TS9500 series Online Manual English
Contents Using Online Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Symbols Used in This Document. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Touch-enabled Device Users (Windows). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Trademarks and Licenses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Basic Operation. . . . . . .
Placing Multi-purpose Tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Cautions When Printing with Multi-purpose Tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Placing a Printable Disc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 Before Placing a Printable Disc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 Cleaning Paper Feed Rollers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 Cleaning Inside the Printer (Bottom Plate Cleaning). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LAN settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219 Other device settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 Language selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 Firmware update. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disc Label Printing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279 Copying Label Side of Disc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280 Printing Photo from Memory Card onto Disc Label. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283 Paper Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cannot Find Printer on Check Printer Settings Screen During Wi-Fi Setup (Windows)-Checking Wireless Router Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328 Cannot Find Printer on Check Printer Settings Screen During Wired LAN Setup (Windows)Checking LAN Cable and Router. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scanning Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382 Scanner Does Not Work. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383 Scanner Driver Does Not Start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384 Mechanical Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2110. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 426 4103. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429 5011. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430 5012. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using Online Manual Operating Environment Symbols Used in This Document Touch-enabled Device Users (Windows) Printing Online Manual Trademarks and Licenses Screenshots in This Manual 10
Symbols Used in This Document Warning Instructions that, if ignored, could result in death, serious personal injury, or property damage caused by incorrect operation of the equipment. These must be observed for safe operation. Caution Instructions that, if ignored, could result in personal injury or property damage caused by incorrect operation of the equipment. These must be observed for safe operation.
Touch-enabled Device Users (Windows) For touch actions, you need to replace "right-click" in this document with the action set on the operating system. For example, if the action is set to "press and hold" on your operating system, replace "right-click" with "press and hold.
Trademarks and Licenses • Microsoft is a registered trademark of Microsoft Corporation. • Windows is a trademark or registered trademark of Microsoft Corporation in the U.S. and/or other countries. • Windows Vista is a trademark or registered trademark of Microsoft Corporation in the U.S. and/or other countries. • Internet Explorer is a trademark or registered trademark of Microsoft Corporation in the U.S. and/or other countries.
Apache License Version 2.0, January 2004 http://www.apache.org/licenses/ TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION 1. Definitions. "License" shall mean the terms and conditions for use, reproduction, and distribution as defined by Sections 1 through 9 of this document. "Licensor" shall mean the copyright owner or entity authorized by the copyright owner that is granting the License.
2. Grant of Copyright License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable copyright license to reproduce, prepare Derivative Works of, publicly display, publicly perform, sublicense, and distribute the Work and such Derivative Works in Source or Object form. 3. Grant of Patent License.
7. Disclaimer of Warranty. Unless required by applicable law or agreed to in writing, Licensor provides the Work (and each Contributor provides its Contributions) on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied, including, without limitation, any warranties or conditions of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or FITNESS FOR A PARTICULAR PURPOSE.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
Use is subject to license terms below. This distribution may include materials developed by third parties. Sun, Sun Microsystems, the Sun logo and Solaris are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries.
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ---- Part 6: Cisco/BUPTNIC copyright notice (BSD) ----Copyright (c) 2004, Cisco, Inc and Information Network Center of Beijing University of Posts and Telecommunications. All rights reserved.
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ---- Part 8: Apple Inc. copyright notice (BSD) ----Copyright (c) 2007 Apple Inc.
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. LEADTOOLS Copyright (C) 1991-2009 LEAD Technologies, Inc.
MIT License Copyright (c) 1998, 1999, 2000 Thai Open Source Software Center Ltd Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
CONCERNING THE MERCHANTABILITY OF THIS SOFTWARE OR ITS FITNESS FOR ANY PARTICULAR PURPOSE. (1) Red Hat Incorporated Copyright (c) 1994-2009 Red Hat, Inc. All rights reserved. This copyrighted material is made available to anyone wishing to use, modify, copy, or redistribute it subject to the terms and conditions of the BSD License.
The FreeType Project is distributed in several archive packages; some of them may contain, in addition to the FreeType font engine, various tools and contributions which rely on, or relate to, the FreeType Project. This license applies to all files found in such packages, and which do not fall under their own explicit license. The license affects thus the FreeType font engine, the test programs, documentation and makefiles, at the very least.
The FreeType Project is copyright (C) 1996-2000 by David Turner, Robert Wilhelm, and Werner Lemberg. All rights reserved except as specified below. 1. No Warranty -------------THE FREETYPE PROJECT IS PROVIDED `AS IS' WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Discusses general use and applications of FreeType, as well as future and wanted additions to the library and distribution. If you are looking for support, start in this list if you haven't found anything to help you in the documentation. o freetype-devel@nongnu.org Discusses bugs, as well as engine internals, design issues, specific licenses, porting, etc. Our home page can be found at http://www.freetype.org --- end of FTL.TXT --The TWAIN Toolkit is distributed as is.
Basic Operation Printing Photos from a Computer Printing Photos from a Smartphone/Tablet Copying Printing Photos from Memory Card Printing a Disc Label from a Computer Copying a Disc Label 27
Printing Photos from a Computer This section describes how to print photos with Easy-PhotoPrint Editor. 1. Open rear tray cover (A). Pull straight up and fold back paper support (B). 2. Open the feed slot cover (C). 3. Slide right paper guide (D) to open both paper guides. 4. Load photo paper in portrait orientation WITH PRINT SIDE FACING UP.
5. Slide right paper guide (D) to align with both sides of paper stack. 6. Close feed slot cover (C) gently. After closing the feed slot cover, the paper setting confirmation screen for the rear tray appears on the touch screen.
7. If page size and media type on touch screen match size and type of paper loaded in rear tray, select Yes. If not, select Change to change the settings in accordance with the size and type of the loaded paper. 8. Open operation panel (E), and then pull out paper output tray (F) and paper output support (G). Be sure to open the operation panel before printing. If the operation panel is close, the printer does not start printing. 9. Start Easy-PhotoPrint Editor.
11. Click Browse (I) in From computer: and select folder with photos you want to print. 12. Click photos (J) you want to print and select Open (K). For Windows: To select two or more photos at a time, click photos while pressing the Ctrl key. For macOS: To select two or more photos at a time, click photos while pressing the command key. 13. Specify number of copies and other options under Print Settings (L).
For Windows: Specify the number of copies, your model name, the paper size, and other options. For macOS: Specify the number of copies, the paper size, and other options. Note • Selecting Same No. of each photo enables you to specify the number of copies for all photos with a single setting. • Selecting Same No. of each photo disables the number-of-copies setting specified for each photo. When unchecked, the previous settings for each copy are re-enabled.
Printing Photos from a Smartphone/Tablet This section describes how to print photos with Canon PRINT Inkjet/SELPHY. For details on how to download Canon PRINT Inkjet/SELPHY, see below. Print Easily from a Smartphone or Tablet with Canon PRINT Inkjet/SELPHY 1. Open rear tray cover (A). Pull straight up and fold back paper support (B). 2. Open the feed slot cover (C). 3. Slide right paper guide (D) to open both paper guides. 4. Load photo paper in portrait orientation WITH PRINT SIDE FACING UP.
5. Slide right paper guide (D) to align with both sides of paper stack. 6. Close feed slot cover (C) gently. After closing the feed slot cover, the paper setting confirmation screen for the rear tray appears on the touch screen.
7. If page size and media type on touch screen match size and type of paper loaded in rear tray, select Yes. If not, select Change to change the settings in accordance with the size and type of the loaded paper. 8. Open operation panel (E), and then pull out paper output tray (F) and paper output support (G). Be sure to open the operation panel before printing. If the operation panel is close, the printer does not start printing. 9. Start (Canon PRINT Inkjet/SELPHY) from your smartphone/tablet. 10.
13. Select Print.
Copying This section describes how to load originals and copy them to plain paper loaded in the cassette. 1. Pull out the cassette (A) from the printer. 2. Slide paper guides (B) in front and (C) on right to open guides. 3. Load plain paper in portrait orientation WITH PRINT SIDE FACING DOWN. 4. Align paper guides (B) in front and (C) on right with paper length and width.
5. Insert cassette into printer. After inserting the cassette into the printer, the paper setting confirmation screen for the cassette appears on the touch screen. 6. If page size on touch screen matches size of paper loaded in cassette, select Yes. If not, select Change to change the setting in accordance with the size of the loaded paper.
7. Open operation panel (D), and then pull out paper output tray (E) and paper output support (F). Be sure to open the operation panel before printing. If the operation panel is close, the printer does not start printing. 8. Select Copy (G) on HOME screen. 9. Select Standard copy. 10. Open document cover (H). 11. Load original WITH SIDE TO COPY FACING DOWN and align it with alignment mark (I).
Note • To copy two or more documents continuously, load them in the ADF (Auto Document Feeder). Loading Documents in the ADF (Auto Document Feeder) 12. Close the document cover. 13. Check paper settings and tap Black (J) or Color (K).
Important • Do not open the document cover until copying is complete. Note • Your printer is equipped with many other convenient copy features.
Printing Photos from Memory Card This section describes how to print photos on a memory card. 1. Open rear tray cover (A). Pull straight up and fold back paper support (B). 2. Open the feed slot cover (C). 3. Slide right paper guide (D) to open both paper guides. 4. Load photo paper in portrait orientation WITH PRINT SIDE FACING UP.
5. Slide right paper guide (D) to align with both sides of paper stack. 6. Close feed slot cover (C) gently. After closing the feed slot cover, the paper setting confirmation screen for the rear tray appears on the touch screen.
7. If page size and media type on touch screen match size and type of paper loaded in rear tray, select Yes. If not, select Change to change the settings in accordance with the size and type of the loaded paper. 8. Open operation panel (E), and then pull out paper output tray (F) and paper output support (G). Be sure to open the operation panel before printing. If the operation panel is close, the printer does not start printing. 9. Insert the memory card.
Note • For details on inserting memory cards other than SD/SDHC/SDXC, see below. Inserting the Memory Card 10. Flick right and left through the photos (H) and select one. 11. Check paper settings and tap Color (I). Important • Do not remove the memory card during printing. Data on the memory card may be damaged. Note • Your printer is equipped with many other convenient photo print features.
Printing a Disc Label from a Computer This section describes how to print photos on a printable disc with Easy-PhotoPrint Editor. Important • Do not mount the multi-purpose tray until the message prompting you to load the printable disc appears. Doing so can damage the printer. 1. Start Easy-PhotoPrint Editor. For Windows: The procedure below is for a computer running the Windows 10 operating system. From the Start menu, select (All apps >) Canon Utilities > Easy-PhotoPrint Editor.
5. Click Browse (E) in From computer: and select folder with photos you want to print. 6. Click photos (F) you want to print and select Open (G). 7. Edit disc label and select Next (H). You can change the background or add texts.
8. Open operation panel (I) until horizontal. 9. Specify number of copies and other options under Print Settings (J). For Windows: Specify the number of copies, your printer name, and other options. For macOS: Specify the number of copies and other options. 10. Start printing. For Windows: Click Print (K). For macOS: Click Next. When the Print dialog appears, specify your model name and other options, and then click Print.
11. When message prompting you to load printable disc appears on printer's touch screen, remove cassette from printer and then detach multi-purpose tray from back of cassette. Insert the removed cassette back into the printer.
12. Open multi-purpose tray guide (L) and completely press it down. 13. Place printable disc on multi-purpose tray. 1. WITH PRINT SIDE FACING UP, place printable disc, and press it against lock (M) at bottom. 2. While pressing down lock with printable disc, insert top of printable disc into slits (N).
14. Place multi-purpose tray on multi-purpose tray guide. 15. Insert multi-purpose tray straight in in horizontal direction until arrow ( tray guide is approximately aligned with arrow ( ) on multi-purpose ) on multi-purpose tray. 16. Select OK on printer's touch screen. The multi-purpose tray is drawn into the printer and printing will start. 17. After printing is complete, pull multi-purpose tray from printer to remove it.
18. While pressing down lock (M), take out printable disc from slits (N) on multi-purpose tray, and remove it. Note • Easy-PhotoPrint Editor enables you to print photos onto the disc label with various layouts.
Copying a Disc Label This section describes how to copy the label of an existing disc (BD/DVD/CD, etc.) and print it onto a printable disc. 1. Select Copy (A) on the HOME screen. 2. Select Disc label (B). 3. Check message and select OK. 4. Specify the print area of the printable disc as necessary. Select Outer circle or Inner circle (C), specify the print area, then select OK (D).
5. Specify the amount of ink (E). If the print result is blurry, select Bleed-proof. Blurring may be reduced by printing with less ink. 6. Open the document cover (F). 7. Load copy source (BD/DVD/CD, etc.) WITH ITS LABEL SIDE DOWN on platen. 8. Close the document cover. 9. Select OK on the touch screen. 10. Open operation panel (G) until horizontal.
11. Tap Black (H) or Color (I). A message prompting you to load the printable disc is displayed. 12. Remove cassette from printer and then detach multi-purpose tray from back of cassette. Insert the removed cassette back into the printer.
13. Open multi-purpose tray guide (J) and completely press it down. 14. Place printable disc on multi-purpose tray. 1. WITH PRINT SIDE FACING UP, place printable disc, and press it against lock (K) at bottom. 2. While pressing down lock with printable disc, insert top of printable disc into slits (L).
15. Place multi-purpose tray on multi-purpose tray guide. 16. Insert multi-purpose tray straight in in horizontal direction until arrow ( tray guide is approximately aligned with arrow ( ) on multi-purpose ) on multi-purpose tray. 17. Select OK on the touch screen. The multi-purpose tray is drawn into the printer and copying will start. Important • Do not open the document cover until copying is complete. 18. After copying is complete, pull multi-purpose tray from printer to remove it.
19. While pressing down lock (K), take out printable disc from slits (L) on multi-purpose tray, and remove it. Note • Your printer is equipped with many other disc label print features.
Network Available Connection Methods The following connection methods are available on the printer. • Wireless Connection Connect the printer and devices (e.g. computer/smartphone/tablet) using a wireless router. If you have a wireless router, we recommend you use one for wireless connection. ◦ Connection methods vary depending on the wireless router type. ◦ You can change network settings such as the network name (SSID) and security protocol on the printer.
Note • You can connect the printer and computer using a USB cable (USB connection). Prepare a USB cable. For details, see Connects to Another Computer via LAN/Changes from USB to LAN Connection. Network Connection Settings/Setup Perform connection setup for the printer and computer/smartphone/tablet. For more on setup procedure, click here. Changing Network Settings See below for changing connection settings for the printer and computer/smartphone/tablet.
Notice/Restriction See below for details.
Restrictions When connecting another device while a device (such as a computer) is already connected to the printer, connect it using the same connection method as the connected device. If you connect using a different connection method, the connection to the device in use will be disabled. Connection Using a Wired Network cannot be performed on printers that do not support a wired connection. Connect via wireless router • You cannot establish a printer with wireless and wired connections at the same time.
• If you connect a device and the printer using Wireless Direct, Internet connection may become unavailable depending on your environment. In that case, web services for the printer cannot be used. • In Wireless Direct mode, you can connect up to five devices at the same time. If you try to connect a sixth device while five devices are already connected, an error will appear. If an error appears, disconnect a device that does not use the printer, then configure settings again.
Network Connection Tips Default Network Settings Detect Same Printer Name Connects to Another Computer via LAN/Changes from USB to LAN Connection Printing Network Settings Reconfiguration Method of LAN Connection/Reconfiguration Method of Wi-Fi Connection 64
Default Network Settings LAN Connection Defaults Item Default Enable/Disable LAN Disable LAN Network name (SSID) BJNPSETUP Wi-Fi security Disable IP address (IPv4) Auto setup IP address (IPv6) Auto setup Set printer name* XXXXXXXXXXXX Enable/disable IPv6 Enable Enable/disable WSD Enable Timeout setting 15 minutes Enable/disable Bonjour Enable Service name Canon TS9500 series LPR protocol setting Enable RAW protocol Enable LLMNR Enable PictBridge communication Enable Wired LAN D
*1 "ab" is specified at random and "XX" represents last two digits of printer's MAC address. (The value is specified when the printer is turned on for the first time.) *2 The password is specified automatically when the printer is turned on for the first time.
Detect Same Printer Name When the printer is detected during setup, plural printers with the same name may appear on the results screen. Select a printer with checking the printer settings against those on detection result screen. • For Windows: Check the printer's MAC address or serial to select the correct printer from the results. • For macOS: The printer names appear with the MAC address added at the end or as the printer name specified by Bonjour.
Connects to Another Computer via LAN/Changes from USB to LAN Connection For Windows: For macOS: For Windows: To add a computer to connect to the printer on a LAN or to change from USB to LAN connection, perform setup using the Setup CD-ROM or from the web page. For macOS: To connect an additional computer to the printer via LAN, or to change from USB to LAN connection, perform setup from the web page.
