EOS 80D (W) Camera Wireless Function Basic Instruction Manual Instruction manuals (PDF files) and software can be downloaded from the Canon Web site (p.4, 233). www.canon.
EOS 80D (W) Camera Basic Instruction Manual The Camera Basic Instruction Manual covers the most basic operations and functions.
Introduction The EOS 80D (W) is a digital single-lens reflex camera featuring a finedetail CMOS sensor with approx. 24.2 effective megapixels, DIGIC 6, high-precision and high-speed 45-point AF (Cross-type AF point: Max. 45 points), max. approx. 7.0 fps continuous shooting, Live View shooting, Full High-Definition (Full HD) movie shooting, and wireless functions (Wi-Fi/NFC).
Item Check List Before starting, check that all the following items are included with your camera. If anything is missing, contact your dealer. Camera (with body cap) Wide Strap Battery Pack LP-E6N (with protective cover) Battery Charger LC-E6/LC-E6E* * Battery Charger LC-E6 or LC-E6E is provided. (The LC-E6E comes with a power cord.) The camera does not come with an interface cable or HDMI cable. The Instruction Manuals provided are listed on the next page.
Instruction Manuals Camera and Wireless Function Basic Instruction Manual The booklet is the Basic Instruction Manual. More detailed Instruction Manuals (PDF files) can be downloaded from the Canon Web site. Downloading and Viewing the Instruction Manuals (PDF Files) 1 Download the Instruction Manuals (PDF files). Connect to the Internet and access the following Canon Web site. www.canon.com/icpd Select your country or region of residence and download the Instruction Manuals.
Compatible Cards The following cards can be used with the camera regardless of capacity: If the card is new or was previously formatted by another camera or computer, format the card with this camera (p.58). SD/SDHC*/SDXC* memory cards * UHS-I cards supported. Cards that Can Record Movies When shooting movies, use a large-capacity card with a reading/writing speed class at least as high as shown in the following table. Movie Recording Size (p.
Quick Start Guide Insert the battery (p.30). 1 To charge the battery, see page 28. Insert the card (p.31). 2 3 With the card’s label facing toward the back of the camera, insert it into the card slot. White index Red index Attach the lens (p.41). Align the lens’s white or red mount index with the camera’s mount index of the same color. 4 Set the lens’s focus mode switch to (p.41). 5 Set the power switch to <1>, then set the Mode Dial to (Scene Intelligent Auto) (p.72).
Quick Start Guide 6 Flip out the LCD monitor (p.34). 7 Focus on the subject (p.44). 8 Take the picture (p.44). 9 Review the picture. When the LCD monitor displays the date/time/zone setting screens, see page 37. Look through the viewfinder and aim the viewfinder center over the subject. Press the shutter button halfway, and the camera will focus on the subject. If necessary, the built-in flash will be raised. Press the shutter button completely to take the picture.
Conventions Used in this Manual Icons in this Manual <6> : Indicates the Main Dial. <5> : Indicates the Quick Control Dial. <9> : Indicates the Multi-controller and the push direction. <0> : Indicates the Setting button. 0, 9, 7, 8 : Indicates that each function remains active for approx. 4 sec., 6 sec., 10 sec., or 16 sec. after you let go of the button.
Chapters Introduction 2 1 Getting Started 27 2 Basic Shooting 71 3 Setting the AF and Drive Modes 109 4 Image Settings 131 5 Advanced Operations 155 6 Shooting with the LCD Monitor (Live View Shooting) 173 7 Shooting Movies 197 8 Image Playback 215 9 Software Start Guide / Downloading Images to a Computer 231 9
Contents Introduction 2 Item Check List................................................................................. 3 Instruction Manuals .......................................................................... 4 Compatible Cards............................................................................. 5 Quick Start Guide ............................................................................. 6 Conventions Used in this Manual..................................................... 8 Chapters.
Contents Displaying the Grid.......................................................................... 65 Q Displaying the Electronic Level ...............................................66 Displaying the Flicker Detection......................................................68 Feature Guide and Help.................................................................. 69 2 Basic Shooting 71 A Fully Automatic Shooting (Scene Intelligent Auto) ...................
Contents j Using the Self-timer................................................................. 130 4 Image Settings 131 Setting the Image-Recording Quality ........................................... 132 i: Setting the ISO Speed for Still Photos ................................. 135 A Selecting a Picture Style ...................................................... 137 Setting the White Balance ............................................................ 139 White Balance..............................
Contents Shooting Movies 7 197 k Shooting Movies .....................................................................198 Setting the Movie Recording Size.................................................207 8 Image Playback 215 x Image Playback ......................................................................216 B: Shooting Information Display.............................................218 x Searching for Images Quickly.................................................222 u/y Magnified View ...
Safety Precautions The following precautions are provided to prevent harm or injury to yourself and others. Make sure to thoroughly understand and follow these precautions before using the product. If you experience any malfunctions, problems, or damage to the product, contact the nearest Canon Service Center or the dealer from whom you purchased the product. Warnings: Follow the warnings below. Otherwise, death or serious injuries may result.
Safety Precautions When the camera or accessories are not in use, make sure to remove the battery, and disconnect the power plug and connecting cables from the equipment before storing. This is to prevent electrical shock, excessive heat, fire, and corrosion. Do not use the equipment where there is flammable gas. This is to prevent an explosion or a fire. If you drop the equipment and the casing breaks open to expose the internal parts, do not touch the exposed parts.
Safety Precautions Cautions: Follow the cautions below. Otherwise, physical injury or property damage may result. Do not use or store the product in a high-temperature location such as inside a car under the hot sun. The product may become hot and cause burns. Doing so may also cause battery leakage or explosion, which will degrade the performance or shorten the life of the product. Do not carry the camera around when it is attached to a tripod. Doing so may cause an injury or an accident.
Handling Precautions Camera Care This camera is a precision instrument. Do not drop it or subject it to physical shock. The camera is not waterproof and cannot be used underwater. If you accidentally drop the camera into water, promptly consult the nearest Canon Service Center. Wipe off any water droplets with a dry and clean cloth. If the camera has been exposed to salty air, wipe it with a clean, well-wrung wet cloth.
Handling Precautions If condensation forms on the camera, do not use the camera. This is to avoid damaging the camera. If there is condensation, remove the lens, card and battery from the camera, and wait until condensation has evaporated before using the camera. If the camera will not be used for an extended period, remove the battery and store the camera in a cool, dry, well-ventilated location.
Handling Precautions Cards To protect the card and its recorded data, note the following: Do not drop, bend, or wet the card. Do not subject it to excessive force, physical shock, or vibration. Do not touch the card’s electronic contacts with your fingers or anything metallic. Do not affix any stickers, etc., on the card. Do not store or use the card near anything that has a strong magnetic field, such as a TV set, speakers, or magnets. Also avoid places prone to having static electricity.
Nomenclature LCD panel (p.22) Drive mode selection button (p.128) AF operation selection button (p.110) ISO speed setting button (p.135) Built-in flash/AF-assist beam emitter (p.170/113) Metering mode selection button (p.164) EF lens mount index (p.41) AF area selection mode button (p.115) EF-S lens mount index (p.41) Flash sync contacts Hot shoe <6> Main Dial (p.45) Flash button (p.170) Mode Dial lockrelease button (p.45) LCD panel illumination button (p.
Nomenclature
AF start button (p.44, 110, 175, 206) Focal plane mark (p.91) Live View shooting/ Movie shooting switch (p.174/198) <0> Start/Stop button (p.174, 198) AE lock/FE lock button/ Index/Reduce button (p.169/222, 223) Dioptric adjustment knob (p.43) Speaker (p.226) Eyecup AF point selection/ Magnify button (p.116/223) Viewfinder eyepiece Power switch (p.35) Access lamp (p.33) Strap mount (p.27) Menu button (p.52) Info button (p.
Nomenclature LCD Panel Drive mode (p.128) u Single shooting o High-speed continuous shooting i Low-speed continuous shooting B Silent single shooting M Silent continuous shooting Q Self-timer: 10 sec./remote control k Self-timer: 2 sec./remote control Highlight tone priority (p.147) ISO speed (p.135) ISO speed (p.
Nomenclature Viewfinder Information Single-point AF (Manual selection) (p.114) Focusing screen Area AF frame (p.114) Zone AF (Manual selection of zone) (p.114) Large Zone AF (Manual selection of zone) (p.114) 45-point automatic selection AF (p.114) AF point (p.114) Grid (p.65) Aspect ratio line Spot metering circle (p.164) Flicker detection (p.68, 152) Electronic level (p.67) Battery level (p.36) AE lock (p.169) / AEB in-progress (p.167) Flash-ready (p.
Nomenclature Mode Dial Turn the Mode Dial while holding down the Mode Dial center (Mode Dial lock-release button). Basic Zone All you do is press the shutter button. The camera sets everything to suit the subject or scene for shooting. A 7 C 8 P : Scene Intelligent Auto (p.72) : Flash Off (p.77) : Creative Auto (p.78) : Special scene (p.82) Food (p.83) G HDR Backlight Control (p.88) C Kids (p.84) 2 Portrait (p.89) x Candlelight (p.85) 3 Landscape (p.90) 6 Night Portrait (p.86) 4 Close-up (p.
Nomenclature Creative Zone These modes give you more control for shooting various subjects as desired. d : Program AE (p.156) s : Shutter-priority AE (p.158) f : Aperture-priority AE (p.160) a : Manual exposure (p.162) F : Bulb Custom shooting mode You can register the shooting mode (d/s/f/a/F), AF operation, menu settings, etc., to w, x Mode Dial positions.
Nomenclature Battery Charger LC-E6 Charger for Battery Pack LP-E6N/LP-E6 (p.28). Power plug Battery pack slot Charge lamp IMPORTANT SAFETY INSTRUCTIONS-SAVE THESE INSTRUCTIONS. DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS. For connection to a supply not in the U.S.A., use an attachment plug adapter of the proper configuration for the power outlet, if needed. Battery Charger LC-E6E Charger for Battery Pack LP-E6N/LP-E6 (p.28).
1 Getting Started This chapter explains preparatory steps before you start shooting and basic camera operations. Attaching the Strap Pass the end of the strap through the camera’s strap mount eyelet from the bottom. Then pass it through the strap’s buckle as shown in the illustration. Pull the strap to take up any slack and make sure the strap will not loosen from the buckle. The eyepiece cover is attached to the strap.
Charging the Battery 1 Remove the protective cover. Detach the protective cover provided with the battery. the battery. 2 Attach As shown in the illustration, attach the battery securely to the charger. To detach the battery, follow the above procedure in reverse. LC-E6 the battery. 3 Recharge For LC-E6 As shown by the arrow, flip out the battery charger’s prongs and insert the prongs into a power outlet.
Charging the Battery Tips for Using the Battery and Charger Upon purchase, the battery is not fully charged. Charge the battery before use. Recharge the battery on the day before or on the day it is to be used. Even during storage, a charged battery will gradually drain and lose its capacity. After recharging the battery, detach it and disconnect the charger from the power outlet. You can attach the cover in a different orientation to indicate whether the battery has been recharged or not.
Installing and Removing the Battery Load a fully-charged Battery Pack LP-E6N (or LP-E6) into the camera. The camera’s viewfinder becomes bright when a battery is installed, and darkens when the battery is removed. If the battery is not installed, the picture in the viewfinder becomes blurred and focus cannot be achieved. Installing the Battery 1 Open the cover. Slide the lever as shown by the arrows and open the cover. the battery. 2 Insert Insert the end with the electrical contacts.
Installing and Removing the Card You can use an SD, SDHC, or SDXC memory card (sold separately) with the camera. SDHC and SDXC memory cards with UHS-I can also be used. The captured images are recorded onto the card. Make sure the card’s write-protect switch is set upward to enable writing and erasing. Installing the Card 1 Write-protect switch Open the cover. Slide the cover as shown by the arrows to open it. the card.
Installing and Removing the Card The number of possible shots depends on the remaining capacity of the card, image-recording quality, ISO speed, etc. Setting [z1: Release shutter without card] to [Disable] will prevent you from shooting without a card inserted. Removing the Card Access lamp 1 Open the cover. Set the power switch to <2>. Make sure the access lamp is off, then open the cover. If [Recording...] is displayed, close the cover. the card.
Installing and Removing the Card When the access lamp is lit or blinking, it indicates that images are being written to, read from, or erased from the card, or data is being transferred. Do not open the card slot cover during this time. Also, never do any of the following while the access lamp is lit or blinking. Otherwise, it can damage the image data, card, or camera. • Removing the card. • Removing the battery. • Shaking or banging the camera around.
Using the LCD Monitor After you flip out the LCD monitor, you can set menu functions, use Live View shooting, shoot movies, or play back images and movies. You can change the direction and angle of the LCD monitor. 1 Flip out the LCD monitor. the LCD monitor. 2 Rotate When the LCD monitor is swung out, 180° 90° 175° you can rotate it up, down, or over 180° to face the subject. The indicated angle is only approximate. it toward you. 3 Face Normally, use the camera with the LCD monitor facing you.
Turning on the Power If you turn on the power switch and the date/time/zone setting screen appears, see page 37 to set the date/time/zone. <1> : The camera turns on. <2> : The camera is turned off and does not function. Set to this position when not using the camera. Automatic Sensor Cleaning Whenever you set the power switch to <1> or <2>, sensor cleaning will be performed automatically. (A small sound may be heard.) During the sensor cleaning, the LCD monitor will display .
Turning on the Power z Battery Level Indicator When the power switch is set to <1>, the battery level will be indicated in one of six levels. A blinking battery icon (b) indicates that the battery will be exhausted soon. Display z x c m Level (%) 100 - 70 69 - 50 49 - 20 19 - 10 Number of Possible Shots bn 9-1 0 (Approx.
