (p.206) d : Program AE (p.204) A : Scene Intelligent Auto (p.80) Custom shooting mode You can register the shooting mode (d/s/f/a/F), AF operation, menu settings, etc., to w, x, y Mode Dial positions (p.437).
Nomenclature Battery Charger LC-E6 Charger for Battery Pack LP-E6N/LP-E6 (p.40). Power plug Battery pack slot Charge lamp IMPORTANT SAFETY INSTRUCTIONS-SAVE THESE INSTRUCTIONS. DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS. For connection to a supply not in the U.S.A., use an attachment plug adapter of the proper configuration for the power outlet, if needed. Battery Charger LC-E6E Charger for Battery Pack LP-E6N/LP-E6 (p.40).
Nomenclature Attaching the Strap Pass the end of the strap through the camera’s strap mount eyelet from the bottom. Then pass it through the strap’s buckle as shown in the illustration. Pull the strap to take up any slack and make sure the strap will not loosen from the buckle. The eyepiece cover is also attached to the strap (p.236).
Nomenclature Using the Cable Protector When connecting the camera to a computer, printer, Wireless File Transmitter or GPS Receiver, use the provided interface cable or one from Canon (shown in the System Map on page 454). When connecting the interface cable, also use the provided cable protector. Using the cable protector prevents the cable from accidental disconnection and the terminal from getting damaged.
Nomenclature Using a Genuine Interface Cable (sold separately) If you use a genuine interface cable (sold separately, p.454), run the cable through the clamp before attaching the clamp to the cable protector. Clamp Connecting interface cable without using the cable protector may damage the digital terminal. Do not use a USB 2.0 cable equipped with a Micro-B plug. It may damage the camera’s digital terminal.
MEMO 38
1 Getting Started This chapter explains preparatory steps before you start shooting and basic camera operations.
Charging the Battery 1 Remove the protective cover. Detach the protective cover provided with the battery. the battery. 2 Attach As shown in the illustration, attach the battery securely to the charger. To detach the battery, follow the above procedure in reverse. LC-E6 the battery. 3 Recharge For LC-E6 As shown by the arrow, flip out the battery charger’s prongs and insert the prongs into a power outlet.
Charging the Battery Tips for Using the Battery and Charger Upon purchase, the battery is not fully charged. Charge the battery before use. Recharge the battery on the day before or on the day it is to be used. Even during storage, a charged battery will gradually drain and lose its capacity. After recharging the battery, detach it and disconnect the charger from the power outlet. You can attach the cover in a different orientation to indicate whether the battery has been recharged or not.
Installing and Removing the Battery Load a fully-charged Battery Pack LP-E6N (or LP-E6) into the camera. The camera’s viewfinder becomes bright when a battery is installed, and darkens when the battery is removed. Installing the Battery 1 Open the cover. Slide the lever as shown by the arrows and open the cover. the battery. 2 Insert Insert the end with the battery contacts. Insert the battery until it locks in place. the cover. 3 Close Press the cover until it snaps shut.
Installing and Removing the Card The camera can use a CF card and an SD card. Images can be recorded when at least one card is installed in the camera. If both types of card are inserted, you can select which card to record images to, or simultaneously record images on both cards (p.146-148). Cautions for Using an SD Card If you use an SD card, be sure the card’s write-protect switch is set upward to enable writing/erasing. Installing the Card 1 CF card SD card Write-protect switch Open the cover.
Installing and Removing the Card the cover. 3 Close Close the cover and slide it in the Possible Card selection icon shots direction shown by the arrows until it snaps shut. X When you set the power switch to <1> (p.47), the number of possible shots and the loaded card(s) will be displayed on the LCD panel. The images will be recorded to the card indicated by the arrow < > icon. CF card indicator SD card indicator The camera cannot use Type II CF cards, hard disk-type cards, or CFast cards.
Installing and Removing the Card Removing the Card 1 Open the cover. Set the power switch to <2>. Make sure the access lamp is off, then open the cover. If [Recording...] is displayed on the LCD monitor, close the cover. Access lamp the card. 2 Remove To remove the CF card, push the CF card eject button eject button. To remove the SD card, push it in gently and release it. Then pull it out. Pull the card straight out, then close the cover.
Installing and Removing the Card When the access lamp is lit or blinking, it indicates that images are being written to, read from, or erased from the card, or data is being transferred. Do not open the card slot cover during this time. Also, never do any of the following while the access lamp is lit or blinking. Otherwise, it can damage the image data, card, or camera. • Removing the card. • Removing the battery. • Shaking or banging the camera around.
Turning on the Power If you turn on the power switch and the date/time/zone setting screen appears, see page 49 to set the date/time/zone. <1> : The camera turns on. <2> : The camera is turned off and does not operate. Set to this position when not using the camera. Automatic Sensor Cleaning Whenever you set the power switch to <1> or <2>, sensor cleaning will be executed automatically. (A small sound may be heard.) During the sensor cleaning, the LCD monitor will display .
Turning on the Power z Battery Level Indicator When the power switch is set to <1>, the battery level will be indicated in one of six levels. A blinking battery icon indicates that the battery will be exhausted soon. Display Level (%) 100 - 70 69 - 50 49 - 20 19 - 10 Number of Possible Shots 9-1 0 (Approx.
3 Setting the Date, Time, and Zone When you turn on the power for the first time or if the date/time/zone are reset, the date/time/zone setting screen will appear. Follow the steps below, making sure to set the time zone first. Set the camera to the time zone in which you currently live so that, when you travel, you can simply change the setting to the correct time zone for your destination and the camera will automatically adjust the date/time.
3 Setting the Date, Time, and Zone the date and time. 4 SetTurn the <5> dial to select the number. Press <0> so is displayed. Turn the <5> dial to select the desired setting, then press <0> (Returns to ). saving time. 5 SetSettheit ifdaylight necessary. Turn the <5> dial to select [Y]. Press <0> so is displayed. Turn the <5> dial to select [Z], then press <0>. When the daylight saving time is set to [Z], the time set in step 4 will advance by 1 hr.
3 Selecting the Interface Language The date/time that were set will start from when you select [OK] in step 6. In step 3, the time displayed on the upper right of the screen is the time difference compared with Coordinated Universal Time (UTC). If you do not see your time zone, set the time zone while referring to the difference with UTC. 3 Selecting the Interface Language 1 Display the menu screen. Press the button to display the menu screen. the [52] tab, select 2 Under [LanguageK].
Attaching and Detaching a Lens The camera is compatible with all Canon EF lenses. The camera cannot be used with EF-S or EF-M lenses. Attaching a Lens 1 Remove the caps. Remove the rear lens cap and the body cap by turning them as shown by the arrows. the lens. 2 Attach Align the red dots on the lens and camera and turn the lens as shown by the arrow until it clicks in place. the lens’s focus mode switch 3 Set to . stands for autofocus. stands for manual focus. Autofocus will not operate.
Attaching and Detaching a Lens Detaching the Lens While pressing the lens release button, turn the lens as shown by the arrow. Turn the lens until it stops, then detach it. Attach the rear lens cap to the detached lens. Do not look at the sun directly through any lens. Doing so may cause loss of vision. When attaching or detaching a lens, set the camera’s power switch to <2>. If the front part (focusing ring) of the lens rotates during autofocusing, do not touch the rotating part.
Basic Operation Adjusting the Viewfinder Clarity Turn the dioptric adjustment knob. Turn the knob left or right so that the AF points in the viewfinder look sharp. If the knob is difficult to turn, remove the eyecup (p.236). If the camera’s dioptric adjustment still cannot provide a sharp viewfinder image, using Dioptric Adjustment Lens Eg (sold separately) is recommended. Holding the Camera To obtain sharp images, hold the camera still to minimize camera shake. Horizontal shooting Vertical shooting 1.
Basic Operation Shutter Button The shutter button has two steps. You can press the shutter button halfway. Then you can further press the shutter button completely. Pressing Halfway This activates autofocusing and the automatic exposure system that sets the shutter speed and aperture. The exposure setting (shutter speed and aperture) is displayed in the viewfinder and on the LCD panel for 4 sec. (metering timer/0). Pressing Completely This releases the shutter and takes the picture.
Basic Operation Mode Dial Turn the dial while holding down the lock release button at the center of the dial. Use it to set the shooting mode. 6 Main Dial (1) After pressing a button, turn the <6> dial. When you press a button such as , the respective function remains selected for 6 sec. (9). During this time, you can turn the <6> dial to change the setting. When the function selection ends or if you press the shutter button halfway, the camera will be ready to shoot.
Basic Operation 5 Quick Control Dial (1) After pressing a button, turn the <5> dial. When you press a button such as , the respective function remains selected for 6 sec. (9). During this time, you can turn the <5> dial to change the setting. When the function selection ends or if you press the shutter button halfway, the camera will be ready to shoot. Use this dial to select the white balance, drive mode, flash exposure compensation, AF point, etc. (2) Turn the <5> dial only.
Basic Operation 9 Multi-controller The <9> consists of an eight-direction key and a button at the center. Use your thumb to tilt the <9> in the desired direction. Use it to select the AF point, correct the white balance, move the AF point or magnifying frame during Live View shooting, scroll around magnified images during playback, operate the Quick Control screen, etc. You can also use it to select and set menu items.
Basic Operation R Multi Function Lock By setting [83: Multi function lock] (p.410) and moving the switch to the right, you can prevent the Main Dial, Quick Control Dial, and Multi-controller from moving and changing a setting inadvertently. switch set to the left: Lock released switch set to the right: Lock engaged If the switch is set to the right and you try to operate any of the locked camera controls, will appear in the viewfinder and on the LCD panel.
Basic Operation Displaying Quick Control Screen After you press the button a number of times (p.442), the Quick Control screen (p.62) or Custom Quick Control screen (p.427) will appear. You can then check the current shooting function settings. Pressing the button enables Quick Control of the shooting function settings (p.61). Then you can press the button to turn off the screen.
Q Quick Control for Shooting Functions You can directly select and set the shooting functions displayed on the LCD monitor. This is called Quick Control. The basic operating procedures are the same for the Quick Control screen (p.60) and the Custom Quick Control screen (p.427). 1 Press the button (7). X The Quick Control screen will appear. the desired functions. 2 SetUse <9> to select a function. X The setting of the selected function is displayed. Turn the <5> or <6> dial to change the setting.
Q Quick Control for Shooting Functions Settable Functions on Quick Control Screen Aperture (p.208) Shutter speed (p.206) AE lock* (p.217) Highlight tone priority* (p.187) Shooting mode* (p.33) Exposure compensation/ AEB setting (p.214/215) ISO speed (p.158) Flash exposure compensation (p.244) Picture Style (p.164) Custom Controls (p.413) AF operation (p.86) Image-recording quality (p.149) White balance (p.174) Metering mode (p.212) White balance correction / White balance bracketing (p.
Q Quick Control for Shooting Functions Quick Control Screen Ð <0> Select a function and press <0>. The function setting screen will appear. Turn the <6> or <5> dial to change some of the settings. There are also functions that are set by pressing the button. Press <0> to finalize the setting and return to the previous screen. When you select < > (p.413) and press the button, the previous screen will reappear.
3 Menu Operations You can set various settings with the menus such as the image-recording quality, date/time, etc. button <6> Main Dial LCD monitor <5> Quick Control Dial button <0> button A Mode Menu Screen * Certain menu tabs and menu items are not displayed in the mode.
3 Menu Operations Menu Setting Procedure 1 Display the menu screen. Press the button to display the menu screen. a tab. 2 Select Each time you press the button, the main tab will switch. Turn the <6> dial to select a secondary tab. For example, the [z5] tab refers to the screen displayed when the z (Shooting) tab’s fifth dot “ ” from the left is selected. the desired item. 3 Select Turn the <5> dial to select the item, then press <0>. the setting.
3 Menu Operations The explanation of menu functions hereinafter assumes that you have pressed the button to display the menu screen. You can also use <9> to operate and set menu functions. (Except for [31: Erase images] and [51: Format card].) To cancel the operation, press the button. For details about each menu item, see page 460. Dimmed Menu Items Example: When Multi Shot Noise Reduction is set Dimmed menu items cannot be set.
Before You Start 3 Formatting the Card If the card is new or was previously formatted by another camera or computer, format the card with this camera. Cautions for Formatting the Card When the card is formatted, all images and data on the card will be erased. Even protected images will be erased, so make sure there is nothing you need to keep. If necessary, transfer the images and data to a computer, etc., before formatting the card. 1 Select [Format card].
Before You Start Format the card in the following cases: The card is new. The card was formatted by a different camera or a computer. The card is full with images or data. A card-related error is displayed (p.487). Low-level Formatting Perform low-level formatting if the SD card’s reading or writing speed seems slow or if you want to totally erase all data on the card. Since low-level formatting will erase all recordable sectors on the SD card, the formatting will take longer than normal formatting.
Before You Start 3 Disabling the Beeper You can prevent the beeper from sounding when focus is achieved or during self-timer operation. 1 Select [Beep]. Under the [z1] tab, select [Beep], then press <0>. [Disable]. 2 Select Select [Disable], then press <0>. X The beeper will not sound. 3 Setting the Power-off Time/Auto Power Off To save battery power, the camera turns off automatically after a set time of idle operation elapses. The default setting is 1 min., but this setting can be changed.
Before You Start 3 Setting the Image Review Time You can set how long the image is displayed on the LCD monitor just after shooting. To keep the image displayed, set [Hold]. To not have the image displayed, set [Off]. 1 Select [Image review]. Under the [z1] tab, select [Image review], then press <0>. the desired time. 2 SetSelect the desired setting, then press <0>. If [Hold] is set, the image will be displayed until the auto power off time elapses.
Before You Start AF Settings Shooting Function Settings AF operation AF area selection mode AF point selection Registered AF point Metering mode ISO speed ISO speed range Auto ISO range One-Shot AF Single-point AF (Manual Selection) Center Canceled q (Evaluative metering) Auto Minimum limit: 100 Maximum limit: 6400 Minimum limit: 100 Maximum limit: 3200 Minimum shutter Auto speed Drive mode u (Single shooting) Exposure Canceled compensation/AEB Flash exposure Canceled compensation Multiple exposure Disa
Before You Start Image Recording Settings Camera Settings Image quality 73 Auto power off 1 min. Crop/aspect ratio Full-frame Beep Enable Picture Style Standard Auto Lighting Optimizer Enable Standard Release shutter without card Image review time 2 sec.
Before You Start Live View Shooting Settings Live View shooting AF method Continuous AF Grid display Enable u+Tracking Disable Off Exposure simulation Enable Silent LV shooting Mode 1 Metering timer 8 sec. Movie Shooting Settings Movie Servo AF Disable AF method u+Tracking Grid display Off Movie recording NTSC: L6X size PAL: L5X Sound recording Wind filter Attenuator Silent LV shooting Metering timer Time code Count up Start time setting Auto Disable Disable Mode 1 8 sec.
l Displaying the Grid You can display a grid in the viewfinder to help you check the camera tilt or compose the shot. 1 Select [Viewfinder display]. Under the [52] tab, select [Viewfinder display], then press <0>. 2 Select [Grid display]. [Show]. 3 Select X When you exit the menu, the grid will appear in the viewfinder. You can display a grid on the LCD monitor during Live View shooting and before you start shooting a movie (p.265, 315).
Q Displaying the Electronic Level You can display the electronic level on the LCD monitor and in the viewfinder to help you correct camera tilt. Displaying the Electronic Level on the LCD Monitor 1 Press the button. Each time you press the button, the screen display will change. Display the electronic level. If the electronic level does not appear, set [53: z button display options] so that the electronic level can be displayed (p.442). the camera’s tilt.
Q Displaying the Electronic Level 3 Displaying the Electronic Level in the Viewfinder An electronic level can be displayed on the upper part of the viewfinder. Since this can be displayed while you shoot, you can correct the camera tilt while shooting. 1 Select [Viewfinder display]. Under the [52] tab, select [Viewfinder display], then press <0>. 2 Select [Electronic level]. 3 Select [Show]. the shutter button halfway. 4 Press X The electronic level will be displayed in the viewfinder.
3 Setting the Viewfinder Information DisplayN The shooting function settings (Battery, White balance, Drive mode, AF operation, Metering mode, Image quality: JPEG/RAW, Flicker detection) can be displayed in the viewfinder. By default, only Flicker detection is checkmarked [X]. 1 Select [Viewfinder display]. Under the [52] tab, select [Viewfinder display], then press <0>. 2 Select [Show/hide in viewfinder]. [X] the information to 3 Checkmark be displayed.
Help When [z Help] is displayed at the bottom of the menu screen, the feature’s description (Help) can be displayed. The Help screen is displayed only while you hold down the button. If the Help fills more than one screen, a scroll bar will appear on the right edge. To scroll, hold down the button and turn the <5> dial.
2 Basic Shooting This chapter explains how to use the Mode Dial’s (Scene Intelligent Auto) mode for easy picture taking. In the mode, all you do is point and shoot and the camera sets everything automatically (p.456). Also, to prevent botched pictures due to mistaken operations, advanced shooting function settings cannot be changed. Scene Intelligent Auto Auto Lighting Optimizer In the mode, the Auto Lighting Optimizer (p.
A Fully Automatic Shooting (Scene Intelligent Auto) is a fully automatic mode. The camera analyzes the scene and sets the optimum settings automatically. It also adjusts focus automatically by detecting whether the subject is still or moving (p.83). 1 Area AF frame Set the Mode Dial to . Turn the Mode Dial while holding down the lock release button at the center. the Area AF frame over the 2 Aim subject. All the AF points will be used to focus, and the camera will focus on the closest object.
A Fully Automatic Shooting (Scene Intelligent Auto) the picture. 4 TakePress the shutter button completely to take the picture. X The captured image will be displayed for 2 sec. on the LCD monitor. The mode makes the colors look more impressive in nature, outdoor, and sunset scenes. If you did not obtain the desired color tones, change the mode to , , , or , set a Picture Style other than , then shoot again (p.164). FAQ The focus indicator blinks and focus is not achieved.
A Fully Automatic Shooting (Scene Intelligent Auto) Pressing the shutter button halfway does not focus on the subject. If the focus mode switch on the lens is set to (manual focus), set it to (autofocus). The shutter speed display is blinking. Since it is too dark, taking the picture may result in a blurred subject due to camera shake. Using a tripod or a Canon EX-series Speedlite (sold separately, p.244) is recommended.
A Full Auto Techniques (Scene Intelligent Auto) Recomposing the Shot Depending on the scene, position the subject toward the left or right to create a balanced background and good perspective. In the mode, pressing the shutter button halfway to focus on a still subject will lock the focus on that subject. Recompose the shot while keeping the shutter button pressed halfway, and then press the shutter button completely to take the picture. This is called “focus lock”.
A Full Auto Techniques (Scene Intelligent Auto) A Live View Shooting You can shoot while viewing the image on the LCD monitor. This is called “Live View shooting”. For details, see page 255. 1 Set the Live View shooting/Movie shooting switch to . the Live View image on 2 Display the LCD monitor. Press the <0> button. X The Live View image will appear on the LCD monitor. on the subject. 3 Focus Press the shutter button halfway to focus.
3 Setting the AF and Drive Modes The AF points in the viewfinder are arranged to make AF shooting suitable for a wide variety of subjects and scenes. You can also select the AF operation and drive mode that best match the shooting conditions and subject. A M icon at the upper right of a page title indicates a function that can be used only in the following modes: . In the mode, the AF operation and AF area selection mode are set automatically. stands for autofocus.
f: Selecting the AF OperationN You can select the AF operation characteristics to suit the shooting conditions or subject. In the mode, “AI Focus AF” is set automatically. 1 Set the lens’s focus mode switch to . the 2 Set mode. 3 Press the button. (9) the AF operation. 4 Select While looking at the LCD panel or in the viewfinder, turn the <6> dial.
f: Selecting the AF OperationN One-Shot AF for Still Subjects Suited for still subjects. When you press the shutter button halfway, the camera will focus only once. When focus is achieved, the AF point that achieved focus will be displayed, and the focus indicator in the viewfinder will also light up. With evaluative metering (p.212), the AF point Focus indicator exposure setting will be set at the same time as focus is achieved. While you hold down the shutter button halfway, the focus will be locked.
f: Selecting the AF OperationN AI Servo AF for Moving Subjects This AF operation is suited for moving subjects when the focusing distance keeps changing. While you hold down the shutter button halfway, the camera will keep focusing on the subject continuously. The exposure is set at the moment the picture is taken. When the AF area selection mode (p.90) is set to 61-point automatic selection AF, focus tracking will continue as long as the Area AF frame covers the subject.
f: Selecting the AF OperationN AF Operation Indicator While you press the shutter button halfway and the camera focuses with AF, the icon will appear under the focus indicator in the viewfinder. In One-Shot AF mode, the icon also appears if you press the shutter button halfway after focus is achieved. AF Points Lighting Up in Red By default, the AF points light up in red in low-light conditions. In the , , , , or mode, you can set whether to have the AF points light up in red (p.132).
S Selecting the AF Area and AF PointN The camera has 61 AF points for autofocusing. You can select the AF area selection mode and AF point(s) suiting the scene or subject. Depending on the lens attached to the camera, the number of usable AF points and AF point patterns will differ. For details, see “Lenses and Usable AF Points” on page 100. AF Area Selection Mode You can select one of six AF area selection modes. For the setting procedure, see page 92.
S Selecting the AF Area and AF PointN AF point expansion (Manual selection, surrounding points) The manually-selected AF point and the surrounding AF points are used to focus. Zone AF (Manual selection of zone) One of nine zones is used to focus. 61-point automatic selection AF The Area AF frame (entire AF area) is used to focus. This mode is set automatically in the mode.
S Selecting the AF Area and AF PointN Selecting the AF Area Selection Mode 1 Press the button. (9) the button. 2 Press Look through the viewfinder and press the button. Each time you press the button, the AF area selection mode changes. With [24: Select AF area selec. mode], you can limit the selectable AF area selection modes (p.125).
S Selecting the AF Area and AF PointN Selecting the AF Point Manually You can manually select the AF point or zone. 1 Press the button. (9) X The AF points will be displayed in the viewfinder. In AF point expansion modes, adjacent AF points will also be displayed. In the Zone AF mode, the selected zone will be displayed. an AF point. 2 Select The AF point selection will change in the direction you tilt <9>. If you press <9> straight down, the center AF point (or center zone) will be selected.
S Selecting the AF Area and AF PointN AF Point Display Indications Pressing the button lights up the AF points that are cross-type AF points for high-precision autofocusing. The blinking AF points are horizontal-line or vertical-line sensitive. For details, see pages 99-104. Registering the AF point You can register a frequently-used AF point to the camera. When you use the button set with the [83: Custom Controls] (p.
AF Area Selection ModesN Single-point Spot AF (Manual selection) For pinpoint focusing over a narrower area than with single-point AF (manual selection). Select one AF point < > to focus. Effective for pinpoint focusing or focusing overlapping subjects such as an animal in a cage. Since Single-point Spot AF (manual selection) covers a very small area, focusing may be difficult during hand-held shooting or for a moving subject.
AF Area Selection ModesN AF point expansion (Manual selection, surrounding points) The manually-selected AF point and surrounding AF points are used to focus. The AF point expansion is larger than with AF point expansion (manual selection ), so the focusing is executed over a wider area. Effective when it is difficult to track a moving subject with just one AF point. AI Servo AF and One-Shot AF work in the same way as with AF point expansion (manual selection ) mode (p.95).