Printing Network Settings Use the operation panel to print the printer's current network settings. Important • The network settings printout contains important information about your network. Handle it with care. 1. Check that printer is turned on, and display HOME screen. If the HOME screen is not displayed, touch the HOME button. 2. Load three sheets of A4 or Letter-sized plain paper. 3. Select (Setup) icon on HOME screen. 4. Select Device settings. 5. Select LAN settings. 6. Select Print details.
3 Wireless LAN Wireless LAN Enable/Disable 3-2 Infrastructure Infrastructure Enable/Disable 3-2-1 Signal Strength Signal strength 0 to 100 [%] 3-2-2 Link Quality Link quality 0 to 100 [%] 3-2-3 Frequency Frequency XX (GHz) 3-2-4 MAC Address MAC address XX:XX:XX:XX:XX:XX 3-2-5 Connection Connection status Active/Inactive 3-2-6 SSID SSID Wireless LAN network name (SSID) 3-2-7 Channel Channel XX (1 to 13) 3-2-8 Encryption Encryption method None/WEP/TKIP/AES 3-2-9 WEP Ke
3-2-23 Stateless Prefix Length3 Stateless prefix length 3 XXX 3-2-24 Stateless Address4 Stateless address 4 XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX 3-2-25 Stateless Prefix Length4 Stateless prefix length 4 XXX 3-2-26 Default Gateway1 Default gateway 1 XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX 3-2-27 Default Gateway2 Default gateway 2 XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX 3-2-28 Default Gateway3 Default gateway 3 XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX 3-2-29 Default Gateway4 Defaul
3-3-14 Link Local Prefix Length Link local prefix length XXX 3-3-15 IPsec IPsec setting Active 3-3-16 Security Protocol Security method – 4 Wired LAN Wired LAN Enable/Disable 4-1 MAC Address MAC address XX:XX:XX:XX:XX:XX 4-2 Connection Wired LAN status Active/Inactive 4-3 TCP/IPv4 TCP/IPv4 Enable 4-4 IP Address IP address XXX.XXX.XXX.XXX 4-5 Subnet Mask Subnet mask XXX.XXX.XXX.XXX 4-6 Default Gateway Default gateway XXX.XXX.XXX.
XXXX:XXXX:XXXX:XXXX 4-19 Default Gateway2 Default gateway 2 XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX 4-20 Default Gateway3 Default gateway 3 XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX 4-21 Default Gateway4 Default gateway 4 XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX 4-25 IPsec IPsec setting Active 4-26 Security Protocol Security method ESP/ESP & AH/AH 4-27 Wired LAN DRX Discontinuous reception (wired LAN) Enable/Disable 5 Other Settings Other settings – 5-1 Printer Name Printer name
5-19 Proxy Port Proxy port specification 1 to 65535 5-20 Cert. Fingerprt(SHA-1) Certificate fingerprint(SHA-1) xxxxxxxx xxxxxxxx xxxxxxxx Cert.
Reconfiguration Method of LAN Connection/Reconfiguration Method of Wi-Fi Connection Reconfiguration Method of LAN Connection Reconfiguration Method of Wi-Fi Connection Reconfiguration Method of LAN Connection Follow either procedure below to change LAN connection method (wired or Wi-Fi). • For Windows: ◦ Redo setup using the Setup CD-ROM or from the web page.
4. If message saying setup is completed appears, select OK. • For macOS: Redo setup from the web page.
IJ Network Device Setup Utility (macOS) IJ Network Device Setup Utility Starting Up IJ Network Device Setup Utility Diagnosing and Repairing Network Settings List of Models Which Does Not Support Diagnosis and Repair Function 77
IJ Network Device Setup Utility If anything is wrong with connection, IJ Network Device Setup Utility diagnoses the settings of the printer and those of computer on which it is installed. In addition, IJ Network Device Setup Utility restores the status of the printer and computer. Important • To use the printer over LAN, make sure you have the equipment necessary for the connection type, such as a wireless router or a LAN cable.
Starting Up IJ Network Device Setup Utility Start up Launchpad, select Canon Utilities, and then select IJ Network Device Setup Utility. When you start up IJ Network Device Setup Utility, the screen below appears. Enter the password specified for your computer and select Install Helper. IJ Network Device Setup Utility starts diagnosis and repair of network.
Diagnosing and Repairing Network Settings IJ Network Device Setup Utility diagnoses and repairs computer settings or connection between the computer and printer when a problem (e.g. cannot print from a printer on the network) occurs. Important • Some models do not support diagnosis and repair function. For details: List of Models Which Does Not Support Diagnosis and Repair Function IJ Network Device Setup Utility starts checking the computer settings when it starts up.
List of Models Which Does Not Support Diagnosis and Repair Function The following models does not support "Diagnose and Repair" function of IJ Network Device Setup Utility.
Handling Paper, Originals, Ink Tanks, Multi-purpose Tray, Memory Card, etc.
Loading Paper Paper Sources Loading Paper in the Rear Tray Loading Paper in the Cassette Loading Envelopes in Rear Tray 83
Paper Sources The printer has two paper sources for feeding paper, the rear tray (A) and cassette (B). You can load all supported paper on the rear tray. Supported Media Types You can load A4, B5, A5, or Letter-sized plain paper in the cassette. Note • When printing, select the correct page size and media type. If you select the wrong page size or media type, the printer may feed paper from the wrong paper source or may not print with the proper print quality.
Loading Paper in the Rear Tray You can load plain paper or photo paper. You can also load envelopes on the rear tray. Loading Envelopes in Rear Tray Important • If you cut plain paper to a size of 5" x 7" (13 x 18 cm) or smaller to perform a trial print, it may cause a paper jam. Note • We recommend Canon genuine photo paper for printing photos. For details on the Canon genuine paper, see Supported Media Types.
3. Open the feed slot cover (C). 4. Slide right paper guide (D) to open both paper guides. 5. Load paper stack in portrait orientation WITH PRINT SIDE FACING UP.
6. Slide right paper guide (D) to align with both sides of paper stack. Do not slide the paper guides too hard against the paper. The paper may not be fed properly. Important • Always load paper in portrait orientation (E). Loading paper in landscape orientation (F) can cause paper jams. Note • Do not load sheets of paper higher than the load limit mark (G). 7. Close feed slot cover (C) gently.
Important • If the feed slot cover is open, paper cannot be fed. Be sure to close the feed slot cover. After closing the feed slot cover, the paper setting confirmation screen for the rear tray appears on the touch screen. 8. If page size and media type on touch screen match size and type of paper loaded in rear tray, select Yes. If not, select Change to change the settings in accordance with the size and type of the loaded paper. 9.
Note • There are various types of paper, such as paper with a special surface coating for printing photos at optimal quality and paper suitable for documents. Each media type has specific preset settings (how ink is used and sprayed, distance from nozzles, etc.), that allow you to print to that type with optimal image quality. The wrong paper settings may cause poor printout color quality or scratches on the printed surface.
Loading Paper in the Cassette You can load A4, B5, A5, or Letter-sized plain paper in the cassette. Note • In the cassette, be sure to load only plain paper. • You can use general copy paper or Canon Red Label Superior WOP111/Canon Océ Office Colour Paper SAT213. For the page size and paper weight you can use for this printer, see Supported Media Types. 1. Prepare paper. Align the edges of paper. If paper is curled, flatten it. Note • Align the edges of paper neatly before loading.
4. Load paper stack in portrait orientation WITH PRINT SIDE FACING DOWN, and place it in center of cassette. Important • Always load paper in portrait orientation (D). Loading paper in landscape orientation (E) can cause paper jams. Note • Align the paper stack with the edge of the cassette as shown in the figure below. If the paper stack is in contact with the protrusion (F), the paper may not be fed properly.
5. Slide front paper guide (B) to align it with paper stack. Align paper guide with where it clicks into place. 6. Slide right paper guide (C) to align it with paper stack. Do not slide the paper guide too hard against the paper. The paper may not be fed properly. Note • Do not load sheets of paper higher than the load limit mark (G). • Keep the paper stack height below the tabs (H) of the paper guides.
7. Insert cassette into printer. Push the cassette into the printer until it stops. After inserting the cassette into the printer, the paper setting confirmation screen for the cassette appears on the touch screen. 8. If page size on touch screen matches size of paper loaded in cassette, select Yes. If not, select Change to change the setting in accordance with the size of the loaded paper. 9. Open operation panel (I), and then pull out paper output tray (J) and paper output support (K).
Be sure to open the operation panel before printing. If the operation panel is close, the printer does not start printing. Note • To prevent incorrect printing, this printer has a function that detects whether the settings for the paper loaded in the cassette matches the paper settings. Before printing, make print settings in accordance with the paper settings. When this function is enabled, an error message is displayed if these settings do not match to prevent incorrect printing.
Loading Envelopes in Rear Tray You can load Envelope DL and Envelope Com 10 on the rear tray. The address is automatically rotated and printed according to the envelope's direction by specifying with the printer driver properly. Important • Printing of envelopes from the operation panel or from a PictBridge (Wi-Fi) compliant device is not supported. • Do not use the following envelopes. They could jam in the printer or cause the printer to malfunction.
3. Open the feed slot cover (C). 4. Slide right paper guide (D) to open both paper guides. 5. Load envelopes in portrait orientation WITH PRINT SIDE FACING UP. Up to 10 envelopes can be loaded at once. Fold flap of the envelope and load the envelope in portrait orientation with the address side facing up. 6. Slide right paper guide (D) to align with both sides of envelopes. Do not slide the paper guides too hard against the envelopes. The envelopes may not be fed properly.
Note • Do not load envelopes higher than the load limit mark (E). 7. Close feed slot cover (C) gently. Important • If the feed slot cover is open, paper cannot be fed. Be sure to close the feed slot cover.
After closing the feed slot cover, the paper setting confirmation screen for the rear tray appears on the touch screen. 8. If page size and media type shown on touch screen match size and type of envelopes loaded in rear tray, select Yes. If not, select Change to change the settings in accordance with the size and type of the loaded envelopes. 9. Open operation panel (F), and then pull out paper output tray (G) and paper output support (H). Be sure to open the operation panel before printing.
Note • To prevent incorrect printing, this printer has a function that detects whether the settings for the paper loaded on the rear tray matches the paper settings. Before printing, make print settings in accordance with the paper settings. When this function is enabled, an error message is displayed if these settings do not match to prevent incorrect printing. When this error message is displayed, check and correct the paper settings.
Placing Multi-purpose Tray Cautions When Printing with Multi-purpose Tray Placing a Printable Disc How to Detach / Attach Multi-purpose Tray 100
Cautions When Printing with Multi-purpose Tray Cautions Common to using Multi-purpose Tray • Be sure to use the multi-purpose tray supplied with this printer. • Do not mount the multi-purpose tray while the printer is in operation. • Do not remove the multi-purpose tray while the printer is in operation. Doing so may damage the printer, the multi-purpose tray, or the media. • Do not get dirt on the multi-purpose tray or scratches on the reflectors.
Placing a Printable Disc Before Placing a Printable Disc Placing a Printable Disc Removing a Printable Disc 102
Before Placing a Printable Disc A printable disc differs from regular disc (BD/DVD/CD, etc.) in that its label surface has been specially processed or printing by an inkjet printer. The following items are needed to print onto the printable disc. • Multi-purpose tray (supplied with the printer) The multi-purpose tray is stored in the back of the cassette. • 4.72 inches (12 cm) printable disc Obtain a printable disc with a label surface compatible with inkjet printing.
Placing a Printable Disc To print onto a printable disc, place it on the supplied multi-purpose tray, and then insert it into the printer. This procedure also applies to printing from a computer. Important • Do not mount the multi-purpose tray until the message prompting you to load the printable disc appears. Doing so can damage the printer.
Note • After inserting the cassette into the printer, if a message appears on the screen, select Yes. 2. Open multi-purpose tray guide (A) and completely press it down. 3. Place printable disc on multi-purpose tray. Important • Check that there is no dirt on the multi-purpose tray before placing a printable disc on it. • When placing a printable disc on the multi-purpose tray, do not touch the printing surface of the disc or the reflectors (B) on the multi-purpose tray. 1.
2. While pressing down lock with printable disc, insert top of printable disc into slits (D). 4. Place multi-purpose tray on multi-purpose tray guide. 5. Insert multi-purpose tray straight in in horizontal direction until arrow ( tray guide is approximately aligned with arrow ( ) on multi-purpose ) on multi-purpose tray. Important • Do not insert the multi-purpose tray beyond the arrow ( 106 ) on the multi-purpose tray guide.
Note • The multi-purpose tray may be ejected after a certain amount of time passes. In such a case, follow the on-screen instructions to place the multi-purpose tray again.
Removing a Printable Disc 1. Pull out multi-purpose tray. 2. While pressing down lock (A), take out printable disc from slits (B) on multi-purpose tray, and remove it. Important • Do not touch the printing surface when removing the disc from the multi-purpose tray. Note • Allow the printing surface to dry before removing the disc.
Important • When the multi-purpose tray guide is open, you cannot print onto regular printing paper. Be sure to close the multi-purpose tray guide. 4. Store multi-purpose tray under cassette.
How to Detach / Attach Multi-purpose Tray Detaching Multi-purpose Tray 1. Take cassette out of printer. Be sure to remove any paper. 2. Turn cassette over and remove multi-purpose tray. Slide the multi-purpose tray, take it out of the six tabs (A), and then lift it. Important • Be sure to remove any orange shipping tape on the multi-purpose tray.
Attaching Multi-purpose Tray 1. Take cassette out of printer. Be sure to remove any paper. 2. Turn cassette over and attach multi-purpose tray to it. Turn the multi-purpose tray so that its underside faces up, align it with the six tabs (A) in the orientation shown in the figure below, and then slide to attach. Important • Insert the multi-purpose tray, making sure that its holes are aligned with the tabs on the back of the cassette.
Loading Originals Where to Load Originals Loading Originals on Platen Loading Documents in the ADF (Auto Document Feeder) Loading Based on Use Supported Originals 112
Where to Load Originals The printer has two positions to load originals: platen and ADF (Auto Document Feeder). Select the position to load the original according to the size, type, or usage. Note • For details on the supported originals, see below. Supported Originals Loading Documents, Photos, or Book on Platen Loading Two or More Sheets of Document of the Same Size and Thickness in the ADF You can also load a sheet of document in the ADF.
Loading Originals on Platen 1. Open the document cover. 2. Load original WITH SIDE TO SCAN FACING DOWN on platen. Loading Based on Use Supported Originals Important • Be sure to observe the following when loading the original on the platen. Failure to observe the following may cause the scanner to malfunction or the platen glass to break. • Do not place any objects weighing 4.4 lb (2.0 kg) or more on the platen glass. • Do not put any pressure of 4.4 lb (2.
Important • After loading the original on the platen, be sure to close the document cover before starting to copy or scan.
Loading Documents in the ADF (Auto Document Feeder) Note • To scan a document at optimum quality, load it on the platen. 1. Make sure any original has been removed from platen. 2. Open document tray (A). 3. Slide the paper guides (B) all the way out. 4. Load document WITH SIDE TO SCAN FACING UP in document tray. Insert the document until it stops. Note • For details on the supported originals, see below. Supported Originals 5. Adjust document guide (B) to match width of document.
Loading Based on Use Load the original in the correct position according to the function to use. If you do not load the original correctly, it may not be scanned properly. Originals Magazines, Newspapers, and Documents Function Copying Scanning by detecting the type and size of the original automatically How to Load Loading the Original to Be Aligned with the alignment mark If you scan using the operation panel, select Auto scan for Doc.type in Scan.
Loading the Original to Be Aligned with the alignment mark Place the original WITH THE SIDE TO SCAN FACING DOWN on the platen and align it with the alignment mark . Portions placed on the diagonally striped area cannot be scanned. Important • The printer cannot scan the striped area (A) (0.04 inch (1 mm) from the edges of the platen glass). Loading Only One Original in Center of Platen Place the original WITH THE SIDE TO SCAN FACING DOWN, with 0.
Loading Two or More Originals on Platen Place the originals WITH THE SIDE TO SCAN FACING DOWN. Allow 0.40 inch (1 cm) or more space between the edges (diagonally striped area) of the platen and the originals, and between the originals. Portions placed on the diagonally striped area cannot be scanned. You can place up to 12 items. B: More than 0.40 inch (1 cm) Note • The Skew Correction function automatically compensates for the originals placed at an angle of up to approximately 10 degrees.
Supported Originals Platen Item Details Types of originals • Text document, magazine, or newspaper • Printed photo, postcard, business card, or disc (BD/DVD/CD, etc.) • Documents that are not suitable for the ADF Size (width x height) Max. 8.5 x 11.7 inches (216 x 297 mm) Quantity One or more sheets* Thickness Max. 0.2 inch (5 mm) * Two or more originals can be loaded on the platen depending on the selected function.
