Owner's Manual
Table Of Contents
- Instruction Manual
- Highlights of the Camcorder
- Table of contents
- 1. Introduction
- 2. Preparations
- 3. Recording
- Recording Clips and Photos
- Video Configuration: Resolution, Bit Rate and Frame Rate
- Slow & Fast Motion Recording
- Shooting Modes
- Exposure Adjustment
- Automatic Gain Control (AGC) Limit
- White Balance
- Using Looks
- Zooming
- Focus Adjustment
- Image Stabilization
- Setting the Time Code
- Setting the User Bit
- Recording Audio
- Selecting the Audio Recording Format
- Audio Settings and Recorded Audio Channels
- Connecting an External Microphone or External Audio Input Source to the Camcorder
- Using Line Input or an External Microphone Connected to an INPUT Terminal
- Audio Recording Level (INPUT Terminals)
- Adjusting the Microphone’s Sensitivity (INPUT terminals)
- Microphone Attenuator (INPUT terminals)
- Using the Built-in Microphone or an External Microphone Connected to the MIC Terminal
- Audio Recording Level (Built-in Microphone/MIC Terminal)
- Microphone Sensitivity (Built-in Microphone)
- Microphone Attenuator (Built-in Microphone or MIC Terminal)
- Low-Cut Filter (Built-in Microphone or MIC Terminal)
- Using Headphones
- Color Bars/Audio Reference Signal
- Pre-Recording
- Onscreen Displays
- Infrared Recording
- Using the Optional RC-V100 Remote Controller
- Using the GP-E2 GPS Receiver
- 4. Customization
- 5. Playback
- 6. External Connections
- 7. Saving Clips
- 8. Additional Information
- Quick Guide
- Important Usage Instructions
- Precautions About the Battery Pack
- Supplied Accessories
- Table of Contents
- Names of Parts
- Charging the Battery Pack
- Basic Preparations
- Setting the Date, Time and Language
- Using SD Cards
- Recording Clips and Photos
- Playing Back and Saving Clips and Photos
- Connecting to an External Monitor
- Onscreen Icons and Displays
- Safety Instructions and Handling Precautions
- Others
- Abridged Specifications
- Additional Information
- Warranty
Connecting to an External Monitor
97
s Using the SDI OUT Terminal
The digital signal that is output from the SDI OUT terminal includes the video signal, audio signal, time
code and recording command. You can output also the onscreen displays (A 108).
Make sure the SDI OUT terminal is set for output in advance (A 96).
1 Select [SDI Output].
> [£!Display Setup] > [SDI Output]
2 Select the desired maximum resolution and then select [L].
3 Select [3G-SDI Mapping].
> [£!Display Setup] > [3G-SDI Mapping]
4 Select the desired option and then select [L].
• You can select a video output signal compliant with Level A or Level B of the SMPTE ST 425-1
standard.
NOTES
• The time code signal will not be output from the SDI OUT terminal when slow & fast motion
recording is activated.
• The frames value in the time code will run from 0 to 29 instead of 0 to 23 in the following cases.
- > [£ Display Setup] > [SDI/HDMI Scan Mode] is [ PsF (Forced 1080i)] and the
frame rate is 23.98P.
- When the output is 1280x720.
• You can set > [
3
Recording Setup] > [Rec Command] to [i On] to use the
camcorder’s START/STOP button to control also the recording operation of an external recorder
connected to the SDI OUT terminal.
Using the HDMI OUT Terminal
The digital signal that is output from the HDMI OUT terminal includes the video signal and audio signal.
You can output also the time code signal and some assistance displays (onscreen displays, markers,
etc.) in order to check them also on an external monitor. s Make sure the HDMI OUT terminal is
set for output in advance (A 96).
The audio output signal will be 2-channel linear PCM audio (16-bit, 48 kHz sampling).
1 Select [HDMI Max Resolution].
> [£!Display Setup] > [HDMI Max Resolution]
2 Select the desired maximum resolution and then select [L].
3 mode only: To output the time code signal, select [HDMI Time Code].
> [
3
" Recording Setup] > [HDMI Time Code]
4 Select [On] and then select [X].