Owner's Manual
Table Of Contents
- Instruction Manual
- Highlights of the Camcorder
- Table of contents
- 1. Introduction
- 2. Preparations
- 3. Recording
- Recording Clips and Photos
- Video Configuration: Resolution, Bit Rate and Frame Rate
- Slow & Fast Motion Recording
- Shooting Modes
- Exposure Adjustment
- Automatic Gain Control (AGC) Limit
- White Balance
- Using Looks
- Zooming
- Focus Adjustment
- Image Stabilization
- Setting the Time Code
- Setting the User Bit
- Recording Audio
- Selecting the Audio Recording Format
- Audio Settings and Recorded Audio Channels
- Connecting an External Microphone or External Audio Input Source to the Camcorder
- Using Line Input or an External Microphone Connected to an INPUT Terminal
- Audio Recording Level (INPUT Terminals)
- Adjusting the Microphone’s Sensitivity (INPUT terminals)
- Microphone Attenuator (INPUT terminals)
- Using the Built-in Microphone or an External Microphone Connected to the MIC Terminal
- Audio Recording Level (Built-in Microphone/MIC Terminal)
- Microphone Sensitivity (Built-in Microphone)
- Microphone Attenuator (Built-in Microphone or MIC Terminal)
- Low-Cut Filter (Built-in Microphone or MIC Terminal)
- Using Headphones
- Color Bars/Audio Reference Signal
- Pre-Recording
- Onscreen Displays
- Infrared Recording
- Using the Optional RC-V100 Remote Controller
- Using the GP-E2 GPS Receiver
- 4. Customization
- 5. Playback
- 6. External Connections
- 7. Saving Clips
- 8. Additional Information
- Quick Guide
- Important Usage Instructions
- Precautions About the Battery Pack
- Supplied Accessories
- Table of Contents
- Names of Parts
- Charging the Battery Pack
- Basic Preparations
- Setting the Date, Time and Language
- Using SD Cards
- Recording Clips and Photos
- Playing Back and Saving Clips and Photos
- Connecting to an External Monitor
- Onscreen Icons and Displays
- Safety Instructions and Handling Precautions
- Others
- Abridged Specifications
- Additional Information
- Warranty
Menu Options
106
[Æ Recording Setup] menu
[Available Space in Memory]/[Used Space in Memory]: Displays a screen where you can verify how much
of the SD card is currently available for recording or how much is in use (« total recording time and
ª total number of photos).
• Estimated figures about available clip recording time and available number of photos are
approximate and based on the video configuration currently in use and a photo size of 1920x1080.
• You can also check the SD card's Speed Class.
[HDMI Time Code]: When set to [i On], the HDMI signal output from the camcorder includes the
camcorder's time code.
Menu item Setting options A
[¸ Resolution] [3840x2160 (150 Mbps)], [1920x1080 (35 Mbps)],
[1920x1080 (17 Mbps)], [1280x720 (8 Mbps)]
– 37
[¸ Frame Rate] [¼ 59.94P], [» 29.97P], [º 23.98P] – 37
[¸ Audio Format] [ AAC 16bit 2CH], [ LPCM 16bit 4CH] – 68
[Recording Media] [v Rec Media for Movies]:
[
6 Mem. Card A], [7 Mem. Card B]
– 32
[{ Rec Media for Photos]:
[
6 Mem. Card A], [7 Mem. Card B]
–
[Dual/Relay
Recording]
[v Standard Recording], [4 Dual Recording],
[ Relay Recording] (or [ Relay Recording])
– 32
[Slow & Fast Motion] [OFF], [x0.4], [x0.5], [x0.8], [x2], [x4], [x10], [x20], [x60], [x120],
[x600], [x1200]
– 38
[Available Space in
Memory]
[6], [7] – –
[Used Space in
Memory]
[6], [7] – –
[Initialize 8] [6 Mem. Card A], [7 Mem. Card B] 32
[Rec Command] [i On], [j Off] – 35
[HDMI Time Code] [i On], [j Off] – –
[Time Code Mode] [ Preset], [ Regen.] – 64
[Time Code Running
Mode]
[ Rec Run], [ Free Run] – 64
[DF/NDF] [ DF], [ NDF] – 66
[Initial Time Code] 00:00:00.00 to 23:59:59.29, [Reset] – 65
[User Bit Type] [ Setting], [ Time], [ Date];
[i]: user bit input screen (00 00 00 00
to FF FF FF FF).
– 67
[Color Bars] [j Off], [ SMPTE], [ ARIB] – 77
[1 kHz Tone] [ü –12 dB], [þ –18 dB], [ÿ –20 dB], [j Off] – 77
[MP4 Clip / Photo
Numbering]
[m Reset], [n Continuous] –