• Documents on carbon paper • Documents on coated paper • Documents on onion skin or other thin paper • Photos or excessively thick documents 122
Inserting the Memory Card Before Inserting the Memory Card Inserting the Memory Card Removing the Memory Card 123
Before Inserting the Memory Card The following types of memory cards and image data are compatible with the printer. Important • If you took and saved photos on a type of memory card that does not guarantee the operation on your PictBridge (Wi-Fi) compliant device, the image data may be unreadable on the printer or damaged.
Printable Image Data • This printer accepts images taken with a camera compliant with the Design rule for Camera File system (Exif 2.2/2.21/2.3 compliant), TIFF (Exif 2.2/2.21/2.3 compliant). Other image or movie types such as RAW images cannot be printed. • The printer accepts images scanned and saved with the printer when Doc.type is set to Photo and Format is set to JPEG (file extension ".jpg"). Note • This device incorporates exFAT technology licensed from Microsoft.
Inserting the Memory Card Important • When a memory card is inserted into the card slot, the Access lamp is lit. When the Access lamp is flashing, the printer is accessing the memory card. In this case, do not touch the area around the card slot. Note • When Read/write attribute is set to Writable from USB PC, you cannot print image data from the memory card using the operation panel of the printer.
Important • Part of the memory card will protrude from the card slot, but do not force it into the slot any further. This can damage the printer or the memory card. • Make sure that the memory card is correctly oriented before inserting it into the card slot. If you force the memory card into the card slot in the wrong orientation, the memory card or the printer can be damaged.
Removing the Memory Card Important • If you used the card slot as the memory card drive of a computer, you must perform the "safe removal" operation on your computer before physically removing the memory card from the printer. Setting Up Card Slot as Memory Card Drive of Computer 1. Make sure that the Access lamp is lit, and remove the memory card. Hold the part of the memory card that is protruding and remove it straightforward from the printer.
Replacing Ink Tanks Replacing Ink Tanks Checking Ink Status on the Touch Screen Ink Tips 129
Replacing Ink Tanks When remaining ink cautions or errors occur, the message will appear on the touch screen to inform you of the error. In this state, the printer cannot print or scan. Take appropriate action according to the message. An Error Occurs Note • If print results become faint or white streaks appear despite sufficient ink levels, see Maintenance Procedure. • For precautionary notes on handling ink tanks, see Notes on ink tanks.
Important • Do not touch other parts besides the ink tanks. • Handle the ink tank carefully to avoid staining of clothing or the surrounding area. • Discard the empty ink tank according to the local laws and regulations regarding disposal of consumables. Note • Do not remove two or more ink tanks at the same time. Be sure to replace ink tanks one by one when replacing two or more ink tanks. 4.
5. Hold the ink tank with the orange protective cap (E) pointing up while being careful not to block the Y-shape air hole (D). 6. Lift up the tab on the orange protective cap (E) to remove it off GENTLY. Important • Do not push the sides of the ink tank. If you push the sides of the ink tank with the Y-shape air hole (D) blocked, ink may splash. • Do not touch the inside of the orange protective cap (E) or the open ink port (F). The ink may stain your hands if you touch them.
8. Press on the top of the ink tank until the ink tank snaps firmly into place. Important • You cannot print if the ink tank is installed in the wrong position. Be sure to install the ink tank in the correct position according to the label on the print head holder. • You cannot print unless all the ink tanks are installed. Be sure to install all the ink tanks. 9. Close the scanning unit / cover. To close the scanning unit / cover, hold it up once, then take it down gently.
Note • If the error message appears after the scanning unit / cover is closed, take appropriate action. An Error Occurs • When you start printing after replacing the ink tank, the printer starts cleaning the print head automatically. Do not perform any other operations until the printer completes the cleaning of the print head. • If the print head is out of alignment, as indicated by misaligned printed ruled lines or similar symptoms, align the print head. • The printer may make noise during operation.
Checking Ink Status on the Touch Screen 1. Make sure that the power is turned on, and display the HOME screen. If the HOME screen is not displayed, tap 2. Select (HOME) to display it. (Hint) on HOME screen. Using the Operation Panel The hint menu screen will appear. 3. Select Estimated ink levels. A symbol appears in the area A if there is any information about the remaining ink level. Example: The ink is running low. Prepare a new ink tank.
Ink Tips How is ink used for various purposes other than printing? Ink may be used for purposes other than printing. When you use the Canon printer for the first time after you install the bundled ink tanks, the printer consumes a small amount of ink in the amount to enable printing by filling the nozzles of the Print Head with ink. For this reason, the number of sheets that can be printed with the first ink tanks is fewer than the succeeding ink tanks.
If Printing Is Faint or Uneven Maintenance Procedure Printing the Nozzle Check Pattern Examining the Nozzle Check Pattern Cleaning the Print Head Deep Print Head Cleaning Aligning the Print Head Aligning the Print Head Manually 137
Maintenance Procedure If print results are blurred, colors are not printed correctly, or print results are unsatisfactory (e.g. misaligned printed ruled lines), perform the maintenance procedure below. Important • Do not rinse or wipe the print head and ink tank. This can cause trouble with the print head and ink tank. Note • Make sure that the orange protective tape does not remain on the ink tank. • Check the ink status.
Step3 Clean the print head. From the printer Cleaning the Print Head From the computer • For Windows: Cleaning the Print Heads • For macOS: Cleaning the Print Heads After cleaning the print head, print and examine the nozzle check pattern: Step1 If the problem is not resolved after performing from step 1 to step 3 twice: Step4 Clean the print head deeply.
Adjusting Print Head Position 140
Printing the Nozzle Check Pattern Print the nozzle check pattern to determine whether the ink ejects properly from the print head nozzle. Note • If the remaining ink level is low, the nozzle check pattern will not be printed correctly. Replace the ink tank whose ink is low. You need to prepare: a sheet of A4 or Letter-sized plain paper 1. Check that printer is turned on. 2. Load a sheet of A4 or Letter-sized plain paper in the cassette.
The confirmation screen will appear. 7. Select Yes. The nozzle check pattern will be printed and two pattern confirmation screens will appear on the touch screen. 8. Examine the nozzle check pattern.
Examining the Nozzle Check Pattern Examine the nozzle check pattern, and clean the print head if necessary. 1. Check if there are missing lines in the pattern C or horizontal white streaks in the pattern D. A: No missing lines/No horizontal white streaks B: Lines are missing/Horizontal white streaks are present 2. Select the pattern that is closer to the printed nozzle check pattern on the confirmation screen.
For A (no missing lines or no horizontal white streaks) in both the pattern C and pattern D: The cleaning is not required. Select All A, confirm the message, then select OK. The screen will return to the Maintenance screen. For B (lines are missing or horizontal white streaks are present) in the pattern C or pattern D, or in both patterns: The cleaning is required. Select Also B, then select Yes on the cleaning confirmation screen. The printer starts cleaning the print head.
Cleaning the Print Head Clean the print head if lines are missing or if horizontal white streaks are present in the printed nozzle check pattern. Cleaning unclogs the nozzles and restores the print head condition. Cleaning the print head consumes ink, so clean the print head only when necessary. You need to prepare: a sheet of A4 or Letter-sized plain paper 1. Check that printer is turned on. 2. Load a sheet of A4 or Letter-sized plain paper in the cassette.
The confirmation screen will appear. 7. Select Yes. The printer starts cleaning the print head. Do not perform any other operations until the printer completes the cleaning of the print head. This takes about 1 minute. The pattern print confirmation screen will appear. 8. Select Yes. The nozzle check pattern will be printed. 9. Examine the nozzle check pattern. Note • If the problem is not resolved after cleaning the print head twice, clean the print head deeply.
Deep Print Head Cleaning If print quality does not improve by the standard cleaning of the print head, clean the print head deeply. Cleaning the print head deeply consumes more ink than the standard cleaning of the print head, so clean the print head deeply only when necessary. You need to prepare: a sheet of A4 or Letter-sized plain paper 1. Check that printer is turned on. 2. Load a sheet of A4 or Letter-sized plain paper in the cassette.
The confirmation screen will appear. 7. Select Yes. The printer starts cleaning the print head deeply. Do not perform any other operations until the printer completes the deep cleaning of the print head. This takes about 1 to 2 minutes. The pattern print confirmation screen will appear. 8. Select Yes. The nozzle check pattern will be printed. 9. When the completion message appears, select OK. 10. Examine the nozzle check pattern.
Aligning the Print Head If printed ruled lines are misaligned or print results are otherwise unsatisfactory, adjust the print head position. Note • If the remaining ink level is low, the print head alignment sheet will not be printed correctly. Replace the ink tank whose ink is low. • If ink runs out as the print head alignment sheet is printed, an error message appears on the touch screen. An Error Occurs You need to prepare: two sheets of A4 or Letter-sized plain paper 1.
5. Select Maintenance. The Maintenance screen will appear. 6. Select Auto head alignment. The confirmation screen will appear. 7. Confirm the message, then select Yes. The print head alignment sheet is printed, and the print head is aligned automatically. This takes about 3 to 4 minutes. Note • If automatic print head alignment fails, an error message appears on the touch screen. An Error Occurs 8. When the completion message appears, select OK.
Aligning the Print Head Manually Try aligning the print head manually after automatic print head alignment if printing results are not as expected, as when printed ruled lines are misaligned. Note • For details on automatic print head alignment, see Aligning the Print Head. What you will need: three sheets of A4 or Letter-sized plain paper 1. Check that printer is turned on. 2. Load three sheets of A4 or Letter-sized plain paper in cassette.
6. Select Manual head alignment. The confirmation screen will appear. Note • To print and check the current head position alignment values, select Print the head alignment value. 7. Check message and select Yes. The print head alignment pattern will be printed. 8. When Did the patterns print correctly? appears, make sure pattern was printed correctly, and if so, select Yes. 9. Check message and select Next. The input screen for head position alignment values is displayed. 10.
Note • If all patterns look different, choose the pattern in which vertical streaks are least noticeable. Subtle vertical streaks Noticeable vertical streaks • If all patterns look different, choose the pattern in which horizontal streaks are least noticeable. Subtle horizontal streaks Noticeable horizontal streaks 11. Repeat these steps until you have finished entering pattern numbers for columns B to H, and then select OK. 12. Check message and select OK. The second set of patterns is printed. 13.
Note • If all patterns look different, choose the pattern in which vertical streaks are least noticeable. Subtle vertical streaks Noticeable vertical streaks 14. Repeat these steps until you have finished entering pattern numbers for columns J to P, and then select OK. 15. Check message and select OK. The third set of patterns is printed. 16. Examine third patterns and tap a. In column a, find pattern in which stripes are least noticeable, and then select the number of that pattern.
Note • If all patterns look different, choose the pattern in which horizontal stripes are least noticeable. Subtle horizontal stripes Noticeable horizontal stripes 17. Repeat these steps until you have finished entering pattern numbers for columns b to h, and then select OK. 18. When confirmation message appears, select OK.
Performing Maintenance Functions from Your Computer (macOS) Opening Remote UI for Maintenance Cleaning the Print Heads Adjusting Print Head Position Checking Ink Status from Your Computer 156
Opening Remote UI for Maintenance You can perform maintenance of printer and change the settings from a Remote UI. The following is the procedure to open a Remote UI. 1. Open System Preferences, and select Printers & Scanners 2. Select your model from the printer list, and click Options & Supplies... 3. Click Show Printer Webpage... in General tab Remote UI starts. Note • The password may have to be entered after Remote UI starts. In such a case, enter the password and click OK.
Cleaning the Print Heads The print head cleaning function allows you to clear up clogged print head nozzle. Perform print head cleaning if printing is faint or a specific color fails to print, even though there is enough ink. Cleaning 1. Select Utilities from Remote UI 2. Click Cleaning Before running the cleaning, check the following items: Check whether the printer is on and open the printer's scanning unit / cover. Check the following items for each ink. Then, if necessary, perform Cleaning.
2. Click Deep cleaning Before running the deep cleaning, check the following items: Check whether the printer is on and open the printer's scanning unit / cover. Check the following items for each ink. Then, if necessary, perform Deep cleaning. • Is there ink remaining in the tank? • Did you push in the ink tank completely until you heard a clicking sound? • If the orange tape is there, has it been peeled off completely? Any remaining tape will hinder ink output.
Adjusting Print Head Position Any error in the print head installation position can cause color and line shifts. Adjusting the print head position improves print results. Auto head alignment 1. Select Utilities from Remote UI 2. Click Auto head alignment A message appears. 3. Load paper in printer In the cassette, load 2 sheets of plain A4-sized or Letter-sized paper. 4. Run head position adjustment Check that the printer power is on, and then click Yes. Head alignment starts.
Checking Ink Status from Your Computer You can check the detailed information such as the remaining ink level and the ink tank types of your model. If you select Printer status from Remote UI, the ink status appears as an illustration. Estimated ink levels You can check the types and levels of ink. When ink levels are running low or an error occurs because there is no ink, a notification icon will appear. Ink number You can look up the correct ink tank for your printer.
Cleaning Cleaning Exterior Surfaces Cleaning Platen and Document Cover Cleaning the ADF (Auto Document Feeder) Cleaning Paper Feed Rollers Cleaning Inside the Printer (Bottom Plate Cleaning) Cleaning Cassette Pads 162
Cleaning Paper Feed Rollers If the paper feed roller is dirty or paper powder is attached to it, paper may not be fed properly. In this case, clean the paper feed roller. Cleaning will wear out the paper feed roller, so perform this only when necessary. You need to prepare: three sheets of A4 or Letter-sized plain paper 1. Check that printer is turned on. 2. Select (Setup) on HOME screen. Using the Operation Panel The setup menu screen will appear. 3. Select Maintenance.
9. Make sure that the paper feed roller has stopped rotating, then follow the message to load the three sheets of A4 or Letter-sized plain paper. 10. Open operation panel and pull out paper output tray. 11. Select OK. The printer starts cleaning. The cleaning will be complete when the paper is ejected. 12. When the completion message appears, select OK. If the problem is not resolved after cleaning the paper feed roller, contact your nearest Canon service center to request a repair.
Cleaning Inside the Printer (Bottom Plate Cleaning) Remove stains from the inside of the printer. If the inside of the printer becomes dirty, printed paper may get dirty, so we recommend performing cleaning regularly. You need to prepare: a sheet of A4 or Letter-sized plain paper* * Be sure to use a new piece of paper. 1. Check that printer is turned on. 2. Select (Setup) on HOME screen. Using the Operation Panel The setup menu screen will appear. 3. Select Maintenance.
9. Load only this sheet of paper in the cassette with the ridges of the creases facing up and the edge of the half with no crease facing to the far side. 10. Insert cassette into printer. 11. Open operation panel and pull out paper output tray. 12. Select OK. The paper cleans the inside of the printer as it feeds through the printer. Check the folded parts of the ejected paper. If they are smudged with ink, perform Bottom Plate Cleaning again. 13. When the completion message appears, select OK.
If the problem is not resolved after performing cleaning again, the protrusions inside the printer may be stained. Wipe off any ink from the protrusions using a cotton swab or the like. Important • Be sure to turn off the power and unplug the power cord before cleaning the printer.
Overview Safety Safety Precautions Regulatory Information WEEE (EU & EEA) Handling Precautions Canceling Print Jobs Legal Restrictions on Scanning/Copying Transporting Your Printer When Repairing, Lending, or Disposing of the Printer Keeping Print Quality High Main Components and Their Use Main Components Power Supply Using the Operation Panel Changing Settings Changing Printer Settings from Your Computer (Windows) Changing Printer Settings from Your Computer (macOS) Changing Settings from Operation Panel S
Safety Safety Precautions Regulatory Information WEEE (EU&EEA) 169
Safety Precautions Safety Precautions • This manual contains important notices and safety precautions about your printer. Do not use the printer in ways other than described in the accompanying manuals, as this may result in fire, electric shock or other unexpected accidents. Safety standard marks and declarations are only valid for the supported voltages and frequencies in the applicable countries or regions. Warning • Users with cardiac pacemakers: This product emits a low-level magnetic flux.
• In case ink gets in contact with eyes, rinse with water immediately. In case ink gets in contact with skin, wash with soap and water immediately. If irritation to eyes or skin persists, obtain medical advice immediately. • Moving the printer • Do not hold the printer by the cassette. Hold the printer by its sides and carry it with both hands. General Notices Choosing a location Refer to "Specifications" in the Online manual for details on operating environment.
• Do not place anything on top of the printer. Be especially careful to avoid metal objects such as paper clips and staples, and containers holding flammable liquids such as alcohol or thinner. • Do not apply excessive pressure when placing large objects on the platen glass. • Do not attempt to open, disassemble or modify the ink tanks. Ink may leak and damage your printer. • Do not throw print heads or ink tanks in the fire.