3 Setting the Date, Time, and Zone When you turn on the power for the first time or if the date/time/zone have been reset, the date/time/zone setting screen will appear. Follow the steps below to set the time zone first. Set the camera to the time zone in which you currently live so that, when you travel, you can simply change the setting to the correct time zone for your destination, and the camera will automatically adjust the date/time.
3 Setting the Date, Time, and Zone Select the [Zone] box, then press <0>. Press the keys to select the time zone, then press <0>. If you do not see your time zone, you can also set the time difference with UTC directly. In such a case, press the keys to select the [Time difference] box, then press <0> so is displayed. Press the keys to set, then press <0>. (Returns to .) After setting, press the keys to select [OK], then press <0>.
3 Setting the Date, Time, and Zone the setting. 6 Exit Press the keys to select [OK], then press <0>. The date/time/zone and daylight saving time will be set and the menu will reappear. The date/time/zone settings may be reset in the following cases. If this happens, set the date/time/zone again. • When the camera is stored without the battery. • When the camera’s battery becomes exhausted. • When the camera is exposed to below freezing temperatures for a prolonged period.
3 Selecting the Interface Language 1 Display the menu screen. Press the button to display the menu screen. the [52] tab, select 2 Under [LanguageK]. Press the button and select the [5] tab. Press the keys to select the [52] tab. Press the keys to select the [LanguageK], then press <0>. the desired language. 3 Set Press the keys to select the language, then press <0>. The interface language will change.
Attaching and Detaching a Lens The camera is compatible with all Canon EF and EF-S lenses. The camera cannot be used with EF-M lenses. Attaching a Lens 1 Remove the caps. Remove the rear lens cap and the body cap by turning them as shown by the arrows. the lens. 2 Attach Align the lens’s red or white index White index with the camera’s index matching the same color. Turn the lens as shown by the arrow until it clicks in place. Red index the lens’s focus mode switch 3 Set to .
Attaching and Detaching a Lens Zooming Turn the zoom ring on the lens with your fingers. If you want to zoom, do it before focusing. Turning the zoom ring after achieving focus may throw off the focus. Detaching the Lens While pressing the lens release button, turn the lens as shown by the arrow. Turn the lens until it stops, then detach it. Attach the rear lens cap to the detached lens. Do not look at the sun directly through any lens. Doing so may cause loss of vision.
Basic Operation Adjusting the Viewfinder Clarity Turn the dioptric adjustment knob. Turn the knob left or right so that the AF points in the viewfinder look the sharpest. If the knob is difficult to turn, remove the eyecup. If the camera dioptric adjustment still cannot provide a sharp viewfinder image, using E-series Dioptric Adjustment Lenses (sold separately) is recommended. Holding the Camera To obtain sharp images, hold the camera still to minimize camera shake.
Basic Operation Shutter Button The shutter button has two steps. You can press the shutter button halfway. Then you can further press the shutter button completely. Pressing Halfway This activates autofocusing and the automatic exposure system that sets the shutter speed and aperture. The exposure setting (shutter speed and aperture) is displayed in the viewfinder and on the LCD panel (0). Pressing Completely This releases the shutter and takes the picture.
Basic Operation Mode Dial Turn the dial while holding down the lock release button at the center of the dial. Use it to set the shooting mode. 6 Main Dial (1) After pressing a button, turn the <6> dial. When you press a button such as , the respective function remains selected for the duration of the timer (9). During this time, you can turn the <6> dial to set the desired setting.
Basic Operation 5 Quick Control Dial (1) After pressing a button, turn the <5> dial. When you press a button such as , the respective function remains selected for the duration of the timer (9). During this time, you can turn the <5> dial to set the desired setting. When the function selection ends or if you press the shutter button halfway, the camera will be ready to shoot. Use this dial to select or set the AF operation, drive mode, ISO speed, metering mode, AF point selection, etc.
Basic Operation 9 Multi-controller The Multi-controller <9> has eight keys that tilt in the directions shown by the arrows. Use the eight keys to select the AF point, correct the white balance, move the AF point or magnifying frame during Live View shooting or movie shooting, or scroll around magnified images during playback. For menus and the Quick Control, the Multi-controller works only in the vertical and horizontal directions . It does not work in diagonal directions.
Basic Operation R Multi Function Lock With [54: Multi function lock] set and the switch set upward, the camera prevents you from changing settings inadvertently by moving the Main Dial, Quick Control Dial, and Multi-controller or by touching the touch panel. switch set downward: Lock released switch set upward: Lock engaged 1 Select [Multi function lock]. Under the [54] tab, select [Multi function lock], then press <0>. a checkmark [X] to the 2 Add camera control to be locked.
Basic Operation U LCD Panel Illumination You can illuminate the LCD panel by pressing the button. Turn on (9) or off the LCD panel illumination by pressing the button. During a bulb exposure, pressing the shutter button completely will turn off the LCD panel illumination. Displaying Shooting Function Settings After you press the button a number of times, the shooting function settings will be displayed.
Q Quick Control for Shooting Functions You can directly select and set the shooting functions displayed on the LCD monitor. This is called Quick Control. 1 Press the button (7). The Quick Control screen will appear. the desired function. 2 Set Press the or keys to select a function. The settings of the selected function and Feature guide (p.69) will appear. Turn the <6> or <5> dial to change the setting. Basic Zone modes Creative Zone modes the picture.
Q Quick Control for Shooting Functions Sample Quick Control Screen Aperture (p.160) Shutter speed (p.158) Shooting mode*1 (p.24) Exposure compensation/ AEB setting (p.166/167) Flash exposure compensation AE lock*2 (p.169) Highlight tone priority*2 (p.147) ISO speed (p.135) Wi-Fi function*3 Picture Style (p.137) Custom Controls AF operation (p.110) Image-recording quality (p.132) Return White balance (p.139) AF area selection mode (p.115) White balance correction Auto Lighting Optimizer (p.
3 Menu Operations You can set various settings with the menus such as the imagerecording quality, date and time, etc. button button <0> button LCD monitor keys Menus in Basic Zone Modes * Some menu tabs and menu items are not displayed in Basic Zone modes.
3 Menu Operations Menu Setting Procedure 1 Display the menu screen. Press the button to display the menu screen. a tab. 2 Select Each time you press the button, the main tab (group of functions) will switch. Press the keys to select a secondary tab. For example, in this manual, the [z3] tab refers to the screen displayed when the z (Shooting) tab’s [3] is selected. the desired item. 3 Select Press the keys to select the item, then press <0>. the setting.
3 Menu Operations In step 2, you can also turn the <6> dial to select a menu tab. In step 4, you can also turn the <5> dial to select certain settings. In steps 2 to 5, you can also use the LCD monitor’s touch screen (p.55). The explanation of menu functions hereafter assumes that you have pressed the button to display the menu screen. To cancel the operation, press the button. Dimmed Menu Items Example: When Multi Shot Noise Reduction is set Dimmed menu items cannot be set.
d Using the Touch Screen The LCD monitor is a touch-sensitive panel that you can operate with your fingers. Tap Sample Display (Quick Control) Use your finger to tap on (touch briefly and then remove your finger from) the LCD monitor. By tapping, you can select menus, icons, etc., displayed on the LCD monitor. When touch-screen operation is possible, a frame will appear around the icon (except on menu screens). For example, when you tap on [Q], the Quick Control screen appears.
d Using the Touch Screen Drag Sample Display (Menu screen) Slide your finger while touching the LCD monitor.
d Using the Touch Screen 3 Touch Control Settings 1 Select [Touch control]. Under the [53] tab, select [Touch control], then press <0>. the touch control setting. 2 Set Select the desired setting, then press <0>. [Standard] is the normal setting. [Sensitive] provides a more reactive touch response than [Standard]. Try using both settings and select the one you prefer. To disable touch-screen operations, select [Disable].
Before You Start 3 Formatting the Card If the card is new or was previously formatted by another camera or computer, format the card with this camera. When the card is formatted, all images and data on the card will be erased. Even protected images will be erased, so make sure there is nothing you need to keep. If necessary, transfer the images and data to a computer, etc., before formatting the card. 1 Select [Format card]. Under the [51] tab, select [Format card], then press <0>. the card.
Before You Start Format the card in the following cases: The card is new. The card was formatted by a different camera or a computer. The card is full of images or data. A card-related error is displayed. Low-level Formatting Perform low-level formatting if the card’s recording or reading speed seems slow or if you want to totally erase data on the card. Since low-level formatting will format all recordable sectors on the card, the formatting will take slightly longer than normal formatting.
Before You Start 3 Disabling the Beeper You can prevent the beeper from sounding when focus is achieved, during self-timer shooting, and for touch screen operations. 1 Select [Beep]. Under the [z1] tab, select [Beep], then press <0>. [Disable]. 2 Select Select [Disable], then press <0>. The beeper will not sound. If [Touch to n] is selected, the beeper will be silent for touch screen operations only.
Before You Start 3 Setting the Image Review Time You can set how long the image is displayed on the LCD monitor immediately after shooting. To keep the image displayed, set [Hold]. To not have the image displayed, set [Off]. 1 Select [Image review]. Under the [z1] tab, select [Image review], then press <0>. the desired time. 2 Set Select the desired setting, then press <0>. If [Hold] is set, the image will be displayed until the auto power off time elapses.
Before You Start 3 Reverting the Camera to the Default SettingsN The camera’s shooting function settings and menu settings can be reverted to their defaults. 1 Select [Clear all camera settings]. Under the [54] tab, select [Clear all camera settings], then press <0>. [OK]. 2 Select Select [OK], then press <0>.
Before You Start Image Recording Settings Image quality 73 Aspect ratio 3:2 Picture Style Auto Auto Lighting Standard Optimizer Lens aberration correction Enable / Correction Peripheral illumination correction data retained 1 min. Enable Enable 2 sec.
Before You Start Live View Shooting Settings Live View shooting AF method AF operation Touch shutter Grid display Exposure simulation Silent LV shooting Metering timer Creative filters Enable u+Tracking X Disable Hide Enable Mode 1 8 sec.
Displaying the Grid You can display a grid in the viewfinder to help you check the camera tilt or compose the shot. 1 Select [Viewfinder display]. Under the [52] tab, select [Viewfinder display], then press <0>. 2 Select [Grid display]. [Show]. 3 Select When you exit the menu, the grid will appear in the viewfinder. You can display a grid on the LCD monitor during Live View shooting and before you start shooting a movie.
Q Displaying the Electronic Level You can display the electronic level on the LCD monitor and in the viewfinder to help you correct the camera tilt. Note that you can check only the horizontal tilt and not the forward/backward tilt. Displaying the Electronic Level on the LCD Monitor 1 Press the button. Each time you press the button, the screen display will change. Display the electronic level.
Q Displaying the Electronic Level 3 Displaying the Electronic Level in the Viewfinder A simple electronic level using a camera icon can be displayed in the viewfinder. Since this indicator is displayed during shooting, you can take the picture while checking the camera tilt. 1 Select [Viewfinder display]. Under the [52] tab, select [Viewfinder display], then press <0>. 2 Select [Electronic level]. 3 Select [Show]. the shutter button halfway.
Displaying the Flicker DetectionN If you set this function, will appear in the viewfinder when the camera detects flicker caused by the blinking of the light source. By default, flicker detection is set to [Show]. 1 Select [Viewfinder display]. Under the [52] tab, select [Viewfinder display], then press <0>. 2 Select [Flicker detection]. 3 Select [Show]. If you set [z4: Anti-flicker shoot.] to [Enable], you can shoot with reduced unevenness of exposure caused by the flicker.
Feature Guide and Help The Feature guide and Help display information about camera features. Feature Guide The Feature guide appears when you change the shooting mode or set a shooting function, Live View shooting, movie shooting, or Quick Control for playback, and displays a brief description of that mode, function or option. It also displays a description when you select a function or option with Quick Control. The Feature guide turns off when you tap on the description or proceed with the operation.
Feature Guide and Help v Help When [zHelp] is displayed at the bottom of the menu screen, pressing the button displays the function’s description (Help). If the Help fills more than one screen, a scroll bar will appear on the right edge. You can turn the <5> dial or press the keys to scroll. Example: [z3: Long exp. noise reduction] B Scroll bar Example: [8C.Fn I-1: Exposure level increments] B Example: [8C.
2 Basic Shooting This chapter explains how to use the Basic Zone modes on the Mode Dial for best results. e With Basic Zone modes, all you do is point and shoot, and the camera sets everything automatically (p.101). Also, to prevent botched pictures due to misoperations, advanced shooting function settings cannot be changed. Ba s ic n Zo Before Shooting in the <8> or Mode When the LCD monitor is turned off, press the button or button (p.
A Fully Automatic Shooting (Scene Intelligent Auto) is a fully automatic mode. The camera analyzes the scene and sets the optimum settings automatically. It also adjusts focus automatically by detecting whether the subject is still or moving (p.75). 1 Area AF frame Set the Mode Dial to . Turn the Mode Dial while holding down the lock release button at the center. the Area AF frame over the 2 Aim subject. All the AF points will be used to focus, and the camera will focus on the closest object.
A Fully Automatic Shooting (Scene Intelligent Auto) the picture. 4 Take Press the shutter button completely to take the picture. The captured image will be displayed for approx. 2 sec. on the LCD monitor. After you finish shooting, push down the built-in flash with your fingers. The mode makes the colors look more impressive in nature, outdoor, and sunset scenes.
