Owner's Manual
Table Of Contents
- Instruction Manual
- Highlights of the XF705
- Table of Contents
- Introduction
- Preparations
- Recording
- Recording Video
- Video Configuration: Video Format, System Frequency, Frame Rate, Resolution and Bit Rate
- Changing Main Functions with the FUNC Button
- Shutter Speed
- Gain
- ND Filter
- Aperture
- Gamma Curve and Main Color Settings
- White Balance
- Zooming
- Using Optional Conversion Lenses
- Adjusting the Focus
- Image Stabilization
- Onscreen Markers and Zebra Patterns
- Setting the Time Code
- Setting the User Bit
- Synchronizing with an External Device
- Recording Audio
- Audio Settings and Recorded Audio Channels
- Connecting an External Microphone or External Audio Input Source to the Camcorder
- Setting the Audio Input Type for the INPUT 1/INPUT 2 Terminals
- Selecting the Audio Input Source for Audio Channels
- Adjusting the Audio Recording Level
- Advanced Audio Input Settings
- Monitoring the Audio with Headphones
- Colors Bars/Audio Reference Signal
- Waveform Monitor
- Adding Marks to Clips while Recording
- Using Metadata
- Recording GPS Information (Geotagging)
- Reviewing a Recording
- Special Recording Modes
- Infrared Recording
- Customization
- Playback
- External Connections
- Network Functions
- Photos
- Additional Information
127
Custom Picture Settings
[Noise Reduction]*
[Level] [Automatic],1 (lowest level) to 12 (highest level), [Off]
Reduces the amount of noise that appears in the image.
[Skin Detail]*
[Effect Level] [High], [Middle], [Low], [Off]
[Hue] –16 to 16 (±0)
[Chroma], [Area], [Y Level] 0 to 31 (16)
The camcorder applies a softening filter to areas in the picture with skin tones to give a more
pleasant appearance. By changing these settings, you can determine what areas will be detected as
skin tones. A zebra pattern will appear on the screen over areas of the image that are detected as
having skin tones.
[Effect Level]: Adjusts the level of the filter.
[Hue]: Adjusts the hue for detection of skin tones.
[Chroma]: Adjusts the color saturation for detection of skin tones.
[Area]: Adjusts the color range for detection of skin tones.
[Y Level]: Adjusts the brightness for detection of skin tones.
[White Balance]*
[R Gain], [B Gain] –50 to 50 (±0)
These settings adjust the amount of white balance throughout the whole image by changing the
intensity of red tones ([R gain]) and blue tones ([B Gain]).
[Color Matrix Tuning]*
[Gain] –50 to 50 (±0)
[Phase] –18 to 18 (±0)
These settings adjust the color intensity ([Gain]) and color phase ([Phase]) of the color matrix,
affecting the color tones of the whole image.
[R-G], [R-B], [G-R], [G-B],
[B-R], [B-G]
–50 to 50 (±0)
Each matrix changes the tint of the picture along the color gradations detailed below, affecting the
color tones of the whole image.
[R-G]: cyan/green and red/magenta; [R-B]: cyan/blue and red/yellow;
[G-R]: magenta/red and green/cyan; [G-B]: magenta/blue and green/yellow;
[B-R]: yellow/red and blue/cyan; [B-G]: yellow/green and blue/magenta.
[Color Correction]*
[Select Area] [Area A&B], [Area B], [Area A], [Off]
The camcorder detects areas with certain color characteristics (color phase, chroma, area and Y
level) and corrects them when recording. You can set the color correction for up to two different areas
(A and B) and apply the color correction to either one ([Area A] or [Area B]) or both of them ([Area
A&B]). While color correction is activated, a zebra pattern will appear on the screen over areas of the
image detected as having the characteristics specified for area A or area B.
[Area A Setting Phase],
[Area B Setting Phase]
0 to 31 (0)
These settings determine the color phase of the area to be corrected (A or B, respectively).
[Area A Setting Chroma],
[Area A Setting Area],
[Area A Setting Y Level],
[Area B Setting Chroma],
[Area B Setting Area],
[Area B Setting Y Level]
0 to 31 (16)
These settings determine the following color characteristics of the area to be corrected (A or B,
respectively).
[Area A Setting Chroma], [Area B Setting Chroma]: Color saturation.
[Area A Setting Area], [Area B Setting Area]: Color range.
[Area A Setting Y Level], [Area B Setting Y Level]: Brightness.
[Area A Revision Level],
[Area B Revision Level]
–50 to 50 (±0)
These settings adjust the amount of correction applied to the color saturation in the corrected area
(A or B, respectively).
Menu items Setting options and additional information