Regulatory Information Users in the U.S.A. FCC Notice (U.S.A. Only) For 120V, 60Hz model Model Number: K10480 (Contains FCC Approved WLAN Module K30365, FCC Approved Bluetooth K30375) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Interference Do not use the printer around medical equipment or other electronic devices. Signals from the printer may interfere with the correct operation of these devices.
WEEE (EU&EEA) Only for European Union and EEA (Norway, Iceland and Liechtenstein) This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/19/EU) and national legislation. This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE).
Ce symbole indique que ce produit ne doit pas être jeté avec les ordures ménagères, conformément à la directive DEEE (2012/19/UE) et à la réglementation de votre pays. Ce produit doit être confié au distributeur à chaque fois que vous achetez un produit neuf similaire, ou à un point de collecte mis en place par les collectivités locales pour le recyclage des Déchets des Équipements Électriques et Électroniques (DEEE).
peligrosas que normalmente están asociadas con los RAEE. Al mismo tiempo, su cooperación a la hora de desechar correctamente este producto contribuirá a la utilización eficazde los recursos naturales. Para más información sobre cómo puede eliminar el equipo para su reciclado, póngase en contacto con las autoridades locales, con las autoridades encargadas de los desechos, con un sistema de gestión RAEE autorizado o con el servicio de recogida de basuras doméstico.
Apenas para a União Europeia e AEE (Noruega, Islândia e Liechtenstein) Este símbolo indica que o produto não deve ser colocado no lixo doméstico, de acordo com a Directiva REEE (2012/19/UE) e a legislação nacional. Este produto deverá ser colocado num ponto de recolha designado, por exemplo, num local próprio autorizado quando adquirir um produto semelhante novo ou num local de recolha autorizado para reciclar resíduos de equipamentos eléctricos e electrónicos (EEE).
Αυτό το σύμβολο υποδηλώνει ότι αυτό το προϊόν δεν πρέπει να απορρίπτεται μαζί με τα οικιακά απορρίμματα, σύμφωνα με την Οδηγία σχετικά με τα Απόβλητα Ηλεκτρικού και Ηλεκτρονικού Εξοπλισμού (ΑΗΗΕ) (2012/19/ΕΕ) και την εθνική σας νομοθεσία. Αυτό το προϊόν πρέπει να παραδίδεται σε καθορισμένο σημείο συλλογής, π.χ. σε μια εξουσιοδοτημένη βάση ανταλλαγής όταν αγοράζετε ένα νέο παρόμοιο προϊόν ή σε μια εξουσιοδοτημένη θέση συλλογής για την ανακύκλωση των αποβλήτων Ηλεκτρικού και Ηλεκτρονικού Εξοπλισμού (ΗΗΕ).
kierrätysjärjestelmän ylläpitäjältä ja jätehuoltoyhtiöltä. Lisätietoja sähkö- ja elektroniikkalaiteromun keräyksestä ja kierrätyksestä on osoitteessa www.canon-europe.com/weee. Endast för Europeiska unionen och EES (Norge, Island och Liechtenstein) Den här symbolen visar att produkten enligt WEEE-direktivet (2012/19/EU) och nationell lagstiftning inte får sorteras och slängas som hushållsavfall. Den här produkten ska lämnas in på en därför avsedd insamlingsplats, t.ex.
Ez a szimbólum azt jelzi, hogy a helyi törvények és a WEEE-irányelv (2012/19/EU) szerint a termék nem kezelhető háztartási hulladékként. A terméket a kijelölt nyilvános gyűjtőpontokon kell leadni, például hasonló cserekészülék vásárlásakor, illetve bármelyik, elektromos és elektronikai berendezésekből származó hulladék (WEEE) átvételére feljogosított gyűjtőponton.
k účinnému využívaniu prírodných zdrojov. Ďalšie informácie o mieste recyklácie opotrebovaných zariadení získate od miestneho úradu, úradu životného prostredia, zo schváleného plánu OEEZ alebo od spoločnosti, ktorá zaisťuje likvidáciu komunálneho odpadu. Viac informácií nájdete aj na webovej stránke: www.canon-europe.com/weee.
elektros ir elektroninės įrangos (EEĮ) atliekų perdirbimo punktą. Netinkamas tokios rūšies atliekų tvarkymas dėl elektros ir elektroninėje įrangoje esančių pavojingų medžiagų gali pakenkti aplinkai ir žmonių sveikatai. Padėdami užtikrinti tinkamą šio gaminio šalinimo tvarką, kartu prisidėsite prie veiksmingo gamtos išteklių naudojimo.
Doar pentru Uniunea Europeană şi EEA (Norvegia, Islanda şi Liechtenstein) Acest simbol indică faptul că acest produs nu trebuie aruncat o dată cu reziduurile menajere, în conformitate cu Directiva DEEE (Directiva privind deşeurile de echipamente electrice şi electronice) (2012/19/UE) şi legile naţionale.
vrstom otpada može da ima moguće negativne posledice po životnu sredinu i ljudsko zdravlje usled potencijalno opasnih materijala koji se uglavnom vezuju za EEE. U isto vreme, vaša saradnja na ispravnom odlaganju ovog proizvoda će doprineti efikasnom korišćenju prirodnih resursa. Za više informacija o tome gde možete da predate vašu staru opremu radi recikliranje, vas molimo, da kontaktirate lokalne gradske vlasti, komunalne službe, odobreni plan reciklaže ili Gradsku čistoću.
Handling Precautions Canceling Print Jobs Legal Restrictions on Scanning/Copying Transporting Your Printer When Repairing, Lending, or Disposing of the Printer Keeping Print Quality High 186
Legal Restrictions on Scanning/Copying Scanning, printing, copying, or modifying copies of the following may be punishable under law. This list is non-exhaustive. When in doubt, check with a local legal representative.
Transporting Your Printer When relocating the printer for changing your living place or repairing it, make sure of the following. Important • Pack the printer in a sturdy box so that it is placed with its bottom facing down, using sufficient protective material to ensure safe transport. • With the print head and ink tank left installed in the printer, press the ON button to turn off the power. This allows the printer to automatically cap the print head, thus preventing it from drying.
When Repairing, Lending, or Disposing of the Printer If you have entered personal data, passwords and/or other security settings on the printer, such information may be stored in the printer. When sending the printer for repair, lending or transferring the printer to another person, or disposing of the printer, please be sure to follow the steps below in order to delete such information and prevent third parties from accessing it. • Select Yes.
Keeping Print Quality High The key to printing with the optimal printing quality is to prevent the print head from drying or clogging. Always observe the following rules for optimal printing quality. Note • Depending on the type of paper, ink may blur if you trace the printed area with a highlight pen or paintstick, or bleed if water or sweat comes in contact with the printed area.
Main Components and Their Use Main Components Power Supply Using the Operation Panel 191
Main Components Front View Rear View Inside View Operation Panel 192
Front View A: Operation Panel Use to change the settings of the printer or to operate it. Before printing starts, this automatically opens. Operation Panel B: Platen Load an original here. C: Document Cover Open to load an original on the platen. D: Cassette Load A4, B5, A5, or Letter-sized plain paper into the cassette, and insert it into the printer. Loading Paper in the Cassette E: Paper Guides Align with right/left/front sides of the paper stack.
I: Card Slot Insert a memory card. Before Inserting the Memory Card J: Access lamp Lights or flashes to indicate the memory card status. Inserting the Memory Card K: Multi-purpose Tray Guide Place the multi-purpose tray here. L: ADF (Auto Document Feeder) Load a document here. The documents loaded in the document tray are scanned automatically one sheet at a time. Loading Documents in the ADF (Auto Document Feeder) M: Document Feeder Cover Open when clearing jammed documents. N: Rear Tray Load paper here.
Loading Envelopes in Rear Tray O: Paper Support Extend to load paper in the rear tray. P: Rear Tray Cover Open to load paper in the rear tray. Q: Feed Slot Cover Prevents anything from falling into the feed slot. Open it to slide the paper guides, and close it before printing. R: Paper Guides Align with both sides of the paper stack. S: Document Output Slot Documents scanned from the ADF are delivered here. T: Document Tray Open to load a document in the ADF.
Rear View A: Wired LAN Connector Plug in the LAN cable to connect the printer to a LAN. B: USB Port Plug in the USB cable to connect the printer with a computer. C: Power Cord Connector Plug in the supplied power cord. D: Transport Unit Cover Open when removing jammed paper. E: Rear Cover Detach when removing jammed paper. Important • Do not touch the metal casing. • Do not plug in or unplug the USB cable while the printer is printing or scanning with the computer. This can cause trouble.
Inside View A: Scanning Unit / Cover Scans originals. Also, lift and open it to replace an ink tank or to remove jammed paper inside the printer. B: Print Head Holder The print head is pre-installed. Note • For details on replacing an ink tank, see Replacing Ink Tanks.
Operation Panel A: ON button/ON lamp Turns the power on or off. Lights after flashing when the power is turned on. Before turning on the power, make sure that the document cover is closed. B: Touch Screen Displays messages, menu items, and the operational status. Directly touch the screen lightly with your finger tip to select a menu item or displayed button. You can also preview photos on a memory card before printing.
Power Supply Checking that Power Is On Turning the Printer On and Off Checking the Power Plug/Power Cord Unplugging the Printer 199
Checking that Power Is On The ON lamp is lit when the printer is turned on. Even if the touch screen is off, if the ON lamp is lit, the printer is on. Note • It may take a while for the printer to start printing immediately after you turn on the printer. • The touch screen display will turn off if the printer is not operated for about 10 minutes. To restore the display, touch the touch screen. The print operation from a computer can also restore the display.
Turning the Printer On and Off Turning on the printer 1. Press the ON button to turn on the printer. The ON lamp flashes and then remains lit. Confirming that the Power Is On Note • It may take a while for the printer to start printing immediately after you turn on the printer. • If an error message is displayed on the touch screen, see An Error Occurs. • You can set the printer to automatically turn on when a print or scan operation is performed from a computer connected by USB cable or wireless network.
Important • When you unplug the power cord after turning off the printer, be sure to confirm that the ON lamp is off. Note • When pressing the ON button, a confirmation screen to retract the paper output tray on the touch screen. If you want to retract the paper output tray, select Yes. • You can set the printer to automatically turn off when no operations are performed or no print jobs are sent to the printer for a certain interval. This feature is set to on by default.
Checking the Power Plug/Power Cord Unplug the power cord once a month to confirm that the power plug/power cord does not have anything unusual described below. • The power plug/power cord is hot. • The power plug/power cord is rusty. • The power plug/power cord is bent. • The power plug/power cord is worn. • The power plug/power cord is split. Caution • If you find anything unusual with the power plug/power cord described above, unplug the power cord and call for service.
Unplugging the Printer To unplug the power cord, follow the procedure below. Important • When you unplug the power cord, press the ON button, then confirm that the ON lamp is off. Unplugging the power cord while the ON lamp is lit or flashing may cause drying or clogging of the print head and print quality may be reduced. 1. Press the ON button to turn the printer off. 2. Confirm that the ON lamp is off. 3. Unplug the power cord.
Using the Operation Panel The operation panel consists of the ON button (A) and touch screen (B). Touch the HOME screen on the touch screen with your finger tip to select menus for copying, scanning, and other functions. Operations on the HOME Screen A: ON button B: Touch Screen Basic Operation of the touch screen Icons on Touch Screen Basic Operation of the touch screen Touch the touch screen lightly with your finger tip or move your finger to access various functions or settings.
Touch Touch lightly with your finger tip. To move forward (or go back) menus or photos continuously, keep touching the forward (or back) mark. Flick Flick your finger on the screen up, down, left, or right. Use to switch menus or move forward or backward through photos. Drag While lightly touching the screen, move your finger up, down, left, or right. Use to view lists of items or move sliders.
Operations on the HOME Screen Display the menu screen or the settings screen from the HOME screen. C: Basic menu Select to copy or scan using the operation panel. After selecting a basic menu, the particular menus are displayed. D: Network Displays the current network status. Select to display the basic network information or to change the network settings. The icon differs depending on the network of use or the network status. Wi-Fi is enabled and the printer is connected to the wireless router.
(Signal strength: 50 % or less): The problem such as the printer cannot print may occur. Place the printer near the wireless router. Wi-Fi is enabled but the printer is not connected to the wireless router. Wired LAN is enabled. Wireless Direct is enabled. Wi-Fi and Wired LAN are disabled. E: Wireless connect Select to connect the printer to a smartphone/tablet over Wi-Fi through Easy wireless connect or via Bluetooth. Tap this button to display a confirmation screen for starting a connection.
(HOME) Displays the HOME screen. (Back) Returns the touch screen to the previous screen. Black Starts black & white copying, scanning, etc. Color Starts color copying, scanning, etc. Stop Cancels operation when print, copy, or scan job is in progress.
Changing Settings Changing Printer Settings from Your Computer (Windows) Changing Printer Settings from Your Computer (macOS) Changing Settings from Operation Panel 210
Changing Printer Settings from Your Computer (macOS) Managing the Printer Power Changing the Printer Operation Mode 211
Managing the Printer Power Printer power supply is operated from Remote UI. Energy saving settings Energy saving settings allow you to set Auto power off and Auto power on. Auto power off is the function wherein the printer automatically turns itself off, when data is not sent or the printer remains inactive for a certain period. The Auto power on function automatically turns on the printer when data is received. 1. Selecting Device settings from Remote UI 2. Click Energy saving settings 3.
Changing the Printer Operation Mode If necessary, switch between various modes of printer operation. 1. Check whether the printer is on and select Device settings from Remote UI 2. If necessary, complete the following settings: Print settings - Prevent paper abrasion The printer can increase the gap between the print head and the paper during high-density printing to prevent paper abrasion. Check this check box to prevent paper abrasion.
Changing Settings from Operation Panel Changing Settings from Operation Panel Setting Items on Operation Panel Print settings LAN settings Bluetooth settings PictBridge settings Other device settings Language selection Firmware update Reset setting Feed settings Web service setup ECO settings Quiet setting System information 214
Changing Settings from Operation Panel This section describes the procedure to change the settings in the Device settings screen, taking the steps to specify Extended copy amount as an example. 1. Check that printer is turned on. 2. Select (Setup) on the HOME screen. Using the Operation Panel 3. Select Device settings. The Device settings screen is displayed. 4. Select a setting item to adjust. The setting screen for the selected item is displayed. 5. Select a setting item. 6.
For more on setting items on the operation panel: Setting Items on Operation Panel 216
Setting Items on Operation Panel Items for Printer Other device settings Language selection Web service setup ECO settings Quiet setting Items for Paper/Printing Print settings Bluetooth settings PictBridge settings Feed settings Items for Maintenance/Management LAN settings Firmware update Reset setting System information 217
Print settings • Prevent paper abrasion Use this setting only if the print surface becomes smudged. Important • Be sure to set this back to OFF after printing since it may result in lower printing speed or lower print quality. • Extended copy amount Selects the amount of image that extends off the paper when printing in borderless (full). Slight cropping may occur at the edges since the copied image is enlarged to fill the whole page.
LAN settings Wi-Fi Wireless Direct Wired LAN Wi-Fi When Wi-Fi is selected in the LAN settings screen, the network settings information of the printer when it is connected by Wi-Fi appears in the Wi-Fi setting list screen. To print the LAN settings, select Print details in the LAN settings screen and select Yes. Printing Network Settings Important • The network settings printout contains important information about your network. Handle it with care. The following setting items are displayed.
• Wi-Fi setup Selects the setup method for Wi-Fi connection. ◦ Easy wireless connect Select if you specify the settings of the access point information to the printer directly from a device (e.g. smartphone, or tablet) without operating the wireless router. Follow the on-screen instructions of the connecting device for the setup procedure. ◦ Manual connect Select when you perform settings for Wi-Fi manually using the operation panel of the printer.
Network (SSID)/device name DIRECT-XXXX-TS9500series Password XXXXXXXXXX (10 characters) Wi-Fi security WPA2-PSK(AES) No. of devices connected now XX/XX IPv4 address XXX. XXX. XXX. XXX (12 characters) IPv4 subnet mask XXX. XXX. XXX. XXX (12 characters) IPv4 default gateway XXX. XXX. XXX. XXX (12 characters) IPv6 link-local address XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters) MAC address (Wi-Fi) XXX. XXX. XXX.
Important • The network settings printout contains important information about your network. Handle it with care. The following setting items are displayed. (Some setting items are not displayed depending on the printer settings.) Items Setting Connection Enabled (connected)/Enabled (disconnected)/Disabled IPv4 address XXX. XXX. XXX. XXX (12 characters) IPv4 subnet mask XXX. XXX. XXX. XXX (12 characters) IPv4 default gateway XXX. XXX. XXX.
