Owner's Manual
Table Of Contents
- Safety Instructions
- Table of Contents
- 1. Introduction
- 2. Preparations
- 3. Recording
- Recording Video and Photos
- Adjusting Camera and Recording Settings
- Video Recording Configuration: Video Format, System Frequency, Resolution and Frame Rate
- Proxy Clips
- Sub Recording Clips
- Shutter Speed
- ISO Speed/Gain
- ND Filter
- Aperture
- White Balance
- Zoom
- Focus
- Image Stabilization
- Onscreen Markers, Zebra Patterns and False Color
- Setting the Time Code
- Synchronizing with an External Device
- Recording Audio
- Audio Format for MP4 Clips
- Recording Audio Using the Second Card Recording Functions
- Connecting an External Microphone or External Audio Input Source to the Camera
- Selecting the Audio Input Source for Audio Channels
- Adjusting the Audio Recording Level
- Advanced Audio Input Settings
- Monitoring the Audio with Headphones
- Colors Bars/Audio Reference Signal
- Video Scopes
- Adding Marks to Clips in CAMERA Mode
- Using Metadata
- Special Recording Modes
- Infrared Recording
- Using the RC-V100 Remote Controller
- Recording Remotely Using an NU Protocol Compatible Device
- Web Camera Function
- 4. Customization
- 5. Playback
- 6. External Connections
- 7. Network Functions
- 8. Additional Information
Special Recording Modes
108
NOTES
NOTES
• Frame recording cannot be used simultaneously with slow & fast motion recording, pre-recording, interval
recording or continuous recording.
• Frame recording cannot be used when the frame rate is set to 59.94i or 50.00i. When in use, frame recording
will end if the frame rate is set to 59.94i or 50.00i.
• The number of frames recorded cannot be changed while recording.
• Some frames at the point the recording was stopped may be recorded and added to the end of the clip.
• About the time code when frame recording is activated:
- The time code mode can be set to [Regen.], or to [Preset] with [Rec Run] running mode. The time code
advances by the number of frames recorded every time.
- If the time code running mode was set to [Free Run] or the camera was synchronized to an external time
code signal, the time code running mode will be changed automatically to [Rec Run] when frame recording
is activated.
- When the special recording mode is deactivated, the time code running mode will return to its previous
setting.
- The time code signal will not be output from the TIME CODE terminal, SDI OUT terminal or HDMI OUT
terminal.
Interval Recording Mode
Set the interval and number of frames in advance. Sound is not recorded in this mode.
You can also use direct touch control to perform this function (A 49).
1 Select > [
Æ
Recording/Media Setup] > [Recording Mode] > [Interval Recording].
• [INT STBY] appears at the top of the screen (with [INT] flashing).
2 Select > [
Æ
Recording/Media Setup] > [Interval Rec: Time Interval] > Desired option.
3 Select > [
Æ
Recording/Media Setup] > [Interval Rec: Frame Rate] > Desired option.
4Press the REC button to begin recording.
• The tally lamp illuminates.
• [INT STBY] changes to [INT ÜREC] while recording.
• The camera automatically records the set number of frames at the specified interval.
5Press the REC button again to stop recording.
• The tally lamp goes out and [INT STBY] appears at the top of the screen (with [INT] flashing).
6 Select > [
Æ
Recording/Media Setup] > [Recording Mode] > [Normal Recording] to stop interval
recording.
NOTES
NOTES
• Interval recording cannot be used simultaneously with slow & fast motion recording, pre-recording, frame
recording or continuous recording.
• Interval recording cannot be used when the frame rate is set to 59.94i or 50.00i. When in use, interval
recording will end if the frame rate is set to 59.94i or 50.00i.
• The interval and the number of frames recorded cannot be changed while recording.
• Some frames at the point the recording was stopped may be recorded and added to the end of the clip.
• When the special recording mode is deactivated, the time code running mode will return to its previous setting.
• The time code signal will not be output from the TIME CODE terminal, SDI OUT terminal or HDMI OUT
terminal.