AF Area Selection ModesN 61-point automatic selection AF The Area AF frame (entire AF area) is used to focus. This mode is set automatically in the mode. The AF point(s) achieving focus is displayed as . With One-Shot AF, pressing the shutter button halfway will display the AF point(s) that achieved focus. If multiple AF points are displayed, it means they all have achieved focus. This mode tends to focus on the nearest subject.
AF Area Selection ModesN When AI Servo AF mode is set with 61-point automatic selection AF, or Zone AF (manual selection of zone), the active AF point will keep switching to track the subject. However, under certain shooting conditions (such as when the subject is small), it may not be able to track the subject. Also, in low temperatures, the tracking response may become slower.
AF Sensor The camera’s AF sensor has 61 AF points. The illustration below shows the AF sensor pattern corresponding to each AF point. With f/2.8 or larger maximum aperture lenses, high-precision AF is possible at the viewfinder center. Depending on the lens attached to the camera, the number of usable AF points and AF pattern will differ. For details, see pages 100-108. Diagram Cross-type focusing: f/4 horizontal + f/5.6 vertical Cross-type focusing: f/5.6 vertical + f/5.6 horizontal f/5.
Lenses and Usable AF Points Although the camera has 61 AF points, the number of usable AF points and focusing patterns will differ depending on the lens. The lenses are thereby classified into nine groups from A to I. When using a lens in Groups F to H, fewer AF points will be usable. See which group each lens belongs to on pages 105-108. Check which group the lens in use belongs to. When you press the button, the AF points indicated by the mark will blink. (The / / AF points will stay lit.
Lenses and Usable AF Points Group B Autofocusing with 61 points is possible. All the AF area selection modes are selectable. : Dual cross-type AF point. Subject tracking is superior and the focusing precision is higher than with other AF points. : Cross-type AF point. Subject tracking is superior and highprecision focusing is achieved. : AF points sensitive to horizontal lines. Group C Autofocusing with 61 points is possible. All the AF area selection modes are selectable. : Cross-type AF point.
Lenses and Usable AF Points Group D Autofocusing with 61 points is possible. All the AF area selection modes are selectable. : Dual cross-type AF point. Subject tracking is superior and the focusing precision is higher than with other AF points. : Cross-type AF point. Subject tracking is superior and highprecision focusing is achieved. : AF points sensitive to horizontal lines. Group E Autofocusing with 61 points is possible. All the AF area selection modes are selectable. : Cross-type AF point.
Lenses and Usable AF Points Group F Autofocusing with only 47 points is possible. (Not possible with all 61 AF points.) All the AF area selection modes are selectable. During automatic AF point selection, the outer frame marking the AF area (Area AF frame) will be different from 61-point automatic selection AF. : Cross-type AF point. Subject tracking is superior and highprecision focusing is achieved. : AF points sensitive to horizontal lines. : Disabled AF points (not displayed).
Lenses and Usable AF Points Group H AF is possible with the center AF point and the adjacent AF points above, below, on the left, and on the right. Only the following AF area selection modes are selectable: Single-point AF (manual selection), Single-point Spot AF (manual selection), and AF point expansion (manual selection ). If an Extender is attached to the lens and the maximum aperture is f/8 (between f/5.6 and f/8), AF will be possible. : Cross-type AF point.
Lenses and Usable AF Points Lens Group Designations EF14mm f/2.8L USM EF14mm f/2.8L II USM EF15mm f/2.8 Fisheye EF20mm f/2.8 USM EF24mm f/1.4L USM EF24mm f/1.4L II USM EF24mm f/2.8 EF24mm f/2.8 IS USM EF28mm f/1.8 USM EF28mm f/2.8 EF28mm f/2.8 IS USM EF35mm f/1.4L USM EF35mm f/1.4L II USM EF35mm f/2 EF35mm f/2 IS USM EF40mm f/2.8 STM EF50mm f/1.0L USM EF50mm f/1.2L USM EF50mm f/1.4 USM EF50mm f/1.8 EF50mm f/1.8 II EF50mm f/1.8 STM EF50mm f/2.5 Compact Macro EF50mm f/2.
Lenses and Usable AF Points EF400mm f/2.8L USM + Extender EF2x EF400mm f/2.8L II USM EF400mm f/2.8L II USM + Extender EF1.4x EF400mm f/2.8L II USM + Extender EF2x EF400mm f/2.8L IS USM EF400mm f/2.8L IS USM + Extender EF1.4x EF400mm f/2.8L IS USM + Extender EF2x EF400mm f/2.8L IS II USM EF400mm f/2.8L IS II USM + Extender EF1.4x EF400mm f/2.8L IS II USM + Extender EF2x EF400mm f/4 DO IS USM EF400mm f/4 DO IS USM + Extender EF1.
Lenses and Usable AF Points EF28-80mm f/3.5-5.6 V USM EF28-90mm f/4-5.6 EF28-90mm f/4-5.6 USM EF28-90mm f/4-5.6 II EF28-90mm f/4-5.6 II USM EF28-90mm f/4-5.6 III EF28-105mm f/3.5-4.5 USM EF28-105mm f/3.5-4.5 II USM EF28-105mm f/4-5.6 EF28-105mm f/4-5.6 USM EF28-135mm f/3.5-5.6 IS USM EF28-200mm f/3.5-5.6 EF28-200mm f/3.5-5.6 USM EF28-300mm f/3.5-5.6L IS USM EF35-70mm f/3.5-4.5 EF35-70mm f/3.5-4.5A EF35-80mm f/4-5.6 EF35-80mm f/4-5.6 PZ EF35-80mm f/4-5.6 USM EF35-80mm f/4-5.6 II EF35-80mm f/4-5.
Lenses and Usable AF Points EF200-400mm f/4L IS USM Extender E 1.4x + Extender EF1.4x EF200-400mm f/4L IS USM Extender 1.4x: With built-in Ext. 1.4x H (f/8) + Extender EF1.4x EF200-400mm f/4L IS USM Extender H (f/8) 1.4x + Extender EF2x TS-E17mm f/4L C TS-E24mm f/3.5L C TS-E24mm f/3.5L II C TS-E45mm f/2.8 A TS-E90mm f/2.8 A When using a lens and an extender in the combination marked with *, precise focus may not be achieved with AF. Refer to the instruction manual of the lens or extender used.
3 Selecting AI Servo AF CharacteristicsN You can easily fine-tune AI Servo AF to suit a particular subject or shooting scene just by selecting an option from case 1 to case 6. This feature is called the “AF Configuration Tool.” 1 Select the [21] tab. a case. 2 Select Turn the <5> dial to select a case icon, then press <0>. X The selected case will be set. The selected case is indicated in blue.
3 Selecting AI Servo AF CharacteristicsN Case 1: Versatile multi purpose setting Default settings • Tracking sensitivity: 0 • Accel./decel. tracking: 0 • AF pt auto switching: 0 Standard setting suited for any moving subject. Works with many subjects and scenes.
3 Selecting AI Servo AF CharacteristicsN Case 3: Instantly focus on subjects suddenly entering AF points Default settings • Tracking sensitivity: Responsive: +1 • Accel./decel. tracking: +1 • AF pt auto switching: 0 Once an AF point starts tracking the subject, this setting enables the camera to consecutively focus on subjects at different distances. If a new subject appears in front of the target subject, the camera will start focusing on the new subject.
3 Selecting AI Servo AF CharacteristicsN Case 5: For erratic subjects moving quickly in any direction Default settings • Tracking sensitivity: 0 • Accel./decel. tracking: 0 • AF pt auto switching: +1 Even if the target subject moves dramatically up, down, left, or right, the AF point will switch automatically to focus-track the subject. Effective for shooting subjects that move dramatically up, down, left, or right.
3 Selecting AI Servo AF CharacteristicsN Case 6: For subjects that change speed and move erratically Default settings • Tracking sensitivity: 0 • Accel./decel. tracking: +1 • AF pt auto switching: +1 Geared for tracking moving subjects whose speed can change dramatically and suddenly. Also, if the target subject moves dramatically up, down, left or right and it is difficult to focus, the AF point switches automatically to track the subject.
3 Selecting AI Servo AF CharacteristicsN Parameters Tracking sensitivity Sets the subject-tracking sensitivity during AI Servo AF when an obstacle enters the AF points or when the AF points stray from the subject. 0 Default setting. Suitable for moving subjects in general. Locked on: -2 / Locked on: -1 The camera will try to continue focusing on the subject even if an obstacle enters the AF points or if the subject strays from the AF points.
3 Selecting AI Servo AF CharacteristicsN Acceleration/deceleration tracking This sets the tracking sensitivity for moving subjects whose speed can suddenly change dramatically by starting or stopping suddenly, etc. 0 Suited for subjects that move at a steady speed (minimal change in moving speed). +2 / +1 Effective for subjects having sudden movements, sudden acceleration/deceleration, or sudden stops.
3 Selecting AI Servo AF CharacteristicsN AF point auto switching This sets the switching sensitivity of the AF points as they track the subject moving dramatically up, down, left, or right. This setting takes effect when the AF area selection mode is set to AF point expansion (manual selection ), AF point expansion (manual selection, surrounding points), Zone AF (manual selection of zone), or 61-point automatic selection AF. 0 Standard setting for gradual AF point switching.
3 Selecting AI Servo AF CharacteristicsN Changing Cases’ Parameter Settings You can manually adjust each case’s three parameters: 1. Tracking sensitivity, 2. Acceleration/deceleration tracking, and 3. AF point auto switching. 1 Select a case. Turn the <5> dial to select the icon of the case you want to adjust. the button. 2 Press The selected parameter will have a purple frame. the parameter to adjust. 3 Select Select the parameter to adjust, then press <0>.
3 Customizing AF FunctionsN With the [22] to [25] menu tabs, you can set the AF functions to suit your shooting style or subject. 22: AI Servo AI Servo 1st image priority You can set the AF operation characteristics and shutter-release timing for the first shot with AI Servo AF. : Equal priority Equal priority is given to focusing and shutter release. : Release priority Pressing the shutter button takes the picture immediately even if focus has not been achieved.
3 Customizing AF FunctionsN AI Servo 2nd image priority You can set the AF operation characteristics and shutter-release timing during continuous shooting after the first shot with AI Servo AF. : Equal priority Equal priority is given to focusing and continuous shooting speed. In low light or with low-contrast subjects, shooting speed may slow down. : Shooting speed priority Priority is given to the continuous shooting speed instead of achieving focus.
3 Customizing AF FunctionsN 23: One Shot Lens electronic MF With the following USM and STM lenses equipped with an electronic manual focusing function, you can set whether to use electronic manual focusing. EF50mm f/1.0L USM EF85mm f/1.2L USM EF85mm f/1.2L II USM EF200mm f/1.8L USM EF300mm f/2.8L USM EF400mm f/2.8L USM EF400mm f/2.8L II USM EF500mm f/4.5L USM EF600mm f/4L USM EF1200mm f/5.6L USM EF28-80mm f/2.8-4L USM EF70-300mm f/4-5.6 IS II USM EF40mm f/2.8 STM EF50mm f/1.8 STM EF24-105mm f/3.5-5.
3 Customizing AF FunctionsN AF-assist beam firing Enables or disables the AF-assist beam from the EOS-dedicated external Speedlite. ON: Enable The external Speedlite emits the AFassist beam when necessary. OFF: Disable The external Speedlite will not emit the AF-assist beam. Prevents the AFassist beam from disturbing others. IR: IR AF assist beam only When an external Speedlite is attached, only the infrared AF-assist beam will be emitted.
3 Customizing AF FunctionsN One-Shot AF release priority You can set the AF operation characteristics and shutter-release timing for One-Shot AF. : Focus priority The picture will not be taken until focus is achieved. Effective when you want to achieve focus before capturing the shot. : Release priority Priority is given to the timing of shutter release instead of achieving focus. This gives priority to capturing the image rather than achieving correct focus.
3 Customizing AF FunctionsN 24 Lens drive when AF impossible If focus cannot be achieved with autofocus, you can have the camera keep searching for the correct focus or have it stop searching. ON: Continue focus search If focus cannot be achieved with autofocus, the lens is driven to search for the correct focus. OFF: Stop focus search If autofocus starts and the focus is far off or if focus cannot be achieved, the lens drive will not be performed.
3 Customizing AF FunctionsN Selectable AF point You can change the number of manually selectable AF points. If 61point automatic selection AF is set, the Area AF frame (entire AF area) will be used for AF regardless of the setting below. : 61 points All AF points will be manually selectable. : Only cross-type AF points Only cross-type AF points will be manually selectable. The number of selectable cross-type AF points will differ depending on the lens.
3 Customizing AF FunctionsN Select AF area selection mode You can limit the selectable AF area selection modes to suit your shooting preferences. Select the desired selection mode and press <0> to append a checkmark . Then select [OK] to register the setting. : Manual select.:Spot AF For pinpoint focusing with a narrower area than single-point AF (manual selection). : Manual selection:1 pt AF One of the AF points set by [Selectable AF point] setting can be selected.
3 Customizing AF FunctionsN AF area selection method You can set the method for changing the AF area selection mode. 9 M-Fn button After you press the button, pressing the button, the AF area selection mode changes. 9 Main Dial After you press the button, turning the <6> dial changes the AF area selection mode. When [S 9 Main Dial] is set, use the <9> to move the AF point horizontally.
3 Customizing AF FunctionsN : Separate AF pts: Area+pt The AF area selection mode and AF point (or zone) can be set separately for each camera orientation (1. Horizontal, 2. Vertical with the camera grip at the top, 3. Vertical with the camera grip at the bottom). When you manually select the AF area selection mode and AF point (or zone) for each of the three camera orientations, they will be set for the respective orientation.
3 Customizing AF FunctionsN Initial AF Point, AI Servo AF You can set the AI Servo AF’s starting AF point for when the AF area selection mode is set to Auto selection: 61 pt AF. : Initial AF pt selected AI Servo AF will start with the manually-selected AF point when the AF operation is set to AI Servo AF and the AF area selection mode is set to Auto selection: 61 pt AF. : Manual AF pt If you switch from Manual select.
3 Customizing AF FunctionsN Auto AF point selection: EOS iTR AF EOS iTR* AF executes autofocus by recognizing faces and subject colors. EOS iTR AF works when the AF area selection mode is set to 61-point automatic selection AF or Zone AF (manual selection of zone). * intelligent Tracking and Recognition: The function that the metering sensor identifies the subject to make the AF points tracking it.
3 Customizing AF FunctionsN 25 Manual AF point selection pattern During manual AF point selection, the selection can either stop at the outer edge or it can cycle around to the opposite side. This function works in AF area selection modes other than Zone AF (manual selection of zone), and 61-point automatic selection AF (works with AI Servo AF). : Stops at AF area edges Convenient if you often use an AF point at the periphery.
3 Customizing AF FunctionsN AF point display during focus You can set whether or not to display the AF point(s) in the following cases: 1. When selecting the AF point(s), 2. When the camera is ready to shoot (before AF operation), 3. During AF operation, and 4. When focus is achieved. : Selected (constant) The selected AF point(s) is always displayed. : All (constant) All AF points are always displayed. : Selected (pre-AF, focused) The selected AF point(s) is displayed for 1, 2, and 4.
3 Customizing AF FunctionsN VF display illumination You can set whether the AF points in the viewfinder are to light up in red when focus is achieved. AUTO: Auto The AF points automatically light up in red under low light. ON: Enable The AF points light up in red regardless of the ambient light level. OFF: Disable The AF points do not light up in red. With [Auto] or [Enable] set, you can set whether the AF point lights up in red (blink) when you press the button during AI Servo AF.
3 Customizing AF FunctionsN AF Microadjustment You can make fine adjustments for the AF’s point of focus. For details, see “Fine Adjustment of AF’s Point of Focus” on the next page.
3 Fine Adjustment of AF’s Point of FocusN Fine adjustment of the AF’s point of focus is possible for viewfinder shooting. This is called “AF Microadjustment”. Before making the adjustment, read “General Cautions for AF Microadjustment” on page 139. Cautions for AF Microadjustment Normally, this adjustment is not required. Perform this adjustment only if necessary. Note that performing this adjustment may prevent accurate focusing from being achieved.
3 Fine Adjustment of AF’s Point of FocusN the adjustment. 4 Make Set the adjustment amount. The adjustable range is ±20 steps. Setting it toward “-: ” will shift the point of focus in front of the standard point of focus. Setting it toward “+: ” will shift the point of focus to the rear of the standard point of focus. After making the adjustment, press <0>. Select [All by same amount], then press <0>. the result of the 5 Check adjustment. Take a picture and play back the image (p.
3 Fine Adjustment of AF’s Point of FocusN Adjust by Lens You can make the adjustment for each lens and register the adjustment in the camera. You can register the adjustment for up to 40 lenses. When you autofocus with a lens whose adjustment is registered, the point of focus will always be shifted by the adjustment amount. Set the adjustment manually by adjusting, shooting, and checking the result. Repeat this until the desired adjustment is made.
3 Fine Adjustment of AF’s Point of FocusN Entering the Serial Number Select the digit to be entered, then press <0> so is displayed. Enter the number, then press <0>. After entering all the digits, select [OK]. Lens Serial Number In step 3, if “ * ” appears in front of the 10-digit lens serial number, you can register only one unit of the same lens model. Even if you enter the serial number, “ * ” will remain displayed.
3 Fine Adjustment of AF’s Point of FocusN Single focal length lens Zoom lens the adjustment. 4 Make For a zoom lens, select the wide-angle (W) or telephoto (T) end. Pressing <0> will turn off the purple frame and make the adjustment possible. Set the adjustment amount, then press <0>. The adjustable range is ±20 steps. Setting it toward “-: ” will shift the point of focus in front of the standard point of focus.
3 Fine Adjustment of AF’s Point of FocusN When shooting with the intermediate range (focal length) of a zoom lens, the AF’s point of focus is corrected automatically relative to the adjustments made for the wide-angle and telephoto ends. Even if only the wide-angle or telephoto end is adjusted, a correction will be made automatically for the intermediate range.
When Autofocus Fails Autofocus can fail to achieve focus (viewfinder’s focus indicator blinks) with certain subjects such as the following: Subjects Difficult to Focus Subjects with very low contrast (Example: Blue skies, solid-color flat surfaces, etc.) Subjects in very low light Strongly backlit or reflective subjects (Example: Cars with highly reflective bodies, etc.) Near and distant subjects framed close to an AF point (Example: Animals in cages, etc.
When Autofocus Fails MF: Manual Focus 1 Set the lens’s focus mode switch to . X <4 L> will be displayed on the LCD panel. Focusing ring on the subject. 2 Focus Focus by turning the lens’s focusing ring until the subject looks sharp in the viewfinder. If you press the shutter button halfway while focusing manually, the focus indicator will light up when focus is achieved. With 61-point automatic selection AF, when the center AF point achieves focus, the focus indicator will light up.
o Selecting the Drive Mode Single and continuous drive modes are provided. You can select the drive mode suiting the scene or subject. 1 Press the button. (9) the drive mode. 2 Select While looking at the LCD panel or in the viewfinder, turn the <5> dial. u : Single shooting When you press the shutter button completely, only one shot will be taken. o: High-speed continuous shooting While you hold down the shutter button completely, the camera will shoot continuously at a maximum of approx. 5.
o Selecting the Drive Mode Q : 10-sec. self-timer/remote control k: 2-sec. self-timer/remote control For self-timer shooting, see page 144. For remote control shooting, see page 237. o: The maximum continuous shooting speed of approx. 5.0 shots/sec. is attained under the following conditions*: 1/500 sec. or faster shutter speed, maximum aperture (varies depending on the lens), Anti-flicker shooting set to Disable, with a fully-charged Battery Pack LP-E6N, and at room temperature (23°C/73°F).
j Using the Self-timer Use the self-timer when you want to be in the picture. 1 Press the button. (9) the self-timer. 2 Select While looking at the LCD panel or in the viewfinder, turn the <5> dial. Q : 10-sec. self-timer k : 2-sec. self-timer picture. 3 TakeLookthethrough the viewfinder, focus on the subject, then press the shutter button completely. X You can check the self-timer operation with the self-timer lamp, beeper, and countdown display (in seconds) on the LCD panel. X 2 sec.
4 Image Settings This chapter explains image-related function settings: Image-recording quality, Crop/aspect, ISO speed, Picture Style, white balance, Auto Lighting Optimizer, noise reduction, highlight tone priority, lens aberration correction, anti-flicker shooting, and other functions. A M icon at the upper right of a page title indicates a function that can be used only in the following modes: .
3 Selecting the Card for Recording and Playback If either a CF card or SD card is already inserted in the camera, you can start recording captured images. When only one card is inserted, you do not have to follow the procedures described on pages 146-148. If you insert both a CF card and SD card, you can select the recording method and select which card to use for recording and playing back images. [f] indicates the CF card, and [g] the SD card.
3 Selecting the Card for Recording and Playback Standard Images will be recorded to the card selected with [Record/play]. Auto switch card Same as with the [Standard] setting, but if the card becomes full, the camera will automatically switch to the other card to record images. When the card is automatically switched, a new folder will be created. Rec. separately You can set the image-recording quality for each card (p.149).
3 Selecting the Card for Recording and Playback Selecting the CF or SD Card for Recording and Playback If [Record func.] is set to [Standard] or [Auto switch card], select the card for recording and playing back images. If [Record func.] is set to [Rec. separately] or [Rec. to multiple], select the card for playing back images. Standard / Auto switch card Select [Record/play]. Select [Record/play], then press <0>. f : Record images to and play images back from the CF card.
3 Setting the Image-Recording Quality You can select the pixel count and the image quality. There are ten JPEG image-recording quality settings: 73, 83, 7K, 8K, 75, 85, 7a, 8a, b, c. There are three RAW image quality settings: 1, 41, 61 (p.152). 1 Standard / Auto switch card / Rec. to multiple Select [Image quality]. Under the [z1] tab, select [Image quality], then press <0>. the image-recording quality. 2 Select To select a RAW quality, turn the <6> dial. To select a JPEG quality, turn the <5> dial.
3 Setting the Image-Recording Quality Image-recording Quality Setting Examples 73 only 1 only 1+73 61+7K The image size [****x****] and number of possible shots [****] displayed on the Image-recording quality setting screen always apply to the [Full-frame] setting regardless of the [z4: Crop/aspect ratio] setting (p.154). The number of possible shots displayed on the LCD panel and Live View shooting screen during shooting is based on the [z4: Crop/aspect ratio] setting.
3 Setting the Image-Recording Quality Guide to Image-Recording Quality Settings (Approx.) Image Quality 73 83 7K 8K JPEG 75 Pixels Recorded Print Size 50M A1 39M 14.1 510 31 (510) 7.0 1030 1030 (1030) 10.9 660 45 (660) 5.5 1310 1310 (1310) 1010 1010 (1010) 2030 2030 (2030) 4.5 1590 1590 (1590) 2.3 3120 3120 (3120) 9x13 cm 1.2 5600 5600 (5600) - 0.3 20380 20380 (20380) 12M A3 b*1 2.5M c*2 0.3M 1 8a Maximum Burst 7.1 A2 7a Possible Shots 3.
3 Setting the Image-Recording Quality Even if you use a UDMA card, the maximum burst indicator remains the same. However, the maximum burst in parentheses on the preceding page will be applied during continuous shooting. If you select both RAW and JPEG, the same image will be recorded simultaneously to the card in both RAW and JPEG at the imagerecording qualities that were set. The two images will be recorded with the same file numbers (file extension: .JPG for JPEG and .CR2 for RAW).
