Owner's Manual
Table Of Contents
- Safety Instructions
- Table of Contents
- 1. Introduction
- 2. Preparations
- 3. Recording
- Recording Video and Photos
- Adjusting Camera and Recording Settings
- Video Recording Configuration: Video Format, System Frequency, Resolution and Frame Rate
- Proxy Clips
- Sub Recording Clips
- Shutter Speed
- ISO Speed/Gain
- ND Filter
- Aperture
- White Balance
- Zoom
- Focus
- Image Stabilization
- Onscreen Markers, Zebra Patterns and False Color
- Setting the Time Code
- Synchronizing with an External Device
- Recording Audio
- Audio Format for MP4 Clips
- Recording Audio Using the Second Card Recording Functions
- Connecting an External Microphone or External Audio Input Source to the Camera
- Selecting the Audio Input Source for Audio Channels
- Adjusting the Audio Recording Level
- Advanced Audio Input Settings
- Monitoring the Audio with Headphones
- Colors Bars/Audio Reference Signal
- Video Scopes
- Adding Marks to Clips in CAMERA Mode
- Using Metadata
- Special Recording Modes
- Infrared Recording
- Using the RC-V100 Remote Controller
- Recording Remotely Using an NU Protocol Compatible Device
- Web Camera Function
- 4. Customization
- 5. Playback
- 6. External Connections
- 7. Network Functions
- 8. Additional Information
Menu Options
196
1
The default value depends on the country/region of purchase.
2
Only when the GP-E2 GPS Receiver is connected to the camera.
[
¥
My Menu] menu (CAMERA mode only)
[Genlock Adjustment]
2
–1023 to +1023 (000) (A 89)
The phase difference between the external Genlock signal and the camera is initially set to 0. This setting
allows you to adjust it within the range of approx. ±0.4 H (–1023 to 1023). To set a 4-digit adjustment
value, set the first field to 10 or –10.
[SYNC Scan Mode] [P], [PsF] (A 90)
[Key Lock] [All Buttons], [All Except REC Button] (A 15)
[REC Button] [Disable], [Enable]
Enables or disables the use of the REC buttons.
[Onscreen REC/STBY Button] [On], [Off] (A 42)
When this setting is set to [On], the recording operation indicator (REC/STBY) on the CAMERA mode
screen becomes an onscreen button you can touch to start/stop recording.
[Touch Screen Response] [Normal], [Low] (A 23)
[Power Supply LED] [On], [Off] (A 14)
When this setting is set to [Off], the power indicator will not illuminate even when the camera is powered
on.
[Tally Lamp (Front)],
[Tally Lamp (Rear)],
[SD Card Access LED]
[On], [Off]
These settings determine whether the following LEDs and indicators will illuminate.
[Tally Lamp (Front)], [Tally Lamp (Rear)]: The tally lamp (A 14, 17) while recording.
[SD Card Access LED]: The card access indicator (A 32) when the camera is accessing the card.
[Fan Mode] [Automatic], [Always On] (A 40)
[Review Recording] [Entire Clip], [Last 4 sec] (A 48)
[GPS Auto Time]
2
[On], [Off]
When this setting is set to [On], the camera automatically adjust its date and time settings according to
the information received from the GPS signal.
• While the automatic date/time adjustment is activated, the > [
B
System Setup] > [Date/
Time] setting will not be available.
• The time will not be updated while recording video.
[USB (Type-C) Mode] [Video Output (UVC)], [Canon App(s) for iPhone], [PTP Connection/GP-E2] (A 113)
Select [PTP Connection/GP-E2] when connecting the GP-E2 GPS Receiver to the camera using an optional
interface cable.
[DC IN Warning (V)] 11.5 V to 15.0 V in 0.1 V intervals (13.0 V) (A 22)
[Reset Hour Meter] The camera has two “hour meters” – the first keeps track of total operation time and the second keeps
track of operation time since the last time the second hour meter was reset with this function.
[Certification Information] This displays select certification information that apply to this camera.
[Firmware]
[Camera] Check/update the firmware version of the camera.
Menu item Setting options and additional information
[CAMERA-1: Edit] to
[CAMERA-5: Edit]
[Register], [Move], [Delete], [Reset All], [Rename] (A 26)
Menu item Setting options and additional information