◦ Enable/disable WSD Selects whether WSD is enabled or disabled. Note • When this setting is enabled, the printer icon is displayed on the Network Explorer in Windows. ◦ Optimize inbound WSD Selecting Enable allows you to receive the WSD printing data faster. ◦ WSD scan from this device Selecting Enable allows you to transfer the scanned data to the computer using WSD. To transfer the scanned data, tap Color.
◦ Enable/disable communication Selecting Enable allows you to print from a PictBridge (Wi-Fi) compliant device. ◦ Timeout setting Specifies the timeout length. • Wired LAN DRX setting Selecting Enable allows you to activate discontinuous reception when the printer is connected to a device compatible with wired LAN. • IPsec settings Selecting Enable allows you to specify the IPsec security.
Other device settings • Date display format Changes the display format of dates when printed. Note • When ON is selected for Print date on the print settings screen in printing from a memory card, the date is printed in the date display format you selected. Setting Items for Photo Printing Using Operation Panel • Read/write attribute Selects whether to allow data to be written onto memory cards from a computer. Important • Remove the memory card before changing this setting.
Note • You can also select this setting by selecting and then selecting Energy saving settings. (Setup) on the HOME screen, selecting ECO, ECO settings • Document removal reminder Selects whether the printer will display the reminder screen in case you forget to remove the original from the platen after scanning. Important • Depending on the type of original or the state of the document cover, forgetting to remove the original may not be detected.
Language selection Changes the language for the messages and menus on the touch screen.
Firmware update You can update the firmware of the printer, check the firmware version, or perform settings of a notification screen, a DNS server and a proxy server. Important • When you use this function, make sure the printer is connected to the Internet. Note • Only Check current version is available when Disable is selected for Enable/disable Wi-Fi of Wi-Fi and also for Enable/disable Wired LAN of Wired LAN in LAN settings. • Install update Performs the firmware update of the printer.
Reset setting You can set the settings back to the default. • Web service setup only Sets the Web service settings back to the default. • LAN settings only Sets the LAN settings back to the default. • Settings only Sets the settings such as the paper size or media type back to the default. • Reset all Sets all settings you made to the printer back to the default. The administrator password specified by Remote UI or IJ Network Device Setup Utility reverts to the default setting.
Feed settings By registering the paper size and the media type loaded on the rear tray or in the cassette, you can prevent the printer from misprinting by displaying the message before printing starts when the paper size or the media type of the loaded paper differs from the print settings.
Web service setup Select this setting item from Web service setup in (Setup). • Web service usage registration/Web service usage cancellation Registers/Deletes Web service usage to use the printer device information to/from PIXMA/MAXIFY Cloud Link. • Web service connection setup The following setting items are available. ◦ Google Cloud Print setup Registers/Deletes the printer to/from Google Cloud Print.
ECO settings This setting allows you to use automatic duplex printing as a default to save paper and to turn on/off the printer automatically to save electricity. Using Power Saving Function Using Duplex Printing Using Power Saving Function Follow the procedure below to use power saving function. 1. Check that printer is turned on. 2. Select (Setup) on the HOME screen. Using the Operation Panel 3. Select ECO. 4. Select Energy saving settings. 5. Check on-screen instructions and select Next. 6.
1. Check that printer is turned on. 2. Select (Setup) on the HOME screen. Using the Operation Panel 3. Select ECO. 4. Select Two-sided printing setting. 5. Specify settings as necessary. A: Select two-sided copying as a default. B: Select two-sided printing of template forms on the printer as a default. Note • When duplex printing is selected, the icon is displayed on the setting items for duplex printing on each print settings screen.
Quiet setting Enables this function on the printer if you want to reduce the operating noise, such as when printing at night. Follow the procedure below to perform setting. 1. Check that printer is turned on. 2. Select (Setup) on the HOME screen. Using the Operation Panel 3. Select Quiet setting. 4. Select Use quiet mode. The confirmation screen is displayed and the icon appears as the Quiet setting menu icon. Activate this setting to reduce the operating noise while printing is in progress.
System information To display this menu, select System information in (Hint). • Current version Displays the current firmware version. • Printer name Displays the printer name currently specified. • Serial number Displays the printer serial number. • MAC address (Wi-Fi) Displays the MAC address for Wi-Fi. • MAC address (Wired LAN) Displays the MAC address for wired LAN. • Root cert. thumbprint (SHA-1) Shows the root certification thumbprint (SHA-1) of the printer.
Specifications General Specifications Printing resolution (dpi) 4800* (horizontal) x 1200 (vertical) * Ink droplets can be placed with a pitch of 1/4800 inch at minimum. Interface USB Port: Hi-Speed USB * LAN Port: Wired LAN: 100BASE-TX / 10BASE-T Wi-Fi: IEEE802.11n / IEEE802.11g / IEEE802.11b Card Slot: Yes * A computer that complies with Hi-Speed USB standard is required. Since the Hi-Speed USB interface is fully upwardly compatible with USB 1.1, it can be used at USB 1.1.
◦ Square 5" x 5" 13 x 13 cm: 0.24 inch (6.0 mm) ◦ Other sizes: 0.14 inch (3.4 mm) * For printable area of envelope, see below. Envelopes Auto duplex printing: • Top margin: 0.20 inch (5.0 mm) • Bottom margin: 0.20 inch (5.0 mm) • Left margin: ◦ Letter: 0.26 inch (6.4 mm) ◦ Other sizes: 0.14 inch (3.4 mm) • Right margin: ◦ Letter: 0.25 inch (6.3 mm) ◦ Other sizes: 0.14 inch (3.
ADF capacity A4 or Letter size: max. 20 sheets (20 lb/75 g /m2 paper), up to 0.08 inch/2 mm in height Legal size: max. 5 sheets (20 lb/75 g /m2 paper), up to 0.02 inch/0.5 mm in height Copy Specifications Multiple copy max. 99 pages Intensity adjustment 9 positions, Auto intensity (AE copy) Reduction / Enlargement 25 % - 400 % (1 % unit) Scan Specifications Scanner driver Windows: TWAIN 1.9 Specification, WIA Maximum scanning size A4/Letter, 8.5" x 11.
WCN (WCN-NET) Easy wireless connect Other Features: Administration password Minimum System Requirements Conform to the operating system's requirements when higher than those given here. Windows Operating System Windows 10, Windows 8.1, Windows 7 SP1 Note: Operation can only be guaranteed on a PC with pre-installed Windows 7 or later. Hard Disk Space 3.0 GB or more Note: For bundled software installation. The necessary amount of hard disk space may be changed without notice.
• Internet connection is required to use Easy-WebPrint EX and/or Easy-PhotoPrint Editor and all the user's guide. • Easy-WebPrint EX: Internet Explorer 8, 9, 10 and 11 (for Windows) is required. • Windows: Some functions may not be available with Windows Media Center. • Windows: The TWAIN driver (ScanGear) is based on the TWAIN 1.9 Specification and requires the Data Source Manager bundled with the operating system. • macOS: For macOS, an internet connection is required during software installation.
Information about Paper Supported Media Types Paper Load Limit Unsupported Media Types Handling Paper 241
Supported Media Types For best results, choose paper designed for how you are printing. A variety of paper for documents as well as photos or illustrations is available from Canon. Use genuine Canon paper to print important photos, when possible. Media Types Genuine Canon paper Note • For warnings on use of the non-printable side, see each product's usage information. • For details on page sizes and media types, access the Canon website. • Genuine Canon paper is not available in some countries or regions.
Note • When printing photos saved on a PictBridge (Wi-Fi) compliant device, you must specify the page size and media type. Printing from Digital Camera Page Sizes You can use the following page sizes. Note • Page sizes and media types the printer supports differ depending on the OS you are using.
• Card 2.17"x3.58" Special sizes Special page sizes must be within the following limits: • rear tray ◦ Minimum size: 2.17 x 3.51 inches (55.0 x 89.0 mm) Maximum size: 8.50 x 26.61 inches (215.9 x 676.0 mm) • cassette ◦ Minimum size: 5.83 x 8.27 inches (148.0 x 210.0 mm) Maximum size: 8.50 x 11.69 inches (215.9 x 297.0 mm) Paper Weight You can use paper in the following weight range.
Paper Load Limit Genuine Canon Paper Paper for printing documents: Media Name Rear Tray Paper Output Tray Cassette Canon Red Label Superior Approx. 100 sheets Approx. 100 sheets Approx. 50 sheets Canon Océ Office Colour Paper Approx. 80 sheets Approx. 80 sheets Approx. 50 sheets High Resolution Paper *1 Approx. 80 sheets (B4: N/A Approx. 20 50 sheets, A3: 20 sheets) sheets Paper for printing photos: Media Name
Paper other than Genuine Canon Paper Common Name Plain Paper (including recycled paper)*1 Rear Tray Approx. 100 sheets Cassette Approx. 100 sheets (Legal, 11" x 17" (28 x 43 cm), A3, B4: 50 sheets) Paper Output Tray Approx.
Unsupported Media Types Do not use the following types of paper. Using such paper will cause not only unsatisfactory results, but also the printer to jam or malfunction.
Handling Paper • Be careful not to rub or scratch the surfaces of any types of paper when handling. • Hold the paper as closely as possible to its edges and try not to touch the printing surface. The print quality may be degraded if the printing surface is smudged with sweat or oil that comes from your hands. • Do not touch the printed surface until the ink is dried. Even when the ink is dried, be careful not to touch the printed surface as much as possible when handling.
Printing Printing from Computer Printing from Smartphone/Tablet Printing Using Operation Panel Printing from Digital Camera Paper Settings 249
Printing from Computer Printing from Application Software (Windows Printer Driver) Printing from Application Software (macOS AirPrint) Printing Using Canon Application Software Printing Using a Web Service 250
Printing from Application Software (macOS AirPrint) Printing Basic Printing on Postcards Adding Printer How to Open Printer Settings Screen Displaying the Printing Status Screen Deleting the Undesired Print Job Removing Printer That Is No Longer Required from List of Printers 251
Printing This printer is compatible with the macOS standard printing system (AirPrint). You can start printing right away after connecting this printer to your Mac without installing any special software. Checking Your Environment First, check your environment.
Note • Click Show Details to switch the setup window to the detailed display. 6. Check print settings Set items such as Paper Size to the appropriate size, as well as Feed From and Media Type from Media & Quality of the pop-up menu. Select Auto Select for Media Type. Remove the Two-Sided check mark if you are not printing on both sides of the paper. Important • An error may occur if the paper size set in the print dialog is different from the paper size set on the printer.
• If printing in A4, A5, JIS B5, or US Letter, set the desired feed position (Main Tray or Rear Tray) from Feed From of the print dialog. If Auto Select is selected in Feed From, the feed position differs depending on Media Type. If Media Type is set to plain paper, it is fed from the cassette (main tray). If set to other types of paper, it is fed from the rear tray. • If printing paper such as photo paper and postcards that cannot be printed on both sides, uncheck the Two-Sided checkbox.
Printing on Postcards This section describes the procedure for printing on postcards. 1. Load postcards in printer 2. Select paper size and paper type from the printer Register Hagaki for paper size from the printer operation panel. Also, register Hagaki, IJ Hagaki, or Hagaki K for paper type, according to your purpose. When you print on the address side, register Hagaki. 3. Select Paper Size and Media Type from the print dialog Select Postcard or Postcard Borderless for Paper Size from the print dialog.
Important • Two-sided printing is not possible for postcards, so remove the Two-Sided check mark. If you print with the Two-Sided check mark on, the printing result may not be as you intended. • You will get cleaner printing if you print the message side first and then print the address side. 5. Click Print The printer prints according to the specified settings.
Adding Printer Procedure for adding printer to your Mac is explained. To re-add a printer that was deleted, open System Preferences -> Printers & Scanners, click + next to the printer list, and then perform the procedure described below. If your printer is connected via USB, and you connect the USB cable to a Mac, the printer is automatically added. The below procedure is not necessary in this case. 1.
How to Open Printer Settings Screen The settings screen of the printer can be displayed from your application software. Opening the Page Setup Dialog Use this procedure to set the page (paper) settings before printing. 1. Select Page Setup... from the File menu of the application software The Page Setup dialog opens. Opening the Print Dialog Use this procedure to set the print settings before printing. 1. Select Print... from the File menu of the application software The Print dialog opens.
Displaying the Printing Status Screen Check the print progress according to the following procedure: 1. Launch the printing status screen • If the print data has been sent to the printer The printing status screen opens automatically. To display the printing status screen, click the (the printer icon) displayed on the Dock. • If the print data has not been sent to the printer Open System Preferences, and select Printers & Scanners.
Deleting the Undesired Print Job If the printer does not start printing, canceled or failed print job data may be remaining. Delete unnecessary print jobs from the print status check screen. 1. Open System Preferences, and select Printers & Scanners 2. Select your model, and then click Open Print Queue... The print status check screen appears. 3. Select the unnecessary print job and click (Delete) The selected print jobs will be deleted.
Removing Printer That Is No Longer Required from List of Printers The printer that is no longer in use can be removed from the list of printers. Before removing the printer, remove the cable connecting the printer and PC. You cannot remove the printer if not logged in as the administrator. For information about an administrative user, see Users & Groups from System Preferences. 1. Open System Preferences, and select Printers & Scanners 2.
Printing Using Canon Application Software Easy-PhotoPrint Editor Guide 262
Printing Using a Web Service Using PIXMA/MAXIFY Cloud Link Printing with Google Cloud Print 263
Printing from Smartphone/Tablet Printing from iPhone/iPad/iPod touch (iOS) Printing from Smartphone/Tablet (Android) Printing from Windows 10 Mobile Device Printing/Scanning with Wireless Direct 264
Printing/Scanning with Wireless Direct You can connect devices (e.g. smartphone, or tablet) to the printer by two methods below. • Wireless connection (connecting devices via a wireless router) • Direct wireless connection (connecting devices using Wireless Direct) This section describes Wireless Direct, which allows you to print or scan by connecting the devices to the printer directly. Follow the procedure below to use Wireless Direct. 1. Preparing the printer.
8. Select ON. The Wireless Direct is enabled and a device can be connected to the printer wirelessly. Note • To show the password, select Show password. To hide the password, select Hide password. • The Wireless Direct setting list screen shows settings for when using the printer with Wireless Direct. Devices detect the printer by Network (SSID)/device name shown on the screen. • The password is required when connecting a device to the printer.
• Depending on the device you are using, entering the password is required to connect a device to the printer via Wi-Fi. Enter the password specified for the printer. • If your Wi-Fi Direct compatible device is set to prioritize using Wi-Fi Direct and it is connecting to the printer, the printer displays a confirmation screen asking if you allow the device to connect to the printer. Make sure the name on the touch screen is the same as that of your wireless communication device and select Yes.
6. Select Settings. 7. Select a setting item. • Change SSID/device name Change the identifier (SSID) for Wireless Direct. The identifier (SSID) is the printer's name (device name) displayed on a Wi-Fi Direct compatible device. Follow the procedure below to change the identifier (SSID). 1. Select the entry field. 2. Enter the identifier (SSID) (up to 32 characters) and select OK. 3. Select OK. Selecting OK finishes specifying the identifier (SSID). Selecting Auto update displays the confirmation screen.
If you want the printer to display the screen to inform you a Wi-Fi Direct compatible device is connecting to the printer, select Yes. Important • To prevent an unauthorized access, we recommend you should not change the setting from the default. 8. Tap (HOME). The HOME screen is displayed. Note • If you change the Wireless Direct setting of the printer, also change the wireless router setting of the device.
Printing Photo Data Printing Photographs Saved on Memory Card Basic Setting Items for Photo Printing Using Operation Panel 270
Printing Photographs Saved on Memory Card You can print the photograph saved on the memory card easily. This section describes the procedure to print the photograph in Select photo print. 1. Check that printer is turned on. 2. Load photo paper. 3. Select Print on the HOME screen. Using the Operation Panel 4. Select Memory card. The memory card print menus are displayed. 5. Select Select photo print. 6. Insert memory card into card slot. The photo selection screen is displayed.
You can print a copy of the displayed photo by tapping Color. • To change the display method, the number of copies, or the print settings: Tap near the bottom of the displayed photo to display menus. A: Total number of copies is displayed When tapping, the Check total no. of copies screen is displayed and you can check the number of copies for each photo. On the Check total no. of copies screen, you can change the number of copies for each photo.
Note • You can specify the number of copies for each photo. Display the photo you want to print and specify the number of copies when the desired photo is displayed. C: Select to switch the photo group. For details: Using Useful Display Functions D: Select to display the Settings screen. You can change the settings of page size, media type, and print quality and so on. For more on the setting items: Setting Items for Photo Printing Using Operation Panel E: Select to display two photos side-by-side.