A Fully Automatic Shooting (Scene Intelligent Auto) The beeper continues to beep softly. (The focus indicator does not light up.) It indicates that the camera is focusing continuously on a moving subject. (The focus indicator does not light up.) You can take sharp pictures of a moving subject. Note that the focus lock (p.75) will not work in this case. Pressing the shutter button halfway does not focus on the subject.
A Full Auto Techniques (Scene Intelligent Auto) Recomposing the Shot Depending on the scene, position the subject toward the left or right to create a balanced background and good perspective. In the mode, pressing the shutter button halfway to focus on a still subject will lock the focus on that subject. Recompose the shot while keeping the shutter button pressed halfway, and then press the shutter button completely to take the picture. This is called “focus lock”.
A Full Auto Techniques (Scene Intelligent Auto) A Live View Shooting You can shoot while viewing the image on the LCD monitor. This is called “Live View shooting”. For details, see page 173. the Live View shooting/Movie 1 Set shooting switch to . the Live View image on 2 Display the LCD monitor. Press the <0> button. The Live View image will appear on the LCD monitor. on the subject. 3 Focus Press the shutter button halfway to focus.
7 Disabling Flash The camera analyzes the scene and sets the optimum settings automatically. In places where flash photography is prohibited such as in a museum or an aquarium, use the <7> (Flash Off) mode. Shooting Tips Prevent camera shake if the numeric display (shutter speed) in the viewfinder blinks. Under low light when camera shake is prone to occur, the viewfinder’s shutter speed display will blink. Hold the camera steady or use a tripod.
C Creative Auto Shooting In the mode, you can set the following functions for shooting: (1) Ambience-based shots, (2) Background blur, (3) Drive mode, and (4) Built-in flash firing. The default settings are the same as the mode. * CA stands for Creative Auto. 1 Set the Mode Dial to . the button (7). 2 Press The Quick Control screen will appear. the desired function. 3 Set Press the or keys to select a function.
C Creative Auto Shooting Shutter speed Aperture ISO speed (3) Battery level Image-recording quality (1) (2) (4) Possible shots If you set (1) or (2) when the camera is set for Live View shooting, you can see the effect on the screen before you start shooting. (1) Ambience-based shots You can select and shoot with the ambience you want to convey in your images. Turn the <6> or <5> dial to select the ambience. You can also select it from a list by pressing <0>. For details, see page 102.
C Creative Auto Shooting (2) Background blur • If [OFF] is set, the degree of background blur will change depending on the brightness. • If it is set to any setting other than [OFF], you can adjust the background blur regardless of the brightness. • If you turn the <6> or <5> dial to move the cursor to the right, the background will look sharper. • Turning the <6> or <5> dial to move the cursor to the left will blur the subject’s background.
C Creative Auto Shooting (3) Drive mode: Use the <6> or <5> dial to make the selection. You can also select it from a list by pressing <0>. Single shooting: Shoot one image at a time. High-speed continuous shooting: While you hold down the shutter button completely, shots will be taken continuously. You can shoot up to approx. 7.0 shots per second. Low-speed continuous shooting: While you hold down the shutter button completely, shots will be taken continuously. You can shoot up to approx. 3.
8: Special Scene Mode The camera will automatically choose the appropriate settings when you select a shooting mode for your subject or scene. 1 Set the Mode Dial to <8>. the button (7). 2 Press The Quick Control screen will appear. a shooting mode. 3 Select Press the or keys to select the desired shooting mode’s icon. Turn the <6> or <5> dial to select a shooting mode.
P Shooting Food When shooting food, use
(Food). The photo will look bright and appetizing. Also, depending on the light source, the reddish tinge will be suppressed in the pictures taken under tungsten lights, etc. Shooting Tips Change the color tone. You can change [Color tone]. To increase the food’s reddish tinge, set it toward [Warm]. Set it toward [Cool] if it looks too red. Avoid using flash. If you use flash, the light may reflect off the dish or food and results in unnatural shadows.
C Shooting Children When you want to continuously focus on and shoot children running around, use (Kids). Skin tones will look healthy. Shooting Tips Track the subject with the Area AF frame. Press the shutter button halfway to start autofocusing in Area AF frame. During autofocusing, the beeper will continue beeping softly. If focus cannot be achieved, the focus indicator will blink. Shoot continuously. The default setting is (High-speed continuous shooting*).
x Shooting Candlelight Portraits When shooting a human subject in candlelight, use (Candlelight). The candlelight color tones will be retained in the photo. Shooting Tips Use the center AF point to focus. Aim the center AF point in the viewfinder over the subject, then shoot. Prevent camera shake if the numeric display (shutter speed) in the viewfinder blinks. Under low light when camera shake is prone to occur, the viewfinder’s shutter speed display will blink.
6 Shooting Night Portraits (With a Tripod) To shoot people at night and obtain a natural-looking night scene in the background, use the <6> (Night Portrait) mode. Using a tripod is recommended. Shooting Tips Use a wide-angle lens and a tripod. When using a zoom lens, use the wide-angle end to obtain a wide night view. Also, use a tripod to prevent camera shake. Check the subject’s brightness. Under low light, the built-in flash will fire automatically to obtain a good exposure of the subject.
F Shooting Night Scenes (Handheld) Using a tripod when shooting a night scene gives the best results. However, the (Handheld Night Scene) mode enables you to shoot night scenes even while handholding the camera. In this shooting mode, four shots are taken continuously for each picture, and the resulting one image with reduced camera shake is recorded. Shooting Tips Hold the camera firmly. While shooting, hold the camera firmly and steadily.
G Shooting Backlit Scenes When shooting a scene having both bright and dark areas, use the (HDR Backlight Control) mode. When you take one picture in this mode, three continuous shots are taken at different exposures. This results in one image, with a wide tonal range, that has minimized the clipped shadows caused by backlighting. Shooting Tips Hold the camera firmly. While shooting, hold the camera firmly and steadily. In this mode, three shots are aligned and merged into a single image.
2 Shooting Portraits The <2> (Portrait) mode blurs the background to make the human subject stand out. It also makes skin tones and hair look softer. Shooting Tips Select the location where the distance between the subject and the background is the farthest. The further the distance between the subject and background, the more blurred the background will look. The subject will also stand out better against an uncluttered dark background. Use a telephoto lens.
3 Shooting Landscapes Use the <3> (Landscape) mode for wide scenery or to have everything in focus from near to far. For vivid blues and greens, and very sharp and crisp images. Shooting Tips With a zoom lens, use the wide-angle end. When using the wide-angle end of a zoom lens, objects near and far will be in focus better than at the telephoto end. It also adds breadth to landscapes. Shooting night scenes. The <3> mode is also good for night scenes because it disables the built-in flash.
4 Shooting Close-ups When you want to shoot flowers or small things up close, use the <4> (Close-up) mode. To make small things appear much larger, use a macro lens (sold separately). Shooting Tips Use a simple background. A simple background makes small objects such as flowers stand out better. Move in as close as possible to the subject. Check the lens for its minimum focusing distance. Some lenses have indications such as on them.
5 Shooting Moving Subjects Use the <5> (Sports) mode to shoot a moving subject, such as a running person or a moving vehicle. Shooting Tips Use a telephoto lens. The use of a telephoto lens is recommended for shooting from a distance. Track the subject with the Area AF frame. Press the shutter button halfway to start autofocusing in Area AF frame. During autofocusing, the beeper will continue beeping softly. If focus cannot be achieved, the focus indicator will blink.
Cautions for Kids During Live View shooting, the image quality can be set to 1 or JPEG. If 41 or 61 is set, the image will be recorded in 1 quality. During Live View shooting, if flash is fired in continuous shooting, the continuous shooting speed will decrease. Even if the flash is not fired for subsequent shots, shooting will be performed with the decreased continuous shooting speed.
Cautions for Handheld Night Scene When shooting with flash, if the subject is too close to the camera, the picture may come out extremely bright (overexposure). If you use flash to shoot a night scene with few lights, the shots may not align correctly. This can result in a blurry picture. If you use flash and the human subject is close to the background that is also illuminated by the flash, the shots may not align correctly. This can result in a blurry picture.
v Applying Creative Filters In the (Creative filter) mode, you can apply one of ten filter effects (Grainy B/W*, Soft focus*, Fish-eye effect*, Toy camera effect*, Miniature effect*, Water painting effect*, HDR art standard, HDR art vivid, HDR art bold, and HDR art embossed) for shooting. When the camera is set for Live View shooting, you can see the effect on the screen before you start shooting. The camera saves only the image with the Creative filter applied.
v Applying Creative Filters a shooting mode. 5 Select Press the or keys to select a shooting mode, then press <0> and select [OK]. The image will be displayed with the effects of the filter applied. For the Miniature effect, press the keys to move the white frame to where you want the image to look sharp. Available Shooting Modes in the v Mode Shooting Mode Page Shooting Mode Water painting effect Page G Grainy B/W p.97 Z W Soft focus p.97 A HDR art standard p.
v Applying Creative Filters You cannot select RAW or RAW+JPEG. If RAW is set, the image will be recorded in the 73 quality. Also, if RAW+JPEG is set, the image will be recorded in the set JPEG quality. When , , , , , or is set, continuous shooting cannot be set. Dust Delete Data will not be appended to images shot with Fish-eye effect applied. is set to (Flash Off) by default. Try to prevent camera shake when shooting in low-light conditions.
v Applying Creative Filters X Fish-eye effect Gives the effect of a fish-eye lens. The image will have a barrel-type distortion. Depending on the level of this filter effect, the area trimmed along the periphery of the image changes. Also, since this filter expands the center part of the image, the resolution at the center may decrease depending on the number of recorded pixels. Check the image on the screen when setting this filter. The AF point will be fixed at center.
v Applying Creative Filters B HDR art vivid The colors are more saturated than with [HDR art standard], and the low contrast and flat gradation create a graphic art effect. C HDR art bold The colors are the most saturated, making the subject pop out, and the picture look like an oil painting. D HDR art embossed The color saturation, brightness, contrast and gradation are decreased to make the picture look flat. The picture looks faded and old.
Q Quick Control In Basic Zone modes, when the shooting function settings are displayed, you can press the button to display the Quick Control screen. The tables on the next page show the functions that can be set with the Quick Control screen in each Basic Zone mode. Example: Portrait mode the Mode Dial to a Basic Zone 1 Set mode. the button (7). 2 Press The Quick Control screen will appear. the desired function. 3 Set Press the or keys to select a function.
Q Quick Control Settable Functions in Basic Zone Modes o: Default setting*1 k: User selectable Function u: Single shooting o: High-speed continuous shooting Drive mode (p.128) i: Low-speed continuous shooting B: Silent single shooting*2 M: Silent continuous shooting*2 Self-timer (p.130) Built-in flash firing Q k a: Automatic firing D: Flash on (Fires at all times) b: Flash off A 7 C o k k k k k k o k k o k k k k k k o k k k o k k k k k k o Ambience-based shots (p.
Shooting with Ambience Selection In Basic Zone modes, when a mode other than , <7>, <8: G>, and is set, you can select the ambience for shooting.
Shooting with Ambience Selection the ambience effect. 5 Set Press the keys to select the effect so that [Effect] appears at the bottom of the screen. Press the keys to select the desired effect. the picture. 6 Take Press the shutter button completely to take the picture. To return to viewfinder shooting, press the <0> button to exit Live View shooting. Then press the shutter button completely to take the picture.
Shooting with Ambience Selection Ambience Settings 1Standard setting Standard image characteristics for the respective shooting mode. Note that <2> has image characteristics geared for portraits and <3> is geared for landscapes. Each ambience is a modification of the respective shooting mode’s image characteristics. 2 Vivid The subject will look sharp and vivid. It makes the photo look more impressive than with [1 Standard setting]. 3 Soft The subject will look softer and more dainty.
Shooting with Ambience Selection 7 Brighter The picture will look brighter. 8 Darker The picture will look darker. 9 Monochrome The picture will be monochrome. You can select the monochrome color to be blue, black and white, or sepia. When [Monochrome] is selected, will appear in the viewfinder.
Shooting by Lighting or Scene Type In the <8: C2345> Basic Zone modes, you can shoot with the settings matching the lighting or scene type. Normally, [e Default setting] is adequate, but if the settings match the lighting condition or scene, the picture will look more accurate to your eyes. For Live View shooting, if you set both [Light/scene-based shots] and [Ambience-based shots] (p.102), you should first set [Light/scenebased shots].
Shooting by Lighting or Scene Type Quick Control, select the 4 With lighting or scene type. Press the button (7). Press the keys to select [e Default setting]. [Light/scenebased shots] will appear on the screen. Press the keys to select the lighting or scene type. The resulting image with the selected lighting or scene type will be displayed. the picture. 5 Take Press the shutter button completely to take the picture.
Shooting by Lighting or Scene Type Lighting or Scene Type Settings eDefault setting Default setting suited for most subjects. fDaylight For subjects under sunlight. Gives more natural-looking blue skies and greenery and reproduces light-colored flowers better. gShade For subjects in the shade. Suitable for skin tones, which may look too bluish, and for light-colored flowers. SCloudy For subjects under overcast skies.
