Owner's Manual
Table Of Contents
- Safety Instructions
- Table of Contents
- 1. Introduction
- 2. Preparations
- 3. Recording
- Recording Video and Photos
- Adjusting Camera and Recording Settings
- Video Recording Configuration: Video Format, System Frequency, Resolution and Frame Rate
- Proxy Clips
- Sub Recording Clips
- Shutter Speed
- ISO Speed/Gain
- ND Filter
- Aperture
- White Balance
- Zoom
- Focus
- Image Stabilization
- Onscreen Markers, Zebra Patterns and False Color
- Setting the Time Code
- Synchronizing with an External Device
- Recording Audio
- Audio Format for MP4 Clips
- Recording Audio Using the Second Card Recording Functions
- Connecting an External Microphone or External Audio Input Source to the Camera
- Selecting the Audio Input Source for Audio Channels
- Adjusting the Audio Recording Level
- Advanced Audio Input Settings
- Monitoring the Audio with Headphones
- Colors Bars/Audio Reference Signal
- Video Scopes
- Adding Marks to Clips in CAMERA Mode
- Using Metadata
- Special Recording Modes
- Infrared Recording
- Using the RC-V100 Remote Controller
- Recording Remotely Using an NU Protocol Compatible Device
- Web Camera Function
- 4. Customization
- 5. Playback
- 6. External Connections
- 7. Network Functions
- 8. Additional Information
Special Recording Modes
106
1
> [
Æ
Recording/Media Setup] >[Main Rec Format].
2
> [
Æ
Recording/Media Setup] > [Main Resolution/Bit rate]
1 To record audio, insert an SD card into the card slot where video is not being recorded.
2 Select > [Æ Recording/Media Setup] > [Recording Mode] > [Slow & Fast Motion] or [S&F
Clip/Audio (WAV)].
• Slow & fast motion recording is activated. [S&F STBY] appears on the screen and the shooting frame rate
appears next to the frame rate setting (the playback frame rate).
3 Select > [Æ Recording/Media Setup] > [Slow & Fast Frame Rate] > Desired frame rate.
• You can also choose a preset value (half, same or double the playback frame rate).
4Press the REC button to begin recording.
• The tally lamp changes from green (power indicator) to red.
• [S&F STBY] changes to [S&F ÜREC] while recording.
5Press the REC button again to stop recording.
• The clip is recorded on the selected SD card.
• When [S&F Clip/Audio (WAV)] is selected, the WAV file will be recorded on the SD card where video is not
being recorded.
• The tally lamp changes from red to green (power indicator) and the onscreen display changes back to [S&F
STBY].
6 Select > [Æ Recording/Media Setup] > [Recording Mode] > [Normal Recording] to turn off
slow & fast motion recording.
NOTES
NOTES
• The shooting frame rate cannot be changed while recording.
• If you change the system frequency, slow & fast motion recording will be canceled and the shooting frame rate
will be reset to its default value.
• About the time code when slow & fast motion recording is activated:
- The time code mode can be set to [Regen.], or to [Preset] with [Rec Run] running mode.
- If the time code running mode was set to [Free Run], the time code running mode will be changed
automatically to [Rec Run] when slow & fast motion recording is activated.
- When the special recording mode is turned off, the time code running mode will return to its previous setting.
- The time code signal will not be output from any terminal.
• Recording WAV files
- Audio is recorded with the following settings: 48 kHz, 24 bit, 4 channels.
- If video cannot be recorded due to a card problem, audio will also not be recorded.
- However, video will be recorded even if audio cannot be recorded due to a card problem.
- Audio will not be recorded if there is an existing WAV file with the same file name.
- Audio recording will stop automatically after reaching 60 minutes (video recording will continue).
- A maximum of 999 WAV files can be recorded.