3 Setting the Image-Recording Quality One-touch Image Quality Setting With Custom Controls, you can assign the image-recording quality to the button or depth-of-field preview button so you can switch to it momentarily. If you assign [One-touch image quality setting] or [One-touch image quality (hold)] to the button or depth-offield preview button, you can quickly switch to the desired imagerecording quality and shoot. For details, see Custom Controls (p.413). Under [51: Record func+card/folder sel.
Setting Crop/Aspect RatioN Normally, images are recorded at the sensor size of approx. 36.0 mm x 24.0 mm (full-frame shooting). You can record only the center of the image magnified approx. 1.3x (equivalent to APS-H size) or approx. 1.6x (equivalent to APS-C size) as if you were using a telephoto lens (crop shooting) or set the desired aspect ratio before you shoot. 1 Select [Crop/aspect ratio]. Under the [z4] tab, select [Crop/ aspect ratio], then press <0>. the desired setting.
Setting Crop/Aspect RatioN Example settings With e•b the picture. 4 Take Viewfinder shooting The shooting area in the viewfinder will be masked or have frame lines. The area surrounded by the semitransparent masking or frame lines will be recorded as an image. With f•c With d With g•b Live View shooting When [1.3x (crop)] or [1.6x (crop)] is set, the displayed image will be magnified by approx. 1.3x or 1.6x respectively.
Setting Crop/Aspect RatioN The [z4: Crop/aspect ratio] setting does not work with movie shooting and multiple exposures. The 4:3 and 16:9 aspect ratios cannot be used with viewfinder shooting. [83: Add cropping information] can be set only when [Full-frame] has been set for Crop/aspect ratio. An external Speedlite’s flash zoom (automatic flash coverage) will not work in tandem with the [z4: Crop/aspect ratio] setting. The image coverage with viewfinder shooting will be as follows: • With [1.
Setting Crop/Aspect RatioN Pixels Recorded in Crop/Aspect Ratio Settings (Approx.) Image Quality Full-frame (3:2) 1.3x (crop) 1.6x (crop) 3 8688x5792 (50.3 megapixels) 6768x4512 (30.5 megapixels) 5424x3616 (19.6 megapixels) K 7680x5120 (39.3 megapixels) 6016x4000* (24.1 megapixels) 4800x3200 (15.4 megapixels) 5 5760x3840 (22.1 megapixels) 4512x3008 (13.6 megapixels) 3616x2408* (8.7 megapixels) a 4320x2880 (12.4 megapixels) 3376x2256* (7.6 megapixels) 2704x1808* (4.
i: Setting the ISO SpeedN Set the ISO speed (image sensor’s sensitivity to light) to suit the ambient light level. With the mode selected, the ISO speed will be set automatically (p.160). Regarding the ISO speed during movie shooting, see pages 283 and 287. 1 Press the button. (9) the ISO speed. 2 SetWhile looking at the LCD panel or in the viewfinder, turn the <6> dial. ISO speed can be set within ISO 100 - ISO 6400 in 1/3-stop increments. “A” indicates Auto ISO.
i: Setting the ISO SpeedN As H (equivalent to ISO 12800) is an expanded ISO speed setting, noise (dots of light, banding, etc.) and irregular colors will be more noticeable, and the resolution lower than usual. As L (equivalent to ISO 50) is an expanded ISO speed setting, the dynamic range will be somewhat narrower than usual. If [z3: Highlight tone priority] is set to [Enable] (p.187), L (equivalent to ISO 50), ISO 100/125/160, and H (equivalent to ISO 12800) cannot be selected.
i: Setting the ISO SpeedN Auto ISO If the ISO speed is set to “A” (Auto), the actual ISO speed to be set will be displayed when you press the shutter button halfway. As indicated below, the ISO speed will be set automatically to suit the shooting mode.
i: Setting the ISO SpeedN 3 Setting the Manually-Settable ISO Speed Range You can set the manually-settable ISO speed range (minimum and maximum limits). You can set the minimum limit within L (equivalent to ISO 50) to ISO 6400, and the maximum limit within ISO 100 to H (equivalent to ISO 12800). 1 Select [ISO speed settings]. Under the [z2] tab, select [ISO speed settings], then press <0>. 2 Select [ISO speed range]. the minimum limit. 3 SetSelect the minimum limit box, then press <0>.
i: Setting the ISO SpeedN 3 Setting the ISO Speed Range for Auto ISO You can set the automatic ISO speed range for Auto ISO within ISO 100 - ISO 6400. You can set the minimum limit within ISO 100 - ISO 3200, and the maximum limit within ISO 200 - ISO 6400 in 1-stop increments. 1 Select [Auto ISO range]. the minimum limit. 2 SetSelect the minimum limit box, then press <0>. Select the ISO speed, then press <0>. the maximum limit. 3 SetSelect the maximum limit box, then press <0>.
i: Setting the ISO SpeedN 3 Setting the Minimum Shutter Speed for Auto ISO You can set the minimum shutter speed so that the shutter speed set automatically will not be too slow when Auto ISO is set. This is convenient in the and modes when you use a wideangle lens to shoot a moving subject or when you use a telephoto lens. It helps to reduce camera shake and blurred subjects. 1 Automatically set Manually set Select [Min. shutter spd.]. the desired minimum shutter 2 Set speed.
A Selecting a Picture StyleN By selecting a Picture Style, you can obtain image characteristics matching your photographic expression or the subject. The Picture Style is set automatically to [D] (Auto) in the mode. 1 Press the button. [A]. 2 Select X The Picture Style selection screen will appear. a Picture Style. 3 Select X The Picture Style will be set and the camera will be ready to shoot. You can also select the Picture Style with [z3: Picture Style].
A Selecting a Picture StyleN Picture Style Characteristics D Auto The color tone will be adjusted automatically to suit the scene. The colors will look vivid, especially for blue skies, greenery and sunsets, and in nature, outdoor and sunset scenes. If the desired color tone is not obtained with [Auto], use another Picture Style. P Standard The image looks vivid, sharp, and crisp. This is a general-purpose Picture Style suitable for most scenes. Q Portrait For nice skin tones. The image looks softer.
A Selecting a Picture StyleN U Faithful Suited for processing the image with a computer. The color of a subject that is captured in sunlight at a color temperature of 5200K will be adjusted to match the subject’s colorimetrical color. For subdued images with modest brightness and color saturation. V Monochrome Creates black-and-white images. Black-and-white images shot in JPEG cannot be turned into color. If you want to later shoot pictures in color, make sure the [Monochrome] setting is canceled.
A Selecting a Picture StyleN Symbols The Picture Style selection screen has icons for [Strength], [Fineness], or [Threshold] of [Sharpness], [Contrast], and other parameters. The numerals indicate the set values for these parameters as set by the respective Picture Style.
A Customizing a Picture StyleN You can customize the Picture Styles. You can change or adjust the parameter settings of Picture Styles such as [Strength], [Fineness], or [Threshold] of [Sharpness], and [Contrast], and other parameters from the default settings. To see the resulting effects, take test shots. To customize [Monochrome], see page 171. 1 Press the button. [A]. 2 Select X The Picture Style selection screen will appear. a Picture Style. 3 Select Select a Picture Style, then press button.
A Customizing a Picture StyleN the parameter. 5 SetAdjust the parameter as desired, then press <0>. Press the button to save the adjusted parameters. The Picture Style selection screen will reappear. X Any parameter settings different from the default will be displayed in blue. By selecting [Default set.] in step 4, you can revert the parameter settings of the respective Picture Style to its default. To shoot with the Picture Style you adjusted, first select the adjusted Picture Style, then shoot.
A Customizing a Picture StyleN Parameter Settings and Effects Sharpness g A Strength 0: Less sharp outline 7: Sharp outline B Fineness*1 1: Fine 5: Coarse C Threshold*2 1: Low 5: High h Contrast -4: Low contrast +4: High contrast i Saturation -4: Low saturation +4: High saturation j Color tone -4: Reddish skin tone +4: Yellowish skin tone *1: Indicates the fineness of the outlines to be emphasized. The smaller the number, the finer the outlines can be emphasized.
A Customizing a Picture StyleN V Monochrome Adjustment Besides [Strength], [Fineness], or [Threshold] of [Sharpness] and [Contrast], you can also set [Filter effect] and [Toning effect]. kFilter effect With a filter effect applied to a monochrome image, you can make white clouds or green trees stand out more. Filter Sample Effects N: None Normal black-and-white image with no filter effects. Ye: Yellow The blue sky will look more natural, and the white clouds will look crisper.
A Registering a Picture StyleN You can select a base Picture Style such as [Portrait] or [Landscape], adjust its parameters as desired and register it under [User Def. 1], [User Def. 2], or [User Def. 3]. You can create multiple Picture Styles with different settings for parameters such as sharpness and contrast. You can also adjust the parameters of a Picture Style that is registered to the camera with EOS Utility (EOS software, p.520). 1 Press the button. [A].
A Registering a Picture StyleN a parameter. 6 Select Select the parameter (such as [Sharpness] - [Strength]) to be set, then press <0>. the parameter. 7 SetAdjust the parameter as desired, then press <0>. For details, see “Customizing a Picture Style” (p.168). Press the button to register the modified Picture Style. The Picture Style selection screen will then reappear. X The base Picture Style will be indicated on the right of [User Def. *].
B: Setting the White BalanceN White balance (WB) is for making the white areas look white. Normally, the Auto [Q] (Ambience priority) or [Qw] (White priority) setting will obtain the correct white balance. If natural-looking colors cannot be obtained with Auto, you can select the white balance to match the light source or set it manually by shooting a white object. is automatically set in the [Q] (Ambience priority) mode. 1 Press the button. (9) a white balance setting.
B: Setting the White BalanceN White Balance To the human eye, a white object looks white regardless of the type of lighting. With a digital camera, the white for color correction basis is decided depending on the color temperature of the illumination, and then the color is adjusted with software to make the white areas look white. With this function, pictures with natural color shades can be taken.
B: Setting the White BalanceN Cautions for Setting [Qw] (White priority) The reddish color cast of subjects may fade. When multiple light sources are included on the screen, the red color cast of the picture may not be lessened. When using flash, the color tone will be the same as [Q] (Ambience priority). O Custom White Balance Custom white balance enables you to manually set the white balance for a specific light source for better accuracy. Perform this procedure under the actual light source to be used.
B: Setting the White BalanceN the white balance data. 3 Import Turn the <5> dial to select the image captured in step 1, then press <0>. X On the dialog screen that appears, select [OK] and the data will be imported. Press the button to exit the menu. 4 Press the button. (9) the custom white balance. 5 Select Look at the LCD panel and turn the <5> dial to select . If the exposure obtained in step 1 differs greatly from the standard exposure, a correct white balance may not be obtained.
B: Setting the White BalanceN P Setting the Color Temperature You can set the white balance’s color temperature numerically. This is for advanced users. 1 Select [White balance]. Under the [z2] tab, select [White balance], then press <0>. the color temperature. 2 SetSelect [P]. Turn the <6> dial to set the color temperature, then press <0>. The color temperature can be set from approx. 2500 K to 10000 K in 100 K increments.
u White Balance CorrectionN You can correct the white balance that is set. This adjustment will have the same effect as using a commercially-available color temperature conversion filter or color compensating filter. Each color can be corrected to one of nine levels. This function is for advanced users who are familiar with using color temperature conversion or color compensating filters. White Balance Correction 1 Select [WB Shift/Bkt.]. Under the [z2] tab, select [WB Shift/Bkt.], then press <0>.
u White Balance CorrectionN White Balance Auto Bracketing With just one shot, three images with different color tones can be recorded simultaneously. Based on the color temperature of the current white balance setting, the image will be bracketed with a blue/amber bias or magenta/green bias. This is called white balance bracketing (WB-BKT). White balance bracketing is possible up to ±3 levels in single-level increments. Set the white balance bracketing amount.
u White Balance CorrectionN During WB bracketing, the maximum burst for continuous shooting will be lower. Since three images are recorded for one shot, it takes longer to record the image to the card. You can also set white balance correction and AEB together with white balance bracketing. If you set AEB in combination with white balance bracketing, a total of nine images will be recorded for a single shot. When white balance bracketing is set, the white balance icon will blink.
3 Auto Correction of Brightness and ContrastN If the image comes out dark or the contrast is low, the brightness and contrast can be corrected automatically. This function is called Auto Lighting Optimizer. The default setting is [Standard]. With JPEG images, the correction is applied when the image is captured. [Standard] is automatically set in the mode. 1 Select [Auto Lighting Optimizer]. Under the [z2] tab, select [Auto Lighting Optimizer], then press <0>. the setting.
3 Setting Noise ReductionN High ISO Speed Noise Reduction This function reduces the noise generated in the image. Although noise reduction is applied at all ISO speeds, it is particularly effective at high ISO speeds. At low ISO speeds, the noise in the darker parts of the image (shadow areas) is further reduced. 1 Select [High ISO speed NR]. Under the [z3] tab, select [High ISO speed NR], then press <0>. the level. 2 SetSelect the desired noise reduction level, then press <0>.
3 Setting Noise ReductionN Cautions for Setting Multi Shot Noise Reduction If there is significant misalignment in the image due to camera shake, the noise reduction effect may be minimal. If you are handholding the camera, keep it steady to prevent camera shake. Using a tripod is recommended. If you shoot a moving subject, the moving subject may leave afterimages. The image alignment may not function properly with repetitive patterns (lattice, stripes, etc.) or flat, single-tone images.
3 Setting Noise ReductionN Long Exposure Noise Reduction Noise reduction is possible with images exposed for 1 sec. or longer. 1 Select [Long exp. noise reduction]. Under the [z3] tab, select [Long exp. noise reduction], then press <0>. the desired setting. 2 SetSelect the desired setting, then press <0>. Auto For exposures of 1 sec. or longer, noise reduction is performed automatically if noise typical of long exposures is detected. This [Auto] setting is effective in most cases.
3 Setting Noise ReductionN With [Auto] and [Enable], the noise reduction process after the picture is taken may take the same amount of time as that for the exposure. During noise reduction, shooting is still possible as long as the maximum burst indicator in the viewfinder shows “1” or higher. Images taken at ISO 1600 or higher may look grainier with the [Enable] setting than with the [Disable] or [Auto] setting.
3 Highlight Tone PriorityN You can reduce overexposed, clipped highlights. 1 Select [Highlight tone priority]. Under the [z3] tab, select [Highlight tone priority], then press <0>. [Enable]. 2 Select Highlight details are improved. The dynamic range is expanded from the standard 18% gray to bright highlights. The gradation between the grays and highlights becomes smoother. picture. 3 TakeThetheimage will be recorded with highlight tone priority applied.
3 Correction of Lens Peripheral Illumination and Aberration Peripheral light fall-off is a phenomenon that makes the image corners look darker due to the lens characteristics. Color fringing along subject outlines is called chromatic aberration. This lens aberration and light fall-off can be corrected. By default, Peripheral illumination and Chromatic aberration correction are set to [Enable]. If [Cannot correct - no data] is displayed, see “Lens Correction Data” on the next page.
3 Correction of Lens Peripheral Illumination and Aberration Chromatic Aberration Correction 1 Select the setting. Check that [Correction data available] is displayed for the attached lens. Select [Chromatic aberration], then press <0>. Select [Enable], then press <0>. picture. 2 TakeThetheimage will be recorded with the chromatic aberration corrected. Lens Correction Data The camera already contains data for lens peripheral illumination correction and chromatic aberration correction for approx.
3 Correction of Lens Peripheral Illumination and Aberration Cautions for Lens Correction Peripheral illumination correction and chromatic aberration correction cannot be applied to JPEG images already taken. When using a non-Canon lens, setting the corrections to [Disable] is recommended, even if [Correction data available] is displayed.
3 Reducing FlickerN If you shoot an image with a fast shutter speed under a light source such as fluorescent light, the blinking of the light source causes flicker and the image may be vertically unevenly exposed. If continuous shooting is used under these conditions, uneven exposures or colors across the images may result. With anti-flicker shooting, the camera detects the frequency of the light source’s blinking and takes the picture when the flicker causes less effect on exposure or color.
3 Reducing FlickerN If the subject is against a dark background or if there is a bright light in the image, flicker may not be detected. Under certain special types of lighting, the camera may not be able to reduce the effects of the flicker even when is displayed. Depending on the light source, flicker may not be detected properly. If you recompose a shot, may appear and disappear intermittently.
3 Setting the Color SpaceN The range of reproducible colors is called “color space”. With this camera, you can set the color space for captured images to sRGB or Adobe RGB. For normal shooting, sRGB is recommended. The color space is set automatically to [sRGB] in the mode. 1 Select [Color space]. Under the [z2] tab, select [Color space], then press <0>. the desired color space. 2 SetSelect [sRGB] or [Adobe RGB], then press <0>.
3 Creating and Selecting a Folder You can freely create and select the folder where the captured images are to be saved. This operation is optional since a folder will be created automatically for saving captured images. Creating a Folder 1 Select [Record func+card/folder sel.]. Under the [51] tab, select [Record func+card/folder sel.], then press <0>. 2 Select [Folder]. 3 Select [Create folder]. [OK]. 4 Select X A new folder with the folder number increased by one is created.
3 Creating and Selecting a Folder Selecting a Folder Lowest file number Number of images in folder Select a folder on the folder selection screen, then press <0>. X The folder where the captured images will be saved is selected. Subsequently captured images will be recorded into the selected folder. Folder name Highest file number Folders As with “100EOS5D” for example, the folder name starts with three digits (the folder number) followed by five alphanumeric characters.
3 Changing the File Name The file name has four alphanumeric characters followed by a four-digit image (Example) BE3B0001.JPG number (p.199) and extension. The first four alphanumeric characters are set upon factory shipment and unique to the camera. However, you can change them. With “User setting1”, you can change and register the four characters as desired. With “User setting2”, if you register three characters, the fourth character from the left will be appended automatically to indicate the image size.
3 Changing the File Name Operate the <5> dial or <9> to move the and select the desired character. Then press <0> to enter it. the setting. 4 ExitAfter entering the correct number of characters, press the button, then select [OK]. X The registered file name will be saved. the registered file name. 5 Select Select [File name], then press <0>. Settings Select the registered file name, then press <0>. If User setting2 is registered, select “*** (the 3 characters registered) + image size”.
3 Changing the File Name The first character cannot be an underscore “_”. User setting2 When you select the “*** + image size” registered with User setting2 and take pictures, the image-recording quality character will be automatically appended as the file name’s fourth character from the left.
3 File Numbering Methods The four-digit file number is like the frame (Example) BE3B0001.JPG number on a roll of film. The captured images are assigned a sequential file number from 0001 to 9999 and saved in one folder. You can change how the file number is assigned. 1 Select [File numbering]. Under the [51] tab, select [File numbering], then press <0>. the file numbering method. 2 Select Select the desired setting, then press <0>.
3 File Numbering Methods Auto Reset Restarts the file numbering from 0001 each time the card is replaced or a new folder is created. When you replace the card, create a folder, or switch the target card (such as f9g), the file numbering continues in sequence from 0001 for the images saved. This is convenient if you want to organize images according to cards or folders.
3 Setting Copyright InformationN When you set the copyright information, it will be recorded to the image as Exif information. 1 Select [Copyright information]. Under the [54] tab, select [Copyright information], then press <0>. the option to be set. 2 Select Select [Enter author’s name] or [Enter copyright details], then press <0>. text. 3 Enter Press the button. The text palette will be highlighted with a color frame, and text can be entered.
3 Setting Copyright InformationN Checking the Copyright Information When you select [Display copyright info.] in step 2, you can check the [Author] and [Copyright] information that you entered. Deleting the Copyright Information When you select [Delete copyright information] in step 2 on the preceding page, you can delete the [Author] and [Copyright] information. If the entry for “Author” or “Copyright” is long, it may not be displayed entirely when you select [Display copyright info.].
5 Advanced Operations In the shooting modes, you can select the shutter speed, aperture, and other camera settings to change the exposure and obtain the desired result. A M icon at the upper right of a page title indicates a function that can be used only in the following modes: . After you press the shutter button halfway and let go, the exposure values will remain displayed in the viewfinder and on the LCD panel for 4 sec. (0).
d: Program AE The camera automatically sets the shutter speed and aperture to suit the subject’s brightness. This is called Program AE. * stands for Program. * AE stands for Auto Exposure. 1 Set the Mode Dial to . on the subject. 2 Focus Look through the viewfinder and aim the AF point over the subject. Then press the shutter button halfway. X When focus is achieved, the focus indicator in the viewfinder will light up (in One-Shot AF mode).
d: Program AE If the “30"” shutter speed and the lowest f/number blink, it indicates underexposure. Increase the ISO speed or use flash. If the “8000” shutter speed and the highest f/number blink, it indicates overexposure. Lower the ISO speed or use an ND filter (sold separately) to reduce the amount of light entering the lens. Differences Between and Modes In the mode, many functions, such as the AF operation and metering mode, are set automatically to prevent spoiled shots.
s: Shutter-Priority AE In this mode, you set the shutter speed and the camera automatically sets the aperture to obtain the standard exposure matching the brightness of the subject. This is called shutter-priority AE. A faster shutter speed can freeze the action of a moving subject. A slower shutter speed can create a blurred effect, giving the impression of motion. * stands for Time value. Blurred motion (Slow shutter speed: 1/30 sec.) 1 Frozen action (Fast shutter speed: 1/2000 sec.
s: Shutter-Priority AE If the lowest f/number blinks, it indicates underexposure. Turn the <6> dial to set a slower shutter speed until the aperture stops blinking or set a higher ISO speed. If the highest f/number blinks, it indicates overexposure. Turn the <6> dial to set a faster shutter speed until the aperture stops blinking or set a lower ISO speed. Shutter Speed Display The shutter speeds from “8000” to “4” indicate the denominator of the fractional shutter speed.
f: Aperture-Priority AE In this mode, you set the desired aperture and the camera sets the shutter speed automatically to obtain the standard exposure suiting the subject brightness. This is called aperture-priority AE. A higher f/number (smaller aperture hole) will make more of the foreground and background fall within acceptable focus. On the other hand, a lower f/number (larger aperture hole) will make less of the foreground and background fall within acceptable focus.
f: Aperture-Priority AE If the “30"” shutter speed blinks, it indicates underexposure. Turn the <6> dial to set a larger aperture (lower f/number) until the shutter speed blinking stops or set a higher ISO speed. If the “8000” shutter speed blinks, it indicates overexposure. Turn the <6> dial to set a smaller aperture (higher f/number) until the shutter speed blinking stops or set a lower ISO speed. Aperture Display The higher the f/number, the smaller the aperture opening will be.
a: Manual Exposure In this mode, you set both the shutter speed and aperture as desired. To determine the exposure, refer to the exposure level indicator in the viewfinder or use a commercially-available exposure meter. This method is called manual exposure. * stands for Manual. Shutter speed Aperture 1 Set the Mode Dial to . 2 Set the ISO speed (p.158). speed and aperture. 3 SetTothesetshutter the shutter speed, turn the <6> dial. To set the aperture, turn the <5> dial.
a: Manual Exposure Exposure Compensation with Auto ISO If the ISO speed is set to A (AUTO), you can set exposure compensation (p.214) as follows: • [z2: Expo.comp./AEB] • Under [83: Custom Controls], use [s: Expo comp (hold btn, turn )] (p.423). • Quick Control (p.61) If Auto ISO is set, the ISO speed setting will change to suit the shutter speed and aperture in order to obtain a standard exposure. Therefore, you may not obtain the desired exposure effect. In such a case, set the exposure compensation.
q Selecting the Metering ModeN You can select one of four methods to measure the subject brightness. In the mode, evaluative metering is set automatically. 1 Press the button. (9) the metering mode. 2 Select While looking at the LCD panel or in the viewfinder, turn the <6> dial. q:Evaluative metering w:Partial metering r:Spot metering e:Center-weighted average metering q Evaluative metering This is a general-purpose metering mode suited even for backlit subjects.
q Selecting the Metering ModeN r Spot metering This is for metering a specific spot of the subject or scene. Spot metering covers approx. 1.3% of the viewfinder area at the center. The spot metering circle will be displayed in the viewfinder. e Center-weighted average metering The metering is weighted at the center and then averaged for the entire scene. With q (Evaluative metering), the exposure setting will be locked when you press the shutter button halfway and focus is achieved (in One-Shot AF mode).