3 Setting the AF and Drive Modes The AF points in the viewfinder are arranged to make AF shooting suitable for a wide variety of subjects and scenes. You can also select the AF operation and drive mode that best match the shooting conditions and subject. The O icon at the upper right of the page title indicates that the function is available only in Creative Zone modes (d/ s/f/a/F). In Basic Zone modes, the AF operation and AF point (AF area selection mode) are set automatically.
f: Selecting the AF OperationN You can select the AF operation characteristics to suit the shooting conditions or subject. In Basic Zone modes, the optimum AF operation is set automatically for the respective shooting mode. 1 Set the lens’s focus mode switch to . the Mode Dial to a Creative 2 Turn Zone mode. 3 Press the button (9). the AF operation. 4 Select While looking at the LCD panel, turn the <6> or <5> dial.
f: Selecting the AF OperationN One-Shot AF for Still Subjects Suited for still subjects. When you press the shutter button halfway, the camera will focus only once. When focus is achieved, the AF point that achieved focus will be displayed, and the focus indicator in the viewfinder will also light up. With evaluative metering, the AF point exposure setting will be set at the Focus indicator same time focus is achieved. While you hold down the shutter button halfway, the focus will be locked.
f: Selecting the AF OperationN AI Servo AF for Moving Subjects This AF operation is suited for moving subjects when the focusing distance keeps changing. While you hold down the shutter button halfway, the camera will keep focusing on the subject continuously. The exposure is set at the moment the picture is taken. When the AF area selection mode (p.114) is set to 45-point automatic selection AF, focus tracking will continue as long as the Area AF frame covers the subject.
f: Selecting the AF OperationN AF Points Lighting Up in Red By default, the AF points light up in red when focus is achieved in lowlight conditions. In Creative Zone modes, you can set whether to have the AF points light up in red when focus is achieved. AF-Assist Beam with the Built-in Flash Under low-light conditions, when you press the shutter button halfway, the built-in flash may fire a brief burst of flashes. This illuminates the subject to help autofocusing.
S Selecting the AF Area and AF PointN The camera has 45 AF points for autofocusing. You can select the AF area selection mode and AF point(s) suiting the scene or subject. Depending on the lens attached to the camera, the number of usable AF points, AF point patterns, the shape of Area AF frame, etc. will differ. For details, see “Lenses and Usable AF Points” on page 119. AF Area Selection Mode You can select one of four AF area selection modes. See the next page for the selection procedure.
S Selecting the AF Area and AF PointN Selecting the AF Area Selection Mode 1 Press the or button (9). Look through the viewfinder and press the or button. the button. 2 Press Each time you press the AF area selection mode button, the AF area selection mode changes. The AF area selection mode currently set is indicated on the top of the viewfinder. With [8C.Fn II-8: Select AF area selec. mode], you can limit the selectable AF area selection modes. If you set [8C.
S Selecting the AF Area and AF PointN Selecting the AF Point Manually You can manually select the AF point or zone. 1 Press the or button (9). The AF points will be displayed in the viewfinder. In the Zone AF mode or Large Zone AF mode, the selected zone will be displayed. an AF point. 2 Select The AF point selection will change in the direction you tilt <9>. If you press <0>, the center AF point (or center zone) will be selected.
S Selecting the AF Area and AF PointN AF Point Display Indications Pressing the or button lights up the AF points that are cross-type AF points for high-precision autofocusing. The blinking AF points are horizontal-line or vertical-line sensitive. For details, see pages 118-122.
AF Sensor The camera’s AF sensor has 45 AF points. The illustration below shows the AF sensor pattern corresponding to each AF point. When using lenses with a maximum aperture of f/2.8 or faster, high-precision AF is possible with the center AF point in the viewfinder. Depending on the lens attached to the camera, the number of usable AF points, AF point patterns, the shape of Area AF frame, etc. vary. For details, see “Lenses and Usable AF Points” on page 119. Diagram Cross-type focusing: f/5.
Lenses and Usable AF Points Although the camera has 45 AF points, the number of usable AF points and focusing patterns vary depending on the lens. The lenses are thereby classified into eight groups from A to H. When using a lens in Groups E to H, fewer AF points will be usable. See which group each lens belongs to on pages 123-126. Check which group the lens in use belongs to. The number of available AF points varies depending on aspect ratio settings.
Lenses and Usable AF Points Group B Autofocusing with 45 points is possible. All the AF area selection modes are selectable. : Cross-type AF point. Subject tracking is superior and highprecision focusing is achieved. Group C Autofocusing with 45 points is possible. All the AF area selection modes are selectable. : Cross-type AF point. Subject tracking is superior and highprecision focusing is achieved. : AF points sensitive to horizontal lines. Group D Autofocusing with 45 points is possible.
Lenses and Usable AF Points Group E Autofocusing with only 35 points is possible. (Not possible with all 45 AF points.) All the AF area selection modes are selectable. During automatic AF point selection, the outer frame marking the AF area (Area AF frame) will be different from 45-point automatic selection AF. : Cross-type AF point. Subject tracking is superior and highprecision focusing is achieved. : AF points sensitive to horizontal lines. : Disabled AF points (not displayed).
Lenses and Usable AF Points Group G Autofocusing with only 27 points is possible. (Not possible with all 45 AF points.) Large Zone AF (manual selection of zone) cannot be selected for AF area selection mode. During automatic AF point selection, the outer frame marking the AF area (Area AF frame) will be different from 45-point automatic selection AF. : Cross-type AF point. Subject tracking is superior and highprecision focusing is achieved. : AF points sensitive to horizontal lines.
Lenses and Usable AF Points Lens Group Designations (as of the release of EOS 80D (W)) EF-S24mm f/2.8 STM EF-S60mm f/2.8 Macro USM EF-S10-18mm f/4.5-5.6 IS STM EF-S10-22mm f/3.5-4.5 USM EF-S15-85mm f/3.5-5.6 IS USM EF-S17-55mm f/2.8 IS USM EF-S17-85mm f/4-5.6 IS USM EF-S18-55mm f/3.5-5.6 EF-S18-55mm f/3.5-5.6 USM EF-S18-55mm f/3.5-5.6 II EF-S18-55mm f/3.5-5.6 II USM EF-S18-55mm f/3.5-5.6 III EF-S18-55mm f/3.5-5.6 IS EF-S18-55mm f/3.5-5.6 IS II EF-S18-55mm f/3.5-5.6 IS STM EF-S18-135mm f/3.5-5.
Lenses and Usable AF Points EF200mm f/2.8L II USM + Extender EF1.4x I/II/III EF200mm f/2.8L II USM + Extender EF2x I/II/III EF300mm f/2.8L USM EF300mm f/2.8L USM + Extender EF1.4x I/II/III EF300mm f/2.8L USM + Extender EF2x I/II/III EF300mm f/2.8L IS USM EF300mm f/2.8L IS USM + Extender EF1.4x I/II/III EF300mm f/2.8L IS USM + Extender EF2x I/II/III EF300mm f/2.8L IS II USM EF300mm f/2.8L IS II USM + Extender EF1.4x I/II/III EF300mm f/2.
Lenses and Usable AF Points EF800mm f/5.6L IS USM + Extender EF1.4x I/II/III EF1200mm f/5.6L USM EF1200mm f/5.6L USM + Extender EF1.4x I/II/III EF8-15mm f/4L Fisheye USM EF11-24mm f/4L USM EF16-35mm f/2.8L USM EF16-35mm f/2.8L II USM EF16-35mm f/4L IS USM EF17-35mm f/2.8L USM EF17-40mm f/4L USM EF20-35mm f/2.8L EF20-35mm f/3.5-4.5 USM EF22-55mm f/4-5.6 USM EF24-70mm f/2.8L USM EF24-70mm f/2.8L II USM EF24-70mm f/4L IS USM EF24-85mm f/3.5-4.5 USM EF24-105mm f/3.5-5.
Lenses and Usable AF Points EF70-200mm f/4L IS USM EF70-200mm f/4L IS USM + Extender EF1.4x I/II/III EF70-200mm f/4L IS USM + Extender EF2x I/II/III EF70-210mm f/3.5-4.5 USM EF70-210mm f/4 EF70-300mm f/4-5.6 IS USM EF70-300mm f/4-5.6L IS USM EF70-300mm f/4.5-5.6 DO IS USM EF75-300mm f/4-5.6 EF75-300mm f/4-5.6 USM EF75-300mm f/4-5.6 II EF75-300mm f/4-5.6 II USM EF75-300mm f/4-5.6 III EF75-300mm f/4-5.6 III USM EF75-300mm f/4-5.6 IS USM EF80-200mm f/2.8L EF80-200mm f/4.5-5.6 EF80-200mm f/4.5-5.
MF: Manual Focus 1 Set the lens’s focus mode switch to . <4 L> will be displayed on the LCD panel. Focusing ring on the subject. 2 Focus Focus by turning the lens’s focusing ring until the subject looks sharp in the viewfinder. If you press the shutter button halfway during manual focusing, the AF point that achieved focus and the focus indicator will light up in the viewfinder.
i Selecting the Drive Mode Single and continuous drive modes are provided. 1 Press the button (9). the drive mode. 2 Select While looking at the LCD panel, turn the <6> or <5> dial. u : Single shooting When you press the shutter button completely, only one shot will be taken. o: High-speed continuous shooting (Max. approx. 7.0 shots/sec.*) While you hold down the shutter button completely, the camera will shoot continuously.
i Selecting the Drive Mode o: The maximum continuous shooting speed of approx. 7.0 shots/sec. is attained under the following conditions*: 1/500 sec. or faster shutter speed, maximum aperture (varies depending on the lens), Anti-flicker shooting set to Disable, with a fully-charged Battery Pack LP-E6N, and at room temperature (23°C/73°F).
j Using the Self-timer Use the self-timer when you want to be in the picture. 1 Press the button (9). the self-timer. 2 Select While looking at the LCD panel, turn the <6> or <5> dial to select the self-timer delay. Q : Shoot in approx. 10 sec. k : Shoot in approx. 2 sec. the picture. 3 Take Look through the viewfinder, focus on the subject, then press the shutter button completely.
4 Image Settings This chapter explains image-related function settings: Image-recording quality, ISO speed, Picture Style, white balance, Auto Lighting Optimizer, noise reduction, lens aberration correction, anti-flicker shooting, and other functions. The O icon at the upper right of the page title indicates that the function is available only in Creative Zone modes (d/ s/f/a/F).
3 Setting the Image-Recording Quality You can select the pixel count and the image quality. There are eight JPEG image-recording quality settings: 73, 83, 74, 84, 7a, 8a, b, c. There are three RAW image quality settings: 1, 41, 61 (p.134). 1 Select [Image quality]. Under the [z1] tab, select [Image quality], then press <0>. the image-recording quality. 2 Set To select a RAW setting, turn the <6> dial. To select a JPEG setting, press the keys.
3 Setting the Image-Recording Quality Guide to Image-Recording Quality Settings (Approx.) Image Quality 73 83 74 JPEG 84 7a Pixels Printing Recorded Size 24M A2 11M A3 File Size (MB) Possible Maximum Burst Shots 7.6 940 77 (110) 3.9 1800 120 (120) 4.1 1730 140 (140) 2.0 3430 140 (140) 2.6 2700 140 (140) 1.3 5260 150 (150) 5.9M A4 b*1 2.5M 9x13 cm 1.3 5260 150 (150) c*2 0.3M - 0.3 20180 150 (150) 1 20 (25) 8a 24M A2 28.9 240 RAW 41 14M A3 22.
3 Setting the Image-Recording Quality If you select both RAW and JPEG, the same image will be recorded simultaneously to the card in both RAW and JPEG at the imagerecording qualities that were set. The two images will be recorded with the same file numbers (file extension: .JPG for JPEG and .CR2 for RAW). The image-recording quality icons are as follows: 1 (RAW), 41 (Middle RAW), 61 (Small RAW), JPEG, 7 (Fine), 8 (Normal), 3 (Large), 4 (Middle), 6 (Small).
i: Setting the ISO Speed for Still PhotosN Set the ISO speed (image sensor’s sensitivity to light) to suit the ambient light level. In Basic Zone modes, the ISO speed is set automatically. Regarding the ISO speed during movie shooting, see pages 200 and 202. 1 Press the button (9). the ISO speed. 2 Set While looking at the LCD panel or in the viewfinder, turn the <6> or <5> dial. ISO speed can be set within ISO 100 - ISO 16000 in 1/3-stop increments. “A” indicates ISO Auto.
i: Setting the ISO Speed for Still PhotosN As “H” (equivalent to ISO 25600) is an expanded ISO speed setting, noise (dots of light, banding, etc.) and irregular colors will be more noticeable, and the resolution will be lower compared with the standard setting. If [z3: Highlight tone priority] is set to [Enable], ISO 100/125/160 and “H” (equivalent to ISO 25600) cannot be selected (p.147). Shooting in high temperatures may result in images that look grainier.
A Selecting a Picture StyleN By selecting a Picture Style, you can obtain image characteristics matching your photographic expression or the subject. In Basic Zone modes, [D] (Auto) is set automatically. (In modes, [P] (Standard) is set.) 1 Select [Picture Style]. Under the [z3] tab, select [Picture Style], then press <0>. a Picture Style. 2 Select Select a Picture Style, then press <0>. The Picture Style will be set.
A Selecting a Picture StyleN R Landscape For vivid blues and greens, and very sharp and crisp images. Effective for impressive landscapes. u Fine Detail Suited for detailed outline and fine texture description of the subject. The colors will be slightly vivid. S Neutral This Picture Style is for users who prefer to process images with their computer. For natural colors and subdued images with modest brightness and color saturation. U Faithful Suited for processing the image with a computer.
3 Setting the White BalanceN White balance (WB) is for making the white areas look white. Normally, the Auto [Q] (Ambience priority) or [Qw] (White priority) setting will obtain the correct white balance. If natural-looking colors cannot be obtained with Auto, you can select the white balance to match the light source or set it manually by shooting a white object. In Basic Zone modes, [Q] (Ambience priority) is set automatically. (In the
mode, [Qw] (White priority) is set.) 1 Select [White balance].
3 Setting the White BalanceN White Balance To the human eye, a white object looks white regardless of the type of lighting. With a digital camera, the white for color correction basis is decided depending on the color temperature of the illumination, and then the color is adjusted with software to make the white areas look white. With this function, pictures with natural color tones can be taken.
