Owner's Manual
Table Of Contents
- Safety Instructions
- Table of Contents
- 1. Introduction
- 2. Preparations
- 3. Recording
- Recording Video and Photos
- Adjusting Camera and Recording Settings
- Video Recording Configuration: Video Format, System Frequency, Resolution and Frame Rate
- Proxy Clips
- Sub Recording Clips
- Shutter Speed
- ISO Speed/Gain
- ND Filter
- Aperture
- White Balance
- Zoom
- Focus
- Image Stabilization
- Onscreen Markers, Zebra Patterns and False Color
- Setting the Time Code
- Synchronizing with an External Device
- Recording Audio
- Audio Format for MP4 Clips
- Recording Audio Using the Second Card Recording Functions
- Connecting an External Microphone or External Audio Input Source to the Camera
- Selecting the Audio Input Source for Audio Channels
- Adjusting the Audio Recording Level
- Advanced Audio Input Settings
- Monitoring the Audio with Headphones
- Colors Bars/Audio Reference Signal
- Video Scopes
- Adding Marks to Clips in CAMERA Mode
- Using Metadata
- Special Recording Modes
- Infrared Recording
- Using the RC-V100 Remote Controller
- Recording Remotely Using an NU Protocol Compatible Device
- Web Camera Function
- 4. Customization
- 5. Playback
- 6. External Connections
- 7. Network Functions
- 8. Additional Information
163
Configuring Connection Settings
IP Streaming
This section continues the connection settings wizard (A 161). In the function settings you will configure the
streaming video bit rate and resolution, the protocol used and the receiver’s settings. For details refer to the
instruction manual of the decoder device or software you will use.
1 Select [Create New Func. Setting].
• Once you have added multiple function settings, you can select [Select Existing Setting] to reuse IP
streaming settings that you saved previously.
2 Select the desired protocol.
3 Configure the receiver’s settings. Select [Destination Server] and [Dest. Port No.] > [OK].
• Enter the receiver’s IP address using the keyboard screen. Enter the port number using the data entry
screen (A 27).
• Using the default port number is recommended.
• Depending on the streaming protocol selected in step 2, perform step 4 if necessary and then continue to
step 5.
[RTP+FEC] streaming
4 Configure the settings used to send FEC packets. Select [FEC Port No.] and [FEC Interval] > [OK].
• Enter the port number using the data entry screen (A 27).
• Using the default settings is recommended.
[RTSP+RTP] streaming
4 Enter the user name and password of the RTSP client. Select [RTSP: User Name] and [RTSP: Password] >
[OK].
• Enter the desired user name and password using the keyboard screen (A 27).
All streaming protocols
5 Select the video streaming configuration.
6 Select the audio channels.
7 Depending on the resolution and frame rate, a screen may prompt you to change other settings. Change the
settings as necessary.
8 Select [OK].
• The function settings are saved to a [MODE] file.
9 Select the connection setting (SET1 to SET20) where to save the settings.
10 Select [OK].
• The camera will connect to the network and will be ready to start streaming.
11 Connect the decoder to the network and complete any necessary configurations on the receiving side so the
decoder is ready to receive video over IP.
• To start streaming, refer to
IP Streaming
(A 175).
Options for [Protocol]
[UDP]: This protocol prioritizes transfer speeds but does not guarantee the reliability/integrity of the
data. Lost or delayed IP packets are ignored.
[RTP]: Standard protocol for video/audio broadcasts over the Internet. Lost or delayed IP packets are
ignored.
[RTP+FEC]: This setting uses the RTP protocol and adds a layer of FEC error correction so the receiving
side* can recover lost or delayed IP packets.
[RTSP+RTP]: This setting uses the RTSP (real time streaming) protocol to control the streaming server
(camera) in real time and the RTP protocol for the broadcast over IP. With the RTSP protocol,
the receiver can control when to start and stop the broadcast.