O Setting Exposure CompensationN Exposure compensation can brighten (increased exposure) or darken (decreased exposure) the standard exposure set by the camera. Exposure compensation can be set in the , , and shooting modes. Although you can set the exposure compensation up to ±5 stops in 1/3stop increments, the exposure compensation indicator in the viewfinder and on the LCD panel can only display the setting up to ±3 stops.
h Auto Exposure Bracketing (AEB)N By changing the shutter speed or aperture automatically, the camera brackets the exposure up to ±3 stops in 1/3-stop increments for three successive shots. This is called AEB. * AEB stands for Auto Exposure Bracketing. 1 Select [Expo.comp./AEB]. Under the [z2] tab, select [Expo.comp./AEB], then press <0>. the AEB range. 2 SetTurn the <6> dial to set the AEB AEB range range. If you turn <5>, you can set the exposure compensation. Press <0> to set it.
h Auto Exposure Bracketing (AEB)N During AEB, in the viewfinder and on the LCD panel will blink. If the drive mode is set to or , press the shutter button three times for each shot. When , , or is set and you hold down the shutter button completely, the three bracketed shots will be taken continuously and the camera will automatically stop shooting. When or is set, the three bracketed shots will be taken continuously after a 10-sec. or 2-sec. delay.
A AE LockN Use AE lock when the area of focus is to be different from the exposure metering area or when you want to take multiple shots at the same exposure setting. Press the button to lock the exposure, then recompose and take the picture. This is called AE lock. It is effective for backlit subjects, etc. 1 Focus on the subject. Press the shutter button halfway. X The exposure setting will be displayed. the button.
F: Bulb Exposures In this mode, the shutter stays open as long as you hold down the shutter button completely, and closes when you let go of the shutter button. This is called bulb exposure. Use bulb exposures for night scenes, fireworks, the heavens, and other subjects requiring long exposures. 1 Set the Mode Dial to . the desired aperture. 2 SetWhile looking at the LCD panel or the viewfinder, turn the <6> or <5> dial. Elapsed exposure time picture.
F: Bulb Exposures With [z3: Long exp. noise reduction], you can reduce the noise generated during long exposures (p.185). For bulb exposures, using a tripod and bulb timer is recommended. Using mirror lockup (p.234) with bulb exposures is also possible. You can also shoot bulb exposures by using Remote Switch RS-80N3 or Timer Remote Controller TC-80N3 (both sold separately, p.237). You can also use Remote Controller RC-6 (sold separately, p.237) for bulb exposures.
F: Bulb Exposures the desired exposure time. 3 SetSelect the hour, minute, or second. Press <0> so is displayed. Set the desired number, then press <0> (Returns to ). [OK]. 4 Select X The set time will be displayed on the menu screen. X When you exit the menu, will be displayed on the LCD panel. Elapsed exposure time the picture. 5 Take X Press the shutter button completely, and the bulb exposure will start and continue until the set time elapses.
w: HDR (High Dynamic Range) ShootingN Clipped highlights and shadows will be reduced for a high dynamic range of tones even with high-contrast scenes. HDR shooting is effective for landscape and still-life shots. With HDR shooting, three images of different exposures (standard exposure, underexposure, and overexposure) are captured continuously for each shot and then merged together automatically. The HDR image is recorded as a JPEG image. * HDR stands for High Dynamic Range. 1 Press the button.
w: HDR (High Dynamic Range) ShootingN Effects Natural For images preserving a wide tonal range where the highlight and shadow details would otherwise be lost. Clipped highlights and shadows will be reduced. Art standard While the clipped highlights and shadows will be reduced more than with [Natural], the contrast will be lower, and the gradation flatter to have the picture look like a painting. The subject outlines will have bright (or dark) edges.
w: HDR (High Dynamic Range) ShootingN [Continuous HDR]. 5 SetSelect either [1 shot only] or [Every shot], then press <0>. With [1 shot only], HDR shooting will be canceled automatically after the shooting ends. With [Every shot], HDR shooting continues until the setting in step 3 is set to [Disable HDR]. Image Align]. 6 SetFor[Auto handheld shooting, select [Enable]. When using a tripod, select [Disable], then press <0>. to be saved.
w: HDR (High Dynamic Range) ShootingN picture. 8 TakeHDRtheshooting is possible with viewfinder shooting and Live View shooting. X will be displayed on the LCD panel. When you press the shutter button completely, three consecutive images will be captured, and the HDR image will be recorded to the card. If the image-recording quality is set to RAW, the HDR image will be recorded in 73 quality. If the image-recording quality is set to RAW+JPEG, the HDR image will be recorded in the JPEG quality set.
w: HDR (High Dynamic Range) ShootingN When shooting HDR images with [Auto Image Align] set to [Enable], AF point display information (p.325) and Dust Delete Data (p.375) will not be appended to the image. If you perform handheld HDR shooting while [Auto Image Align] is set to [Enable], image periphery will be slightly cropped and resolution will be slightly lowered (except when shooting with [1.3x (crop)] or [1.6x (crop)]). Also, if the images cannot be aligned properly due to camera shake, etc.
P Multiple ExposuresN You can shoot two to nine exposures to be merged into one image. If you shoot multiple-exposure images with Live View shooting (p.255), you can see how the single exposures are being merged while shooting. 1 Press the button. Multiple exposure. 2 Select Select [P], then press <0>. X The multiple exposure setting screen will appear. [Multiple exposure]. 3 SetSelect [On:Func/Ctrl] or [On:ContShtng], then press <0>. To exit shooting multiple exposures, select [Disable].
P Multiple ExposuresN [Multi-expos ctrl]. 4 SetSelect the desired multiple-exposure control method, then press <0>. Additive The exposure of each single exposure is added cumulatively. Based on the [No. of exposures], set a negative exposure compensation. Refer to the basic guide below to set a negative exposure compensation. Exposure Compensation Setting Guide for Multiple Exposures Two exposures: -1 stop, three exposures: -1.5 stop, four exposures: -2 stops Average Based on the [No.
P Multiple ExposuresN to be saved. 6 SetTothesaveimages all the single exposures and the merged multiple-exposure image, select [All images], then press <0>. To save only the merged multipleexposure image, select [Result only], then press <0>. [Continue Mult-exp]. 7 SetSelect either [1 shot only] or [Continuously], then press <0>. With [1 shot only], multiple-exposure shooting will be canceled automatically after the shooting ends.
P Multiple ExposuresN subsequent exposures. 9 Shoot X When [On:Func/Ctrl] is set, the merged multiple-exposure image will be displayed. With Live View shooting, the multipleexposure images merged so far will be displayed. By pressing the button, you can display only the Live View image. After you shoot the set number of exposures, multiple-exposure shooting will exit.
P Multiple ExposuresN With multiple exposures, the more exposures there are, the more noticeable the noise, irregular colors, and banding will be. Also, as noise increases with higher ISO speeds, shooting at low ISO speeds is recommended. If [Additive], [Bright], or [Dark] is set, the image processing after taking the multiple exposures will take time. (The access lamp will light up longer.
P Multiple ExposuresN Merging Multiple Exposures with an Image Recorded on the Card You can select a 1 image recorded on the card as the first single exposure. The image data of the selected 1 image will remain intact. You can only select 1 images. You cannot select 41/61 or JPEG images. 1 Select [Select image for multi. expo.]. X The images on the card will be displayed. an image. 2 Select Turn the <5> dial to select the image to be used as the first single exposure, then press <0>. Select [OK].
P Multiple ExposuresN You can also select a 1 multiple-exposure image as the first single exposure. If you select [Deselect img], the selected image will be canceled. Checking and Deleting Multiple Exposures During Shooting When [On:Func/Ctrl] is set and you have not finished shooting the set number of exposures, you can press the button to view the merged multiple-exposure image so far. You can check how it looks and the exposure. (Not possible when [On:ContShtng] is set.
P Multiple ExposuresN FAQ Are there any restrictions on the image-recording quality? All JPEG image-recording quality settings can be selected. If 41 or 61 is set, the merged multiple-exposure will be a 1 image. Image-Recording Quality Setting Single Exposures Merged MultipleExposure JPEG JPEG JPEG 1 1 1 41/61 41/61 1 1+JPEG 1+JPEG 1+JPEG 41/61+JPEG 41/61+JPEG 1+JPEG Can I merge images recorded on the card? With [Select image for multi. expo.
2 Mirror LockupN Camera vibrations caused by the mirror’s reflex action when the picture is taken is called “mirror shock”. Mirror lockup keeps the mirror up before and while shooting to reduce blur caused by camera vibrations. Useful when shooting closeups (macro photography), using a super telephoto lens, and shooting at slow shutter speeds. 1 Select [Mirror lockup]. Under the [z4] tab, select [Mirror lockup], then press <0>. the desired setting.
2 Mirror LockupN Minimizing Blurred Photos Use a sturdy tripod suited for the camera weight. Mount the camera securely on the tripod. Using a remote switch or a remote controller is recommended (p.237). In addition to mirror lockup, Silent LV shooting (p.266) and Silent single shooting (p.142) are also effective. When using mirror lockup, setting [Shoot * sec. after press] is recommended. Selecting a longer time, such as [Shoot 2 sec. after press], will increase time before the shot, reducing mirror shock.
Using the Eyepiece Cover When you use the self-timer, bulb, or a remote switch and do not look through the viewfinder, stray light entering the viewfinder can cause the picture to look dark. To prevent this, use the eyepiece cover (p.35) attached to the camera strap. During Live View shooting and movie shooting, it is not necessary to attach the eyepiece cover. 1 Detach the eyecup. While grasping both sides of the eyecup, slide it upward to detach it. the eyepiece cover.
F Using a Remote Switch You can connect the Remote Switch RS-80N3 (sold separately) or Timer Remote Controller TC-80N3 (sold separately) or any EOS accessory equipped with an N3-type terminal to the camera for shooting (p.454). To operate the accessory, refer to its instruction manual. 1 Open the terminal cover. the plug to the remote 2 Connect control terminal. Connect the plug as shown in the illustration. To disconnect the plug, grasp the silver part and pull.
R Remote Control Shooting the self-timer. 4 Select While looking at the LCD panel or in the viewfinder, turn the <5> dial to select or . the remote controller’s 5 Press transmit button. Remote control sensor Point the remote controller toward the camera’s remote control sensor, and press the transmit button. X The self-timer lamp lights up and the picture is taken. Fluorescent or LED lighting may cause camera misoperation by triggering the shutter inadvertently.
H Interval Timer Shooting With the interval timer, you can set the shooting interval and the number of shots. The camera will repeat taking one shot with the set interval until the set number of shots are taken. 1 Select [Interval timer]. Under the [z4] tab (the [z2] tab in ), select [Interval timer], then press <0>. [Enable]. 2 Select Select [Enable], then press button. the interval and number of 3 Set shots. Select the hour, minute, second, or number of shots. Press <0> so is displayed.
H Interval Timer Shooting No. of shots Interval Interval timer [OK]. 4 Select X The interval timer settings will be displayed on the menu screen. X When you exit the menu, will be displayed on the LCD panel. the picture. 5 Take X Shooting will start according to the interval timer settings. During interval timer shooting, will blink. After the set number of shots are taken, the interval timer shooting will stop and be automatically canceled. Using a tripod is recommended.
H Interval Timer Shooting Do not point the camera toward an intense light source, such as the sun or an intense artificial light source. Doing so may damage the image sensor or the camera’s internal components. If the lens’s focus mode switch is set to , the camera will not shoot when focus is not achieved. Setting it to and focusing manually is recommended. Live View shooting, movie shooting, or bulb exposures cannot be performed with interval timer.
MEMO 242
6 Flash Photography This chapter explains how to shoot with external EXseries Speedlites (sold separately) and how to set Speedlite settings with the camera’s menu screen. Flash cannot be used with movie shooting. It will not fire. AEB cannot be used with flash.
D Flash Photography EOS-dedicated, EX-series Speedlites An EX-series Speedlite (sold separately) makes flash photography as easy as normal shooting. For detailed instructions, refer to the EX-series Speedlite’s instruction manual. This camera is a Type-A camera that can use all the features of EX-series Speedlites. To set the flash functions and flash Custom Functions with the camera’s menu, see pages 247-253.
D Flash Photography Canon Speedlites Other Than the EX-series With an EZ/E/EG/ML/TL-series Speedlite set to A-TTL or TTL autoflash mode, the flash can be fired at full output only. Set the camera’s shooting mode to (manual exposure) or (aperture-priority AE) and adjust the aperture setting before shooting. When using a Speedlite that has manual flash mode, shoot in the manual flash mode. Non-Canon Flash Units Sync Speed The camera can synchronize with non-Canon compact flash units at 1/200 sec.
D Flash Photography If the camera is used with a flash unit or flash accessory dedicated to another camera brand, the camera may not operate properly and malfunction may result. Do not connect to the camera’s PC terminal any flash unit with an output voltage of 250 V or more. Do not attach a high-voltage flash unit on the camera’s hot shoe. It may not fire. A flash unit attached to the camera’s hot shoe and a flash unit connected to the PC terminal can both be used at the same time.
3 Setting the FlashN With an EX-series Speedlite having compatible flash function settings, you can use the camera’s menu screen to set the Speedlite’s functions and Custom Functions. Attach the Speedlite to the camera and turn on the Speedlite before setting the flash functions. For details on the Speedlite’s functions, refer to the Speedlite’s instruction manual. 1 Select [External Speedlite control]. Under the [z1] tab, select [External Speedlite control], then press <0>.
3 Setting the FlashN Flash Sync. Speed in Av Mode You can set the flash-sync speed for flash photography in the aperture-priority AE (f) mode. : Auto The flash sync speed is set automatically within a range of 1/200 sec. to 30 sec. to suit the scene’s brightness. High-speed sync is also possible. : 1/200-1/60sec. auto Prevents a slow shutter speed from being set in low-light conditions. It is effective for preventing subject blur and camera shake.
3 Setting the FlashN Flash Function Settings The screen display and setting options will vary depending on the Speedlite model, current flash mode, Speedlite’s Custom Function settings, etc. To see which functions your Speedlite (sold separately) provides, refer to the Speedlite’s instruction manual.
3 Setting the FlashN Wireless functions / Flash ratio control Wireless (multiple) flash shooting is possible with radio or optical transmission. For details on wireless flash, refer to the instruction manual of a Speedlite compatible with wireless flash shooting. With a macro flash (MR-14EX II, etc.) compatible with flash function settings, you can set the flash ratio between flash tubes or flash heads A and B, or use wireless flash with slave units.
3 Setting the FlashN Shutter synchronization Normally, set this to [First-curtain synchronization] so that the flash fires immediately after the exposure starts. If [Second-curtain synchronization] is set, the flash will fire right before the shutter closes. When this is combined with a slow shutter speed, you can create a trail of light such as from car headlights at night with a more natural feel.
3 Setting the FlashN When using second-curtain synchronization, set the shutter speed to 1/25 sec. or slower. If the shutter speed is 1/30 sec. or faster, first-curtain synchronization will be applied automatically even if [Second-curtain synchronization] is set. With an EX-series Speedlite not compatible with flash function settings, you can only set the following: [Flash firing], [E-TTL II meter.], and [Flash exposure compensation] under [Flash function settings].
3 Setting the FlashN Flash Custom Function Settings For details on the Speedlite’s Custom Functions, refer to the Speedlite’s (sold separately) instruction manual. 1 Select [Flash C.Fn settings]. the desired functions. 2 SetSelect the number, then press <0>. Select the setting, then press <0>. With an EX-series Speedlite, if the [Flash metering mode] Custom Function is set to [TTL flash metering] (autoflash), the Speedlite will always fire at full output. Clear Settings 1 Select [Clear settings].
MEMO 254
7 Shooting with the LCD Monitor (Live View Shooting) You can shoot while viewing the picture on the camera’s LCD monitor. This is called “Live View shooting”. Live View shooting is enabled by setting the Live View shooting/ Movie shooting switch to . If you handhold the camera and shoot while viewing the LCD monitor, camera shake can cause blurred images. Using a tripod is recommended. Remote Live View Shooting With EOS Utility (EOS software, p.
A Shooting with the LCD Monitor 1 Set the Live View shooting/Movie shooting switch to . the Live View image. 2 Display Press the <0> button. X The Live View image will appear on the LCD monitor. The Live View image will closely match the brightness level of the actual image you capture. on the subject. 3 Focus When you press the shutter button halfway, the camera will focus with the current AF method (p.268). the picture. 4 TakePress the shutter button completely.
A Shooting with the LCD Monitor Enabling Live View Shooting Set [z5: Live View shoot.] (the [z3] tab in ) to [Enable]. Number of Possible Shots with Live View Shooting (Approx. number of shots) Temperature Room Temperature (23°C / 73°F) Low Temperatures (0°C / 32°F) Possible shots 220 210 The figures above are based on a fully-charged Battery Pack LP-E6N and CIPA (Camera & Imaging Products Association) testing standards.
A Shooting with the LCD Monitor Information Display Each time you press the button, the information display will change.
A Shooting with the LCD Monitor The histogram can be displayed when [z5: Expo. simulation: Enable] (p.265) is set. You can display the electronic level by pressing the button (p.75). Note that if the AF method is set to [u+Tracking] or the camera is connected to a TV set with an HDMI cable, the electronic level cannot be displayed. When is displayed in white, it indicates that the Live View image brightness is close to what the captured image will look like.
A Shooting with the LCD Monitor Scene Icons In the shooting mode, the camera detects the scene type and sets everything automatically to suit the scene. The detected scene type is indicated on the upper left of the screen. For certain scenes or shooting conditions, the icon displayed may not match the actual scene.
A Shooting with the LCD Monitor *5:Displayed with any of the lenses below: • EF300mm f/2.8L IS II USM • EF400mm f/2.8L IS II USM • EF500mm f/4L IS II USM • EF600mm f/4L IS II USM • Image Stabilizer lenses marketed in 2012 or later. *4+*5:If the conditions in both *4 and *5 are met, the shutter speed will slow down.
Shooting Function Settings Crop/Aspect You can perform crop shooting, or shoot with the set aspect ratio for Live View shooting. To set them with the menu, see page 154. To set them with the Quick Control screen, see the next page. If you use [83: Custom Controls] to assign [Switch between crop/aspect] to the button, you can just press the button while displaying Live View image to switch the Crop/aspect setting. For details, see page 423.
Shooting Function Settings Q Quick Control In the modes, the AF method, Drive mode, Metering mode, Crop/aspect ratio, Recording/playing back card and image quality, White balance, Picture Style, and Auto Lighting Optimizer can be set. In the mode, only the functions in bold above can be set. Press the button (7). X The settable functions will be displayed. 1 a function and set it. 2 Select Use <9> to select a function.
3 Menu Function Settings z5 When the Live View shooting/Movie shooting switch is set to , the Live View shooting menu options will appear under the [z5] and [z6] tabs (the [z3] tab in ). The settable functions on this menu screen apply only to Live View shooting. They do not work with viewfinder shooting (settings become invalid). Live View shooting You can set Live View shooting to [Enable] or [Disable]. AF method You can select [u+Tracking] or [FlexiZone - Single].
3 Menu Function Settings Grid display With [3x3 l] or [6x4 m], you can display grid lines to help you level the camera vertically or horizontally. Also, with [3x3+diag n], the grid is displayed together with diagonal lines to help you compose with better balance by aligning the intersections over the subject. Exposure simulationN Exposure simulation simulates and displays how the brightness of the actual image (exposure) will look.
3 Menu Function Settings z6 N Silent LV shootingN • Mode 1 You can suppress the camera noise when shooting. Continuous shooting is also possible. If is set, you can shoot at a maximum continuous shooting speed of approx. 5.0 fps. • Mode 2 When the shutter button is pressed completely, only one shot will be taken. While you keep holding down the shutter button, the camera operation will be suspended. Then when you return to the shutter button’s halfway position, the camera operation will resume.
3 Menu Function Settings Metering timerN You can change how long the exposure setting is displayed (AE lock time). Performing any of the following operations will stop Live View shooting. To start Live View shooting again, press the <0> button. • Selecting [z3: Dust Delete Data], [53: Sensor cleaning], [54: Clear all camera settings], or [54: zfirmware ver.].
Using AF to Focus (AF Method) Selecting the AF Method You can set the AF method to [u(face)+Tracking] (p.269) or [FlexiZone - Single] (p.271) to suit the shooting conditions or subject. If you want to achieve precise focus, set the lens’s focus mode switch to , magnify the image, and focus manually (p.275). Select the AF method. Under the [z5] tab (the [z3] tab in ), select [AF method]. Select the desired AF method, then press <0>.
Using AF to Focus (AF Method) u(face)+Tracking: c The camera detects and focuses on human faces. If a face moves, the AF point
also moves to track the face. 1 Display the Live View image. Press the <0> button. X The Live View image will appear on the LCD monitor. an AF point. 2 Select When a face is detected, the
frame will appear over the face to be focused on. If multiple faces are detected, will be displayed. Use <9> to move the frame over the face you want to focus on.
Using AF to Focus (AF Method) Focusing on a subject other than a human face Press <9> or <0> and the AF frame < > will appear in the center. Then use <9> to move the AF frame over the desired subject. Once the AF frame < > achieves focus, it will track the subject even if the subject moves or if you change the composition. If the subject’s face is significantly out of focus, face detection will not be possible. Adjust the focus manually (p.275) so that the face can be detected, then perform AF.
Using AF to Focus (AF Method) FlexiZone - Single: d The camera focuses with a single AF point. This is effective when you want to focus on a particular subject. the Live View image. 1 Display Press the <0> button. X The Live View image will appear on the LCD monitor. X The AF point < > will appear. AF point the AF point. 2 Move Use <9> to move the AF point to where you want to focus. (It cannot be moved to the edge of the screen.
Using AF to Focus (AF Method) The size of the AF point varies depending on the setting of [z4: Crop/ aspect ratio]. During movie shooting, if [Movie Servo AF] is set to [Enable], the AF point will be displayed in a larger size. Notes for AF AF Operation Even when focus is achieved, pressing the shutter button halfway will focus again. The image brightness may change during and after the AF operation.
Using AF to Focus (AF Method) Shooting Conditions that Make Focusing Difficult Subject with low-contrast such as the blue sky, solid-color flat surfaces or when highlight or shadow details are clipped. Subjects in low light. Stripes and other patterns where there is contrast only in the horizontal direction. Subjects with repetitive patterns (Example: Skyscraper windows, computer keyboards, etc.). Fine lines and subject outlines. Under a light source whose brightness, color, or pattern keeps changing.
Using AF to Focus (AF Method) Magnified View for FlexiZone - Single With [FlexiZone - Single], pressing the button will magnify the image to check the focus in the following sequence: approx. 6x, then approx. 16x. The image will be magnified at the AF point. If you press the shutter button halfway, AF will be performed in the magnified view. If focusing is difficult in the magnified view, return to the normal view and perform AF. Magnified view is not possible with [u +Tracking].