3 Setting the White BalanceN Cautions for Setting [Qw] (White priority) The warm color cast of subjects may fade. When multiple light sources are included on the screen, the warm color cast of the picture may not be lessened. When using flash, the color tone will be the same as [Q] (Ambience priority).
3 Auto Correction of Brightness and ContrastN If the image comes out dark or the contrast is low, the brightness and contrast can be corrected automatically. This function is called Auto Lighting Optimizer. The default setting is [Standard]. With JPEG images, the correction is applied when the image is captured. In Basic Zone modes, [Standard] is set automatically. 1 Select [Auto Lighting Optimizer]. Under the [z2] tab, select [Auto Lighting Optimizer], then press <0>. the setting.
3 Setting Noise ReductionN High ISO Speed Noise Reduction This function reduces the noise generated in the image. Although noise reduction is applied at all ISO speeds, it is particularly effective at high ISO speeds. When shooting at low ISO speeds, the noise in the darker parts of the image (shadow areas) can further be reduced. 1 Select [High ISO speed NR]. Under the [z3] tab, select [High ISO speed NR], then press <0>. the level. 2 Set Select the desired noise reduction level, then press <0>.
3 Setting Noise ReductionN Cautions for Setting Multi Shot Noise Reduction If there is significant misalignment in the image due to camera shake, the noise reduction effect may become smaller. If you are handholding the camera, keep it steady to prevent camera shake. Using a tripod is recommended. If you shoot a moving subject, the moving subject may leave afterimages. The image alignment may not function properly with repetitive patterns (lattice, stripes, etc.) or flat, single-tone images.
3 Setting Noise ReductionN Long Exposure Noise Reduction Noise reduction is possible with images exposed for 1 sec. or longer. 1 Select [Long exp. noise reduction]. Under the [z3] tab, select [Long exp. noise reduction], then press <0>. the desired setting. 2 Set Select the desired setting, then press <0>. Auto For exposures of 1 sec. or longer, noise reduction is performed automatically if noise typical of long exposures is detected. This [Auto] setting is effective in most cases.
3 Setting Noise ReductionN With [Auto] and [Enable], the noise reduction process after the picture is taken may take the same amount of time as that for the exposure. You cannot take another picture until the noise reduction process is completed. Images taken at ISO 1600 or higher may look grainier with the [Enable] setting than with the [Disable] or [Auto] setting.
3 Highlight Tone PriorityN You can reduce overexposed, clipped highlights. 1 Select [Highlight tone priority]. Under the [z3] tab, select [Highlight tone priority], then press <0>. [Enable]. 2 Select Highlight details are improved. The dynamic range is expanded from the standard 18% gray to bright highlights. The gradation between the grays and highlights becomes smoother. the picture. 3 Take The image will be recorded with highlight tone priority applied.
3 Correction of Lens Peripheral Illumination and AberrationsN Peripheral light fall-off is a phenomenon that makes the image corners look darker due to the lens characteristics. Color fringing along subject outlines is called chromatic aberration. And image distortion due to lens characteristics is called distortion. These lens aberrations and light falloff can be corrected.
3 Correction of Lens Peripheral Illumination and AberrationsN Chromatic Aberration Correction 1 Select the setting. Check that [Correction data available] is displayed for the attached lens. Select [Chromatic aberration], then press <0>. Select [Enable], then press <0>. the picture. 2 Take The image will be recorded with the chromatic aberration corrected. Distortion Correction 1 Select the setting. Check that [Correction data available] is displayed for the attached lens.
3 Correction of Lens Peripheral Illumination and AberrationsN When distortion correction is enabled, the camera records an image range narrower than the one seen through the viewfinder. (Image periphery will be slightly trimmed and resolution slightly lowered.) Distortion correction will be reflected in the captured image, but not in the viewfinder or Live View image during shooting. If you set [Distortion correction] to [Enable], the maximum burst during continuous shooting will decrease.
3 Correction of Lens Peripheral Illumination and AberrationsN Cautions for Lens Correction Peripheral illumination correction, chromatic aberration correction, and distortion correction cannot be applied to JPEG images already taken. When using a non-Canon lens, setting the corrections to [Disable] is recommended, even if [Correction data available] is displayed.
3 Reducing FlickerN If you shoot an image with a fast shutter speed under a light source such as fluorescent light, the blinking of the light source causes flicker and the image may be vertically unevenly exposed. If continuous shooting is used under these conditions, uneven exposures or colors across the images may result.
3 Reducing FlickerN If the subject is against a dark background or if there is a bright light in the image, flicker may not be properly detected. Under certain special types of lighting, the camera may not be able to reduce the effects of the flicker even when is displayed in the viewfinder. Depending on the light source, flicker may not be detected properly. If you recompose a shot, may appear and disappear intermittently.
MEMO 154
5 Advanced Operations In Creative Zone modes, you can change various settings of the camera as you desire to obtain a wide variety of shooting results, by selecting the shutter speed and/or aperture, adjusting the exposure as you prefer, etc. The O icon at the upper right of the page title indicates that the function is available only in Creative Zone modes (d/ s/f/a/F).
d: Program AE The camera automatically sets the shutter speed and aperture to suit the subject’s brightness. This is called Program AE. * stands for Program. * AE stands for Auto Exposure. 1 Set the Mode Dial to . on the subject. 2 Focus Look through the viewfinder and aim the AF point over the subject. Then press the shutter button halfway. When focus is achieved, the focus indicator on the viewfinder’s bottom right will light up (when in One-Shot AF mode).
d: Program AE If the “30"” shutter speed and the lowest f/number blink, it indicates underexposure. Increase the ISO speed or use flash. If the “8000” shutter speed and the highest f/number blink, it indicates overexposure. Lower the ISO speed or use an ND filter (sold separately) to reduce the amount of light entering the lens. Differences Between and Modes In the mode, many functions, such as the AF operation and metering mode, are set automatically to prevent spoiled shots.
s: Shutter-Priority AE In this mode, you set the shutter speed and the camera automatically sets the aperture to obtain the standard exposure matching the brightness of the subject. This is called shutter-priority AE. A faster shutter speed can freeze the action of a moving subject. A slower shutter speed can create a blurred effect, giving the impression of motion. * stands for Time value. Blurred motion (Slow shutter speed: 1/30 sec.) 1 Frozen motion (Fast shutter speed: 1/2000 sec.
s: Shutter-Priority AE If the lowest f/number blinks, it indicates underexposure. Turn the <6> dial to set a slower shutter speed until the aperture stops blinking or set a higher ISO speed. If the highest f/number blinks, it indicates overexposure. Turn the <6> dial to set a faster shutter speed until the aperture stops blinking or set a lower ISO speed. Shutter Speed Display The shutter speeds from “8000” to “4” indicate the denominator of the fractional shutter speed.
f: Aperture-Priority AE In this mode, you set the desired aperture and the camera sets the shutter speed automatically to obtain the standard exposure matching the subject brightness. This is called aperture-priority AE. A higher f/number (smaller aperture hole) will make more of the foreground and background fall within acceptable focus. On the other hand, a lower f/number (larger aperture hole) will make less of the foreground and background fall within acceptable focus.
f: Aperture-Priority AE If the “30"” shutter speed blinks, it indicates underexposure. Turn the <6> dial to set a faster aperture (lower f/number) until the shutter speed blinking stops or set a higher ISO speed. If the “8000” shutter speed blinks, it indicates overexposure. Turn the <6> dial to set a slower aperture (higher f/number) until the shutter speed blinking stops or set a lower ISO speed. Aperture Value Display The higher the f/number, the smaller the aperture opening will be.
a: Manual Exposure In this mode, you set both the shutter speed and aperture as desired. To determine the exposure, refer to the exposure level indicator in the viewfinder or use a commercially-available exposure meter. This method is called manual exposure. * stands for Manual. 1 Set the Mode Dial to . 2 Set the ISO speed (p.135). the shutter speed and aperture. 3 Set To set the shutter speed, turn the <6> dial. To set the aperture, turn the <5> dial.
a: Manual Exposure Exposure Compensation with ISO Auto If the ISO speed is set to A (AUTO) for manual exposure shooting, you can set exposure compensation (p.166) as follows: • [z2: Expo.comp./AEB] • Under [8C.Fn III-4: Custom Controls] with [s: Expo comp (hold btn, turnS)]. • Quick Control (p.50) If ISO Auto is set, the ISO speed setting will change to suit the shutter speed and aperture in order to obtain a standard exposure. Therefore, you may not obtain the desired exposure effect.
q Selecting the Metering ModeN You can select one of four methods to measure the subject brightness. In Basic Zone modes, evaluative metering is set automatically. (In the <8: x> and modes, center-weighted average metering is set.) 1 Press the button (9). the metering mode. 2 Select While looking at the LCD panel, turn the <6> or <5> dial.
q Selecting the Metering ModeN e Center-weighted average metering The metering is averaged for the entire scene with the viewfinder center weighted more heavily. With q (Evaluative metering), the exposure setting will be locked when you press the shutter button halfway and focus is achieved. In the w (Partial metering), r (Spot metering), and e (Center-weighted average metering) modes, the exposure is set at the moment the picture is taken. (Pressing the shutter button halfway does not lock the exposure.
O Setting Exposure CompensationN Exposure compensation can brighten (increased exposure) or darken (decreased exposure) the standard exposure set by the camera. Exposure compensation can be set in the , , and shooting modes. Although you can set the exposure compensation up to ±5 stops* in 1/3-stop increments, the exposure compensation indicator in the viewfinder and on the LCD panel can only display the setting up to ±3 stops.
Auto Exposure Bracketing (AEB)N By changing the shutter speed or aperture automatically, the camera brackets the exposure up to ±3 stops in 1/3-stop increments for three successive shots. This is called AEB. * AEB stands for Auto Exposure Bracketing. 1 Select [Expo.comp./AEB]. Under the [z2] tab, select [Expo.comp./AEB], then press <0>. the AEB range. 2 Set Turn the <6> dial to set the AEB AEB range range. Press the keys to set the exposure compensation amount. Press <0> to set it.
Auto Exposure Bracketing (AEB)N During AEB, in the viewfinder and AEB range will blink. If the drive mode is set to or , press the shutter button three times for each shot. When , , or is set and you hold down the shutter button completely, the three bracketed shots will be taken continuously and the camera will automatically stop shooting. When or is set, the three bracketed shots will be taken continuously after a 10-sec. or 2-sec. delay.
A AE LockN You can lock the exposure when the area of focus is to be different from the exposure metering area or when you want to take multiple shots at the same exposure setting. Press the button to lock the exposure, then recompose and take the picture. This is called AE lock. It is effective for shooting backlit subjects, etc. 1 Focus on the subject. Press the shutter button halfway. The exposure setting will be displayed. the button (0).
D Using the Built-in Flash In Creative Zone modes, just press the button to raise the built-in flash for flash photography. Before shooting, check that [D] is displayed in the viewfinder. After shooting, push the built-in flash back down with your fingers until it clicks into place. In Basic Zone modes, depending on the shooting mode, you can set the built-in flash with Quick Control (p.101). The table below shows the shutter speed and aperture settings that will be used with flash.
D Using the Built-in Flash Effective Range of Built-in Flash (Approx. in meters / feet) EF-S18-135mm f/3.5-5.6 IS USM ISO Speed (p.135) Wide Angle f/3.5 f/5.6 ISO 100 1 - 3.4 / 3.3 - 11.2 1 - 2.1 / 3.3 - 6.9 Telephoto ISO 400 1 - 6.9 / 3.3 - 22.6 1 - 4.3 / 3.3 - 14.1 ISO 1600 1.7 - 13.7 / 5.6 - 44.9 1.1 - 8.6 / 3.6 - 28.2 ISO 6400 3.4 - 27.4 / 11.2 - 89.9 2.1 - 17.1 / 6.9 - 56.
MEMO 172
6 Shooting with the LCD Monitor (Live View Shooting) You can shoot while viewing the image on the camera’s LCD monitor. This is called “Live View shooting”. Live View shooting is enabled by setting the Live View shooting/ Movie shooting switch to . If you handhold the camera and shoot while viewing the LCD monitor, camera shake may cause blurred images. Using a tripod is recommended. Remote Live View Shooting With EOS Utility (EOS software, p.
A Shooting with the LCD Monitor 1 Set the Live View shooting/Movie shooting switch to . the Live View image. 2 Display Press the <0> button. The Live View image will appear on the LCD monitor. The Live View image will be displayed in the brightness level closely matching that of the actual image to be captured. on the subject. 3 Focus When you press the shutter button halfway, the camera will focus with the current AF method (p.180).
A Shooting with the LCD Monitor Enabling Live View Shooting Set [z5: Live View shoot.] (the [z3] tab in Basic Zone modes) to [Enable]. Number of Possible Shots with Live View Shooting Temperature Room Temperature (23°C / 73°F) (Approx. number of shots) Low Temperatures (0°C / 32°F) No Flash 340 310 50% Flash Use 300 270 The figures above are based on a fully-charged Battery Pack LP-E6N and CIPA (Camera & Imaging Products Association) testing standards.
A Shooting with the LCD Monitor Information Display Each time you press the button, the information display will change.
A Shooting with the LCD Monitor The histogram can be displayed by pressing the button when [z5: Expo. simulation: Enable] is set. However, the histogram is not displayed while pressing the shutter button completely. You can display the electronic level by pressing the button (p.66). Note that if the AF method is set to [u+Tracking] or the camera is connected to a TV set with an HDMI cable, the electronic level cannot be displayed.