F: Select to zoom in on the photo. For details: Using Useful Display Functions G: Select display photo with specifying the date (last modified date of data). For details: Using Useful Display Functions H: Select to display the multiple photos at once. For more on the display method: Using Useful Display Functions 8. Tap Color. The printer starts printing. Note • Tap Stop to cancel printing.
• While processing the print job, you can add the print job (Reserve photo print). Adding Print Job Adding Print Job You can add the print job (Reserve photo print) while printing photos. Follow the procedure below to add the print job. 1. Flick photo while printing to select next photo. Note • While you select the photo, the printer prints the reserved photos. • The reserved photo icon appears on the photo included in the print job. 2. Specify number of copies and print settings for each photo.
Setting Items for Photo Printing Using Operation Panel You can specify the setting of page size, media type, photo fix and so on to print the photos saved on the memory card. Print Settings Screen How to display the print settings screen varies with the print menu. • In Select photo print or Slide show: The following screen is displayed by selecting Settings. • In Trimming print: The following screen is displayed before printing.
on the touch screen. In this case, select message and change the setting. on the upper left on the touch screen to check the • The settings of the page size, media type, etc. are retained even if another print menu is selected or the printer is turned off. You can specify the following setting items. • Paper src Select a paper source (Rear tray/Cassette/Auto) where paper is loaded.
Other device settings 278
Disc Label Printing Copying Label Side of Disc Basic Printing Photo from Memory Card onto Disc Label 279
Copying Label Side of Disc You can copy the label of an existing BD/DVD/CD and print it on a printable disc. Important • You cannot print on 3.15 inches / 8 cm printable discs. • Do not mount the multi-purpose tray until the message prompting you to load the printable disc appears. Doing so can damage the printer. 1. Check that printer is turned on. 2. Select Copy on the HOME screen. Using the Operation Panel 3. Select Disc label. 4. Check message and select OK.
If the print result is blurry, select Bleed-proof. Blurring may be reduced by printing with less ink. 7. Follow on-screen instructions to load copy source BD/DVD/CD on platen and select OK. The print setting confirmation screen is displayed. Important • Be sure to load the copy source BD/DVD/CD with its label side down on the center of the platen. If you load it near the edge of the platen, part of the image may be cut off. 8. Open operation panel until horizontal. 9.
Note • You can see the procedure to set the printable disc by selecting How to set. • For more on setting the printable disc: Placing a Printable Disc 11. Select OK. The printer starts copying. Note • Tap Stop to cancel copying. • After printing, allow the printing surface of the disc to dry naturally. Do not use hairdryers or expose the disc to direct sunlight to dry the ink. Do not touch the printing surface until the ink has dried.
Printing Photo from Memory Card onto Disc Label You can print a photograph saved on a memory card onto the disc label of the printable disc. Important • You cannot print on 3.15 inches / 8 cm printable discs. • Do not mount the multi-purpose tray until the message prompting you to load the printable disc appears. Doing so can damage the printer. 1. Check that printer is turned on. 2. Select Print on the HOME screen. Using the Operation Panel 3. Select Memory card.
A: Specify the outer circle. B: Specify the inner circle. Note • Measure the outer and inner diameters of the printing surface of the printable disc and make sure you set a value smaller than the measured value for the outer diameter, and a value larger than the measured value for the inner diameter. • For information on printable discs, contact their manufacturers. 8. Specify the amount of ink. If the print result is blurry, select Bleed-proof. Blurring may be reduced by printing with less ink. 9.
12. Check message and tap Color. 13. Follow on-screen instructions to set printable disc. Note • You can see the procedure to set the printable disc by selecting How to set. • For more on setting the printable disc: Placing a Printable Disc 14. Select OK. The printer starts printing. Note • Tap Stop to cancel printing. • After printing, allow the printing surface of the disc to dry naturally. Do not use hairdryers or expose the disc to direct sunlight to dry the ink.
Paper Settings By registering the paper size and the media type loaded on the rear tray or in the cassette, you can prevent the printer from misprinting by displaying the message before printing starts when the paper size or the media type of the loaded paper differs from the print settings. Note • The default display setting is different between when you print or copy from the operation panel of the printer, when you print from Smartphone/tablet, when you print from Windows, and when you print from macOS.
• When you insert the cassette: The screen to register the cassette paper information is displayed. If the page size on the touch screen matches the size of the paper loaded in the cassette, select Yes. If not, select Change to change the setting in accordance with the size of the loaded paper. * You can load only plain paper in the cassette.
When you start printing/copying, a message is displayed and the paper setting specified for printing/ copying is shown under the message. Check the message and select Next. When the screen to select the operation is displayed, select one of the operations below. Note • Depending on the setting, the choices below may not be displayed. Print with the loaded paper. Select if you want to print/copy on the paper loaded without changing the paper settings.
Note • If you do not know what paper information to register to the printer, tap screen to select the operation is displayed. (Back) when the • For more on the proper combination of paper settings you can specify by the printer driver (Windows) or on the touch screen: Paper Settings on the Printer Driver and the Printer (Media Type) Paper Settings on the Printer Driver and the Printer (Paper Size) Cancel Cancels printing. Select when you change the paper settings specified for printing/copying.
Copying Making Copies Reducing/Enlarging Copies Basics Two-Sided Copying Collated Copying Special Copy Menu Copying Using Smartphone or Tablet 290
Making Copies This section describes the procedure to copy with Standard copy. 1. Check that printer is turned on. 2. Load paper. 3. Select Copy on the HOME screen. Using the Operation Panel 4. Select Standard copy. The Copy standby screen is displayed. 5. Load original document on platen or in ADF (Auto Document Feeder). 6. Specify settings as necessary. A: The scanning method and copy layout is displayed. Switch the scanning method from the ADF and layout (single-sided/two-sided).
Tap or to specify the number of copies. If you keep touching here, the number scrolls by 10. You can also flick the number to specify. C: Display the print setting items. For more on the setting items: Setting Items for Copying D: Specify the page size and the media type. 7. Tap Color for color copying, or Black for black & white copying. The printer starts copying. Remove the original on the platen or from the document output slot after copying is complete.
Load the original on the platen and tap the same button (Color or Black) as the one which you previously tapped. Important • When you load the original on the platen, move the document cover gently. Note • When Print qlty (print quality) is set High, you cannot add the copying job. • When you add the copying job, the number of copies or the settings such as the page size or media type cannot be changed.
Setting Items for Copying You can change the copy settings such as magnification and intensity. Print Settings Screen Note • For more on the print settings screen or the setting item for Photo copy, see Copying Photos. The following screen is displayed by selecting Settings in the Copy standby screen. Example in Standard copy: Preview When Preview is displayed on the print settings screen, selecting Preview allows you to preview an image of the printout on the preview screen. For details, see below.
Note • Depending on the copy menu, some setting items cannot be selected. This section describes the setting items in Standard copy. The setting item which cannot be selected is displayed grayed out. For more on the setting items for Photo copy, see Copying Photos. • Some settings cannot be specified in combination with the setting of other setting item or the copy menu. If the setting which cannot be specified in combination is selected, screen. In this case, select change the setting.
• Page size Select the page size of the loaded paper. • Type (Media type) Select the media type of the loaded paper. • Print qlty (Print quality) Adjust print quality according to the original. Important • If you use Draft with Type set to Plain paper and the quality is not as good as expected, select Standard or High for Print qlty and try copying again. • Select High for Print qlty to copy in grayscale. Grayscale renders tones in a range of grays instead of black or white. • Layout Select the layout.
Scanning Scanning from Computer (Windows) Scanning from Computer (macOS) Scanning from Operation Panel Scanning Using Smartphone/Tablet 297
Scanning from Computer (macOS) Scanning According to Item Type or Purpose (IJ Scan Utility Lite) IJ Scan Utility Lite Features Scanning Easily (Auto Scan) Basics Scanning Documents and Photos Scanning Tips Positioning Originals (Scanning from Computer) 298
Scanning According to Item Type or Purpose (IJ Scan Utility Lite) IJ Scan Utility Lite Features Scanning Easily (Auto Scan) Basics Scanning Documents and Photos Important • Available functions and settings vary depending on your scanner or printer.
IJ Scan Utility Lite Features Use IJ Scan Utility Lite to scan and save documents, photos, or other items at one time by simply clicking the corresponding icon. Important • The displayed items and available functions vary depending on your scanner or printer. Multiple Scanning Modes Auto allows for one click scanning with default settings for various items. Document will sharpen text in a document or magazine for better readability, and Photo is best suited for scanning photos.
Note • To set the applications to integrate with, see Settings Dialog.
Scanning Easily (Auto Scan) Auto Scan allows for automatic detection of the type of the item placed on the platen or ADF (Auto Document Feeder). Important • This function is not supported depending on your model. • The following types of items may not be scanned correctly. In that case, adjust the cropping frames (selection boxes; scan areas) in the screen displayed by clicking Driver in the IJ Scan Utility Lite main screen, and then scan again.
Scanning Multiple Documents at One Time from the ADF (Auto Document Feeder) 303
Scanning Documents and Photos Scan items placed on the platen with settings suitable for documents or photos. Save documents in formats such as PDF and JPEG, and photos in formats such as JPEG and TIFF. 1. Place the item on the platen. Positioning Originals (Scanning from Computer) 2. Start IJ Scan Utility Lite. 3. To specify the paper size, resolution, PDF settings, etc., click Settings..., and then set each item in the Settings dialog.
Scanning Tips Positioning Originals (Scanning from Computer) 305
Positioning Originals (Scanning from Computer) This section describes how to load originals on the platen or ADF (Auto Document Feeder) for scanning. If items are not placed correctly they may not be scanned correctly. Important • Be sure to observe the following when loading the original on the platen. Failure to observe the following may cause the scanner to malfunction or the platen glass to break. • Do not place any objects weighing 4.4 lb (2.0 kg) or more on the platen glass.
of the platen and the item. Portions placed on the diagonally striped area cannot be scanned. Important • Inkjet All-In-One printer: Important • Large items (such as A4 size photos) that cannot be placed away from the edges/arrow (alignment mark) of the platen may be saved as PDF files. To save in a format other than PDF, scan by specifying the data format.
1. Make sure any original has been removed from platen. 2. Open document tray (A). 3. Slide the paper guides (B) all the way out. 4. Load document with side to scan facing up in document tray. Insert the document until it stops. 5. Adjust document guide (B) to match width of document. Do not slide the document guide too hard against the document. The document may not be fed properly. Note • When scanning duplex documents, place the front sides facing up.
2. Place the item with the side to scan facing the platen, and then align it with the alignment mark. Important • If you open the document cover wide, the scanner may fall over. • Portions placed over (A) (0.094 inch (2.4 mm) from the left edge of the platen) or (B) (0.106 inch (2.7 mm) from the front edge) cannot be scanned. 2. Gently close document cover. While scanning, hold the document cover gently with your hand to keep it closed.
• The item type may not be detected automatically. In that case, specify the item type in IJ Scan Utility and scan.
Scanning Using Smartphone/Tablet Using PIXMA/MAXIFY Cloud Link Printing/Scanning with Wireless Direct 311
Frequently Asked Questions Network Cannot Find Printer on Network Cannot Find Printer while Using Wi-Fi Network Key (Password) Unknown Cannot Print or Connect For other questions about network, click here.
Scanning Problems (Windows) Scanning Problems (macOS) Scan Results Are Unsatisfactory (Windows) Scan Results Are Unsatisfactory (macOS) Cannot Print/Scan from Smartphone/Tablet Cannot Set Correctly (Network) Cannot Find Printer on Check Printer Settings Screen During Setup (Windows) Cannot Find Printer while Using Wi-Fi Cannot Find Printer while Using Wired LAN Printer Suddenly Stopped Working for Some Reason Network Key (Password) Unknown Forgot Administrator Password of Printer Printer Cannot Be Used Afte
Network Settings and Common Problems Here are frequently asked questions on network. Select a connection method you are using, or you want to use.
Printing/Scanning from Smartphone/Tablet Connecting Printer and Wireless Router Using Easy wireless connect Cannot Connect Smartphone/Tablet to Wireless Router Checking Wireless Router Network Name (SSID) for Smartphone/Tablet Setting Up Using Smartphone/Tablet Cannot Print/Scan from Smartphone/Tablet Cannot Find Printer from Smartphone/Tablet while Using Bluetooth Downloading Canon PRINT Inkjet/SELPHY Problems while Using Printer Message Appears on Computer During Setup Printer Prints Slowly No Ink Level A
Cannot Find Printer while Using Wired LAN Detect Same Printer Name Cannot Print or Connect Printer Suddenly Stopped Working for Some Reason Cannot Print or Connect LAN Setting Tips/Changing LAN Settings Forgot Administrator Password of Printer Checking Network Information Restoring to Factory Defaults Default Network Settings Connects to Another Computer via LAN/Changes from USB to LAN Connection Printing Network Settings Reconfiguration Method of LAN Connection/Reconfiguration Method of Wi-Fi Connection Ch
Network Communication Problems Cannot Find Printer on Network Network Connection Problems Other Network Problems 317
Cannot Find Printer on Network While performing printer setup: Cannot Find Printer on Check Printer Settings Screen During Setup (Windows) Cannot Proceed beyond Printer Connection Screen While using printer: Cannot Find Printer while Using Wi-Fi Note • You cannot use the wireless LAN and the wired LAN at the same time.
Cannot Find Printer on Check Printer Settings Screen During Setup (Windows) If the printer cannot be found and the Check Printer Settings screen appears after searching the printer by Automatic search on the Search for Printers screen, click Redetect and search for the printer again by the IP address on the Search for Printers screen. If the printer has not been found after searching it by the IP address, check network settings.
Cannot Find Printer on Check Printer Settings Screen During Wired LAN Setup (Windows)Checking Security Software Settings Cannot Find Printer on Check Printer Settings Screen During Wired LAN Setup (Windows)Checking Router Settings 320
Cannot Find Printer on Check Printer Settings Screen During Wi-Fi Setup (Windows)-Checking Power Status Are printer and network device (router, etc.) turned on? Make sure the printer is turned on. Checking that Power Is On Make sure network device (router, etc.) is turned on. If printer or network device is off: Turn on printer or network device. It may take a while for the printer and network device to become ready for use once they are turned on.
Cannot Find Printer on Check Printer Settings Screen During Wi-Fi Setup (Windows)-Checking PC Network Connection Can you view any web pages on your computer? Make sure the computer and network device (router, etc.) are configured and the computer is connected to the network. If you cannot view any web pages: Click Cancel on the Check Printer Settings screen to cancel to set up the network communication. After that, configure the computer and network device.
Cannot Find Printer on Check Printer Settings Screen During Wi-Fi Setup (Windows)-Checking Printer's Wi-Fi Settings Is printer set to allow wireless communication? Make sure the or icon is displayed on the touch screen. If icon is not displayed: The printer is not set to allow wireless communication. Turn on wireless communication on the printer.
Cannot Find Printer on Check Printer Settings Screen During Wi-Fi Setup (Windows)-Checking Wi-Fi Environment Is the printer connected to the wireless router? Use the icon on the touch screen to make sure the printer is connected to the wireless router. If is displayed: • Check wireless router configuration. After checking the wireless router setting, make sure the printer is not placed far away from the wireless router. The printer can be up to 50 m (164 ft) from the wireless router indoors.
Important • Note that some wireless routers distinguish network names (SSIDs) by the last alphanumeric character according to their bandwidth (2.4 GHz or 5 GHz) or purpose (for computer or game machine). Check the network name (SSID) of the wireless router for the printer on the touch screen. Select (Setup) icon, Device settings, LAN settings, and Wi-Fi, and then check Network name (SSID). Note • You can also check Network name (SSID) by selecting the icon on the lower left and selecting Wi-Fi.
Cannot Find Printer on Check Printer Settings Screen During Wi-Fi Setup (Windows)-Checking Printer's IP Address Is printer's IP address specified correctly? If printer's IP address is not specified correctly, the printer may not be found. Make sure whether printer's IP address is not used for another device. To check the printer's IP address, print out the network settings information or use the operation panel to display it. • Display on the touch screen. LAN settings • Print the network settings.
Cannot Find Printer on Check Printer Settings Screen During Wi-Fi Setup (Windows)-Checking Security Software Settings Disable block in firewall function temporarily. The firewall of your security software or operation system for computer may limit communication between the printer and your computer. Check the firewall setting of your security software or operation system or the message shown on your computer and disable block temporarily.
Cannot Find Printer on Check Printer Settings Screen During Wi-Fi Setup (Windows)-Checking Wireless Router Settings Check wireless router settings. Check wireless router network connection settings, such as IP address filtering, MAC address filtering, encryption key, and DHCP function. Make sure the same radio channel is assigned to the printer and the wireless router. To check the settings of the wireless router, see the instruction manual supplied with the wireless router or contact the manufacturer.