MF: Focusing Manually You can magnify the image and focus precisely with MF (manual focus). 1 Set the lens’s focus mode switch to . Turn the lens’s focusing ring to focus roughly. the magnifying frame. 2 Display Press the button. X The magnifying frame will appear. Magnifying frame the magnifying frame. 3 Move Use <9> to move the magnifying frame to the position where you want to focus. Pressing <9>, <0>, or button will return the magnifying frame to the screen’s center. the image.
MF: Focusing Manually manually. 5 Focus While looking at the magnified image, turn the lens’s focusing ring to focus. After achieving focus, press the button to return to the normal view. the picture. 6 TakeCheck the exposure, then press the shutter button completely to take the picture (p.256). If [z4: Crop/aspect ratio] is set to [1.3x (crop)] or [1.6x (crop)], [X1.3] or [X1.6] will be displayed when starting the magnified view. When [1.3x (crop)] or [1.
General Live View Shooting Cautions Image Quality When you shoot at high ISO speeds, noise (such as dots of light and banding) may become noticeable. Shooting in high temperatures may cause noise and irregular colors in the image. If Live View shooting is used continuously for a prolonged period, the camera’s internal temperature may rise, and image quality may deteriorate. Always exit Live View shooting when you are not shooting.
General Live View Shooting Cautions Live View Image Under low- or bright-light conditions, the Live View image may not reflect the brightness of the captured image. Even if a low ISO speed is set, noise may be noticeable in the displayed Live View image under low light. However, when you shoot, the image recorded will have less noise. (The image quality of the Live View image is different from that of the recorded image.) If the light source (illumination) within the image changes, the screen may flicker.
8 Shooting Movies Movie shooting is enabled by setting the Live View shooting/ Movie shooting switch to . For cards that can record movies, see page 5. If you handhold the camera and shoot movies, camera shake can cause blurred movies. Using a tripod is recommended. Full HD 1080 Full HD 1080 indicates compatibility with HighDefinition featuring 1080 vertical pixels (scanning lines).
k Shooting Movies / Autoexposure Shooting When the shooting mode is set to , , or , autoexposure control will take effect to suit the scene’s current brightness. Exposure control will be the same for all the shooting modes. the Mode Dial to , , 1 orSet. the Live View shooting/Movie 2 Set shooting switch to . X The reflex mirror will make a sound, then the image will appear on the LCD monitor. on the subject. 3 Focus Before shooting a movie, focus with AF or manual focus (p.268-276).
k Shooting Movies Shutter-priority AE When the shooting mode is , you can manually set the shutter speed for movie shooting. The ISO speed and aperture will be set automatically to suit the brightness and obtain a standard exposure. 1 Set the Mode Dial to . the Live View shooting/Movie 2 Set shooting switch to . the desired shutter speed. 3 SetWhile looking at the LCD monitor, Shutter speed turn the <6> dial. The settable shutter speeds depend on the frame rate. • 6 5 4: 1/4000 sec.
k Shooting Movies Aperture-priority AE When the shooting mode is , you can manually set the aperture for movie shooting. The ISO speed and shutter speed will be set automatically to suit the brightness and obtain a standard exposure. 1 Set the Mode Dial to . the Live View shooting/Movie 2 Set shooting switch to . the desired aperture. 3 SetWhile looking at the LCD monitor, turn the <6> dial. Aperture and shoot the movie.
k Shooting Movies ISO Speed in the Mode The ISO speed will be set automatically within ISO 100 - ISO 6400. ISO Speed in the , , , and Modes The ISO speed will be set automatically within ISO 100 - ISO 6400. Under [z2: ISO speed settings], if you set the [ISO speed range]’s [Maximum] setting to [H (12800)] in the , , or mode (p.161), the automatic ISO range will be expanded to H (equivalent to ISO 12800).
k Shooting Movies Notes for , < d>, , , and Modes In the mode, the scene icon for the scene detected by the camera is displayed on the upper left of the screen (p.285). You can lock the exposure (AE lock) by pressing the button (except in the mode, p.217). The exposure setting will be displayed for the time length set with [z6: Metering timer]. After applying AE lock during movie shooting, you can cancel it by pressing the button.
k Shooting Movies Scene Icons During movie shooting in the mode, an icon representing the scene detected by the camera will be displayed, and the shooting will be adapted to that scene. For certain scenes or shooting conditions, the icon displayed may not match the actual scene.
k Shooting Movies Manual Exposure Shooting You can manually set the shutter speed, aperture, and ISO speed for movie shooting. Using manual exposure to shoot movies is for advanced users. 1 Set the Mode Dial to . the Live View shooting/Movie 2 Set shooting switch to . the ISO speed. 3 SetPress the button. X The ISO speed setting screen will appear on the LCD monitor. Turn the <6> dial to set the ISO speed. For details on the ISO speed, see the next page. the shutter speed and 4 Set aperture.
k Shooting Movies and shoot the movie. 5 Focus The procedure is the same as steps 3 and 4 for “Autoexposure Shooting” (p.280). ISO Speed in the Mode With [Auto] (A), the ISO speed will be set automatically within ISO 100 - ISO 6400. Under [z2: ISO speed settings], if you set [ISO speed range]’s [Maximum] setting to [H (12800)] (p.161), the automatic ISO range will not expand to the H maximum.
k Shooting Movies If [Minimum] is set to [L(50)] in [ISO speed range], and you switch from still photo shooting to movie shooting, the minimum setting for manual ISO range for movie shooting will be ISO 100. It cannot be expanded to ISO 50. Changing the shutter speed or aperture during movie shooting is not recommended since the changes in the exposure will be recorded. When shooting a movie of a moving subject, a shutter speed of 1/30 sec. to 1/125 sec. is recommended.
k Shooting Movies Information Display Each time you press the button, the information display will change.
k Shooting Movies You can display the electronic level by pressing the button (p.75). Note that if the AF method is set to [u +Tracking] or the camera is connected to a TV set with an HDMI cable (p.351), the electronic level cannot be displayed. The electronic level, grid lines, or histogram cannot be displayed during movie shooting. (The display will disappear when you start shooting a movie.) When movie shooting starts, the movie shooting remaining time will change to the elapsed time.
k Shooting Movies Notes for Movie Shooting Movie-related settings are under the [z4] and [z5] tabs (p.313). In the mode, they are under the [z2] and [z3] tabs. A movie file is recorded each time you shoot a movie. If the file size exceeds 4 GB, a new file will be created for every subsequent approx. 4 GB. The movie image’s field of view is approx. 100% (when the movie recording size is set to L). You can also focus on the image by pressing the button.
k Shooting Movies Final Image Simulation The final image simulation shows the results of the current settings for Picture Style, white balance and other functions in the image so you can see what the captured image will look like. During movie shooting, the image displayed will automatically show the effects of the settings listed below. Final Image Simulation for Movie Shooting Picture Style * Sharpness (Strength), contrast, color saturation, and color tone will be reflected.
k Shooting Movies Shooting Still Photos While shooting a movie, you can also take a still photo by pressing the shutter button completely. Taking Still Photos During Movie Shooting If you take a still photo during movie shooting, the movie will record a still moment lasting approx. 1 sec. The captured still photo will be recorded to the card, and the movie shooting will resume automatically when the Live View image is displayed. The movie and still photo will be recorded as separate files on the card.
k Shooting Movies If [z5: V button function] is set to [ /k] or [q/k] (p.316), you cannot take still photos. Still photo shooting during movie shooting will have approx. 100% coverage with L, w, and x (when the image-recording quality is set to JPEG 73). AEB cannot be used. Even if a flash is used, it will not fire. Continuous still photo shooting is possible during movie shooting. However, the captured images will not be displayed on the screen.
Shooting Function Settings B/R/f/i/A Settings If you press the , , , or button while the image is displayed on the LCD monitor, the setting screen will appear on the LCD monitor and you can turn the <6> or <5> dial to set the respective function. During manual-exposure shooting (p.286), you can press the button to set the ISO speed. By pressing the button and then the button, you can set WB shift and WB bracketing.
Shooting Function Settings Q Quick Control In the , , , , and modes, the AF method, Drive mode, Movie recording size, Recording level (set manually only), Recording/playing back card and image quality (still photos), White balance, Picture Style, and Auto Lighting Optimizer can be set. In the mode, only the functions in bold above can be set. 1 Press the button (7). X The settable functions will be displayed. a function and set it. 2 Select Use <9> to select a function.
3 Setting the Movie Recording Size With [z4: Movie rec. size] (the [z2] tab in ), you can set the movie’s image size, frame rate (frames per sec.), and compression method. The frame rate displayed on the [Movie rec. size] screen switches automatically depending on the [53: Video system] setting (p.467). Image Size L 1920x1080 Full High-Definition (Full HD) recording quality. The aspect ratio is 16:9. w 1280x720 High-Definition (HD) recording quality. The aspect ratio is 16:9.
3 Setting the Movie Recording Size Compression Method W ALL-I (For editing/I-only) Compresses one frame at a time for recording. Although the file size is larger than with IPB (Standard), the movie is more suited for editing. X IPB (Standard) Compresses multiple frames at a time efficiently for recording. Since the file size is smaller than with ALL-I (For editing), you can shoot longer (with a card of the same capacity). Total Movie Recording Time and File Size Per Minute (Approx.
3 Setting the Movie Recording Size Movie Files Exceeding 4 GB Even if you shoot a movie exceeding 4 GB, you can keep shooting without interruption. During movie shooting, approx. 30 sec. before the movie reaches the 4 GB file size, the elapsed shooting time or time code displayed in the movie-shooting screen will start blinking. If you keep shooting until the movie file size exceeds 4 GB, a new movie file will be created automatically and the elapsed shooting time or time code will stop blinking.
3 Setting the Sound Recording You can shoot movies while recording sound with the built-in monaural microphone or the Directional Stereo Microphone DM-E1 (sold separately). You can also freely adjust the soundrecording level. Sound-recording settings are under [z4: Sound recording] (the [z2] tab in ). Sound Recording/Sound-Recording Level Auto Manual Disable 300 : The sound-recording level is adjusted automatically. Auto level control will operate automatically in response to the sound level.
3 Setting the Sound Recording Wind Filter/Attenuator Wind filter Attenuator : When [Enable] is set, it reduces the wind noise when recording outdoors. This feature takes effect only with the built-in microphone. Note that [Enable] reduces low bass sounds, so set it to [Disable] when there is no wind. It will record a more natural sound than with [Enable]. : Automatically suppresses sound distortion caused by loud noises. Even if [Sound rec.
3 Silent ControlN You can change the settings of the ISO speed, sound-recording level, etc. without making too much noise while shooting a movie. When [z5: Silent Control] is set to [Enable h], you can use the touch pad on the inner ring of the Quick Control Dial. You can just touch the top, bottom, left, or right of for silent operation. During movie shooting, you can press the button to display the Quick Control screen and change the functions below with .
3 Setting the Time Code The time code is a time reference recorded automatically to synchronize the movie during movie shooting. It is recorded at all times in the following units: hours, minutes, seconds, and frames. It is mainly used during movie editing. Use [z5: Time code] (the [z3] tab in ) to set the time code. Count Up Rec run Free run : The time code counts up only while you are shooting a movie. The time code will continue in the sequence of the movie files captured.
3 Setting the Time Code Movie Recording Count You can select what to display on the movie shooting screen. Rec time Time code : Indicates the elapsed time from the start of the movie shooting. : Indicates the time code during movie shooting. Movie Playback Count You can select what to display on the movie playback screen. Rec time Time code : Displays the recording time and playback time during movie playback. : Displays the time code during movie playback.
3 Setting the Time Code Drop Frame If the frame rate setting is 6 (29.97 fps) or 8 (59.94 fps), the time code’s frame count causes a discrepancy between the actual time and time code. This discrepancy can be corrected automatically. This correction function is called “drop frame.” Enable : The discrepancy is corrected automatically by skipping time code numbers (DF: Drop frame). Disable : The discrepancy is not corrected (NDF: Non-drop frame).
a Shooting Time-lapse Movies Still photos shot at a set interval can be stitched together automatically to create a time-lapse movie. A time-lapse movie shows how a subject changes in a much shorter period of time than the actual time it took. It is effective for a fixed-point observation of changing scenery, growing plants, celestial motion, etc. Time-lapse movies are recorded in L 6 W (NTSC) or L 5 W (PAL). The frame rate will be switched automatically according to the [53: Video system] setting (p.467).
a Shooting Time-lapse Movies the shooting interval and 5 Set number of shots. Time required Playback time Check the [k: Time required] and [3: Playback time] displayed at the bottom of the screen to set the shooting interval and number of shots. Select the number to be set (hours: minutes: seconds / Number of shots). Press <0> so is displayed. Set the desired number, then press <0>. (Returns to ). Shooting interval Settable from [00:00:01] to [99:59:59].
a Shooting Time-lapse Movies Card- time left The total length of a time-lapse movie that can be recorded on the card based on its remaining capacity. the menu. 8 ExitPress the button to turn off the menu screen. the message. 9 Read Read the message and select [OK]. shots. 10 TakeSettest the exposure and shooting functions, and press the shutter button halfway to focus as you do with Live View shooting. Press the shutter button completely to start taking test shots.
a Shooting Time-lapse Movies the time-lapse movie. 12 Shoot Press the shutter button halfway to Shots remaining Time-lapse movie check the focus and exposure. Press the shutter button completely to start shooting the time-lapse movie. AF will not work during time-lapse movie shooting. The exposure setting for the first shot will be applied to subsequent shots. During time-lapse movie shooting, nothing will be displayed on the LCD monitor. will blink on the LCD panel.
a Shooting Time-lapse Movies With time-lapse movie set to [Enable], you cannot set [z4: Movie rec. size] and [53: Video system]. If the camera is connected to a computer or printer with the interface cable, or if an HDMI cable is connected to the camera, you cannot select [Enable]. The maximum ISO speed will be ISO 3200 in the , , , and modes, and mode with Auto ISO set. Bulb exposure cannot be performed. If the shooting mode is , the operation will be the same as the mode.
a Shooting Time-lapse Movies If the time it takes to record to the card exceeds the interval between shots due to the shooting functions set or card performance, some of the shots may not be taken with the set intervals. The captured images are not recorded as still photos. Even if you cancel the time-lapse movie shooting after only one shot is taken, it will be recorded as a movie file. If the card does not have enough free space to record the set number of shots, [Playback time] will be displayed in red.
a Shooting Time-lapse Movies You can perform time-lapse movie shooting with a fully-charged Battery Pack LP-E6N for the durations (from start of shooting until the battery is exhausted) listed in the table below. Total Possilbe Time for Time-lapse Movie Shooting Room Temperature (23°C / 73°F) Low Temperatures (0°C / 32°F) Shooting interval: 1sec. 2 hr. 15 min. 2 hr. 10 min. Shooting interval: 10sec. 4 hr. 5 min. 3 hr. 55 min. If you use Remote Controller RC-6 (sold separately, p.
3 Menu Function Settings z4 When the Live View shooting/Movie shooting switch is set to , the movie shooting menu options will appear under the [z4] and [z5] tabs (the [z2] and [z3] tabs in ). Movie Servo AF During movie shooting, the camera focuses on the subject continuously. The default setting is [Disable]. When [Enable] is set: y The camera focuses on the subject continuously even when you are not pressing the shutter button halfway.
3 Menu Function Settings y If you want to keep the focus at a specific point or you do not want the lens operation noise to be recorded, you can temporarily stop Movie Servo AF by pressing the button assigned to [Pause Movie Servo AF] or [AF stop] under [83: Custom controls]. When you stop Movie Servo AF, the AF point will turn gray. • Under [83: Custom controls], if a button is assigned to [Pause Movie Servo AF] (p.421), Movie Servo AF will stop while holding down that button.
3 Menu Function Settings AF method You can select [u+Tracking] or [FlexiZone - Single] (p.269-272). Grid display With [3x3 l] or [6x4 m], you can display grid lines to help you level the camera vertically or horizontally. Also, with [3x3+diag n], the grid is displayed together with diagonal lines to help you compose with better balance by aligning the intersections over the subject. Note that the grid is not displayed during movie shooting.
3 Menu Function Settings Metering timerN You can change how long the exposure setting is displayed (AE lock time). Time code You can set the time code. For details, see pages 303-305. Silent ControlN When [Enable h] is set, you can use the touch pad and Quick Control screen to change settings silently during movie shooting. For details, see page 302. V button functionN You can set the functions performed by pressing the shutter button halfway or completely during movie shooting.
General Movie Shooting Cautions White and Red Internal Temperature Warning Icons If the camera’s internal temperature increases due to prolonged movie shooting or under a high ambient temperature, a white or red icon will appear. The white icon indicates that the image quality of still photos will deteriorate. It is recommended that you stop still photo shooting for a while and allow the camera to cool down. Since movie image quality will hardly be affected, you can still shoot movies.
General Movie Shooting Cautions Recording and Image Quality If you use a card with a slow writing speed, a five-level indicator may appear on the right of the screen during movie shooting. It indicates how much data has not yet been written to the card (remaining capacity of the internal buffer memory). The slower the card, the faster the indicator will climb upward. If the indicator Indicator becomes full, movie shooting will stop automatically.
9 Image Playback This chapter explains how to play back or erase photos and movies, how to display them on a TV screen, and other playback-related functions. Images shot and saved with another device The camera may not be able to properly display images captured with a different camera, edited with a computer, or that have had their file names changed.
x Image Playback Single-Image Display 1 Play back the image. Press the button. X The last image captured or played back will appear. an image. 2 Select To play back images starting with the last image captured, turn the <5> dial counterclockwise. To play back images starting with the first captured image, turn the dial clockwise. Each time you press the button, the information display will change.
x Image Playback the image playback. 3 ExitPress the button to exit the image playback and return to shooting-ready state. Shooting Information Display With the shooting information screen displayed (p.320), you can tilt <9> up or down to change the shooting information displayed at the screen’s bottom as follows. For details, see pages 323-324.
B: Shooting Information Display Sample Information for Still Photos Basic information display Eye-Fi transfer completed Eye-Fi card transmission status Battery level Rating Protect images Card Folder number File number Playback number/ Total images recorded Shutter speed Image-recording quality/Edited images/Cropping Aperture Highlight tone priority Exposure compensation amount ISO speed If the image was taken by another camera, certain shooting information may not be displayed.
B: Shooting Information Display Shooting information display • Detailed information Exposure compensation amount Aperture Histogram (Brightness/RGB) Shooting date and time Shutter speed ISO speed Shooting mode/ Multiple exposure Scroll bar Highlight tone priority White balance Metering mode File size Auto Lighting Optimizer White balance correction/ Correction amount AF Microadjustment Flash exposure compensation amount/HDR shooting/ Multi Shot Noise Reduction Crop Image-recording quality/ Edited
B: Shooting Information Display • Lens/Histogram information Histogram display (Brightness) Lens name Histogram display (RGB) Focal length • White balance information • Picture Style information 1 • Picture Style information 2 • Color space / Noise reduction information • Lens aberration correction information If you used GPS Receiver GP-E2 to record GPS information for the image, tilt <9> up or down to view the “GPS information” screen.
B: Shooting Information Display Sample Movie Information Display Movie playback Aperture Shutter speed ISO speed Movie shooting mode/ Time-lapse movie File size Movie recording size Frame rate Recording time/Time code Compression method • < > and < > modes: Shutter speed, aperture and ISO speed are not displayed. • < > mode: Aperture and ISO speed are not displayed. • < > mode: Shutter speed and ISO speed are not displayed. • < > mode + Auto ISO: ISO speed is not displayed.
B: Shooting Information Display Histogram The brightness histogram shows the exposure level distribution and overall brightness. The RGB histogram is for checking the color saturation and gradation. The display can be switched with [33: Histogram disp.]. [Brightness] Display Sample Histograms This histogram is a graph showing the distribution of the image’s brightness level.
x Searching for Images Quickly H Display Multiple Images on One Screen (Index Display) You can search for images quickly with the index display showing 4, 9, 36, or 100 images on one screen. 1 Press the button. During image playback or when the camera is ready to shoot, press the button. X [6u] will be displayed on the lower right of the screen. to the index display. 2 Switch Turn the <6> dial counterclockwise. X The 4-image index display will appear.
x Searching for Images Quickly I Jump through Images (Jump Display) In the single-image display, you can turn the <6> dial to jump through the images forward or backward according to the jump method set. 1 Select [Image jump w/6]. Under the [32] tab, select [Image jump w/6], then press <0>. the jump method. 2 Select Select the jump method, then press <0>.
x Searching for Images Quickly by jumping. 3 Browse Press the button to play back Jump method images. In the single-image display, turn the <6> dial. X You can browse by the method that was set. Playback position To search images by shooting date, select [Date]. To search images by folder, select [Folder]. If the card contains both movies and still photos, select [Movies] or [Stills] to display one or the other.
u Magnifying Images You can magnify a captured image by approx. 1.5x to 16x on the LCD monitor. 1 Magnified area position Magnify the image. The image can be magnified as follows: 1. During image playback (single-image display), 2. During the image review after image capture, and 3. From the shooting-ready state. Press the button. X The magnified view will appear. The magnified area and [6u] will be displayed on the lower right of the screen.
u Magnifying Images 3 Magnification Settings Under the [33] tab, when you select [Magnificatn (apx)], you can set the starting magnification and initial position for the magnified view. 1x (no magnification) The image is not magnified. The magnified view will start with the single-image display. 2x, 4x, 8x, 16x (magnify from center) The magnified view starts at the image center at the selected magnification. Actual size (from selected point) The recorded image’s pixels will be displayed at approx. 100%.
X Comparing Images (Two-Image Display) You can compare two images side by side on the LCD monitor. In the two-image display, you can use magnified view or jump display as well as protection, rating and erasure of images. 1 Set the two-image display. During image playback, press the button. X The two-image index display will appear. The currently-selected image will be highlighted with an orange frame. the images to be 2 Select compared. Pressing <0> switches the orange frame between the two images.
b Rotating the Image You can rotate the displayed image to the desired orientation. 1 Select [Rotate image]. Under the [31] tab, select [Rotate image], then press <0>. an image. 2 Select Turn the <5> dial to select the image to be rotated. You can also select an image in the index display (p.327). the image. 3 Rotate Each time you press <0>, the image will rotate clockwise as follows: 90° 9 270° 9 0°. To rotate another image, repeat steps 2 and 3. If you set [51: Auto rotate] to [OnzD] (p.
K Protecting Images You can protect important images from being accidentally erased by the camera’s erase function. 3 Protecting a Single Image 1 Select [Protect images]. Under the [31] tab, select [Protect images], then press <0>. [Select images]. 2 Select X An image will be displayed. Image protection icon an image. 3 Select Turn the <5> dial to select the image to be protected. You can also select an image or movie on the index display (p.327). the image.
K Protecting Images 3 Protecting All Images in a Folder or on a Card You can protect all the images in a folder or on a card at once. When you select [All images in folder] or [All images on card] in [31: Protect images], all the images in the folder or on the card will be protected. To cancel the image protection, select [Unprotect all images in folder] or [Unprotect all images on card]. If you format the card (p.67), the protected images will also be erased. Movies can also be protected.
K Protecting Images Protecting Images with the Button During image playback, you can use the button to protect an image. 1 Select [m btn function]. Under the [53] tab, select [m button function], then press <0>. 2 Select [Protect]. an image. 3 Select Press the button to play back images. Turn the <5> dial to select the image to be protected. You can also select an image or movie on the index display (p.327). the image.