Selecting the AF OperationN You can select the AF operation characteristics to suit the shooting conditions or subject. In Basic Zone modes, the optimum AF operation is set automatically for the respective shooting mode. 1 Press the button. the AF operation. 2 Select Press the keys to select the desired AF operation, then press <0>. X: One-Shot AF K: Servo AF If focus cannot be achieved, the AF point will turn orange.
Selecting the AF OperationN Servo AF for Moving Subjects This AF operation is suited for moving subjects. While you hold down the shutter button halfway, the camera will keep focusing on the subject continuously. If the drive mode is set to high-speed continuous shooting, the maximum speed will be approx. 5.0 fps. The pictures will be taken with priority given to the continuous shooting speed. If the drive mode is set to low-speed continuous shooting, the maximum speed will be approx. 3.0 fps.
Focusing with AF (AF Method) Selecting the AF Method You can select an AF method to suit the shooting conditions and your subject. The following AF methods are provided: [u(face)+Tracking] (p.181), [FlexiZone - Multi] (p.183), and [FlexiZone - Single] (p.185). If you want to achieve precise focus, set the lens’s focus mode switch to , magnify the image, and focus manually (p.192). 1 Press the button. the AF method. 2 Select Turn the <6> dial to select the AF method, then press <0>.
Focusing with AF (AF Method) u(face)+Tracking:c The camera detects and focuses on human faces. If a face moves, the AF point
also moves to track the face. 1 Display the Live View image. Press the <0> button. The Live View image will appear on the LCD monitor. the AF point. 2 Check When a face is detected, the area Area frame frame and the
frame will appear on the face for focusing. If multiple faces are detected, will be displayed.
Focusing with AF (AF Method) Focusing on a subject other than a human face Press <0> or and the AF frame will appear at the screen’s center. Then use <9> to move the AF frame over the desired subject. Once the AF frame achieves focus, it will track the subject even if the subject moves or if you change the composition. If the subject’s face is significantly out of focus, face detection will not be possible. Adjust the focus manually (p.
Focusing with AF (AF Method) FlexiZone - Multi: o You can use up to 35 AF points for wide-area focusing (automatic selection). This wide area can also be divided into 9 zones for focusing (zone selection). 1 Display the Live View image. Press the <0> button. The Live View image will appear on the LCD monitor. Area frame the AF point.O 2 Select Pressing <0> or the button will toggle between automatic selection and zone selection. In Basic Zone modes, automatic selection is set automatically.
Focusing with AF (AF Method) on the subject. 3 Focus Aim the AF point over the subject and press the shutter button halfway. When focus is achieved, the AF point will turn green and the beeper will sound. If focus is not achieved, the area frame will turn orange. the picture. 4 Take Check the focus and exposure, then press the shutter button completely to take the picture (p.174).
Focusing with AF (AF Method) FlexiZone - Single: d The camera focuses with a single AF point. This is effective when you want to focus on a particular subject. 1 AF point Display the Live View image. Press the <0> button. The Live View image will appear on the LCD monitor. The AF point < > will appear. During movie shooting, if [Movie Servo AF] is set to [Enable], the AF point will be displayed in a larger size. the AF point. 2 Move Use <9> to move the AF point to where you want to focus.
Focusing with AF (AF Method) the picture. 4 Take Check the focus and exposure, then press the shutter button completely to take the picture (p.174).
Focusing with AF (AF Method) Notes for AF AF Operation Even when focus is achieved, pressing the shutter button halfway will focus again. The image brightness may change during and after the AF operation. Depending on the subject or shooting conditions, etc., focusing may take longer or the continuous shooting speed may become slower. If the light source changes while the Live View image is displayed, the screen may flicker and focusing may be difficult.
Focusing with AF (AF Method) Shooting Conditions that Make Focusing Difficult Low-contrast subjects such as the blue sky, solid-color flat surfaces or when highlight or shadow details are lost. Subjects in low light. Stripes and other patterns where there is contrast only in the horizontal direction. Subjects with repetitive patterns (Example: Skyscraper windows, computer keyboards, etc.). Fine lines and subject outlines. Under a light source whose brightness, color, or pattern keeps changing.
Focusing with AF (AF Method) If focus is not achieved with the shooting conditions listed on the preceding page, set the lens’s focus mode switch to and focus manually. Depending on the lens used, focusing may take longer or correct focus may not be achieved. For details, refer to the Canon Web site. If you shoot a peripheral subject and it is slightly out of focus, aim the center AF point or zone over the subject to focus, focus again and then take the picture.
x Shooting with the Touch Shutter Just by tapping on the LCD monitor screen, you can focus and take the picture automatically. This works in all shooting modes. 1 Display the Live View image. Press the <0> button. The Live View image will appear on the LCD monitor. the touch shutter. 2 Enable Tap [y] on the screen’s bottom left. Each time you tap on the icon, it will toggle between [y] and [x]. [x] (Touch shutter: Enable) You can tap on the spot to focus and shoot.
x Shooting with the Touch Shutter Even if you set the drive mode to or , the camera will still shoot in single shooting mode. When you tap on the screen, focusing will be performed with One-Shot AF regardless of the [x: Touch Shutter] or [AF operation] settings. The touch shutter does not work with the magnified view. If the Fish-eye effect Creative filter is set, the camera will focus using the AF point at the center of the screen regardless of the point you tap on.
MF: Focusing Manually You can magnify the image and focus precisely with manual focus. 1 Set the lens’s focus mode switch to . Turn the lens focusing ring to focus roughly. the magnifying frame. 2 Display Press the button. The magnifying frame will appear. You can also tap [1] on the screen to magnify the image. Magnifying frame the magnifying frame. 3 Move Use <9> to move the magnifying frame to the position where you want to focus. You can also tap it to move it.
MF: Focusing Manually manually. 5 Focus While looking at the magnified image, turn the lens focusing ring to focus. After achieving focus, press the button to return to the normal view. the picture. 6 Take Check the exposure, then press the shutter button completely to take the picture (p.174). In magnified view, the exposure is locked. (Shutter speed and aperture will be displayed in red.
General Live View Shooting Cautions Image Quality When you shoot at high ISO speeds, noise (such as dots of light and banding) may become noticeable. Shooting in high temperatures may cause noise and irregular colors in the image. If Live View shooting is used continuously for a prolonged period, the camera’s internal temperature may rise, and image quality may deteriorate. Always exit Live View shooting when you are not shooting.
General Live View Shooting Cautions Live View Image Under low- or bright-light conditions, the Live View image may not reflect the brightness of the captured image. Even if a low ISO speed is set, noise may be noticeable in the displayed Live View image under low light. However, when you shoot, the image recorded will have less noise. (The image quality of the Live View image is different from that of the recorded image.
MEMO 196
7 Shooting Movies Movie shooting is enabled by setting the Live View shooting/ Movie shooting switch to . For cards that can record movies, see page 5. If you handhold the camera and shoot movies, camera shake can cause blurred movies. Using a tripod is recommended in such cases. Full HD 1080 Full HD 1080 indicates compatibility with HighDefinition featuring 1080 vertical pixels (scanning lines).
k Shooting Movies Autoexposure Shooting Autoexposure control will take effect to suit the scene’s current brightness. the Mode Dial to a mode other 1 Set than and . the Live View shooting/Movie 2 Set shooting switch to . The reflex mirror will make a sound, then the image will appear on the LCD monitor. on the subject. 3 Focus Before shooting a movie, focus with AF or manual focus (p.180-189, 192). When you press the shutter button halfway, the camera will focus with the current AF method.
k Shooting Movies In Basic Zone modes, the shooting result will be the same as with . Also, the scene icon for the scene detected by the camera is displayed on the upper left. In the , , and shooting modes, the settings will be the same as when shooting in the mode. Settable menu functions differ between Basic Zone modes and Creative Zone modes. In Creative Zone modes, you can press the button (p.169) to lock the exposure (AE lock).
k Shooting Movies ISO Speed in Basic Zone Modes The ISO speed will be set automatically within ISO 100 - ISO 12800. ISO Speed in the d, s, f, and F Modes The ISO speed will be set automatically within ISO 100 - ISO 12800. In [Range for movies] under [z2: ISO speed settings], if you set [Maximum] to [H(25600)], the automatic setting range will be expanded to H (equivalent to ISO 25600).
k Shooting Movies Manual Exposure Shooting You can manually set the shutter speed, aperture, and ISO speed for movie shooting. Using manual exposure to shoot movies is for advanced users. 1 Set the Mode Dial to . the Live View shooting/Movie 2 Set shooting switch to . the ISO speed. 3 Set Press the button. The ISO speed setting screen will appear on the LCD monitor. Turn the <6> dial to set the ISO speed. For details on the ISO speed, see the next page.
k Shooting Movies ISO Speed During Manual Exposure Shooting With [Auto] (A), the ISO speed will be set automatically within ISO 100 - ISO 12800. In [Range for movies] under [z2: ISO speed settings], if you set [Maximum] to [H(25600)], the automatic setting range will be expanded to H (equivalent to ISO 25600). Even if you set [Minimum] to ISO 200 or higher and [Maximum] to ISO 3200 or lower, the range will be set within ISO 100 - ISO 6400 automatically.
k Shooting Movies Information Display Each time you press the button, the information display will change.
k Shooting Movies You can display the electronic level by pressing the button (p.66). Note that if the AF method is set to [u +Tracking] or the camera is connected to a TV set with an HDMI cable, the electronic level cannot be displayed. The electronic level, grid lines, or histogram cannot be displayed during movie shooting. (The display will disappear when you start shooting a movie.) When movie shooting starts, the movie shooting remaining time will change to the elapsed time.
k Shooting Movies Still Photo Shooting Still photo shooting is not possible during movie shooting. To shoot still photos, stop shooting the movie and perform viewfinder shooting or Live View shooting. Cautions for Movie Shooting Do not point the camera toward an intense light source, such as the sun or an intense artificial light source. Doing so may damage the image sensor or the camera’s internal components.
k Shooting Movies Notes for Movie Shooting Movie-related settings are under the [z4] and [z5] tabs. (In Basic Zone modes, they are under the [z2] and [z3] tabs.) A movie file is recorded each time you shoot a movie. If the file size exceeds 4 GB, a new file will be created for every subsequent 4 GB (p.210). The movie image’s field of view is approx. 100% (with movie recording size set to [1920x1080]). You can also focus on the image by pressing the
button.
3 Setting the Movie Recording Size With [z4: Movie rec quality] (the [z2] tab in Basic Zone modes), you can set the movie recording format, movie recording size (image size, frame rate, and compression method), and other functions. MOV/MP4 You can select the movie’s recording format. D MOV The movie is recorded in the MOV format (file extension: “.MOV”). Convenient for editing with a computer. C MP4 The movie is recorded in the MP4 format (file extension: “.MP4”).
3 Setting the Movie Recording Size Movie Recording Size You can select the movie’s size, frame rate, and compression method. Image Size L 1920x1080 Full High-Definition (Full HD) recording quality. The aspect ratio is 16:9. w 1280x720 High-Definition (HD) recording quality. The aspect ratio is 16:9. Frame Rate (fps: frames per second) 6 29.97 fps/8 59.94 fps For areas where the TV system is NTSC (North America, Japan, South Korea, Mexico, etc.). 5 25.00 fps/7 50.
3 Setting the Movie Recording Size Compression Method Fixed at W if the recording format is MOV. For the MP4 format, X or Xv can be selected. • In MOV Format W ALL-I (For editing/I-only) Compresses one frame at a time for recording. Although the file size is larger than with IPB (Standard) and IPB (Light), the movie is better suited for editing. • In MP4 Format X IPB (Standard) Compresses multiple frames at a time efficiently for recording.
3 Setting the Movie Recording Size Total Movie Recording Time and File Size Per Minute In MOV Format Movie Recording Quality L 654 W (Approx.) Total Recording Time on Card 4 GB 16 GB 5 min. 23 min. 64 GB 1 hr. 33 min. 654 MB/min. In MP4 Format Movie Recording Quality File Size (Approx.) Total Recording Time on Card 4 GB File Size 16 GB 64 GB 35 min. 2 hr. 21 min. 431 MB/min. 1 hr. 10 min. 4 hr. 41 min. 216 MB/min. 87 X 8 min. L 654 X 17 min. 65 Xv 43 min. 2 hr. 53 min.
3 Setting the Movie Recording Size Movie Shooting Time Limit The maximum recording time of one movie clip is 29 min. 59 sec. If the movie shooting time reaches 29 min. 59 sec., the movie shooting will stop automatically. You can start shooting a movie again by pressing the <0> button. (The movie will be recorded as a new movie file.
General Movie Shooting Cautions Red Internal Temperature Warning Icon If the camera’s internal temperature increases due to prolonged movie shooting or under a high ambient temperature, a red icon will appear. The red icon indicates that movie shooting will soon be terminated automatically. If this happens, you will not be able to shoot again until the camera’s internal temperature decreases. Turn off the power and let the camera rest for a while.
General Movie Shooting Cautions Recording and Image Quality If you use a card with a slow writing speed, a five-level indicator may appear on the right of the screen during movie shooting. It indicates how much data has not yet been written to the card (remaining capacity of the internal buffer memory). The slower the card, the faster the indicator will climb upward. If the indicator becomes full, movie shooting Indicator will stop automatically.
MEMO 214
8 Image Playback This chapter explains basic procedures to play back images and movies. Images shot and saved with another device The camera may not be able to properly display images captured with a different camera, edited with a computer, or that have had their file names changed.
x Image Playback Single-Image Display 1 Play back the image. Press the button. The last image captured or played back will appear. an image. 2 Select To play back images starting with the last image captured, turn the <5> dial counterclockwise. To play back images starting with the first captured image, turn the dial clockwise. Each time you press the button, the information display will change.
x Image Playback the image playback. 3 Exit Press the button to exit the image playback and return to shooting-ready state. Shooting Information Display With the shooting information screen displayed (p.216), you can press the keys to change the shooting information displayed at the screen’s bottom as follows. For details, see pages 219-220.
