Owner's Manual
Table Of Contents
- Safety Instructions
- Table of Contents
- 1. Introduction
- 2. Preparations
- 3. Recording
- Recording Video and Photos
- Adjusting Camera and Recording Settings
- Video Recording Configuration: Video Format, System Frequency, Resolution and Frame Rate
- Proxy Clips
- Sub Recording Clips
- Shutter Speed
- ISO Speed/Gain
- ND Filter
- Aperture
- White Balance
- Zoom
- Focus
- Image Stabilization
- Onscreen Markers, Zebra Patterns and False Color
- Setting the Time Code
- Synchronizing with an External Device
- Recording Audio
- Audio Format for MP4 Clips
- Recording Audio Using the Second Card Recording Functions
- Connecting an External Microphone or External Audio Input Source to the Camera
- Selecting the Audio Input Source for Audio Channels
- Adjusting the Audio Recording Level
- Advanced Audio Input Settings
- Monitoring the Audio with Headphones
- Colors Bars/Audio Reference Signal
- Video Scopes
- Adding Marks to Clips in CAMERA Mode
- Using Metadata
- Special Recording Modes
- Infrared Recording
- Using the RC-V100 Remote Controller
- Recording Remotely Using an NU Protocol Compatible Device
- Web Camera Function
- 4. Customization
- 5. Playback
- 6. External Connections
- 7. Network Functions
- 8. Additional Information
107
Special Recording Modes
Pre-recording
When pre-recording is activated, the camera starts recording continuously onto a temporary memory (approx.
3 seconds) so when you press the REC button, the clip will contain also a few seconds of video and audio
recorded before you pressed the button.
You can also use direct touch control to perform this function (A 49).
1 Select > [Æ Recording/Media Setup] > [Recording Mode] > [Pre-Recording].
• [PRE STBY] appears on the screen.
2Press the REC button to begin recording.
• The tally lamp changes from green (power indicator) to red.
• [PRE STBY] changes to [PRE
Ü
REC] while recording.
3Press the REC button again to stop recording.
• The clip is recorded. The recorded clip will include a few seconds of video and audio recorded before the
REC button was pressed.
• The tally lamp changes from red to green (power indicator) and the onscreen display changes back to [PRE
STBY].
4 Select > [Æ Recording/Media Setup] > [Recording Mode] > [Normal Recording] to stop
pre-recording.
NOTES
NOTES
• Pre-recording will be canceled if the recording mode is changed.
• About the time code when pre-recording is activated:
- The time code of the clip will start a few seconds before the REC button was pressed.
- The time code will be recorded with the running mode set to [Free Run].
- If the time code mode was set to [Regen.], or to [Preset] with [Rec Run] running mode, the time code
running mode will be changed automatically to [Free Run] when pre-recording is activated.
- When the special recording mode is turned off, the time code running mode will return to its previous
setting.
Frame Recording Mode
Set the number of frames in advance. We recommend operating the camera remotely or stabilizing the camera,
for example, on a tripod. Sound is not recorded in this mode.
You can also use direct touch control to perform this function (A 49).
1 Select > [
Æ
Recording/Media Setup] > [Recording Mode] > [Frame Recording].
• [FRM STBY] appears on the screen (with [FRM] flashing).
2 Select > [
Æ
Recording/Media Setup] > [Frame Rec: Frame Rate] > Desired option.
3Press the REC button to begin recording.
• The tally lamp illuminates.
• [FRM STBY] changes to [FRM ÜREC] while recording.
• The camera automatically records the specified number of frames.
4 Repeat until you finish recording.
5 Select > [
Æ
Recording/Media Setup] > [Recording Mode] > [Normal Recording] to stop frame
recording.
• Frame recording mode ends and all of the recorded frames are joined together into one clip.
• The tally lamp goes out and [STBY] appears on the screen.