Setting Ratings You can rate images (still photos and movies) with one of the five rating marks: l/m/n/o/p. This function is called rating. Rating Images with the Button 1 Select an image. During image playback, turn the <5> dial to select an image or movie to be rated. You can also select an image or movie on the index display (p.327). 2 RateEachthetimeimage. you press the button, the rating mark will change: l/m/n/o/p/None. To rate another image, repeat steps 1 and 2.
Setting Ratings 3 Setting Ratings with the Menu 1 Select [Rating]. Under the [32] tab, select [Rating], then press <0>. an image. 2 Select Turn the <5> dial to select an image or movie to be rated. If you press the button and turn the <6> dial counterclockwise, you can select an image from a threeimage display. To return to the singleimage display, turn the <6> dial clockwise. the image. 3 RatePress <0> and a blue highlight frame will appear as shown in the screenshot.
Setting Ratings A total of up to 999 images of a given rating can be displayed. If there are more than 999 images with a given rating, [###] will be displayed. Taking Advantage of Ratings With [32: Image jump w/6], you can display only images having the specified rating. With [32: Slide show], you can play back only images with a specific rating. With Digital Photo Professional (EOS software, p.520), you can select only the image with a specific rating (still photos only). With Windows 8.
Q Quick Control for Playback During playback, you can press the button to set the following: [J: Protect images], [b: Rotate image], [9: Rating], [R: RAW image processing (RAW images only)], [S: Resize (JPEG image only)], [N: Cropping (JPEG images only)], [ : Highlight alert], [ : AF point display], and [e: Image jump w/6]. For movies, only the functions in bold above can be set. 1 Press the button. During image playback, press the button. X The Quick Control options will appear.
Q Quick Control for Playback To rotate an image, set [51: Auto rotate] to [OnzD]. If [OnD] or [Off] is set, the [b Rotate image] setting will be recorded to the image, but the camera will not rotate the image for display. Pressing the button during the index display will switch to the single-image display and the Quick Control screen will appear. Pressing the button again will return to the index display. For images taken with another camera, the options you can select may be restricted.
k Enjoying Movies You can play back movies in the following three ways: Playback on a TV Set (p.351) By connecting the camera to a TV set with HDMI Cable HTC-100 (sold separately), you can play back the camera’s still photos and movies on the TV set. Since hard disk recorders do not have an HDMI IN port, the camera cannot be connected to a hard disk recorder with an HDMI cable.
k Enjoying Movies Playback and Editing with a Computer To play back or edit a movie, use preinstalled or general-purpose software, compatible with the movie’s recording format. If you play back or edit a movie with commercially-available software, use software compatible with MOV-format movies. For details on commerciallyavailable software, contact the software manufacturer.
k Playing Back Movies 1 Play back the image. Press the button to display an image. a movie. 2 Select Turn the <5> dial to select the movie to be played. With the single-image display, the icon displayed on the upper left indicates a movie. In the index display, perforations at the left edge of a thumbnail indicate a movie. As movies cannot be played from the index display, press <0> to switch to the single-image display. the single-image display, press 3 In<0>.
k Playing Back Movies Movie Playback Panel Operation Playback Description 7 Play Pressing <0> toggles between play and stop. 8 Slow motion Adjust the slow motion speed by turning the <5> dial. The slow motion speed is indicated on the upper right of the screen. 5 First frame Displays the movie’s first frame. 3 Previous frame Each time you press <0>, the previous frame is displayed. If you hold down <0>, it will rewind the movie.
X Editing a Movie’s First and Last Scenes You can edit out the first and last scenes of a movie in approx. 1-sec. increments. You can also edit time-lapse movies. 1 On the movie playback screen, select [X]. X The movie editing panel will be displayed at the bottom of the screen. the part to be edited out. 2 Specify Select either [U] (Cut beginning) or [V] (Cut end), then press <0>. Tilt <9> to the left or right to see the previous or next frames.
X Editing a Movie’s First and Last Scenes the edited movie. 4 Save Select [W], then press <0>. X The save screen will appear. To save it as a new movie, select [New file]. To save it and overwrite the original movie file, select [Overwrite], then press <0>. On the confirmation dialog, select [OK] to save the edited movie and return to the movie playback screen. Since the editing is performed in approx. 1-sec.
3 Slide Show (Auto Playback) You can play back the images on the card as an automatic slide show. 1 Number of images to be played back Select [Slide show]. Under the [32] tab, select [Slide show], then press <0>. the images to be played 2 Select back. Select the desired option on the screen, then press <0>. All images/Movies/Stills/Protect Select one of the following: [jAll images] [kMovies] [zStills] [JProtect]. Then press <0>.
3 Slide Show (Auto Playback) Item Playback Description jAll images All the still photos and movies on the card will be played back. iDate Still photos and movies taken on the selected shooting date will be played back. nFolder Still photos and movies in the selected folder will be played back. kMovies Only the movies on the card will be played back. zStills Only the still photos on the card will be played back.
3 Slide Show (Auto Playback) the slide show. 4 StartSelect [Start], then press <0>. X After [Loading image...] is displayed, the slide show will start. slide show. 5 ExitTothe exit the slide show and return to the setting screen, press the button. To pause the slide show, press <0>. During pause, [G] will be displayed on the upper left of the image. Press <0> again to resume the slide show. During auto playback, you can press the button to change the still photo display format (p.320).
Viewing Images on a TV Set By connecting the camera to a TV set with an HDMI cable (sold separately), you can play the camera’s still photos and movies on the TV set. For the HDMI cable, HDMI Cable HTC-100 (sold separately) is recommended. If the picture does not appear on the TV screen, set the [53: Video system] correctly to [For NTSC] or [For PAL] (depending on the video system of your TV set). 1 Connect the HDMI cable to the camera.
Viewing Images on a TV Set Adjust movie sound volume with the TV set. The sound volume cannot be adjusted with the camera. Before connecting or disconnecting the cable between the camera and TV set, turn off the camera and TV set. Depending on the TV set, part of the image displayed may be cut off. Do not connect any other device’s output to the camera’s terminal. Doing so may cause a malfunction. Certain TV sets may not be able to display the captured movies.
Viewing Images on a TV Set the camera’s button. 3 Press X An image will appear on the TV screen and you can use the TV set’s remote control to play back images. an image. 4 Select Point the remote control toward the TV set and press the / button to select an image. Still photo playback menu the remote control’s Enter 5 Press button.
a Copying Images The images recorded on one card can be copied to another card. 3 Copying a Single Image 1 Select [Image copy]. Under the [31] tab, select [Image copy], then press <0>. [Sel.Image]. 2 Select Check the copy source and target cards’ number, and remaining capacity. Select [Sel.Image], then press <0>. Lowest file number Number of images in folder the folder. 3 Select Select the folder containing the image you want to copy, then press <0>.
a Copying Images Total images selected the images to be copied. 4 Select Turn the <5> dial to select an image to be copied, then press <0>. X The [X] icon will appear on the upper left of the screen. If you press the button and turn the <6> dial counterclockwise, you can select an image from a threeimage display. To return to the singleimage display, turn the <6> dial clockwise. To select other images to be copied, repeat step 4. the button.
a Copying Images [OK]. 8 Select Check the information of the source card and target card, then select [OK]. X The copying will start and the progress will be displayed. When the copying is completed, the result will be displayed. Select [OK] to return to the screen in step 2. 3 Copying All Images in a Folder or on a Card You can copy all the images in a folder or on a card at once. Under [x1: Image copy], when you select [Sel.n] or [All image], you can copy all the images in the folder or on a card.
a Copying Images The file name of the copied image will be the same as the source image’s file name. If [Sel.Image] is set, you cannot copy images in multiple folders at once. Select images in each folder to copy them folder by folder. If an image is being copied to a target folder/card which has an image with the same file number, the following will be displayed: [Skip image and continue] [Replace existing image] [Cancel copy]. Select the copying method, then press <0>.
L Erasing Images You can either select and erase unnecessary images one by one or erase them in one batch. Protected images (p.334) will not be erased. Once an image is erased, it cannot be recovered. Make sure you no longer need the image before erasing it. To prevent important images from being erased accidentally, protect them. Erasing a RAW+JPEG image will erase both the RAW and JPEG images. Erasing a Single Image 1 Play back the image to be erased. the button.
L Erasing Images 3 Checkmarking [X] Images to Be Erased in a Batch By appending checkmarks to the images to be erased, you can erase multiple images at once. 1 Select [Erase images]. Under the [31] tab, select [Erase images], then press <0>. [Select and erase images]. 2 Select X An image will be displayed. If you press the button and turn the <6> dial counterclockwise, you can select an image from a threeimage display. To return to the singleimage display, turn the <6> dial clockwise.
L Erasing Images 3 Erasing All Images in a Folder or on a Card You can erase all the images in a folder or on a card at once. When [31: Erase images] is set to [All images in folder] or [All images on card], all the images in the folder or on the card will be erased. To erase all images, including protected images, format the card (p.67). The images on the card selected for [Record/play] or [Playback] under [51: Record func+card/folder sel.] will be erased.
Changing Image Playback Settings 3 Adjusting the LCD Monitor Brightness The LCD monitor’s brightness is adjusted automatically for optimum viewing depending on the ambient light level. You can also set the automatic adjustment’s brightness level (brighter or darker), or adjust the brightness manually. 1 Select [LCD brightness]. Under the [52] tab, select [LCD brightness], then press <0>. [Auto] or [Manual]. 2 Select Turn the <6> dial to make the selection. the brightness.
Changing Image Playback Settings 3 Auto Rotation of Vertical Images Vertical images are rotated automatically so they are displayed vertically on the camera’s LCD monitor and on the computer instead of horizontally. You can change the setting for this feature. 1 Select [Auto rotate]. Under the [51] tab, select [Auto rotate], then press <0>. the auto rotation. 2 SetSelect the desired setting, then press <0>.
10 Post-Processing Images You can process RAW images and resize or crop JPEG images. A M icon at the upper right of a page title indicates a function that can be used only in the following modes: . The camera may not be able to process images taken with another camera. Post-processing images as described in this chapter cannot be performed while the camera is connected to a computer via an interface cable.
R Processing RAW Images with the CameraN You can process 1 images with the camera and save them as JPEG images. As the RAW image itself does not change, you can apply different processing conditions to create any number of JPEG images from it. Note that 41 and 61 images cannot be processed with the camera. Use Digital Photo Professional (EOS software, p.520) to process those images. 1 Select [RAW image processing]. Under the [31] tab, select [RAW image processing], then press <0>.
R Processing RAW Images with the CameraN Displaying the setting screen Press <0> to display the setting screen. Turn the <5> or <6> dial to change the setting. Press <0> to finalize the setting and return to the previous screen. the image. 4 Save Select [W] (Save), then press <0>. Select [OK] to save the image. Check the destination folder and image file number, then select [OK]. To process another image, repeat steps 2 to 4. Magnified View You can magnify the image by pressing the button in step 3.
R Processing RAW Images with the CameraN RAW Image Processing Options Brightness adjustment You can adjust the image brightness up to ±1 stop in 1/3-stop increments. The displayed image will reflect the setting’s effect. White balance (p.174) You can select the white balance. If you select [Q] and press the button, you can select [Auto: Ambience priority] or [Auto: White priority]. If you select [P] and press the button, you can set the color temperature.
R Processing RAW Images with the CameraN Color space (p.193) You can select either sRGB or Adobe RGB. Since the camera’s LCD monitor is not compatible with Adobe RGB, the image will not look very different when either color space is set. Peripheral illumination correction (p.188) If [Enable] is set, the corrected image will be displayed. If the effect is difficult to discern, magnify the image (p.365) and check the four corners.
R Processing RAW Images with the CameraN Peripheral Illumination Correction, Distortion Correction, and Chromatic Aberration Correction To execute peripheral illumination correction, distortion correction, and chromatic aberration correction, the correction data of the lens used is necessary. If you cannot apply correction when processing RAW images in the camera, use EOS Utility (EOS software, p.520) to register the correction data to the camera.
S Resizing JPEG Images You can resize a JPEG image to make the pixel count lower and save it as a new image. Resizing an image is possible only with JPEG 3/K/ 5/a/b images. JPEG c and RAW images cannot be resized. 1 Select [Resize]. Under the [32] tab, select [Resize], then press <0>. X An image will be displayed. an image. 2 Select Turn the <5> dial to select the image you want to resize. If you press the button and turn the <6> dial counterclockwise, you can select an image from the index display.
S Resizing JPEG Images Resize Options by Original Image Size Original Image Size 3 K 5 a b K k Available Resize Settings 5 a b k k k k k k k k k c k k k k k Image Sizes Sizes for resized images are shown below. (Approx.) Image Quality K 5 a b c Image Quality K 5 a b c Full-frame (3:2) 7680x5120 (39.3 megapixels) 5760x3840 (22.1 megapixels) 4320x2880 (12.4 megapixels) 1920x1280 (2.5 megapixels) 720x480 (350,000 pixels) 1.3x (crop) 6016x4000* (24.1 megapixels) 4512x3008 (13.6 megapixels) 3376x2256* (7.
N Cropping JPEG Images You can crop a JPEG image and save it as another image. You can crop 3, K, 5, a and b JPEG images. JPEG c and RAW images cannot be cropped. 1 Select [Cropping]. Under the [x2] tab, select [Cropping], then press <0>. X An image is displayed. an image. 2 Select Turn the <5> dial to select the image you want to crop. If you press the button and turn the <6> dial counterclockwise, you can select an image from the index display.
N Cropping JPEG Images Moving the Cropping Frame Use <9> to move the frame over the image vertically or horizontally. Move the cropping frame until it covers the desired image area. Switching the Cropping Frame Orientation Pressing the button will toggle the cropping frame between the vertical and horizontal orientations. This enables you to create a vertically oriented image from a horizontal image. the image area to be 4 Check cropped. Press the button.
11 Sensor Cleaning The camera has a Self Cleaning Sensor Unit to automatically shake off dust adhered to the image sensor’s front layer (low pass filter). The Dust Delete Data can also be appended to the image so that the dust spots remaining can be deleted automatically by Digital Photo Professional (EOS software, p.520).
f Automatic Sensor Cleaning Whenever you set the power switch to <1> or <2>, the Self Cleaning Sensor Unit operates to automatically shake off the dust on the front of the sensor. Normally, you need not pay attention to this operation. However, you can choose to perform sensor cleaning manually, or disable it. Cleaning the Sensor Now 1 Select [Sensor cleaning]. Under the [53] tab, select [Sensor cleaning], then press <0>. [Clean nowf]. 2 Select Select [Clean nowf], then press <0>. Select [OK].
3 Appending Dust Delete DataN Normally, the Self Cleaning Sensor Unit will eliminate most of the dust that may be visible on captured images. However, in case visible dust still remains, you can append the Dust Delete Data to the image for erasing the dust spots later. The Dust Delete Data is used by Digital Photo Professional (EOS software, p.520) to erase the dust spots automatically. Preparation Prepare a solid white object such as a sheet of paper. Set the lens focal length to 50 mm or longer.
3 Appending Dust Delete DataN a solid-white object. 3 Shoot At a distance of 20 cm - 30 cm (0.7 ft. - 1.0 ft.), fill the viewfinder with a patternless, solid-white object and take a picture. X The picture will be taken in aperturepriority AE mode at an aperture of f/22. Since the image will not be saved, the data can still be obtained even if there is no card in the camera. X When the picture is taken, the camera will start collecting the Dust Delete Data.
3 Manual Sensor CleaningN Dust that could not be removed by the automatic sensor cleaning can be removed manually with a commercially-available blower, etc. Before cleaning the sensor, detach the lens from the camera. The image sensor is extremely delicate. If the sensor needs to be cleaned directly, having it done by a Canon Service Center is recommended. 1 Select [Sensor cleaning]. Under the [53] tab, select [Sensor cleaning], then press <0>. 2 Select [Clean manually]. [OK].
3 Manual Sensor CleaningN While cleaning the sensor, never do any of the following. If the power is cut off, the shutter will close and the shutter curtains and image sensor may get damaged. • Setting the power switch to <2>. • Removing or inserting the battery. The surface of the image sensor is extremely delicate. Clean the sensor with care. Use a plain blower without any brush attached. A brush can scratch the sensor. Do not insert the blower tip inside the camera beyond the lens mount.
12 Printing Images and Transferring Images to a Computer Printing (p.382) You can connect the camera directly to a printer and print out the images on the card. The camera is compliant with “wPictBridge”, which is the standard for direct printing. Digital Print Order Format (DPOF) (p.389) DPOF (Digital Print Order Format) enables you to print images recorded on the card according to your printing instructions such as the image selection, quantity to print, etc.
Preparing to Print The direct printing procedure can be performed entirely with the camera while you look at the camera’s LCD monitor. Connecting the Camera to a Printer the camera’s power switch to 1 Set <2>. the printer. 2 SetForupdetails, refer to the printer’s instruction manual. the camera to a printer. 3 Connect Use the interface cable provided with the camera. When connecting the cable to the camera, use the cable protector (p.36).
Preparing to Print back the image. 6 PlayPress the button. X The image will appear with the icon on the upper left of the screen to indicate that the camera is connected to a printer. Make sure the printer has a PictBridge connection port. Use the provided interface cable or one from Canon (p.454). When connecting the interface cable, use the provided cable protector (p.36). Movies cannot be printed. The camera cannot be used with printers conforming only to CP Direct or Bubble Jet Direct.
w Printing The screen display and setting options will differ depending on the printer. Some settings may not be available. For details, refer to the printer’s instruction manual. Printer-connected icon 1 Select the image to be printed. Check that the icon is displayed on the upper left of the LCD monitor. Turn the <5> dial to select the image to be printed. <0>. 2 Press X The print setting screen will appear. Print setting screen Sets printing effects (p.384).
w Printing Q Setting the Paper Size Select the size of the paper loaded in the printer, then press <0>. X The paper type screen will appear. Y Setting the Paper Type Select the type of the paper loaded in the printer, then press <0>. X The page layout screen will appear. U Setting the Page Layout Select the page layout, then press <0>. X The print setting screen will reappear. Borderless Prints with no borders. If your printer cannot print borderless prints, the print will have borders.
w Printing effects. 4 SetSetthethemprinting if necessary. If you do not need to set any printing effects, go to step 5. Contents displayed on the screen differ depending on the printer. Select the setting, then press <0>. Select the desired printing effect, then press <0>. If the icons are displayed brightly, you can also adjust the printing effects (p.386). Printing Effect Description EOff No automatic correction is applied. EOn Print with the printer’s standard colors.
w Printing the date and file number 5 Set imprinting. Set them if necessary. Select , then press <0>. Set the print settings as desired, then press <0>. of copies. 6 SetSettheit ifnumber necessary. Select , then press <0>. Select the number of copies, then press <0>. printing. 7 StartSelect [Print], then press <0>. The [Default] setting for printing effects and other options are the printer’s own default settings as set by the printer’s manufacturer.
w Printing e Adjusting Printing Effects In step 4 on page 384, select the printing effect. When the icons are displayed brightly, you can press the button. You can then adjust the printing effects. What can be adjusted or what is displayed will depend on the selection made in step 4. Brightness The image brightness can be adjusted. Adjust levels When you select [Manual], you can change the histogram’s distribution and adjust the image’s brightness and contrast.
w Printing Cropping the Image Tilt correction You can crop the image and print only an enlarged version of the cropped portion, as if the image is recomposed. Set the cropping right before printing. If you change the print settings after setting the cropping, you may have to set the cropping again before printing. 1 On the print setting screen, select [Cropping]. 2 Set the cropping frame size, position, and aspect ratio. The image area within the cropping frame will be printed.
w Printing Depending on the printer, you may not be able to print an image with a large image size. In such a case, resize the image (p.369), then print. If the image’s aspect ratio is different from the printing paper’s aspect ratio, the image may be cropped significantly when you print it as a borderless print. If the image is cropped, the print may look grainier due to the fewer number of pixels.
W Digital Print Order Format (DPOF) You can set the print settings such as print type, date imprinting, file number imprinting, etc. The print settings will be applied to all printordered images. (They cannot be set individually for each image.) Setting the Printing Options 1 Select [Print order]. Under the [31] tab, select [Print order], then press <0>. 2 Select [Set up]. as desired. 3 SetSetthetheoptions [Print type], [Date], and [File No.]. Select the option to be set, then press <0>.
W Digital Print Order Format (DPOF) Print type Date File number K Standard Prints one image on one sheet. L Index Multiple thumbnail images are printed on one sheet. K L Both Prints both the standard and index prints. On Off On Off [On] imprints the recorded date on the print. [On] imprints the file number on the print. 4 Exit the setting. Press the button. X The print order screen will reappear. Next, select [Sel.Image], [Byn], or [All image] to order the images to be printed.
W Digital Print Order Format (DPOF) Print Ordering Sel.Image Select and order images one by one. If you press the button and turn the <6> dial counterclockwise, you can select an image from a three-image display. To return to the single-image display, turn the <6> dial clockwise. Press the button to save the print order to the card. Standard / Both Quantity Total images selected Press <0>, and a print order for one copy of the displayed image will be placed.
W Direct Printing of Print-Ordered Images With a PictBridge printer, you can easily print images with DPOF. 1 Prepare to print. See page 380. Follow the “Connecting the Camera to a Printer” procedure up to step 5. 2 Under the [31] tab, select [Print order]. 3 Select [Print]. [Print] will be displayed only if the camera is connected to a printer and printing is possible. 4 Set the [Paper settings] (p.382). Set the printing effects (p.384) if necessary. 5 Select [OK].
d Transferring Images to a Computer You can connect the camera to a computer and operate the camera to transfer images on the card to the computer. This is called direct image transfer. The direct image transfer can be performed with the camera while you look at the LCD monitor. The images transferred to the computer will be saved in the [Pictures] or [My Pictures] folder and organized in folders by shooting date.
d Transferring Images to a Computer the camera’s power switch to 3 Set <1>. When the computer displays a screen to select the program, select [EOS Utility]. X The EOS Utility screen will appear on the computer. After the EOS Utility screen appears, do not operate EOS Utility. If any screen other than EOS Utility’s main window is displayed, [Direct transfer] in step 5 on page 396 will not be displayed. (The image transfer function will not be available.
d Transferring Images to a Computer 3 Selecting the Images to be Transferred Sel.Image 1 Select [Image transfer]. Under the [32] tab, select [Image transfer], then press <0>. 2 Select [Image sel./transfer]. 3 Select [Sel.Image]. the images to be 4 Select transferred. Turn the <5> dial to select the image to be transferred, then press <0>. Turn the <5> dial to display the [X] on the screen’s upper left, then press <0>.
d Transferring Images to a Computer the image. 5 Transfer On the computer screen, check that EOS Utility’s main window is displayed. Select [Direct transfer], then press <0>. On the confirmation dialog, select [OK], and the images will be transferred to the computer. Images selected with [Sel.n] and [All image] can also be transferred in this way. Sel.n Select [Sel.n] and select [Folder images not transfer’d].
p Specifying Images for a Photobook You can specify up to 998 images to be printed in a photobook. When you use EOS Utility (EOS software) to transfer images to a computer, the specified images will be copied to a dedicated folder. This function is useful for ordering photobooks online. Specifying One Image at a Time 1 Select [Photobook Set-up]. Under the [x1] tab, select [Photobook set-up], then press <0>. 2 Select [Select images]. the image to be specified.
p Specifying Images for a Photobook Specifying All Images in a Folder or on a Card You can specify all the images in a folder or on a card at once. When [x1: Photobook Set-up] is set to [All images in folder] or [All images on card], all the images in the folder or on the card will be specified. To clear your selections, select [Clear all in folder] or [Clear all on card]. RAW images and movies cannot be specified.