B: Shooting Information Display The information displayed varies depending on the shooting mode and settings.
B: Shooting Information Display Shooting information display • Detailed information Exposure compensation amount Histogram (Brightness/RGB) Shooting date and time Aperture Shutter speed ISO speed Shooting mode Scroll bar Highlight tone priority Metering mode White balance File size Auto Lighting Optimizer White balance correction Picture Style/Settings Flash exposure compensation amount / Multi Shot Noise Reduction Image-recording quality AF Microadjustment * When you shoot in RAW+JPEG image qu
B: Shooting Information Display • Lens/Histogram information Histogram display (Brightness) Lens name Focal length Histogram display (RGB) • White balance information • Picture Style information 1 • Picture Style information 2 • Color space / Noise reduction information • Lens aberration correction information If you used GPS Receiver GP-E2 to record GPS information for the image, the “GPS information” screen will also appear.
B: Shooting Information Display Sample Movie Information Display Playback Aperture Shutter speed Movie shooting mode/ Time-lapse movie Creative filters Recording format Movie recording size Frame rate Movie file size Shooting time, Playback time Compression method * If manual exposure is used, the shutter speed, aperture, and ISO speed (when set manually) will be displayed. * The icon will be displayed for video snapshots. * The icon will be displayed for HDR movies.
x Searching for Images Quickly H Displaying Multiple Images on One Screen (Index Display) Search for images quickly with the index display showing 4, 9, 36, or 100 images on one screen. 1 Switch to the index display. During image playback, press the button. The 4-image index display will appear. The selected image is highlighted with an orange frame. Pressing the button will switch the display as follows: 9 images 9 36 images 9 100 images.
u/y Magnified View You can magnify a captured image by approx. 1.5x to 10x on the LCD monitor. 1 Magnify the image. Press the button during image playback. The image will be magnified. If you hold down the button, the image will be magnified until it reaches the maximum magnification. Press the button to reduce the magnification. If you hold down the button, the magnification will be reduced to the single-image display. Magnified area position around the image.
d Playing Back with the Touch Screen The LCD monitor is a touch-sensitive panel that you can touch with your fingers for various playback operations. First, press the button to play back images. Browsing Images Swipe with one finger. With single-image display, touch the LCD monitor with one finger. You can browse to the next or previous image by swiping your finger to the left or right. Swipe to the left to see the next (newer) image, or swipe to the right to see the previous (older) image.
d Playing Back with the Touch Screen Reducing Image (Index Display) Pinch two fingers. Touch the screen with two fingers spread apart, and pinch your fingers together on the screen. Each time you pinch your fingers, the single-image display will change to the index display. If you spread your fingers, the image display will change in the reverse order. When you select an image, the orange frame will appear. Tap on the image again to display it as a single image.
k Playing Back Movies 1 Play back the image. Press the button to display an image. a movie. 2 Select Turn the <5> dial to select the movie to be played back. In the single-image display, the icon displayed on the upper left of the screen indicates a movie. If the movie is a video snapshot, will be displayed. In the index display, perforations at the left edge of a thumbnail indicate a movie.
k Playing Back Movies Movie Playback Panel Operation Playback Description 7 Play Pressing <0> toggles between play and stop. 8 Slow motion Adjust the slow motion speed by pressing the keys. The slow motion speed is indicated on the upper right of the screen. 5 First frame Displays the movie’s first frame. 3 Previous frame Each time you press <0>, the previous frame is displayed. If you hold down <0>, it will rewind the movie.
k Playing Back Movies Playback with the Touch Screen Tap [7] on the center of the screen. The movie will start playing back. To display the movie playback panel, tap on the upper left of the screen. To pause the movie while it is playing back, tap on the screen. The movie playback panel will also appear.
L Erasing Images You can either select and erase unnecessary images one by one or erase them in one batch. Protected images will not be erased. Once an image is erased, it cannot be recovered. Make sure you no longer need the image before erasing it. To prevent important images from being erased accidentally, protect them. Erasing an image shot in RAW+JPEG will erase both the RAW and JPEG images. Erasing a Single Image 1 Play back the image to be erased. the button.
MEMO 230
9 Software Start Guide / Downloading Images to a Computer This chapter explains the following: Overview of the software for EOS DIGITAL cameras How to download and install the software on a computer How to download and view the Software Instruction Manuals (PDF files) How to download images from the camera to a computer 231
Software Start Guide Software Overview This section explains an overview of various software applications for EOS DIGITAL cameras. Internet connection is required to download and install the software. Download and installation are not possible in environments with no Internet connection. EOS Utility With the camera connected to a computer, EOS Utility enables you to transfer still photos and movies shot with the camera to the computer.
Software Start Guide Downloading and Installing the Software Do not connect the camera to your computer before you install the software. Otherwise, the software will not be installed properly. Even if a previous version of the software is installed on your computer, follow the procedure below to install the latest version. (The previous version will be overwritten.) 1 Download the software. Connect to the Internet from a computer and access the following Canon Web site. www.canon.
Downloading and Viewing the Software Instruction Manuals (PDF Files) Internet connection is required to download the Software Instruction Manuals (PDF files). Download is not possible in environments with no Internet connection. 1 Download the Software Instruction Manuals (PDF files). Connect to the Internet and access the following Canon Web site. www.canon.com/icpd Select your country or region of residence and download the Instruction Manuals. 2 View the Software Instruction Manuals (PDF files).
Downloading Images to a Computer You can use EOS software to download the images in the camera to a computer. There are two ways to do this. Downloading by Connecting the Camera to the Computer 1 Install the software (p.233). an interface cable to connect 2 Use the camera to the computer. Connect the cable to the camera’s digital terminal with the cable plug’s icon facing the front of the camera. Connect the plug to the computer’s USB terminal. EOS Utility to download the 3 Use images.
Downloading Images to a Computer Downloading Images with a Card Reader You can use a card reader to download images to a computer. Install the software (p.233). 1 the card into the card 2 Insert reader. Digital Photo Professional to 3 Use download the images. Refer to the Digital Photo Professional Instruction Manual. When downloading images from the camera to a computer with a card reader without using EOS software, copy the DCIM folder on the card to the computer.
Trademarks Adobe is a trademark of Adobe Systems Incorporated. Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. Macintosh and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries. SDXC logo is a trademark of SD-3C, LLC. HDMI, HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Use of genuine Canon accessories is recommended This product is designed to achieve excellent performance when used with genuine Canon accessories. Canon shall not be liable for any damage to this product and/or accidents such as fire, etc., caused by the malfunction of non-genuine Canon accessories (e.g., a leakage and/or explosion of a battery pack).
Digital Camera Model DS126591 Systems This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for class B digital devices, pursuant to Part 15 of the FCC Rules.
USA and Canada only: The Lithium ion/polymer battery that powers the product is recyclable. Please call 1-800-8-BATTERY for information on how to recycle this battery. For CA, USA only Included lithium battery contains Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate/ for details. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO LOCAL REGULATION.
Index Numerics 10- or 2-sec. self-timer ..................130 1280x720 (movie) .........................208 1920x1080 (movie) .......................208 45-point AF auto selection ............114 A A (Scene Intelligent Auto) ............72 Access lamp....................................32 Accessories.......................................3 AE lock..........................................169 AEB (Auto Exposure Bracketing)...167 AF AF area selection mode....114, 115 AF-assist beam.........................
Index O (Creative Zone) icon....................8 Creative Zone modes .....................25 Cross-type focusing ......................118 Custom Controls .............................51 D Date/time ........................................37 Daylight saving time........................38 Default settings ...............................62 Depth-of-field preview...........161, 174 Dials Main Dial ....................................45 Mode Dial ...................................45 Quick Control Dial .....
Index Index display .................................222 INFO. button .................176, 203, 216 Initializing the card (formatting).......58 IPB (Light) .....................................209 IPB (Standard) ..............................209 ISO speed .....................135, 200, 202 J JPEG.............................................132 K Kids .................................................84 L Landscape ......................................90 Language ........................................
Index M-RAW (Medium RAW)........133, 134 Multi function lock ...........................48 Multi Shot Noise Reduction ..........143 Multi-controller ................................47 N Night Portrait...................................86 Night scenes .............................86, 87 Noise reduction High ISO speed ........................143 Long exposures........................145 Nomenclature .................................20 Normal (image-recording quality) ......133, 134 NTSC ....................
Index v (Creative filters) ....................95 G (Grainy B/W).......................97 W (Soft focus) .........................97 X (Fish-eye effect)..................98 H (Toy camera effect) ............98 c (Miniature effect).................98 Z (Water painting effect) ........98 A (HDR art standard) ...........98 B (HDR art vivid) ..................99 C (HDR art bold) ..................99 D (HDR art embossed).........99 Shutter button .................................44 Shutter-priority AE..........
MEMO 246
EOS 80D (W) Wireless Function Basic Instruction Manual In Wireless Function Basic Instruction Manual, basic operation procedures for easy-to-use “Connect to a smartphone”, “Transfer images between cameras”, and “Save images to Connect Station” are explained.
Introduction What You Can Do Using the Wireless Functions This camera’s wireless functions let you perform a range of tasks wirelessly, from sending images to Web services and other cameras to controlling the camera remotely, simply by connecting to a Wi-Fi network or other device supporting this camera’s wireless functions.
Introduction (1) q Connect to a smartphone (p.W-19) Connect the camera to a smartphone or tablet wirelessly and use the dedicated application “Camera Connect” to operate the camera remotely or view images stored in the camera. In this manual and on the camera’s LCD monitor, “smartphone” refers to smartphones and tablets. (2) z Transfer images between cameras (p.W-39) Wirelessly connect this camera and other Canon cameras with built-in wireless functions and transfer images between them.
Introduction Easy Connection Using the NFC Function This camera supports NFC* which enables you to set up a connection between the camera and a smartphone or Connect Station (sold separately) easily. For details, see page W-16. * Near Field Communication Instruction Manual For how to use [Remote control (EOS Utility)], [Print from Wi-Fi printer], [View images on DLNA devices], and [Upload to Web service] and for more detailed procedures, refer to the “Wireless Function Instruction Manual” PDF file.
Contents Introduction W-2 What You Can Do Using the Wireless Functions ........................ W-2 Conventions Used in this Manual ................................................ W-6 Preparation and Basic Operation 1 W-7 Registering a Nickname............................................................... W-8 Basic Operation and Settings .................................................... W-11 NFC Function.............................................................................
Conventions Used in this Manual In this manual, the terms “wireless” and “wireless LAN” are used as general terms for Wi-Fi and Canon’s original wireless functions. The camera does not come with an interface cable. Icons in this Manual <6> : Indicates the Main Dial. <5> : Indicates the Quick Control Dial. : Indicates the direction to push the Multicontroller. <0> : Indicates the Setting button.
1 Preparation and Basic Operation This chapter describes how to register a nickname (for identification) necessary for using the camera’s wireless functions and the basic operations.
Registering a Nickname First, set the camera’s nickname (for identification). When the camera is connected to another device wirelessly, the nickname will be displayed on the device. Be sure to set a nickname as otherwise you cannot set the wireless functions. 1 Select [Wireless communication settings]. Under the [51] tab, select [Wireless communication settings], then press <0>. 2 Select [Nickname]. When this setting is selected for the first time, a screen to register a nickname is displayed.
Registering a Nickname a nickname. 3 Enter For instructions on entering characters, see the next page. Enter any characters between 1 to 10 characters in length. the setting. 4 Exit When you are finished, press the button. Select [OK] on the confirmation dialog and press <0> to return to the menu screen. Since the nickname is mandatory information, you cannot delete all the characters. By default, the camera name will be displayed for the nickname.
Registering a Nickname Virtual Keyboard Operation Changing the entry area Press the button to toggle between the top and bottom entry areas. Moving the cursor Press the keys in the top area to move the cursor. Entering text In the bottom area, press the or keys to select a character, then press <0> to enter it. You can check how many characters you have entered, and how many more can be entered, by referring to [*/*] on the upper right of the screen.
Basic Operation and Settings The basic operation for using the camera’s wireless functions is explained here. Follow the procedures below. 1 Select [Wireless communication settings]. Under the [51] tab, select [Wireless communication settings], then press <0>. 2 Select [Wi-Fi/NFC]. [Enable]. 3 Select When a nickname (for identification) is not registered, a registration screen is displayed. See page W-8 to register a nickname. [Wi-Fi function] is now selectable. 4 Select [Wi-Fi function].
Basic Operation and Settings the Wi-Fi function to 5 Select connect to. Press the or keys to select an item. When the connection settings are not registered, the setting screen is displayed. When the connection settings are already registered, the reconnection screen is displayed. When using the NFC function, see page W-16.
Basic Operation and Settings [Wi-Fi function] The following Wi-Fi functions are available: Transfer images between cameras Connect to smartphone Remote control (EOS Utility) Print from Wi-Fi printer View images on DLNA devices Upload to Web service [Send images to smartphone] While the camera is connected to a smartphone, use this function to send images stored in the camera to the smartphone. [Nickname] Register or change the nickname.
Basic Operation and Settings When multiple exposures, video snapshot, or time-lapse movie is set, you cannot select [51: Wireless communication settings]. Interface Cable Connection Cautions During a wireless LAN connection, you cannot use the camera by connecting it to Connect Station, a computer, a GPS receiver, or another device with a cable. Terminate the connection before connecting a cable.
Basic Operation and Settings Wireless Connection Status Wireless connection status can be checked on the camera’s LCD monitor and LCD panel.
