Owner's Manual
Table Of Contents
- Instruction Manual
- Highlights of the XF705
- Table of Contents
- Introduction
- Preparations
- Recording
- Recording Video
- Video Configuration: Video Format, System Frequency, Frame Rate, Resolution and Bit Rate
- Changing Main Functions with the FUNC Button
- Shutter Speed
- Gain
- ND Filter
- Aperture
- Gamma Curve and Main Color Settings
- White Balance
- Zooming
- Using Optional Conversion Lenses
- Adjusting the Focus
- Image Stabilization
- Onscreen Markers and Zebra Patterns
- Setting the Time Code
- Setting the User Bit
- Synchronizing with an External Device
- Recording Audio
- Audio Settings and Recorded Audio Channels
- Connecting an External Microphone or External Audio Input Source to the Camcorder
- Setting the Audio Input Type for the INPUT 1/INPUT 2 Terminals
- Selecting the Audio Input Source for Audio Channels
- Adjusting the Audio Recording Level
- Advanced Audio Input Settings
- Monitoring the Audio with Headphones
- Colors Bars/Audio Reference Signal
- Waveform Monitor
- Adding Marks to Clips while Recording
- Using Metadata
- Recording GPS Information (Geotagging)
- Reviewing a Recording
- Special Recording Modes
- Infrared Recording
- Customization
- Playback
- External Connections
- Network Functions
- Photos
- Additional Information
Browser Remote: Controlling the Camcorder from a Network Device
166
1 Live view screen
Shows the camcorder’s live view image. When the live view image is not turned on, the camcorder ID will
appear here.
2 Status indicators
3 [LIVE VIEW] button
Touch the button to display the camcorder’s live view image on the Browser Remote screen.
4[Shot Mark] button
While recording, touch the button to add a shot mark to the clip. When the [Shot Mark] message appears,
touch [ ].
5 Clip marks buttons
When recording, you can tag important clips by adding clip marks (A 107).
To add a clip mark
: After recording a clip, touch [ Mark] to add an
$
mark to the clip, or [ Mark] to add
a
%
mark to the clip. When the [OK Mark] or [CHECK Mark] message appears, touch .
6Browser Remote screen selection ([Full] user only)
Touch [
v
] to open the main remote recording screen, [ ] to open the metadata screen (A 170), or [ ] to
open the basic screen for devices with a small screen (A 172).
7 [FULL AUTO] button
To set the camcorder to full auto mode (A 43), touch [Off], select [On] and then touch [ ].
8 Language selection
Changes the language used for controls in the [ ] (metadata input) screen and for error messages. Still,
most of the application’s controls emulate physical buttons on the camcorder and appear in English only,
regardless of the language selected.
9Key lock button
Touch the icon to lock the Browser Remote screens in order to prevent settings from being changed
inadvertently.
10 [
D
Touch Focus] button
Touch the button to unlock (enable) the touch focus mode.
NOTES
• The live view image will not be displayed in Browser Remote in the following cases.
- While the color bars are displayed.
- When the resolution is 2340x2160, the frame rate is 59.94P or 50.00P and > [B " System
Setup] > [SDI/HDMI Max Res.] is set to [3840x2160].
: Wi-Fi connection indicator. While Browser Remote is correctly connected to the camcorder, the
dots will keep turning on and off in a loop.
STBY, etc. : Recording operation (same as on the camcorder, A 46).
STBY
`
, REC
`
: Output recording command (A 186).
4
: Appears during double slot recording (A 36).
: Infrared recording (A 116)
è
, etc. : Remaining battery charge (A 45)
NOTES
• Depending on the Wi-Fi connection’s strength, there may be delay of 0.5 seconds or more between the
frame shown when you touch the button and the frame to which the camcorder adds the shot mark.