13 Customizing the Camera You can customize various camera functions to suit your picture-taking preferences with Custom Functions. Also, current camera settings can be saved under positions of the Mode Dial. The features explained in this chapter can be set and used in the following shooting modes: .
3 Custom FunctionsN 81: Exposure Exposure level increments ISO speed setting increments Bracketing auto cancel Bracketing sequence A LV Shooting p.402 p.403 k Movie Shooting k k k In a k k Number of bracketed shots p.404 k Safety shift p.405 k Same exposure for new aperture p.406 k (Still photo, with WB bracketing) 82: Exposure Set shutter speed range Set aperture range p.408 k k k k The shaded Custom Functions do not function during Live View (LV) shooting or movie shooting.
3 Custom FunctionsN 83: Others Warnings z in viewfinder Dial direction during Tv/Av Multi function lock Custom Controls Add cropping information Default Erase option Retract lens on power off A LV Shooting k Movie Shooting k k k k p.409 p.410 p.411 p.412 Depends on setting k (During playback) k k 84: Clear Selecting [84: Clear all Custom Func. (C.Fn)] will clear all the Custom Function settings. Even if [84: Clear all Custom Func.(C.
3 Custom Function SettingsN Under the [8] tab, you can customize various camera features to suit your picture-taking preferences. Any settings different from the default will be displayed in blue. C.Fn1: Exposure Exposure level increments 1/3:1/3-stop 1/2:1/2-stop Sets 1/2-stop increments for the shutter speed, aperture, exposure compensation, AEB, flash exposure compensation, etc. This is effective when you prefer to control the exposure in less fine increments than 1/3-stop.
3 Custom Function SettingsN Bracketing auto cancel ON: Enable When you set the power switch to <2>, the AEB and white balance bracketing settings will be canceled. AEB will also be canceled when the flash is ready to fire or if you switch to movie shooting. OFF: Disable The AEB and white balance bracketing settings will not be canceled even if you set the power switch to <2>.
3 Custom Function SettingsN Number of bracketed shots The number of shots taken with AEB and white balance bracketing can be changed from the default, 3 shots, to 2, 5, or 7 shots. When [Bracketing sequence: 0, -, +] is set, the bracketed shots will be taken as shown in the table below.
3 Custom Function SettingsN Safety shift OFF: Disable Tv/Av: Shutter speed/Aperture This takes effect in the shutter-priority AE (s) and aperturepriority AE (f) modes. If the subject brightness changes and the standard exposure cannot be obtained within the autoexposure range, the camera will automatically change the manually-selected setting to obtain a standard exposure. ISO: ISO speed This works in the Program AE (d), shutter-priority AE (s), and aperture-priority AE (f) modes.
3 Custom Function SettingsN Same exposure for new aperture If the mode (manual exposure shooting) is set and the ISO speed is set manually (other than Auto ISO or H (12800) is set), the maximum aperture’s f/number may change to a higher number (smaller aperture) if you do any of the following: 1. Change the lens, 2. Attach or detach an Extender, or 3. Use a zoom lens whose maximum aperture f/number changes.
3 Custom Function SettingsN This function does not work with macro lenses whose actual aperture f/number changes when the magnification changes. This function does not work with movies. If [ISO speed] is set and the exposure cannot be maintained within the range set with [ISO speed range], the ISO speed will be automatically switched within the specified range.
3 Custom Function SettingsN C.Fn2: Exposure Set shutter speed range You can set the shutter speed range. In the modes, you can set the shutter speed manually within the shutter speed range that you have set. In the modes, the shutter speed will be set automatically within the shutter speed range that you have set. Highest speed You can set it from 1/8000 sec. to 15 sec. Lowest speed You can set it from 30 sec. to 1/4000 sec. Set aperture range You can set the aperture range.
3 Custom Function SettingsN C.Fn3: Others Warnings z in viewfinder When any of the following functions are set, the icon can be displayed in the viewfinder (p.31). Select the function for which you want the warning icon to appear, and press <0> to append a . Then select [OK] to register the setting. When monochrome V is set If the Picture Style is set to [Monochrome] (p.166), the warning icon will appear. When WB is corrected If white balance correction is set (p.179), the warning icon will appear.
3 Custom Function SettingsN Dial direction during Tv/Av : Normal : Reverse direction Dial turning direction when setting the shutter speed and aperture can be reversed. In the shooting mode, the turning direction of the <6> and <5> dials will be reversed. In other shooting modes, the turning direction of only the <6> dial will be reversed. The <5> dial’s turning direction in the mode and the turning direction to set the exposure compensation in the , , and mode will be the same.
3 Custom Function SettingsN Custom Controls You can assign often-used functions to camera buttons or dials according to your preferences. For details, see page 413. Add cropping information If you set cropping information, vertical lines for the aspect ratio you have set will appear on the Live View image. You can then compose the shot as if you were shooting with a medium- or large-format camera (6x6 cm, 4x5 inch, etc.).
3 Custom Function SettingsN Default Erase option During image playback and image review after image capture, when you press the button, the erase menu appears (p.358). You can set which option, [Cancel] or [Erase], is to be preselected on this screen. If [Erase] is set, you can just press <0> to quickly erase the image. : [Cancel] selected L : [Erase] selected If [Erase] is set, be careful not to erase an image accidentally.
83: Custom ControlsN You can assign often-used functions to camera buttons or dials according to your preferences. 1 Select [83: Custom Controls]. Under the [83] tab, select [Custom Controls], then press <0>. X The Custom Controls screen to select control buttons and dials will appear. a camera button or dial. 2 Select Select a camera button or dial, then press <0>. X The name of the camera control and the assignable functions will be displayed. a function. 3 Assign Select a function, then press <0>.
83: Custom ControlsN Assignable Functions to Camera Controls Function Page k*1 k*1 419 k k 420 k k k k k k k k k k Metering and AF start 418 AF stop k AF Switch to registered AF function ONE SHOT z AI SERVO Switch to registered AF point AF point direct selection 421 Direct AF point selection: Vertical Pause Movie Servo AF Metering start 421 AE lock k AE lock (while button pressed) Exposure AE lock (hold) AE lock, AF stop 422 FE lock Set ISO speed (hold button, turn Set ISO sp
83: Custom ControlsN k k k k*2 k*2 k k k*3 k*3 k k*4 k k k k k k k k k k k k k k k k k k < > stands for “AF stop button” provided on super telephoto lenses equipped with Image Stabilizer.
83: Custom ControlsN Images Assignable Functions to Camera Controls Function Page Switch between crop/aspect 423 One-touch image quality setting One-touch image quality (hold) 424 Image quality Picture Style 425 Depth-of-field preview IS start Menu display 425 Operation Register/recall shooting function k*7 k*7 k k Image playback Magnify/Reduce (press SET, turn ) Cycle: y • g/Drive • AF/WB • q 426 Unlock while button pressed Flash function settings No function (disabled) 416
83: Custom ControlsN k*5 k*6 k*6 k* k*6 6 k k k k k k k k k k k k k k k k < > stands for “AF stop button” provided on super telephoto lenses equipped with Image Stabilizer.
83: Custom ControlsN : Metering and AF start When you press the button assigned to this function, metering and AF are executed. *1:When assigned to the
or button, pressing the button while the setting screen is displayed will enable you to set the detailed AF settings. When shooting, pressing the or button will execute AF as it was set. AF start position When [Registered AF point] is set, you can press the or button to switch to the registered AF point.
83: Custom ControlsN AI Servo AF characteristics (p.109) Press the
or button to perform AF with the set case from [Case1] to [Case6]. AF operation (p.86) Press the or button to perform AF with the set AF operation. AF area selection mode (p.90) Press the or button to perform AF with the set AF area selection mode. If you want to keep using currently selected AF point when you press the or button, set [AF start position] to [Manually selected AF point].
83: Custom ControlsN : Switch to registered AF function After setting and assigning this function to a button, you can apply the following settings by holding down the assigned button for AF: AF area selection mode (p.90), Tracking sensitivity (p.114), Acceleration/ deceleration tracking (p.115), AF point auto switching (p.116), Servo 1st image priority (p.118), and Servo 2nd image priority (p.119). Convenient when you want to change the AF characteristics during AI Servo AF.
83: Custom ControlsN : Direct AF point selection During metering, you can select an AF point directly with the <9> dial or <5> without pressing the button. With the <5> dial, you can select a left or right AF point. (Looping sequence for Zone AF.) *5:On the Multi-controller setting screen, when you press the button, you can press the center of <9> to select [Switch to center AF point] or [Switch to registered AF point]. To register the AF point, see page 418.
83: Custom ControlsN : AE lock (while button pressed) The exposure will be locked (AE lock) while you press the shutter button. : AE lock (hold) When you press the button assigned to this function, you can lock the exposure (AE lock). The AE lock will be maintained until you press the button again. Convenient when you want to focus and meter the shot at different areas or when you want to take multiple shots at the same exposure setting.
83: Custom ControlsN : Exposure compensation (hold button, turn ) You can set the exposure compensation by holding down <0> and turning the <6> dial. Convenient when you want to set exposure compensation while manual exposure and Auto ISO are set. : Shutter speed setting in M mode In manual exposure , you can set the shutter speed with the <6> or <5> dial. : Aperture setting in M mode In manual exposure , you can set the aperture with the <5> or <6> dial.
83: Custom ControlsN : One-touch image quality setting Pressing the button assigned to this function will switch to the imagerecording quality set here. While this change is in effect, the imagerecording quality (JPEG/RAW) will blink in the viewfinder (with [Show/ hide in viewfinder]’s [Image quality] checkmarked). After the shooting ends, the One-touch image quality setting will be canceled and the image-recording quality will be switched back to the previous quality.
83: Custom ControlsN : Picture Style Press <0> to display the Picture Style selection setting screen on the LCD monitor (p.164). : Depth-of-field preview When you press the depth-of-field preview button, the aperture will stop down and you can check the depth of field (p.209). : IS start If you press the button assigned to this function when the lens’s IS switch is set to <1>, lens’s Image Stabilizer will operate (p.55). : Menu display Press <0> to display the menu on the LCD monitor.
83: Custom ControlsN : Image playback Pressing <0> will play back images. : Magnify/Reduce (press SET, turn ) Press <0> to magnify or reduce the images recorded on the card. See page 330 for the operation procedure. During Live View or movie shooting (except u+Tracking), you can also magnify the image (p.274, 275). : Cycle: y • g/Drive • AF/WB • q Pressing the button changes the settable function in this sequence: y•g9R•f9B•q.
Custom Quick Control On the standard Quick Control screen (p.60), pre-determined shooting functions are displayed in the default layout. On the Custom Quick Control screen, you can customize the screen with your preferred shooting functions and layout. This feature is called “Custom Quick Control”. This page explains how to change the layout of the Custom Quick Control screen. Page 61 explains how to use the Quick Control screen, and page 442 explains how to display the Custom Quick Control screen.
Custom Quick Control an item. 4 AddPress the button. Turn the <5> dial or use <9> to select the item to be added, then press <0>. To remove an item, select the item, then press the button. Otherwise, select [Clear all items] in step 2. For items that let you select the icon size, turn the <5> dial or use <9> to select the size, then press <0>. For items which can be positioned and for display sizes, see page 430. the item.
Custom Quick Control Sample layout Repeat steps 4 and 5 to position other items as desired. To delete an item already in position, select it and press the button. the setting. 6 ExitPress the button to exit the setting. The screen in step 2 will reappear. Sample screen the setting screen. 7 Check Under [53: z button display options], check that [Custom Quick Control screen] is checkmarked (p.442). Press the button to display the Custom Quick Control screen (p.442) and check the layout.
Custom Quick Control Available Items and Display Sizes for the Screen Layout (Vertical x horizontal cells) Item and Size 1x1 1x2 1x3 Shooting mode k Shutter speed k k Aperture k k ISO speed k k Exposure compensation/ AEB setting k k k Flash exposure compensation k k k Picture Style k White balance k k White balance shift/ bracketing k k Auto Lighting Optimizer k Custom Controls k AF operation k AF point selection k Metering mode k Drive mode k Recording function
Custom Quick Control Mode Settings and Display Conditions You can also set Custom Quick Control and display the Custom Quick Control screen in the mode. However, functions such as [Expo.comp./AEB] that are not displayed on the menu screen for mode will not appear on the Custom Quick Control screen. Also, [ISO speed] and other functions that cannot be set with the Quick Control screen in the mode will be grayed out.
3 Registering My MenuN Under My Menu tab, you can register menu items and Custom Functions whose settings you change frequently. You can also name the registered menu tabs and press the button to display the My Menu tab first. Adding My Menu Tab 1 Select [Add My Menu tab]. Under the [9] tab, select [Add My Menu tab], then press <0>. [OK]. 2 Select X The [MY MENU1] tab is created. You can create up to five menu tabs by repeating steps 1 and 2.
3 Registering My MenuN 2 Select [Select items to register]. the desired items. 3 Register Select the desired item, then press <0>. Select [OK] on the confirmation dialog. You can register up to six items. To return to the screen in step 2, press the button. My Menu Tab Settings You can sort and delete items under the menu tab, and rename or delete the menu tab. Sort registered items You can change the order of the registered items in My Menu.
3 Registering My MenuN Delete tab You can delete the My Menu tab currently displayed. Select [Delete tab] to delete the [MY MENU*] tab. Rename tab You can rename the My Menu tab from [MY MENU*]. 1 Select [Rename tab]. text. 2 Enter Press the button to delete any unnecessary characters. Press the button. The text palette will be highlighted with a color frame, and text can be entered. Operate the <5> dial or <9> to move the and select the desired character. Then press <0> to enter it.
3 Registering My MenuN Deleting all My Menu tabs / Deleting all items You can delete all My Menu tabs and delete all My Menu items. Delete all My Menu tabs You can delete all My Menu tabs. When you select [Delete all My Menu tabs], all the tabs from [MY MENU1] to [MY MENU5] will be deleted and the [9] tab will revert to its default. Delete all items You can delete all the items registered under the [MY MENU1] to [MY MENU5] tabs and keep the tabs. The menu tab(s) will remain.
3 Registering My MenuN Menu Display Settings You can select [Menu display] to set the menu screen that is to appear first when you press the button. Normal display Displays the last displayed menu screen. Display from My Menu tab Displays with the [9] tab selected. Display only My Menu tab Only the [9] tab is displayed. (The z, 2, 3, 5, and 8 tabs will not be displayed.
w: Registering Custom Shooting ModesN You can register current camera settings, such as the shooting mode, menu functions, and Custom Function settings, as Custom shooting modes under the Mode Dial’s , , and positions. 1 Select [Custom shooting mode (C1-C3)]. Under the [54] tab, select [Custom shooting mode (C1-C3)], then press <0>. 2 Select [Register settings]. the Custom shooting 3 Register mode. Select the Custom shooting mode to be registered, then press <0>.
w: Registering Custom Shooting ModesN Settings To Be Registered Shooting functions Shooting mode, Shutter speed, Aperture, ISO speed, AF operation, AF area selection mode, AF point, Drive mode, Metering mode, Exposure compensation amount, Flash exposure compensation amount Menu functions [z1] Image quality, Image review time, Beep, Release shutter without card, Lens aberration correction, Flash firing, E-TTL II flash metering, Flash sync speed in Av mode [z2] Exposure compensation/AEB, ISO speed settings,
w: Registering Custom Shooting ModesN [23] Lens electronic MF, AF-assist beam firing, One-Shot AF release priority [24] Lens drive when AF impossible, Selectable AF point, Select AF area selection mode, AF area selection method, Orientation linked AF point, Initial AF point, AI Servo AF, Auto AF point selection: EOS iTR AF [25] Manual AF point selection pattern, AF point display during focus, VF display illumination, AF Microadjustment [x2] Slide show (settings), Image jump with 6 [x3] Highlight alert, AF
MEMO 440
14 Reference This chapter provides reference information for camera features, system accessories, etc. Certification Logo Select [54: Certification Logo Display] and press <0> to display some of the logos of the camera’s certifications. Other certification logos can be found in this Instruction Manual, on the camera body, and on the camera’s package.
B Button Functions When the camera is ready to shoot, pressing the button can switch the display as follows: Camera settings, Electronic level (p.75), Quick Control screen (p.60), and Custom Quick Control screen (p.427). Under the [53] tab, [z button display options] enables you to select the options displayed when the button is pressed. Select the desired display option and press <0> to append a checkmark [X]. After completing the selections, select [OK].
B Button Functions If you turn off the power while the Electronic level, Quick Control screen, or Custom Quick Control screen is displayed, the same screen will be displayed when you turn on the power again. To cancel this function, press the button a number of times until the screen is blank, then turn off the power switch. Note that you cannot remove the [X] for all four display options. The [Displays camera settings] sample screen is displayed in English for all languages.
B Button Functions Quick Control Screen Aperture Shutter speed Shooting mode AE lock Highlight tone priority Exposure level indicator ISO speed Exposure compensation Exposure compensation Custom Controls Auto Lighting Optimizer White balance correction Picture Style AF operation Quick Control icon Battery level White balance Metering mode Eye-Fi card transmission status GPS acquisition status Drive mode Image-recording quality Possible shots Maximum burst/Number of remaining multiple exposures Card
B Button Functions Button Functions for the Quick Control and Custom Quick Control Screens When you press the , , , or button, the setting screen appears and you can use <6>, <5>, <9>, or to set the functions.
3 Checking the Battery Information You can check the battery’s condition on the LCD monitor. Each Battery Pack LP-E6N/LP-E6 has a unique serial number, and you can register multiple batteries to the camera. When you use this feature, you can check the registered batteries’ approximate remaining capacity and operation history. Select [Battery info.]. Under the [53] tab, select [Battery info.], then press <0>. X The battery info. screen will appear.
3 Checking the Battery Information If a battery communication error message is displayed, follow the instructions in the message. Registering Batteries to the Camera You can register up to six LP-E6N/LP-E6 batteries to the camera. To register multiple batteries to the camera, follow the procedure below for each battery. 1 Press the button. With the battery info. screen displayed, press the button. X The battery history screen will appear.
3 Checking the Battery Information Labeling Serial Numbers on Batteries It is convenient to label each registered Battery Pack LP-E6N/LP-E6 with their serial numbers, using commercially-available labels. 1 Serial number Write the serial number on a label. Write the serial number displayed on the battery history screen on a label approx. 25 mm x 15 mm / 1.0 in. x 0.6 in. in size. b 2 9 fd a30 the battery and affix the 2 Remove label. Set the power switch to <2>.
3 Checking the Battery Information Checking the Remaining Capacity of a Registered Battery You can check the remaining capacity of any battery (even when not installed) and also when it was last used. Serial number Date last used Look for the serial number. Refer to the battery’s serial number label and look for the battery’s serial number on the battery history screen. X You can check the respective battery’s remaining capacity and the date when it was last used.
Using a Household Power Outlet You can power the camera with a household power outlet by using the DC Coupler DR-E6 and AC Adapter AC-E6N (both sold separately). 1 Connect the DC Coupler’s plug. Connect the DC Coupler’s plug to the AC Adapter’s socket. the power cord. 2 Connect Connect the power cord as shown in the illustration. After using the camera, unplug the power plug from the power outlet. the cord in the groove.
H Using Eye-Fi Cards With a commercially-available Eye-Fi card already set up, you can automatically transfer captured images to a computer or upload them to an online service via a wireless LAN. The image transfer is a function of the Eye-Fi card. For instructions on how to set up and use the Eye-Fi card or to troubleshoot any image transfer problems, refer to the Eye-Fi card’s instruction manual or contact the card manufacturer.
H Using Eye-Fi Cards the connection 4 Display information. Select [Connection info.], then press <0>. the [Access point SSID:]. 5 Check Check that an access point is displayed for [Access point SSID:]. You can also check the Eye-Fi card’s MAC address and firmware version. Press the button to exit the menu. the picture. 6 Take X The picture is transferred and the Transmission status H(Gray) Not connected : H(Blinking) Connecting... : H(Illuminated) Connected : H(d) Transferring...
H Using Eye-Fi Cards Cautions for Using Eye-Fi Cards If “ ” is displayed, an error occurred while retrieving the card information. Turn the camera’s power switch off and on again. Even if [Eye-Fi trans.] is set to [Disable], it may still transmit a signal. In hospitals, airports, and other places where wireless transmissions are prohibited, remove the Eye-Fi card from the camera. If the image transfer does not function, check the Eye-Fi card and computer settings.
System Map ST-E2 ST-E3-RT Dioptric Adjustment Lenses Eg 270EX II 430EX III-RT/ 600EX II-RT 430EX III Macro Ring Lite MR-14EX II Macro Twin Lite MT-24EX Bundled Accessories Eyecup Eg Anti-Fog Eyepiece Eg Cable protector Wide Strap Angle Finder C Battery Pack LP-E6N*1 Battery Charger LC-E6 or LC-E6E AC Adapter DC Coupler AC-E6N*5 DR-E6*5 Hand Strap E2 Leather Case EH20-L 454 Battery Grip BG-E11 Battery Magazine BGM-E11L for LP-E6N/LP-E6 (attached to BG-E11) Car Battery Cable CB-570 Car Batte
System Map GPS Receiver GP-E2*2 Timer Remote Remote Controller Switch TC-80N3 RS-80N3 Wireless Controller LC-5 Remote Controller RC-6 EF lenses Directional Stereo Microphone DM-E1 HDMI Cable HTC-100 (2.9 m/9.5 ft.) Wireless File Transmitter WFT-E7 (Ver. 2)/ WFT-E7*3 EOS DIGITAL Solution Disk TV/Video Wireless LAN access point Wireless LAN adapter Interface Cable IFC-150U II (1.5 m/4.9 ft.) Interface Cable IFC-500U II*4 (4.7 m/15.4 ft.
Function Availability Table According to Shooting Mode Still Photo Shooting o: Set automatically k: User selectable Function All image quality settings selectable d s f a F k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k Crop/aspect ratio ISO spe
Function Availability Table According to Shooting Mode Function A d s f a F o k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k*3 k k k k k k k k k k High-speed continuous shooting k k k k k k k k k k k k k k k k k k Low-speed continuous shooting k k k k k k Silent single shooting 10-sec. self-timer/Remote control k k k k k k k k k k k k k k k k k k 2-sec.
Function Availability Table According to Shooting Mode Movie Shooting o: Set automatically k: User selectable : Not selectable/Disabled Still Photos*1 Movies Function Picture Style k k k k k k k k k k k k Automatically set/Auto ISO o o o o k o o k k k k k k o k k k Color temperature setting k k k k k k k k k k k k k k k k k k k k Correction k k k k o k k k k o k k k k k k o k k k k k o k k k k k k k k k k k k k k k k k k k k k k k o o o o o o k k k k k k
Function Availability Table According to Shooting Mode Still Photos*1 Movies Function Metering A d/F s f a y k M y o o o o k k k k *3 k k k *4 o A o d/F/s/f a M k o o k k k *4 k k k k k k k k k k k k k k k k k k k k k k k k Program shift AE lock Exposure Exposure compensation *3 AEB Depth-of-field preview Single shooting High-speed continuous shooting Low-speed continuous shooting Drive Silent single shooting Silent continuous shooting 10-sec.
Menu Settings Viewfinder Shooting and Live View Shooting z: Shooting 1 (Red) Page 1 / 41 / 61 Image quality 73 / 83 / 7K / 8K / 75 / 85 / 7a / 8a / b / c 149 Image review time Off / 2 sec. / 4 sec. / 8 sec. / Hold 70 Beep Enable / Disable 69 Release shutter without card Enable / Disable 44 Lens aberration correction External Speedlite control Peripheral illumination: Enable / Disable Chromatic aberration: Enable / Disable Flash firing / E-TTL II metering / Flash sync.