NFC Function Using an NFC-enabled smartphone or Connect Station enables you to do the following: Touch a smartphone to the camera to easily connect them wirelessly (p.W-21). While playing back images on the camera, touch a smartphone to the camera to send a captured image to the smartphone (p.W-33). Hold the camera close to Connect Station (sold separately) to easily connect them wirelessly (p.W-48). When using the NFC function, follow the steps below to set the camera’s NFC setting.
NFC Function When establishing wireless communications using the NFC function, see the following pages. Connecting to a smartphone wirelessly: page W-21* Sending images to a smartphone: page W-33* Connecting to Connect Station: page W-48 * When connecting to a smartphone, see pages W-18 and W-20 as well. NFC Function Cautions This camera cannot be connected to other NFC-enabled cameras or printers using the NFC function.
Preparation for Smartphones To use [q] (Connect to smartphone), a smartphone on which iOS or Android is installed is necessary. In addition, the dedicated application Camera Connect (free of charge) must be installed on the smartphone. Camera Connect can be downloaded from the App Store or Google Play. For the operating system versions supported by Camera Connect, refer to the download site of Camera Connect.
2 Easy Connection to a Smartphone Connecting the camera to a smartphone enables you to do the following: • View images stored in the camera on a smartphone or save viewed images to a smartphone. • Operate the camera to take a picture or change camera settings using a smartphone. • Send images to a smartphone from the camera. This section explains how to connect the camera directly to a smartphone. Install Camera Connect on the smartphone before setting up a connection (p.W-18).
Connection Method When the smartphone is NFC-enabled: See page W-21. You can easily set up a connection using the NFC function. When the smartphone is not NFC-enabled: See page W-24. Set up a connection by selecting [Easy connection]. Smartphones labeled with the p mark are NFC-enabled. Some smartphones are not labeled with the p mark even if they are NFCenabled; if you do not know whether your smartphone is NFC-enabled, contact the manufacturer of the smartphone.
Connecting Automatically with the NFC Function Connect the camera and a smartphone using the NFC function. The operation flow for connecting via NFC is as follows. (1) Turn on the camera and smartphone. (2) Enable the NFC function on the camera and smartphone. (3) Touch the smartphone to the camera so that they come into contact with each other. For the camera’s NFC setting, see page W-16.
Connecting Automatically with the NFC Function to the camera. 3 Connect When a connection is established, The device name set on Camera Connect the screen on the left will appear on the camera’s LCD monitor. When connecting to the same smartphone, this screen will not appear again. Select [OK] and press <0>. After a message is displayed, the [qWi-Fi on] screen will appear. The main window of Camera Connect will be displayed on the smartphone. To return to the menu, press the button.
Connecting Automatically with the NFC Function If necessary, also read “NFC Function Cautions” (p.W-17). When touching the smartphone to the camera, be careful not to drop the camera or smartphone. Do not touch the smartphone to the camera with too much force. Doing so can scratch the camera or smartphone. Just holding the smartphone close to the mark may not establish a connection. Be sure to touch the mark with the smartphone so that they come into contact with each other.
Connecting with Easy Connection The camera and a smartphone can be directly connected wirelessly. No access point is necessary, so you can establish a wireless connection easily. To establish connection, operations on the smartphone are required. For details, refer to the smartphone’s instruction manual. Operation on the Camera-1 1 Select [Wireless communication settings]. Under the [51] tab, select [Wireless communication settings], then press <0>. [Wi-Fi function].
Connecting with Easy Connection Operation on the Smartphone Smartphone’s screen (sample) the smartphone and 5 Operate connect it to the camera. Activate the smartphone’s Wi-Fi function, then select the SSID (network name) displayed on the camera’s LCD monitor. For the password, enter the encryption key displayed on the camera’s LCD monitor. Camera’s screen SSID (network name) Encryption key (password) When connecting by selecting [Easy connection], “_Canon0A” is displayed at the end of the SSID.
Connecting with Easy Connection Camera Connect on the 6 Start smartphone. When the [Waiting to connect] screen is displayed on the camera’s LCD monitor, start Camera Connect on the smartphone. the camera to connect to 7 Select on the smartphone. Select and touch the camera to connect to from [Cameras] on Camera Connect.
Connecting with Easy Connection Operation on the Camera-2 to the camera. 8 Connect When a connection is established, The device name set on Camera Connect the screen on the left will appear on the camera’s LCD monitor. Select [OK] and press <0>. After a message is displayed, the [qWi-Fi on] screen will appear. The main window of Camera Connect will be displayed on the smartphone. To return to the menu, press the button. The settings for connecting to a smartphone are now complete.
Operating the Camera Using a Smartphone You can use a smartphone with Camera Connect installed to view images stored in the camera and shoot remotely. Camera Connect Main Window The main functions of Camera Connect are described below. Touch the screen to learn the operation procedures. [Images on camera] Images stored in the camera can be viewed. Images stored in the camera can be saved on a smartphone. Operations such as deletion can be performed on images stored in the camera.
Operating the Camera Using a Smartphone Terminating the Connection To terminate the connection, perform either of the following operations. On the smartphone’s Camera Connect screen, tap [t]. On the camera’s [qWi-Fi on] screen, select [Disconnect,exit]. If the [qWi-Fi on] screen is not displayed, select the [51] tab 9 [Wireless communication settings] 9 [Wi-Fi function]. Select [Disconnect,exit], then select [OK] on the confirmation dialog to terminate the connection.
Operating the Camera Using a Smartphone When the wireless connection is terminated while recording a movie with remote shooting, the camera responds as follows: • When the Live View shooting/Movie shooting switch is set to , movie shooting continues. • When the Live View shooting/Movie shooting switch is set to , movie shooting stops. When the Live View shooting/Movie shooting switch is set to and the movie mode is set by operating Camera Connect, you cannot shoot by operating the camera.
Reconnecting The camera can reconnect to a Wi-Fi function for which connection settings have been registered. 1 Select [Wi-Fi function]. Set [Wi-Fi/NFC] to [Enable], then select [Wi-Fi function]. the Wi-Fi function to 2 Select connect to. Press the or keys to select an item, then press <0>. [Connect]. 3 Select When settings for multiple connection destinations are registered, select [Choose set.], select the connection destination, then connect to the destination.
Reconnecting 4 Operate the target device. Activate the smartphone’s Wi-Fi function, then start Camera Connect. If the smartphone’s connection destination has been changed, restore the setting to connect to the camera or the same access point as the camera. If you do not know the SSID of the destination when reconnecting, select [Review/change settings] 9 [Confirm set.] in the screen for step 3 to check it.
Sending Images to a Smartphone Operate the camera to send images to a smartphone. The following three send methods are available: (1) While playing back an image, connect to a smartphone using the NFC function (p.W-33). (2) During a wireless connection, select [Send images to smartphone] from the camera menu (p.W-34). (3) During a wireless connection, send images from the Quick Control screen during playback (p.W-35).
Sending Images to a Smartphone a smartphone to the camera. 3 Touch Touch the p mark on the smartphone to that on the camera. When a message indicating the connection is displayed on the camera’s LCD monitor, move the smartphone away. the images to send. 4 Select Select and send image(s). For information on how to send images, see page W-36. When the index display is selected in step 2, the multiple image selection screen will appear. See step 3 on page W-37.
Sending Images to a Smartphone (3) Quick Control During Playback While the camera is wirelessly connected to a smartphone, send images from the Quick Control screen during playback. the camera to a 1 Connect smartphone wirelessly. back the image and press 2 Play the button. 3 Select [q]. the images to send. 4 Select Select and send image(s). For information on how to send images, see page W-36.
Sending Images to a Smartphone Sending Images Individually Select and send images individually. 1 Select an image to send. Turn the <5> dial to select an image to send, then press <0>. By pressing the button, you can switch to the index display and select an image. [Send img shown]. 2 Select To select a size at which to send the image, select [Resize image] and press <0>. Select [Send img shown] and press <0> to send the image displayed.
Sending Images to a Smartphone the images to send. 3 Select Turn the <5> dial to select an image to send, then add [X]. Press <0> to add or remove [X]. By pressing the button, you can select images from a three-image display. After selecting the images to send, press the button. [Resize image]. 4 Select Set it if necessary. On the displayed screen, select an image size, then press <0>. [Send]. 5 Select The selected images will be sent.
Sending Images to a Smartphone Ending Image Transfer To end the image transfer, press the button on the image transfer screen. If you have established the connection with the NFC function while playing back an image, the connection termination screen will appear. Select [OK] to terminate the connection. If you have sent images from the menu or Quick Control, the previous screen will reappear. The connection will not be terminated. If necessary, also read “NFC Function Cautions” (p.W-17).
3 Easy Connection Between Cameras This section explains how to connect this camera and other Canon cameras with built-in wireless functions easily. Wireless connection is possible for Canon cameras with built-in wireless functions released in and after 2012 supporting image transfer between cameras. Note that the camera cannot be connected to Canon camcorders, even if they have built-in wireless functions.
Connecting to a Camera Register the target camera to connect to wirelessly. The camera can be connected to only one camera at a time. 1 Select [Wireless communication settings]. Under the [51] tab, select [Wireless communication settings], then press <0>. [Wi-Fi function]. 2 Select Set [Wi-Fi/NFC] to [Enable], then select [Wi-Fi function]. Select [z] (Transfer imgs 3 between cameras). the connection on the target 4 Start camera.
Connecting to a Camera the images to send. 5 Select Select images on the camera sending the images (p.W-42). Do not operate the camera receiving the images. The settings for connecting to a camera are now complete. For operations after setting up a connection, see page W-42. Note that GPS information is not displayed on the camera’s playback screen even if GPS information is appended to the received image. Shooting locations can be viewed on a virtual map, using Map Utility (EOS software).
Sending Images to a Camera Sending Images Individually Select and send images individually. 1 Select an image to send. Turn the <5> dial to select an image to send, then press <0>. By pressing the button, you can switch to the index display and select an image. [Send img shown]. 2 Select To select a size at which to send the image, select [Resize image] and press <0>. Select [Send img shown] and press <0> to send the image displayed.
Sending Images to a Camera Sending Multiple Images Select multiple images and send them at once. 1 Press <0>. [Send selected]. 2 Select To select a size at which to send the images, select [Resize image] and press <0>. the images to send. 3 Select Turn the <5> dial to select an image to send, then add [X]. Press <0> to add or remove [X]. By pressing the button, you can select images from a three-image display. After selecting the images to send, press the button. [Resize image].
Sending Images to a Camera [Send]. 5 Select The selected images will be sent. When the transfer is complete, the screen for step 1 will reappear. To send other images, repeat steps 1 to 5. the connection. 6 Terminate Press the button to display the confirmation dialog. Select [OK], then press <0> to terminate the connection. The [Wi-Fi function] screen will reappear. While connected, a picture cannot be taken even if the camera’s shutter button is pressed.
Reconnecting The camera can reconnect to a Wi-Fi function for which connection settings have been registered. 1 Select [Wi-Fi function]. Set [Wi-Fi/NFC] to [Enable], then select [Wi-Fi function]. the Wi-Fi function to 2 Select connect to. Press the or keys to select an item, then press <0>. [Connect]. 3 Select When settings for multiple connection destinations are registered, select [Choose set.], select the connection destination, then connect to the destination.
Reconnecting 4 Operate the target device. Perform the reconnection procedure on the target camera as well. By default, settings are named after the nickname of the camera that was connected to.
4 Easy Connection to Connect Station Connect Station (sold separately) is a device that allows you to import captured still photos and movies for viewing on your TV set, smartphone, etc., or sharing them over a network. You can easily save still photos and movies to Connect Station by holding this camera close to Connect Station.
Saving Images This section explains how to connect the camera and Connect Station (sold separately) wirelessly. To save images in other ways, refer to the Connect Station Instruction Manual. Set up the camera to allow use of its NFC function in advance (p.W-16). the NFC function on the 1 Enable camera (p.W-16). the camera close to Connect 2 Hold Station. NFC connect point Turn on the camera and Connect Station, then hold the camera’s p mark close to the Connect Station’s NFC connect point.
Saving Images If necessary, also read “NFC Function Cautions” (p.W-17). While saving images, a picture cannot be taken even if the camera’s shutter button is pressed. Do not drop the camera on Connect Station or touch the camera to it with too much force. Doing so may damage Connect Station's internal hard disk. If the camera is not recognized right away, try holding it close to Connect Station and slowly moving it or rotating it horizontally.
Wi-Fi (Wireless LAN) Precautions 9Countries and Regions Permitting Wireless LAN Use Use of wireless LAN is restricted in some countries and regions, and illegal use may be punishable under national or local regulations. To avoid violating wireless LAN regulations, visit the Canon Web site to check where use is allowed. Note that Canon cannot be held liable for any problems arising from wireless LAN use in other countries and regions.
Hereby, Canon Inc., declares that this DS126591 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Please contact the following address for the original Declaration of Conformity: CANON EUROPA N.V. Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands CANON INC.
Index A Android ...................................... W-18 C Cable ......................................... W-14 Camera Connect..............W-18, W-28 Connect Station ......................... W-47 Connecting to a smartphone...... W-19 E Eye-Fi Card................................ W-14 I iOS............................................. W-18 K Keyboard ................................... W-10 N NFC ........... W-16, W-20, W-21, W-48 Sending images..................... W-33 Nickname...................
MEMO W-53
MEMO W-54
MEMO W-55
MEMO W-56
MEMO W-57
MEMO W-58
The descriptions in this Instruction Manual are current as of February 2016. For information on the compatibility with any products introduced after this date, contact any Canon Service Center. For the latest version Instruction Manual, refer to the Canon Web site. CPH-E174-001 © CANON INC.