Cannot Find Printer on Check Printer Settings Screen During Wired LAN Setup (Windows)-Checking LAN Cable and Router Is LAN cable connected, and are printer and router on? Make sure the LAN cable is connected. Make sure the printer is turned on. Checking that Power Is On Make sure the router is turned on. If LAN cable is connected and printer or network device is off: Turn on printer or network device. It may take a while for the printer and network device to become ready for use once they are turned on.
Cannot Find Printer on Check Printer Settings Screen During Wired LAN Setup (Windows)-Checking PC Network Connection Can you view any web pages on your computer? Make sure the computer and network device (router, etc.) are configured and the computer is connected to the network. If you cannot view any web pages: Click Cancel on the Check Printer Settings screen to cancel to set up the network communication. After that, configure the computer and network device.
Cannot Find Printer on Check Printer Settings Screen During Wired LAN Setup (Windows)-Checking Printer's Wired LAN Settings Is printer set to allow wired communication? Make sure the icon is displayed on the touch screen. If icon is not displayed: The printer is not set to allow wired communication. Turn on wired communication on the printer. Once you have turned on wired communication, redo the network communication setup from the beginning.
Cannot Find Printer on Check Printer Settings Screen During Wired LAN Setup (Windows)-Checking Printer's IP Address Is printer's IP address specified correctly? If printer's IP address is not specified correctly, the printer may not be found. Make sure whether printer's IP address is not used for another device. To check the printer's IP Address, print out the network settings information or use the operation panel to display it. • Display on the touch screen. LAN settings • Print the network settings.
Cannot Find Printer on Check Printer Settings Screen During Wired LAN Setup (Windows)-Checking Security Software Settings Disable block in firewall function temporarily. The firewall of your security software or operation system for computer may limit communication between the printer and your computer. Check the firewall setting of your security software or operation system or the message shown on your computer and disable block temporarily.
Cannot Find Printer on Check Printer Settings Screen During Wired LAN Setup (Windows)-Checking Router Settings Check router settings. Check router network connection settings such as IP address filtering, MAC address filtering, and DHCP function. For more on checking the settings of the router, refer to the instruction manual supplied with the router or contact its manufacturer. After checking the router settings, click Redetect on the Check Printer Settings screen to redetect the printer.
Cannot Proceed beyond Printer Connection Screen If you cannot proceed beyond the Printer Connection screen, check the following. Check1 Make sure USB cable is securely plugged in to printer and computer. Connect the printer and the computer using a USB cable as the illustration below. The USB port is located at the back of the printer. Important • Connect the "Type-B" terminal to the printer with the notched side facing UP. For details, refer to the instruction manual supplied with the USB cable.
4. Turn off printer. 5. Restart computer. 6. Make sure you have no application software running. 7. Perform setup on web page. Note • You can use the Setup CD-ROM to redo setup. • For macOS: 1. Click Next. The screen telling you that installation has not been completed appears. 2. Click No. The screen to select application software to install appears. 3. Click Back to Top. 4. Click Exit on Start Setup screen. 5. Turn off printer. 6. Restart computer. 7.
Cannot Find Printer while Using Wi-Fi Make sure printer is turned on. Check1 If not, make sure the printer is securely plugged in and press ON button to turn on. The ON lamp flashes while the printer is initializing. Wait until the ON lamp stops flashing and remains lit. Check the Check2 If the (Network status) icon on the touch screen. icon is displayed, or only the icon is displayed, wireless LAN is disabled.
Note • Use 2.4 GHz frequency band to connect to a wireless router. Match the network name (SSID) set for the printer with that for 2.4 GHz frequency band of the wireless router. To check the network name (SSID) set for the printer, print out the network setting information. Printing Network Settings Note • IJ Network Device Setup Utility allows you to diagnose and repair the network status. Select the link below to download IJ Network Device Setup Utility and install it.
Starting Up IJ Network Device Setup Utility • For macOS: Starting Up IJ Network Device Setup Utility Check7 Make sure the computer is connected to the wireless router. For more on how to check the computer settings or connection status, see your computer instruction manual or contact its manufacturer. Note • If you use a smartphone or tablet, make sure the Wi-Fi is enabled on the device.
Network Connection Problems Printer Suddenly Stopped Working for Some Reason Network Key (Password) Unknown Printer Cannot Be Used After Replacing Wireless Router or Changed Router Settings 340
Printer Suddenly Stopped Working for Some Reason Cannot Connect to a Printer after Network Configuration Changes Cannot Connect to a Printer via Wireless LAN (Wi-Fi) Cannot Connect to a Printer through Wireless Direct Cannot Connect to a Printer via Wired LAN Cannot Print/Scan through Network Cannot Connect to a Printer after Network Configuration Changes It may take a while for the computer to obtain an IP address, or you may need to restart your computer.
To check the settings of the wireless router, refer to the instruction manual provided with it or contact its manufacturer. Note • Use 2.4 GHz frequency band to connect to a wireless router. Match the network name (SSID) set for the printer with that for 2.4 GHz frequency band of the wireless router. To check the current network settings of the printer, print out the network setting information.
See below for starting up IJ Network Device Setup Utility. • For Windows: Starting Up IJ Network Device Setup Utility • For macOS: Starting Up IJ Network Device Setup Utility Check7 Make sure of the Wi-Fi channel numbers used for your computer. You need to have the same Wi-Fi channel number that you are using for the wireless router as your computer. It is normally set in the way that you can use all the Wi-Fi channels.
Turn on the printer or devices. If the power is already turned on, cycle the power switch. Check2 Is the icon displayed on the touch screen? If not, Wireless Direct is disabled. Turn on Wireless Direct. Check3 Check the settings of your device (smartphone/tablet). Make sure Wi-Fi is enabled on your device. For details, refer to your device's instruction manual. Check4 Make sure printer is selected as connection for device (e.g. smartphone or tablet).
Cannot Connect to a Printer via Wired LAN Check1 Make sure the printer is turned on. Check2 Make sure the LAN cable is connected properly. Make sure the printer is connected to the router with the LAN cable. If the LAN cable is loose, connect the cable properly. If the LAN cable is connected to the WAN side of the router, connect the cable to the LAN side of the router. If the problem is not resolved, redo setup. • For Windows: Perform setup using the Setup CD-ROM or from the web page.
Network Key (Password) Unknown WPA/WPA2 or WEP Key Set for Wireless Router Unknown, Cannot Connect Setting an Encryption Key WPA/WPA2 or WEP Key Set for Wireless Router Unknown, Cannot Connect For more on setting up a wireless router, see the instruction manual provided with the wireless router or contact its manufacturer. Make sure your computer can communicate with the wireless router. Note • IJ Network Device Setup Utility allows you to diagnose and repair the network status.
Selecting WPA, WPA2, or WPA/WPA2 is recommended for security reason. If your wireless router is compatible with WPA/WPA2, you can also use WPA2 or WPA. • Using WPA/WPA2 (Windows) The authentication method, Wi-Fi password, and dynamic encryption type must be identical among the wireless router, the printer, and your computer. Enter the Wi-Fi password configured on the wireless router. Either TKIP (basic encryption) or AES (secure encryption) is selected automatically as the dynamic encryption method.
Printer Cannot Be Used After Replacing Wireless Router or Changed Router Settings When you replace a wireless router, redo the network setup for the printer according to the replaced one. • For Windows: Perform setup using the Setup CD-ROM or from the web page. • For macOS: Perform setup from the web page. Note • IJ Network Device Setup Utility allows you to diagnose and repair the network status. Select the link below to download IJ Network Device Setup Utility and install it.
If filtering MAC addresses or IP addresses at wireless router, check that MAC addresses or IP addresses for computer, network device, and printer are registered. Check2 Check3 If using WPA/WPA2 key or a password, make sure encryption key for computer, network device, and printer matches key set for wireless router. The length or format of the Wi-Fi password and authentication method must be identical among the wireless router, the printer, and your computer. For details, see Setting an Encryption Key.
Other Network Problems Checking Network Information Restoring to Factory Defaults 350
Checking Network Information Checking Printer IP Address or MAC Address Checking Computer IP Address or MAC Address Checking Communication Between the Computer, the Printer, and the Wireless Router Checking Network Setting Information Checking Printer IP Address or MAC Address To check the printer's IP Address or MAC address, print out the network settings information or use the operation panel to display it. • Display on the touch screen. LAN settings • Print the network settings.
2. Make sure network interface used by computer is selected, and then click Advanced. When you are using Wi-Fi on your computer, make sure Wi-Fi is selected as network interface. When you are using wired LAN, make sure Ethernet is selected. 3. Click TCP/IP to check the IP address, or click Hardware to check the MAC address. Checking Communication Between the Computer, the Printer, and the Wireless Router Perform a ping test to check if communication is taking place. • For Windows: 1.
5. Click Ping. "XXX.XXX.XXX.XXX" is the IP address of the target device. A message such as the following appears. 64 bytes from XXX.XXX.XXX.XXX: icmp_seq=0 ttl=64 time=3.394 ms 64 bytes from XXX.XXX.XXX.XXX: icmp_seq=1 ttl=64 time=1.786 ms 64 bytes from XXX.XXX.XXX.XXX: icmp_seq=2 ttl=64 time=1.739 ms --- XXX.XXX.XXX.XXX ping statistics --3 packets transmitted, 3 packets received, 0% packet loss If packet loss is 100%, communication is not taking place.
Restoring to Factory Defaults Important • For Windows: Initialization erases all network settings on the printer, making printing or scanning operation from a computer over a network impossible. To use the printer over a network again after restoring it to the factory defaults, redo setup using the Setup CD-ROM or from the web page. • For macOS: Initialization erases all network settings on the printer, making printing or scanning operation from a computer over a network impossible.
Problems while Printing/Scanning from Smartphone/Tablet Cannot Print/Scan from Smartphone/Tablet 355
Cannot Print/Scan from Smartphone/Tablet If you cannot print/scan from your smartphone/tablet, it is possible that your smartphone/tablet cannot communicate with the printer. Check the cause of your problem according to the connection method.
To check the settings of the wireless router, refer to the instruction manual provided with it or contact its manufacturer. To check the current network settings of the printer, print out the network setting information. Printing Network Settings Note • IJ Network Device Setup Utility allows you to diagnose and repair the network status. Select the link below to download IJ Network Device Setup Utility and install it.
Note • IJ Network Device Setup Utility allows you to diagnose and repair the network status. Select the link below to download IJ Network Device Setup Utility and install it. Checking Printer Connection Status Using IJ Network Device Setup Utility See below for starting up IJ Network Device Setup Utility.
Printing Network Settings Check5 Have you entered the proper password specified for the Wireless Direct? To check the password specified for the printer, display it using the operation panel of the printer or print out the network setting information of the printer. • Display on the touch screen. LAN settings • Print the network settings. Printing Network Settings Check6 Make sure the printer is not placed too far away from the device.
Printing Problems Printer Does Not Print Ink Does Not Come Out Paper Does Not Feed Properly/"No Paper" Error Cannot Print on the Disc Label Printout Results Are Unsatisfactory 360
Printer Does Not Print Make sure printer is turned on. Check1 If not, make sure the printer is securely plugged in and press ON button to turn on. The ON lamp flashes while the printer is initializing. Wait until the ON lamp stops flashing and remains lit. Note • If you are printing large data such as photos or other graphics, printing may take longer to start. The ON lamp flashes while the computer is processing data and sending it to the printer. Wait until printing starts.
Changing the Printer Operation Mode (macOS) Check4 If printing from a computer, delete jobs stuck in print queue. • For Windows: Deleting the Undesired Print Job • For macOS: Deleting the Undesired Print Job Check5 Make sure that the paper output tray is at the normal print position. When you do not use the multi-purpose tray, pull the paper output tray out to the front side until it stops and select OK on the touch screen.
• After printing is completed, select Off for Prevention of Print Data Loss. Check8 If printing from a computer, restart the computer. Restart the computer and try printing again.
Ink Does Not Come Out Check1 Make sure of the estimated ink levels in the ink tanks. Check the ink status on the touch screen. Checking Ink Status on the Touch Screen Check2 Are the orange tape and plastic wrap still on the ink tank? Make sure all the protective plastic wrap is peeled off to expose the Y-vent area, as shown below (A). If the orange tape remains on the ink tank (B), peel it off.
Paper Does Not Feed Properly/"No Paper" Error Check1 Make sure paper is loaded. Loading Paper Check2 When loading paper, consider the following. • When loading two or more sheets of paper, align the edges of the sheets before loading the paper. • When loading two or more sheets of paper, make sure the paper stack does not exceed the paper load limit.
If the paper tears in the rear tray, see List of Support Code for Error (Paper Jams) to remove it. If there are any foreign objects in the rear tray, be sure to turn off the printer, unplug it from the power supply, then remove the foreign object. Note • If the feed slot cover is opened, close it slowly. Check7 Clean paper feed roller. Cleaning Paper Feed Rollers Note • Cleaning the paper feed roller abrades it, so do this only when necessary.
Check9 Are transport unit cover and rear cover attached properly? See Rear View for the positions of the transport unit cover and the rear cover. If the measures above do not solve the problem, contact your nearest Canon service center to request a repair.
Cannot Print on the Disc Label Disc Label Printing Does Not Start Multi-Purpose Tray Does Not Feed Properly Multi-Purpose Tray Jammed Disc Label Printing Does Not Start Check1 Is multi-purpose tray placed properly? Place the multi-purpose tray properly again and tap OK on the touch screen. Use the multi-purpose tray supplied with this printer. For more on placing the multi-purpose tray, see Placing a Printable Disc.
Multi-Purpose Tray Jammed Pull out the multi-purpose tray gently. If the multi-purpose tray cannot be pulled out, cycle the power switch. The multi-purpose tray will automatically be ejected. When the multi-purpose tray is pulled out, place the multi-purpose tray again and retry printing. For more on placing the multi-purpose tray, see Placing a Printable Disc. If the multi-purpose tray is still jammed, check if there is a problem with the printable disc.
Printout Results Are Unsatisfactory If the print results are unsatisfactory due to white streaks, misaligned/distorted lines, or uneven colors, check the paper and print quality settings first. Do page size and media type settings match size and type of loaded paper? Check1 If these settings do not match, it is not possible to obtain the proper result. If you are printing a photograph or an illustration, an incorrect paper type setting may reduce the quality of the printout color.
This setting cannot be made on the PictBridge (Wi-Fi) compliant device. Check3 If problem is not resolved, check also the sections below.
Printouts Are Blank/Blurry or Fuzzy/Inaccurate or Bleeding Colors/ Streaks or Lines Printing Is Blurry Colors Are Wrong 372
White Streaks Appear Check1 Check paper and print quality settings. Printout Results Are Unsatisfactory Check2 Check status of ink tanks. Replace ink tank if ink has run out. Replacing Ink Tanks Check3 Are the orange tape and plastic wrap still on the ink tank? Make sure all the protective plastic wrap is peeled off to expose the Y-vent area, as shown below (A). If the orange tape remains on the ink tank (B), peel it off.
Perform print head deep cleaning. If the problem is not resolved after performing print head deep cleaning, turn off the printer and perform print head deep cleaning again 24 hours later. • If problem is not resolved after performing print head deep cleaning twice: If print head deep cleaning does not resolve the problem, the print head may be damaged. Contact your nearest Canon service center to request a repair.
Lines Are Misaligned/Distorted Check1 Check paper and print quality settings. Printout Results Are Unsatisfactory Check2 Perform print head alignment. If printed lines are misaligned/distorted or print results are otherwise unsatisfactory, adjust the print head position. Aligning the Print Head Note • If the problem is not resolved after performing the print head alignment, perform print head alignment manually from your computer.
Paper Is Smudged / Printed Surface Is Scratched Paper Is Smudged Smudged Edges Smudged Surface Printed Surface Is Scratched Check1 Check paper and print quality settings. Printout Results Are Unsatisfactory Check2 Check paper type. Make sure you are using the right paper for what you are printing. Supported Media Types Check3 Correct curl before loading paper. When using Photo Paper Plus Semi-gloss, even if the sheet is curled, load one sheet at a time as it is.
1. Roll up paper in opposite direction to paper curl as shown below. 2. Check that paper is now flat. We recommend printing curl-corrected paper one sheet at a time. Note • Depending on paper type, the paper may smudge or may not feed properly even if it is not curled inward. Follow the instructions below to curl the paper outward up to 0.1 inch / 3 mm (B) in height before printing. This may improve the print result.
1. Check that printer is turned on. 2. Open Canon IJ Printer Assistant Tool. Maintenance Tab Description 3. Select Select Printer... and select printer you are using from pulldown menu and select OK. 4. Select Custom Settings. 5. Select Prevent paper abrasion check box and click OK. ◦ For macOS: Adjust the setting to prevent paper abrasion from Remote UI. Opening Remote UI for Maintenance If brightness is set low, increase brightness setting and try printing again.