Menu Settings z: Shooting 2 (Red) Page Exposure compensation/ 1/3- and 1/2-stop increments, ±5 stops AEB setting* (AEB ±3 stops) ISO speed settings ISO speed / ISO speed range / Auto ISO range / Minimum shutter speed Auto Lighting Optimizer Disable / Low / Standard / High White balance Disabled in M or B modes Color space 158 182 Q (Ambience priority) / Qw (White priority) / W/E/R/Y/U/D/O/P (Approx.
Menu Settings z: Shooting 4* (Red) Page Interval timer Disable / Enable (Interval / Number of shots) 239 Bulb timer Disable / Enable (Exposure time) 219 Anti-flicker shooting Disable / Enable 191 Mirror lockup Disable / Press V twice to shoot / Shoot 1/8 sec after press / Shoot 1/4 sec after press / Shoot 1/2 sec after press / Shoot 1 sec. after press / Shoot 2 sec. after press 234 Crop/aspect ratio Full-frame / 1.3x (crop) / 1.
Menu Settings 2: AF1 (Purple) Page Case 1 Versatile multi purpose setting 110 Case 2 Continue to track the subjects, ignoring possible obstacles 110 Case 3 Instantly focus on subjects suddenly entering AF points 111 Case 4 For subjects that accelerate or decelerate quickly 111 Case 5 For erratic subjects moving quickly in any direction 112 Case 6 For subjects that change speed and move erratically 113 AI Servo 1st image priority Release priority / Equal priority / Focus priority 118
Menu Settings 2: AF4 (Purple) Page Lens drive when AF impossible Continue focus search / Stop focus search 123 Selectable AF point 61 points / Only cross-type AF points / 15 points / 9 points 124 Select AF area selection mode Manual selection: Spot AF / Manual selection: 1 point AF / Expand AF area: / Expand AF area: Surround / Manual selection: Zone AF / Auto selection: 61 point AF 125 AF area selection method S 9 M-Fn button / S 9 Main Dial 126 Orientation linked AF point Same for both ver
Menu Settings 3: Playback 1 (Blue) Page Protect images Protect images 334 Rotate image Rotate images 333 Erase images Erase images 358 Print order Specify images to be printed (DPOF) 392 Photobook Set-up Specify images for a photobook 397 Image copy Copy images between cards 354 RAW image processing Process 1 images 364 3: Playback 2 (Blue) Cropping Partially crop JPEG images 371 Resize Downsize JPEG image’s pixel count 369 Rating [OFF] / l / m / n / o / p 337 Slide show Set
Menu Settings 5: Set-up 1 (Yellow) Page Recording function: Standard / Auto switch card / Record separately / Record to multiple 146 Record/playback / Playback: f / g 148 Folder: Selecting and creating a folder 194 File numbering Continuous / Auto reset / Manual reset 199 File name Preset code / User setting 1 / User setting 2 196 Auto rotate OnzD / OnD / Off 362 Format card Erase data on the card by formatting 67 Eye-Fi settings Displayed when a commercially-available EyeFi card is in
Menu Settings 5: Set-up 3 (Yellow) Page Video system For NTSC / For PAL 297 351 Battery information Power source / Remaining capacity / Shutter count / Recharge performance / Battery registration / Serial number / Battery history 446 Auto cleaning f: Enable / Disable Sensor cleaning Clean now f 374 Clean manually 377 z button display options Displays camera settings / Electronic level / Quick Control screen / Custom Quick Control screen 442 Custom Quick Control Customize the functions and
Menu Settings 5: Set-up 4 (Yellow) Page Custom shooting mode Register current camera settings to the Mode (C1-C3) Dial’s w, x, and y positions 437 Clear all camera settings Resets the camera to the default settings 70 Copyright information Display copyright information / Enter author’s name / Enter copyright details / Delete copyright information 201 Certification Logo Display Some of the camera’s certification logos are displayed 441 z firmware ver.
Menu Settings Movie Shooting z: Shooting 4*1 (Movie) (Red) Page Movie Servo AF Enable / Disable 313 AF method u+Tracking / FlexiZone - Single 315 Grid display Off / 3x3 l / 6x4 m / 3x3+diag n 315 Movie recording size • 1920x1080 / 1280x720 / 640x480 • NTSC: 59.94p / 29.97p / 23.98p PAL: 50.00p / 25.
Menu Settings z: Shooting 5*1 (Movie) (Red) Page Silent LV shooting Mode 1 / Mode 2 / Disable 315 Metering timer 4 sec. / 8 sec. / 16 sec. / 30 sec. / 1 min. / 10 min. / 30 min. 316 Time code Count up / Start time setting / Movie recording count / Movie play count*2 / Drop frame*3 303 Silent Control Enable h / Disable h 302 V button function Time-lapse movie /z / q/z / /k / q/k Disable / Enable (Interval / No.
Troubleshooting Guide If a problem occurs with the camera, first consult this Troubleshooting Guide. If this Troubleshooting Guide does not resolve the problem, contact your dealer or nearest Canon Service Center. Power-Related Problems The battery does not recharge. If the battery’s remaining capacity is 94% or higher, the battery will not be recharged (p.446). Do not use any battery other than genuine Battery Pack LP-E6N/LPE6. The charger’s lamp blinks at high speed.
Troubleshooting Guide The access lamp still lights or blinks even when the power switch is <2>. If the power is turned off while an image is being recorded to the card, the access lamp will remain on or continue to blink for a few seconds. When the image recording is completed, the power will turn off automatically. [Does this battery/do these batteries display the Canon logo?] is displayed. Do not use any battery other than a genuine Battery Pack LP-E6N/LP-E6. Remove and install the battery again (p.42).
Troubleshooting Guide Shooting-Related Problems The lens cannot be attached. The camera cannot be used with EF-S or EF-M lenses (p.52). The viewfinder is dark. Install a recharged battery in the camera (p.40). No images can be shot or recorded. Make sure the card is properly inserted (p.43). If you are using an SD card, slide the card’s write-protect switch to the Write/Erase setting (p.43). If the card is full, replace the card or delete unnecessary images to make space (p.43, 358).
Troubleshooting Guide I have to press the shutter button twice completely to take a picture. If [z4: Mirror lockup] is set to [Press V twice to shoot], set it to [Disable]. The image is out of focus or blurred. Set the lens’s focus mode switch to (p.52). Press the shutter button gently to prevent camera shake (p.54-55). If the lens has an Image Stabilizer, set the IS switch to <1>. In low light, the shutter speed may become slow. Use a faster shutter speed (p.206), set a higher ISO speed (p.
Troubleshooting Guide The AF points do not light up in red. The AF points light up in red when focus is achieved in low-light conditions. In the , , , , and modes, you can set whether to have the AF points light in red when focus is achieved (p.132). The continuous shooting speed is slow. The continuous shooting speed may become slower depending on the shutter speed, aperture, subject conditions, brightness, lens, flash use, temperature, battery type, remaining battery level, etc. (p.143).
Troubleshooting Guide I cannot shoot in the 4:3 or 16:9 aspect ratio. During viewfinder shooting, you cannot shoot in either the 4:3 or the 16:9 aspect ratio even when the aspect ratio is set. During Live View shooting, you can shoot images in the 4:3 and 16:9 aspect ratios (p.154). ISO 100 cannot be set. ISO speed expansion cannot be selected. If [z3: Highlight tone priority] is set to [Enable], the settable ISO speed range will be ISO 200 - ISO 6400.
Troubleshooting Guide Multi Shot Noise Reduction cannot be set. If the image-recording quality is set to RAW or RAW+JPEG, [Multi Shot Noise Reduction] cannot be set. The Live View image or movie shooting image is not displayed during multiple-exposure shooting. If [On:ContShtng] is set, Live View display, image review after image capture, or image playback is not possible during shooting (p.226). Live View shooting ends when multiple exposure shooting is performed.
Troubleshooting Guide The flash does not fire. Make sure the flash (or PC sync cord) is securely attached to the camera. If you use a non-Canon flash unit with Live View shooting, set [z6: Silent LV shoot.] to [Disable] (p.266). The flash always fires at full output. If you use a flash unit other than an EX-series Speedlite, the flash will always be fired at full output (p.245).
Troubleshooting Guide During Live View or movie shooting, a white icon is displayed. or red E It indicates that the camera’s internal temperature is high. If the white < > icon is displayed, the still photo’s image quality may deteriorate. If the red icon is displayed, it indicates that the Live View or movie shooting will soon stop automatically (p.277, 317). Movie shooting stops by itself. If the card’s writing speed is slow, movie shooting may stop automatically.
Troubleshooting Guide The manually set ISO speed changes when switching to movie shooting. If you shoot a movie with manual exposure set to L (equivalent to ISO 50), the ISO speed setting will switch to ISO 100. Even if you switch back to still photo shooting, the ISO speed will not revert to L. The exposure changes during movie shooting. If you change the shutter speed or aperture during movie shooting, the changes in the exposure may be recorded.
Troubleshooting Guide When I shoot still photos during movie shooting, the movie shooting stops. To shoot still photos during movie shooting, using a CF card capable of UDMA transfer or a UHS-I SD card is recommended. Setting a lower image quality for still photos or shooting fewer continuous still photos may resolve the problem. Time code is off. Shooting still photos during movie shooting will cause a discrepancy between the actual time and time code.
Troubleshooting Guide Display Problems The menu screen shows fewer tabs and options. In the mode, only certain menu tabs and options are displayed. Set the shooting mode to , , , or (p.64). Under the [9] tab, [Menu display] is set to [Display only My Menu tab] (p.436). The file name’s first character is an underscore (“_”). Set the color space to sRGB. If Adobe RGB is set, the first character will be an underscore (p.193). The fourth character in the file name changes.
Troubleshooting Guide The date and time are not in the picture. The shooting date and time do not appear in the picture. The date and time are recorded in the image data as shooting information. When printing, you can imprint the date and time in the picture, using the date and time recorded in the shooting information (p.385, 389). [###] is displayed. If the number of images recorded on the card exceeds the number the camera can display, [###] will be displayed (p.339).
Troubleshooting Guide Playback Problems Part of the image blinks in black. [33: Highlight alert] is set to [Enable] (p.325). A red box is displayed on the image. [33: AF point disp.] is set to [Enable] (p.325). The image cannot be erased. If the image is protected, it cannot be erased (p.334). The movie cannot be played back. Movies edited with a computer cannot be played back with the camera. Camera operation noise can be heard when the movie is played back.
Troubleshooting Guide No picture on the TV set. Check if the [53: Video system] is correctly set to [For NTSC] or [For PAL] (depending on the video system of your TV set). Check that the HDMI cable’s plug is inserted all the way in (p.351). There are multiple movie files for a single movie shoot. If the movie file size reaches 4 GB, another movie file will be created automatically (p.299). My card reader does not recognize the card.
Troubleshooting Guide Sensor Cleaning Problems The shutter makes a noise during sensor cleaning. If you selected [Clean nowf], the shutter will make a noise, but no picture is taken (p.374). Automatic sensor cleaning does not work. If you repeatedly turn the power switch <1> / <2> at a short interval, the icon may not be displayed (p.47). Printing-Related Problems There are fewer printing effects than listed in the instruction manual. Contents displayed on the screen vary depending on the printer.
Error Codes If there is a problem with the camera, an error message will appear. Follow the onscreen instructions. Error number Cause and countermeasures Number 01 02 Error Message and Solution Communications between the camera and lens is faulty. Clean the lens contacts. Î Clean the electrical contacts on the camera and lens, use a Canon lens, or remove and install the battery again (p.25, 26, 42). Card* cannot be accessed. Reinsert/change card* or format card* with camera.
Specifications • Type Type: Recording media: Image sensor size: Compatible lenses: Lens mount: Digital, single-lens reflex, AF/AE camera CF cards (Type I, UDMA 7 supported) SD/SDHC*/SDXC* memory cards * UHS-I cards compatible. Approx. 36.0 x 24.0 mm Canon EF lenses * Excluding EF-S and EF-M lenses (35mm-equivalent lens focal length is as indicated on the lens) Canon EF mount • Image Sensor Type: Effective pixels: Aspect ratio: Dust delete feature: CMOS sensor Approx. 50.
Specifications Recording function: Create/select a folder: File name: File numbering: Standard, Auto switch card, Record separately, Record to multiple Possible Preset code / User setting 1 / User setting 2 Continuous, Auto reset, Manual reset • Image Processing During Shooting Picture Style: White balance: Noise reduction: Automatic image brightness correction: Highlight tone priority: Lens aberration correction: Auto, Standard, Portrait, Landscape, Fine Detail, Neutral, Faithful, Monochrome, User Def
Specifications • Autofocus Type: TTL secondary image-registration, phase-difference detection with the dedicated AF sensor AF points: 61 (Cross-type AF point: Max. 41 points) * Number of available AF points, cross-type points, and Dual cross-type points vary depending on the lens. * Dual cross-type focusing at f/2.8 with 5 AF points vertically aligned at the center. (AF group: When Group A lenses are used) Focusing brightness EV -2 - 18 (Conditions: f/2.
Specifications Exposure control: ISO speed (Recommended exposure index): ISO speed settings: Exposure compensation: AE lock: Anti-flicker: Interval timer: Bulb timer: Program AE (Scene Intelligent Auto, Program), Shutterpriority AE, Aperture-priority AE, Manual exposure, Bulb exposure Scene Intelligent Auto: ISO 100 - ISO 3200 set automatically P, Tv, Av, M, B: Auto ISO, ISO 100 - ISO 6400 (in 1/3- or whole-stop increments), or ISO expansion to L (equivalent to ISO 50) or H (equivalent to ISO 12800) IS
Specifications Continuous shooting speed: Max. burst (With full-frame): High-speed continuous shooting: Max. approx. 5.0 shots/sec. Low-speed continuous shooting: Max. approx. 3.0 shots/sec. Silent continuous shooting: Max. approx. 3.0 shots/sec. JPEG Large/Fine: Approx. 31 shots (approx. 510 shots) RAW: Approx. 12 shots (approx. 14 shots) RAW+JPEG Large/Fine: Approx. 12 shots (approx. 12 shots) * Figures are based on Canon’s testing standards (ISO 100 and Standard Picture Style) and an 8 GB CF card.
Specifications • Movie Shooting Recording format: Movie: Audio: Recording size and frame rate: Compression method: File size: Card requirements (Writing/reading speed): Focus method: Movie servo AF: Focusing brightness range: Metering mode: Brightness metering range: Exposure control: Exposure compensation: ISO speed (Recommended exposure index): Time code: Drop frames: MOV MPEG-4 AVC / H.264 Variable (average) bit rate Linear PCM Full HD (1920x1080): 29.97p/25.00p/23.98p HD (1280x720) : 59.94p/50.
Specifications Sound recording: Grid display: Time-lapse movie: Still photo shooting: Built-in monaural microphone, external stereo microphone terminal provided Sound-recording level adjustable, wind filter provided, attenuator provided 3 types Shooting interval and number of shots settable Required shooting time period, playback length, and remaining card capacity viewable Possible • LCD Monitor Type: Monitor size and dots: Brightness adjustment: Electronic level: Interface languages: Help display: T
Specifications • Post-Processing of Images In-camera RAW image processing: Resize: Cropping: Brightness correction, White balance, Picture Style, Auto Lighting Optimizer, High ISO speed noise reduction, JPEG image-recording quality, Color space, Peripheral illumination correction, Distortion correction, Chromatic aberration correction Provided Provided • Direct Printing Compatible printers: Printable images: Print ordering: PictBridge-compatible printers JPEG and RAW images DPOF Version 1.
Specifications • Power Battery: Battery information: Number of possible shots: Movie shooting time: Battery Pack LP-E6N/LP-E6, quantity 1 * AC power usable with household power outlet accessories. * With Battery Grip BG-E11 attached, AA/R6 batteries can be used. Remaining capacity, Shutter count, Recharge performance, and Battery registration possible With viewfinder shooting: Approx. 700 shots at room temperature (23°C/73°F), approx.
Specifications All the specifications listed above are common between EOS 5DS and EOS 5DS R. All the data above is based on Canon’s testing standards and CIPA (Camera & Imaging Products Association) testing standards and guidelines. Dimensions and weight listed above are based on CIPA Guidelines (except weight for camera body only). Product specifications and the exterior are subject to change without notice.
Trademarks Adobe is a trademark of Adobe Systems Incorporated. Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. Macintosh and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries. CompactFlash is a trademark of SanDisk Corporation. SDXC logo is a trademark of SD-3C, LLC. HDMI, HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Use of Genuine Canon Accessories Is Recommended This product is designed to achieve excellent performance when used with genuine Canon accessories. Canon shall not be liable for any damage to this product and/or accidents such as fire, etc., caused by the malfunction of non-genuine Canon accessories (e.g., a leakage and/or explosion of a battery pack).
Digital Camera Model DS126521 / DS126611 Systems This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for class B digital devices, pursuant to Part 15 of the FCC Rules.
USA and Canada only: The Lithium ion/polymer battery that powers the product is recyclable. Please call 1-800-8-BATTERY for information on how to recycle this battery. For CA, USA only Included lithium battery contains Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate/ for details. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO LOCAL REGULATION.
MEMO 502
MEMO 503
MEMO 504
MEMO 505
MEMO 506
MEMO 507
MEMO 508
MEMO 509
MEMO 510
MEMO 511
MEMO 512
MEMO 513
MEMO 514
15 Viewing the CD-ROM Instruction Manuals / Downloading Images to Your Computer This chapter explains how to view the Camera Instruction Manual CD-ROM on your computer, download images from the camera to your computer, gives an overview of the software in the EOS DIGITAL Solution Disk (CD-ROM), and explains how to install the software on your computer. It also explains how to view the Software Instruction Manuals.
Viewing the Camera Instruction Manual CD-ROM The Camera Instruction Manual CD-ROM contains the following electronic manuals (PDF files): Camera Instruction Manual Explains all the camera functions and procedures, including basic content. Quick Reference Guide Simple and portable guide covering basic function settings, shooting instructions, and playback instructions. Viewing the Camera Instruction Manual CD-ROM To view the instruction manuals (PDF files), Adobe Reader 6.
Viewing the Camera Instruction Manual CD-ROM the START file. 3 Double-click X The screen shown in step 4 will appear. The icon displayed will differ depending on your computer’s operating system. 4 Click your language. the instruction manual you want to 5 Click read. X The instruction manual will be displayed. You can save the PDF file to your computer. To learn how to use Adobe Reader, refer to Adobe Reader’s Help section.
Downloading Images to a Computer You can use EOS software to download the images in the camera to your computer. There are two ways to do this. Downloading by Connecting the Camera to the Computer 1 Install the software (p.521). the provided interface cable 2 Use to connect the camera to your computer. Use the interface cable provided with the camera. When connecting the cable to the camera, use the cable protector (p.36).
Downloading Images to a Computer Downloading Images with a Card Reader You can use a card reader to download images to your computer. 1 Install the software (p.521). the card into the card 2 Insert reader. Digital Photo Professional to 3 Use download the images. For details, refer to the Digital Photo Professional Instruction Manual (p.522). When downloading images from the camera to your computer with a card reader without using EOS software, copy the DCIM folder on the card to your computer.
Software Overview EOS DIGITAL Solution Disk Various software for EOS DIGITAL cameras are contained on the EOS DIGITAL Solution Disk. EOS Utility With the camera connected to a computer, EOS Utility enables you to transfer still photos and movies shot with the camera to the computer. You can also use this software to set various camera settings and shoot remotely from the computer connected to the camera. Digital Photo Professional This software is recommended for users who shoot RAW images.
Installing the Software Do not connect the camera to your computer before you install the software. The software will not be installed correctly. If there is a previous version of the software already installed on your computer, follow the procedure below to install the latest version. (The previous version will be overwritten.) 1 Insert the EOS DIGITAL Solution Disk into your computer. For Macintosh, double-click to open the CD-ROM icon displayed on the desktop, then double-click on [setup].
Software Instruction Manual Software Instruction Manuals are contained on the EOS DIGITAL Solution Disk. You can copy and view the software instruction manual (PDF files) as follows: 1 Insert the EOS DIGITAL Solution Disk into your computer. 2 Close the install screen. When the EOS DIGITAL Solution Disk install screen appears, close the install screen. 3 Open the CD-ROM. 4 Open the [Manual] folder. 5 Copy the [English] folder to your computer. Instruction Manual PDFs with the names below are copied.
Index Numerics 1:1 (aspect ratio) ...................154, 262 1.3x (crop).............................154, 262 1.6x (crop).............................154, 262 10- or 2-sec. self-timer ..................144 1280x720 (movie) .........................297 16:9 (aspect ratio) .................154, 262 1920x1080 (movie) .......................297 4:3 (aspect ratio) ...................154, 262 61-point automatic selection AF .............................................91, 97 640x480 (movie) .....................
Index Auto switch card ...........................147 Autofocus 9 AF Automatic selection (AF)...........91, 97 Av (Aperture-priority AE).......208, 282 B B (Bulb).................................218, 280 Battery ........................40, 42, 48, 446 Battery Grip.....................48, 446, 454 Beeper ..............................69, 81, 144 Black-and-white images ..........................166, 171, 384 Bracketing AEB (Auto exposure bracketing)........................
Index D D+ .................................................187 Date/time.........................................49 Daylight saving time........................50 DC Coupler ...................................450 Default settings tables...70, 71, 72, 73 Depth-of-field preview ...................209 Detailed information (shooting) .....323 Dials Main Dial.....................................56 Quick Control Dial.......................57 Digital terminal .............
Index Manual flash .............................249 Shutter synchronization (1st/2nd curtain) .......................251 Focus indicator ...............................80 Focus lock.......................................83 Focus mode switch .....6, 52, 141, 275 Focusing 9 AF, Manual Focusing (MF) Focusing point (AF point) ......................90, 93, 95, 99 Folder creation/selection.......194, 195 For editing (ALL-I).........................298 Formatting (card initialization).........67 Frame rate ......
Index Initial AF Point...............................128 Interval timer .................................239 IPB (Standard) ..............................298 ISO speed .....................158, 283, 287 Automatic setting (Auto) ...........160 Automatic setting range............162 ISO expansion ..........................161 Manual setting range ................161 Minimum shutter speed ............163 Setting increments....................402 iTR AF...........................................129 J JPEG....
Index Microphone ...........................280, 301 Mirror lockup .................................234 Mode Dial..................................33, 56 Monochrome (V) ......................166 Monochrome images ....................384 Movies ..........................................279 AE lock .....................................284 AF method........................295, 315 Aperture-priority AE..................282 Attenuator.................................301 Autoexposure shooting.............
Index Pixels ............................149, 151, 157 Playback .......................................319 Portrait (Q) ...............................165 Possible recording time (movie) ..................................291, 298 Possible shots.................48, 151, 257 Power..............................................47 Auto power off ......................47, 69 Battery information ...................446 Battery level........................48, 446 Household power......................
Index Shutter synchronization ................251 Shutter-priority AE ................206, 281 Silent shooting Silent continuous shooting .......142 Silent LV shooting.............266, 315 Silent single shooting ...............142 Single shooting .............................142 Single-image display.....................320 Single-point AF .................90, 95, 271 Single-point Spot AF .................90, 95 Slide show ....................................348 Small (image-recording quality) ......
MEMO 531
The descriptions in this Instruction Manual are current as of February 2017. For information on the compatibility with any products introduced after this date, contact any Canon Service Center. For the latest version Instruction Manual, refer to the Canon Web site. CPX-E312-000 © CANON INC.