Note • Cleaning the paper feed roller abrades it, so do this only when necessary. Is inside of printer dirty? Check8 During duplex printing, ink may stain the inside of the printer, smudging the printout. Perform bottom plate cleaning to clean inside of printer. Cleaning Inside the Printer (Bottom Plate Cleaning) Note • To prevent staining inside the printer, be sure to set the correct paper size. Check9 Set longer ink drying time.
Vertical Line Next to Image Check Is loaded paper size correct? If the loaded paper is larger than the size you specified, a vertical line may appear in the margin. Set the paper size to match the loaded paper. Printout Results Are Unsatisfactory Note • The direction of the vertical line pattern may vary depending on the image data or the print setting. • This printer performs automatic cleaning when necessary to keep printouts clean. A small amount of ink is ejected for cleaning.
Scanning Problems (macOS) Scanning Problems 381
Scanning Problems Scanner Does Not Work Scanner Driver Does Not Start 382
Scanner Does Not Work Check 1 Check that your scanner or printer is turned on. Check 2 With network connection, check the connection status and reconnect as needed. Check 3 With USB connection, connect the USB cable to a different USB port on the computer. If the USB cable is connected to a USB hub, remove it from the USB hub and connect it to a USB port on the computer. Check 4 Check 5 Restart the computer.
Scanner Driver Does Not Start Check 1 Make sure the application software supports AirPrint. Check 2 Select your scanner or printer on the application's menu. Note • The operation may differ depending on the application. Scan and save images with IJ Scan Utility Lite and open the files in your application. Check 3 Check 4 Your scanner may be locked. (Personal scanners only) If IJ Scan Utility Lite or the application is running, exit it.
Mechanical Problems Printer Does Not Turn On Printer Turns Off Unexpectedly or Repeatedly USB Connection Problems Cannot Communicate with Printer via USB Wrong Language Appears in Touch Screen 385
Printer Does Not Turn On Check1 Press ON button. Check2 Make sure power plug is securely connected to printer, and then turn on again. Check3 Unplug printer, leave it for at least 2 minutes, and then plug it back in and turn on again. If this does not solve the problem, contact your nearest Canon service center to request a repair.
Printer Turns Off Unexpectedly or Repeatedly Check If printer is set to turn off automatically after a certain time, disable this setting. If you have set the printer to turn off automatically after a specified time, the power will shut off by itself once that time has elapsed. • To disable the setting from the operation panel: 1. Check that printer is turned on. 2. Select (Setup) on Home screen. 3. Select ECO. 4. Select Energy saving settings. 5. Check displayed message and select Next. 6.
4. Select Disable for Auto Power Off. 5. Select OK. 6. Select OK on the displayed screen. The setting to shut off the power automatically is disabled. Note • Refer to below to disable the setting from ScanGear (scanner driver).
USB Connection Problems Printing or Scanning Is Slow/Hi-Speed USB Connection Does Not Work/"This device can perform faster" Message Appears (Windows) If your system environment does not support Hi-Speed USB, the printer operates at the slower speed of USB 1.1. In this case, the printer works properly but printing or scanning speed may slow down due to the communication speed. Check Check following to make sure your system environment supports Hi-Speed USB connection.
Cannot Communicate with Printer via USB Check1 Make sure printer is turned on. Check2 Connect USB cable properly. As the illustration below, the USB port is at the back of the printer. Important • Connect the "Type-B" terminal to the printer with the notched side facing UP. For details, refer to the instruction manual supplied with the USB cable. Make sure Enable bidirectional support is selected in the Ports sheet of the properties dialog box of the printer driver.
Wrong Language Appears in Touch Screen Follow the instructions below to select your language. 1. Press HOME button and wait a little. 2. Select (Setup) icon. Using the Operation Panel 3. Select . 4. Select sixth setting item from top. 5. Select a language for touch screen. 6. Select button on lower left.
Installation and Download Problems Failed to MP Drivers Installation (Windows) Updating MP Drivers in Network Environment (Windows) 392
Failed to MP Drivers Installation (Windows) • If installation does not start when you insert Setup CD-ROM: Follow the instructions below to start the installation. 1. Make the following settings. ◦ In Windows 10, click Start > File Explorer, and then click This PC from list on left. ◦ In Windows 8.1, select Explorer icon in Taskbar on Desktop, and then select This PC from list on left. ◦ In Windows 7, click Start, and then click Computer. 2. Double-click the CD-ROM icon in the window that appears.
• If you cannot get past the Printer Connection screen: Cannot Proceed beyond Printer Connection Screen • Other cases: Reinstall the MP Drivers. If the MP Drivers were not installed correctly, uninstall the MP Drivers, restart your computer, and then reinstall the MP Drivers. Deleting the Unnecessary MP Drivers Reinstall the MP Drivers with the Setup CD-ROM or install them from the Canon website.
Updating MP Drivers in Network Environment (Windows) Download the latest MP Drivers. Download the latest MP Drivers for your model on the download page of the Canon website. Uninstall the existing MP Drivers and follow the installation instructions to install the latest MP Drivers that you downloaded. In the connection method selection screen, select Use the printer with Wi-Fi connection or Use the printer with wired LAN connection according to the connection method you use.
Errors and Messages An Error Occurs Message (Support Code) Appears 396
An Error Occurs If an error occurs in printing, for example if the paper runs out or jams, a troubleshooting message appears automatically. Take the appropriate action described in the message. When an error occurs, a message appears on the computer, or an error code appears on the printer. For some errors, a support code (error number) appears on the computer screen.
Message (Support Code) Appears This section describes some of the errors and messages that may appear. Note • A support code (error number) is displayed on the computer for some errors. For details on errors that have support code, see List of Support Code for Error. If a message appears on the touch screen, see below. Message Appears on Touch Screen If a message appears on the computer, see below.
Error Regarding Power Cord Being Unplugged Is Displayed (Windows) The printer may have been unplugged while it was on. Check the error message that appears on the computer and click OK. The printer starts printing. See Unplugging the Printer for unplugging the power cord. Writing Error/Output Error/Communication Error (Windows) Check1 If the ON lamp is off, make sure printer is plugged in and turn on. The ON lamp flashes while the printer is initializing.
3. Click General tab and check for a device problem. If a device error is shown, see Windows Help to resolve it. Other Error Messages (Windows) Check If an error message appears outside printer status monitor, check the following: • "Could not spool successfully due to insufficient disk space" Delete any unnecessary files to increase the amount of free space on the disk. • "Could not spool successfully due to insufficient memory" Close other applications to increase the available memory.
List of Support Code for Error Support code appears on the touch screen and your computer screen when errors occur. A "support code" is an error number, and appears along with an error message. When an error occurs, check the support code displayed on the touch screen and computer screen and take the appropriate action in response.
• 5000 to 5ZZZ 5011 5012 5040 5050 5100 5200 520E 5400 5700 5B00 5B01 5C02 • 6000 to 6ZZZ 6000 6001 6004 6500 6502 6800 6801 6830 6831 6832 6833 6900 6901 6902 6910 6911 6920 6921 6930 6931 6932 6933 6934 6935 6936 6937 6938 6940 6941 6942 6943 6944 6945 6946 6951 6A80 6A81 6D01 • 7000 to 7ZZZ 7500 7600 7700 7800 • 8000 to 8ZZZ 8300 • A000 to ZZZZ C000 For paper jam support codes, see also List of Support Code for Error (Paper Jams).
List of Support Code for Error (Paper Jams) If paper jams, remove it following the appropriate procedure as shown below.
1300 Cause Paper is jammed when feeding paper from rear tray. What to Do If the paper fed from the rear tray is jammed, remove the jammed paper from the paper output slot or from the rear tray following the instructions below. 1. Slowly pull out paper, either from paper output slot or from rear tray, whichever is easier. Hold the paper with both hands, and pull it out slowly so as not to tear it. Note • If you cannot pull out the paper, turn the printer back on without pulling forcibly.
Note • When reloading the paper, make sure you are using suitable paper and loading it correctly. • We recommend using paper sizes other than A5 to print documents with photos or graphics. A5 paper may curl and jam as it leaves the printer. If the measures above do not solve the problem, contact your nearest Canon service center to request a repair.
1303 Cause Paper is jammed when feeding paper from cassette. What to Do 1. Remove jammed paper. • If the paper is jammed at the paper output slot: 1300 • If the paper is jammed inside the printer: Paper Is Jammed inside Printer • If the paper is jammed at the feeder of the cassette: Pull out the cassette, and then remove the paper slowly with both hands. • If none of the above is applied, see Removing Jammed Paper from Rear Side to open the rear cover and to remove the paper. 2.
1304 Cause Paper is jammed when performing automatic duplex printing. What to Do 1. Remove jammed paper. • If the paper is jammed at the paper output slot: 1300 • If the paper is jammed inside the printer: Paper Is Jammed inside Printer • If the paper is jammed at the feeder of the cassette: Pull out the cassette, and then remove the paper slowly with both hands. • If none of the above is applied, see Removing Jammed Paper from Rear Side to open the rear cover and to remove the paper. 2.
1313 Cause Paper is jammed as printer pulled in printed paper. What to Do If the paper is jammed as the printer pulled in the printed paper, try to remove the paper from the following locations. • Paper output slot 1300 • Inside of the printer Paper Is Jammed inside Printer If the measures above do not solve the problem, see Removing Jammed Paper from Rear Side to open the rear cover and to remove the paper.
Paper Is Jammed inside Printer If the jammed paper tears and you cannot remove the paper from the paper output slot, or if the jammed paper remains inside the printer, remove the paper following the instructions below. Note • If paper becomes jammed during printing and you need to turn off the printer to remove it, tap Stop to stop the printing before you turn off the printer. 1. Turn off printer and unplug it. 2. Open scanning unit / cover. Important • Do not touch white belt (A).
4. Hold jammed paper firmly in both hands. If the paper is rolled up, pull out it. 5. Slowly pull out paper, so as not to tear it. Pull out the paper at an angle of about 45 degrees. 6. Make sure all jammed paper is removed. If the paper tears when you pull out it, a bit of paper may remain in the printer. Check the following and remove any remaining paper.
• Any paper left under the print head holder? • Any small bits of paper left in the printer? • Any paper left in the left and right empty spaces (B) in the printer? 7. Close scanning unit / cover. All jobs in the print queue are canceled. Redo the printing. Note • When reloading the paper, make sure you are using suitable paper and loading it correctly.
Removing Jammed Paper from Rear Side Note • If paper becomes jammed during printing and you need to turn off the printer to remove it, tap Stop to stop the printing before you turn off the printer. 1. Rotate printer so that rear side of printer faces toward you. 2. Open rear tray cover and then pull up paper support. 3. Detach rear cover. Pull out the rear cover.
4. Slowly pull out paper. Note • Do not touch the inner parts of the printer. If you were not able to remove the paper in this step, detach the transport unit cover and remove the paper by following these steps. 1. Detach transport unit cover. Lift up the transport unit cover and pull out it.
2. Slowly pull out paper. Note • Do not touch the inner parts of the printer. 3. Make sure all jammed paper is removed. 4. Attach transport unit cover. Insert the transport unit cover slowly all the way into printer and take down the transport unit cover. 5. Attach rear cover. Insert the projections of the right side of the rear cover into the printer, and then push the left side of the rear cover until it is closed completely.
If the measures above do not solve the problem, contact your nearest Canon service center to request a repair.
1000 Cause Possible causes include the following. • There is no paper in the rear tray. • Paper is not loaded in the rear tray properly. What to Do Take the corresponding actions below. • Load paper in the rear tray. Loading Paper in the Rear Tray • Align the paper guides with the both edges of the paper when you load paper in the rear tray. • Set paper information for the paper in the rear tray. After carrying out the above measures, select OK on the touch screen.
1003 Cause Possible causes include the following. • There is no paper in the cassette. • Paper is not loaded in the cassette properly. What to Do Take the corresponding actions below. • Load paper in the cassette. Loading Paper in the Cassette • Align the paper guides with the both edges of the paper when you load paper in the cassette. • Set paper information for the paper in the cassette. After carrying out the above measures, select OK on the touch screen.
1200 Cause Scanning unit / cover is open. What to Do Close the scanning unit / cover and wait for a while. Do not close it while you are replacing an ink tank.
1401 Cause Print head may be damaged. What to Do Turn off the printer and turn it back on. If this does not solve the problem, contact your nearest Canon service center to request a repair.
1600 Cause Ink may have run out. What to Do Replacing the ink tank is recommended. If printing is in progress and you want to continue printing, tap OK on the printer with the ink tank installed. Then printing can continue. Replacing the ink tank is recommended after the printing. The printer may be damaged if printing is continued under the ink out condition.
1660 Cause The ink tank cannot be recognized. What to Do Printing cannot be performed because the ink tank is not installed or is not compatible with this printer. Check the ink tank. If you want to cancel printing, tap Stop on the printer.
1688 Cause The ink has run out. What to Do Replace the ink tank and close the scanning unit / cover. Printing under the current condition may damage the printer. If you want to continue printing in this condition, you need to disable the function for detecting the remaining ink level. Touch Stop on the printer for at least 5 seconds, and then release it. With this operation, disabling the function for detecting the remaining ink level is memorized.
1689 Cause Printer detected ink out condition. What to Do Replace the ink tank and close the scanning unit / cover. An ink tank that was once empty is installed. Printing under the ink out condition may damage the printer. If you want to continue printing, you need to disable the function for detecting the remaining ink level. To disable this function, touch Stop on the printer for at least 5 seconds, and then release it.
1700 Cause Ink absorber is almost full. What to Do Select OK on the touch screen to continue printing. Contact your nearest Canon service center to request a repair. Note • In the case of warnings or errors caused by remaining ink levels, the printer cannot print or scan.
1890 Cause Tape for securing print head holder during transportation may still be attached. What to Do Open the scanning unit / cover and make sure the tape for securing the print head holder during transportation has been removed. If the tape is still there, remove it and close the scanning unit / cover. If this does not solve the problem, contact your nearest Canon service center to request a repair.
2110 Cause Paper settings for printing or copying do not match cassette paper information set on printer. Note • See below for the correct correspondence between paper settings made on the printer driver or on the touch screen. Paper Settings on the Printer Driver and the Printer (Media Type) (Windows) Paper Settings on the Printer Driver and the Printer (Paper Size) (Windows) • For copying, make the copy paper settings to match cassette paper information set on the printer.
Select the appropriate action. Note • Depending on settings, some of the options below may not appear. Print with the loaded paper. Select this option to print or copy onto the paper in the cassette without changing the paper settings. For example, if the print or copy paper setting is A5, and cassette paper information is set to A4, the A5 size setting is used to print or copy onto the paper in the cassette. Replace the paper and print Select this option to print after changing the paper in the cassette.
• To change the message view setting when printing or copying using the operation panel of the printer: Feed settings • To change the message view setting when printing using the printer driver: Changing the Printer Operation Mode (Windows) Changing the Printer Operation Mode (macOS) 428
4103 Cause Cannot perform printing with current print settings. What to Do Tap Stop on the touch screen to cancel printing. Then change the print settings and retry printing.
5011 Cause Printer error has occurred. What to Do Turn off printer and unplug it. Plug in the printer again and turn it back on. If this does not solve the problem, contact your nearest Canon service center to request a repair.
5012 Cause Printer error has occurred. What to Do Turn off printer and unplug it. Plug in the printer again and turn it back on. If this does not solve the problem, contact your nearest Canon service center to request a repair.
5100 Cause Printer error has occurred. What to Do Cancel printing and turn off the printer. Check the following: • Make sure print head holder motion is not impeded by tapes for securing the print head holder during transportation, jammed paper, etc. Remove any impediment. • Make sure the ink tanks are properly installed. Press ink tanks until they click into place. Turn the printer back on. If this does not solve the problem, contact your nearest Canon service center to request a repair.
5200 Cause Printer error has occurred. What to Do Turn off printer and unplug it. After a while, plug in the printer again and turn it back on. If this does not solve the problem, contact your nearest Canon service center to request a repair.
5B00 Cause Printer error has occurred. What to Do Contact your nearest Canon service center to request a repair. Note • In the case of warnings or errors caused by remaining ink levels, the printer cannot print or scan.
6000 Cause Printer error has occurred. What to Do If the paper is jammed, remove it depending on the jammed location and cause. List of Support Code for Error (Paper Jams) Turn off printer and unplug it. Plug in the printer again and turn it back on. If this does not solve the problem, contact your nearest Canon service center to request a repair.
C000 Cause Printer error has occurred. What to Do Cancel printing and turn off the printer. Check the following: • Make sure print head holder motion is not impeded by tapes for securing the print head holder during transportation, jammed paper, etc. Remove any impediment. • Make sure the ink tanks are properly installed. Press ink tanks until they click into place. Turn the printer back on. If this does not solve the problem, contact your nearest Canon service center to request a repair.
